Study guide

10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance

HVAC Excellence Certification Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction, Safety, Tools, and Diagnostic Method

1.1 HVAC Excellence Certification, Industry Codes, and Standards 1.2 Electrical Safety, PPE, Lockout/Tagout, and Hazard Communication 1.3 Multimeters, Manifold Gauges, Micron Gauges, and Diagnostic Instruments 1.4 HVACR Mathematics, Unit Conversions, and Efficiency Ratings 1.5 OSHA Standards, Fall Protection, Rigging, and Confined Spaces 1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs 1.7 Systematic Troubleshooting: Data Plates, Manufacturer Literature, and Diagnostic Method

2 Chapter 2: Electrical Fundamentals and Circuit Theory

2.1 Voltage, Current, Resistance, and Ohm's Law Calculations 2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations 2.3 AC Fundamentals, Single-Phase vs Three-Phase Power, and Control Transformers 2.4 Conductors, Insulators, Wire Sizing, Voltage Drop, and NEC Ampacity

3 Chapter 3: Electrical Components, Motors, and Schematics

3.1 Contactors, Relays, Switches, Overload Protection, and Thermostats 3.2 HVAC Motors (PSC, CSIR, CSCR, ECM, 3-Phase) and Run/Start Capacitors 3.3 Interpreting Ladder Diagrams, Schematics, and Point-to-Point Wiring 3.4 Motor Testing, Insulation Resistance, Bearings, and Belt Drives

4 Chapter 4: Thermodynamics and the Refrigeration Cycle

4.1 Heat Transfer, Temperature Scales, BTUs, Sensible vs Latent Heat, and Enthalpy 4.2 The Four Vapor-Compression Cycle Stages (Compression, Condensation, Expansion, Evaporation) 4.3 P-T Charts, Saturated Conditions, Target Superheat, and Subcooling Calculations 4.4 Pressure–Enthalpy Diagrams, Compression Ratio, and Cycle Analysis

5 Chapter 5: Refrigerants, Environmental Regulations, and Recovery

5.1 Refrigerant Types (CFC, HCFC, HFC, HFO, HC) and ASHRAE Safety Groups (A1, A2L, A3) 5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards 5.3 Recovery/Recycling/Reclaiming Equipment, Procedures, and Leak Detection 5.4 Refrigerant Retrofits, Cylinder Handling, and Refrigerant Purity 5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice

6 Chapter 6: Refrigeration System Components and Accessories

6.1 Compressor Mechanics (Reciprocating, Scroll, Rotary, Screw) and Failures 6.2 Expansion Devices (TXV/TEV, Fixed Orifice, EEV) and Superheat Control 6.3 Condensers, Evaporators, Filter-Driers, Accumulators, Receivers, and Solenoids 6.4 Pressure Controls, Capacity Controls, and System Protection 6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice

7 Chapter 7: Gas Heating, Combustion Analysis, and Fuel Piping

7.1 Combustion Theory, Fuel Gases (Natural Gas vs LP), and Gas Burners 7.2 Gas Valves, Ignition Systems (Standing Pilot, Spark, HSI), and Safety Limit Controls 7.3 Flue Venting, Draft Principles, Combustion Analysis, and CO Safety 7.4 Fuel-Gas and Oil Piping, Vent System Selection and Sizing, and Installation Practice

8 Chapter 8: Electric Heating, Oil Heat, and Hydronics

8.1 Electric Heating Elements, Sequencers, Limit Switches, and kW Calculations 8.2 Oil Burners, Fuel Pumps, Nozzles, Ignition Electrodes, and Primary Controls 8.3 Hydronic Boilers, Circulator Pumps, Expansion Tanks, and Zone Controls 8.4 Combustion Air, Water Heaters, and Combustion Appliance Zone Testing

9 Chapter 9: Heat Pumps and Dual-Fuel Systems

9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation 9.2 Defrost Controls (Time-Temperature, Demand Defrost), Sensors, and Sequences 9.3 Balance Points, Auxiliary/Emergency Heat, and Dual-Fuel (Hybrid) Systems 9.4 Heat Pump Diagnostics, Refrigerant Flow, and Troubleshooting Procedures 9.5 Heat Pump Types, Cold-Climate Performance, and Sizing Approaches

10 Chapter 10: Air Distribution, IAQ, and System Commissioning

10.1 Airflow Fundamentals, CFM Measurement, External Static Pressure, and Fan Laws 10.2 Duct Sizing Principles, Supply/Return Distribution, Dampers, and Air Balancing 10.3 Indoor Air Quality, MERV Ratings, Electronic Cleaners, Humidification, and Dehumidification 10.4 Deep Vacuum Evacuation (Micron Gauge), Subcooling/Superheat Charging, and System Commissioning 10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance

11 Chapter 11: Psychrometrics, Airside Calculations, and Load Estimation

11.1 Reading the Psychrometric Chart: Properties and Plotting 11.2 The Eight Air-Conditioning Processes and the Process Triangle 11.3 Mixed Air, Ventilation, and Infiltration Calculations 11.4 Residential Heat Loss, Heat Gain, and Equipment Sizing

12 Chapter 12: Light Commercial Air Conditioning

12.1 Packaged Rooftop and Split Light-Commercial Systems 12.2 Water-Cooled Condensers, Cooling Towers, and Chilled-Water Systems 12.3 Economizers, Demand-Controlled Ventilation, and VAV Air Distribution 12.4 Light-Commercial Start-Up, Commissioning, and Troubleshooting

13 Chapter 13: Light Commercial Refrigeration

13.1 Temperature Ranges, Box Loads, and Refrigeration System Types 13.2 Evaporators, Defrost Methods, and Defrost Controls 13.3 Condensing Units, Parallel Racks, Oil Management, and Capacity Control 13.4 Refrigeration Control Valves and Automatic Pump-Down 13.5 Commercial Refrigeration Diagnostics and Ice Machines

14 Chapter 14: Ductless, Mini-Split, and VRF Systems

14.1 Mini-Split Architecture and Inverter-Driven Compressors 14.2 Multi-Zone and VRF Operation, Electronic Expansion Valves, and Controls 14.3 Ductless Installation, Evacuation, Charging, and Diagnostics

15 Chapter 15: Building Automation and Digital Controls

15.1 DDC Fundamentals, Control Loops, and Sequences of Operation 15.2 BAS Networks, Protocols, and NEC-Compliant Cabling 15.3 Building Automation Controllers: Supervisory, Field, and Room Devices 15.4 Digital Logic, Numbering Systems, and Controller Programming 15.5 Sensor Selection, Installation, and Input Point Configuration 15.6 Actuators, Output Devices, and VFD Integration 15.7 Commercial Prints, Equipment Schedules, and BAS Documentation

10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance

Key Takeaways Explain This Topic AI

A blower door depressurizes the house to 50 pascals and reports airflow as CFM50, which divided into the conditioned volume and multiplied by 60 gives ACH50.

ACH50 equals CFM50 times 60 divided by conditioned volume in cubic feet; a house at 1,800 CFM50 with 16,000 cubic feet tests at 6.75 ACH50.

Duct leakage is measured at 25 pascals with a duct blaster; total leakage includes all leaks, while leakage to outside is measured with the blower door running to neutralize house pressure.

Duct leakage in unconditioned space is the costly kind: return leakage pulls attic or crawlspace air into the system and supply leakage pressurizes those spaces.

Tightening a building envelope without verifying combustion appliance draft can create a depressurization hazard, which is why blower door work and CAZ testing are performed together.

Last updated: August 2026

10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance

The Duct & Envelope sheet of the HVAC Excellence Competency and Task List is short but dense. It requires the technician to understand the basics of building science, identify and set up the components of a blower door, perform blower door and duct leakage tests, calculate conditioned volume , ACH50 , and duct leakage rates , determine maximum allowable testing static pressure, and carry out carbon monoxide testing and safe-entry protocol. It backs the Duct and Envelope Testing Specialty Certification and the Master Specialist Duct Leak Testing and Envelope Leak Testing hands-on exams.

1. The Building Science Behind the Test

A building is a pressure boundary, and air moves across it whenever a pressure difference exists. Three drivers:

Stack effect — warm indoor air rises, exits high, and draws replacement air in low. The neutral pressure plane sits where indoor and outdoor pressure are equal; above it the house is positive to outdoors, below it negative. This is why attic leaks dominate winter heat loss and why a basement is where cold air enters.

Wind — positive pressure on the windward face, negative on the leeward and roof.

Mechanical — exhaust fans, clothes dryers, unbalanced duct leakage, and closed-door pressures created by the air handler.

Air leakage carries heat and moisture. Moisture is the destructive part : warm humid air moving into a cold cavity condenses on the first surface below dew point, producing rot and mold. That is why air sealing matters more than insulation R-value in many retrofits.

The house is a system. Tightening the envelope reduces infiltration, which reduces the makeup air available to natural-draft combustion appliances. Envelope work and combustion-safety testing (Section 8.4) are never done separately.

2. The Blower Door

Components: an adjustable aluminum frame with an airtight nylon panel that seals into an exterior door opening; a variable-speed calibrated fan with interchangeable flow rings; a two-channel digital manometer measuring house-to-outdoor pressure on one channel and fan pressure (converted to flow) on the other; and reference tubing run to the exterior.

Setup procedure

Set the house to test conditions : exterior doors and windows closed and latched; interior doors open (so the whole conditioned volume is one zone); dampers, fireplace flues, and exhaust fans off; combustion appliances turned off or set so they cannot fire during the test ; ashes cleaned or covered.

Do not seal intentional openings for the standard single-point test — the goal is to measure the house as it operates.

Install the frame in a door that is not near a large obstruction, mount the fan, and run the reference hose outdoors away from wind and away from the fan discharge.

Take a baseline house pressure with the fan sealed, to correct for wind and stack effect.

Depressurize the house to −50 pascals with respect to outdoors and record the fan flow.

The primary result is CFM50 — the airflow required to hold the house at 50 Pa, which equals the leakage area's airflow at that pressure.

The ACH50 calculation ACH50 = CFM50 × 60 Conditioned volume (ft 3 ) \text{ACH50} = \frac{\text{CFM50} \times 60}{\text{Conditioned volume (ft}^3)} ACH50 = Conditioned volume (ft 3 ) CFM50 × 60 ​

Conditioned volume is the volume inside the pressure boundary — conditioned floor area times average ceiling height, including conditioned basements and, where the boundary is at the roofline, conditioned attics. It excludes vented crawlspaces, vented attics, and unconditioned garages.

Worked example. A 2,000 sq ft house with 8-foot ceilings plus a 900 sq ft conditioned basement with 7-foot ceilings: V = ( 2,000 × 8 ) + ( 900 × 7 ) = 16,000 + 6,300 = 22,300 ft 3 V = (2{,}000 \times 8) + (900 \times 7) = 16{,}000 + 6{,}300 = 22{,}300\text{ ft}^3 V = ( 2 , 000 × 8 ) + ( 900 × 7 ) = 16 , 000 + 6 , 300 = 22 , 300 ft 3

The blower door reads 2,100 CFM50 : ACH50 = 2,100 × 60 22,300 = 126,000 22,300 = 5.65 \text{ACH50} = \frac{2{,}100 \times 60}{22{,}300} = \frac{126{,}000}{22{,}300} = 5.65 ACH50 = 22 , 300 2 , 100 × 60 ​ = 22 , 300 126 , 000 ​ = 5.65

Interpreting the number

  • ACH50 Character
  • Below 1.0 Passive-house tight; mechanical ventilation mandatory
  • 1.0–3.0 Very tight new construction; mechanical ventilation required
  • 3.0–5.0 Current code-level new construction in most climate zones
  • 5.0–10.0 Typical existing house
  • Above 10.0 Leaky; large air-sealing opportunity

The IECC requires 3 ACH50 or less in climate zones 3 through 8 and 5 ACH50 or less in zones 1 and 2, verified by test. Below roughly 3 ACH50 a house cannot be assumed to ventilate itself, and ASHRAE 62.2 mechanical whole-building ventilation becomes a requirement, not an option (Section 1.1).

A leaky structure versus a tight structure — a task-list comparison — comes down to control. A leaky house ventilates unpredictably: too much in January, almost none on a mild day, and always through the dirtiest path available. A tight house ventilates by design, through a filtered, measured, often heat-recovering path.

3. Duct Leakage Testing

Duct leakage is measured with a duct blaster : a small calibrated fan connected to the duct system (usually at a return or the air handler cabinet) with all supply and return registers temporarily sealed.

The reference pressure is 25 pascals , chosen to approximate operating duct pressure. The result is CFM25 .

Two distinct tests

Test Setup What it measures

Total duct leakage Duct blaster only; registers sealed; house pressure irrelevant All leakage, including leaks into conditioned space

Leakage to outside Duct blaster and blower door running simultaneously, both holding the house and the ducts at the same pressure Only leakage that crosses the pressure boundary — the leakage that costs money

Running both fans neutralizes the pressure difference between the ducts and the house, so leaks into conditioned space move no air and only leaks to unconditioned space register. Leakage to outside is the number that matters for energy and for safety.

Expressing the result

Duct leakage is normalized to conditioned floor area: Leakage (%) = CFM25 Conditioned floor area (sq ft) × 100 \text{Leakage (\%)} = \frac{\text{CFM25}}{\text{Conditioned floor area (sq ft)}} \times 100 Leakage (%) = Conditioned floor area (sq ft) CFM25 ​ × 100

The IECC post-construction limit is commonly 4 CFM25 per 100 sq ft of conditioned floor area for total leakage, and rough-in testing allows a tighter number because the air handler may not be installed. A 2,000 sq ft house at 4% would be allowed 80 CFM25 .

Why duct leakage is worse than envelope leakage

Return leakage in an attic or crawlspace pulls unconditioned, often contaminated air directly into the supply airstream — attic air at 130°F in summer, crawlspace air carrying moisture, radon, or pesticide.

Supply leakage in an attic dumps conditioned air outside the boundary and depressurizes the house , drawing replacement air through every other leak — including, potentially, through a natural-draft appliance's flue.

Leakage occurs at connections, boots, plenum seams, and the air handler cabinet . Seal with mastic or mastic-backed tape, not cloth duct tape, which fails within a few years.

Related airside measurements the sheet requires

Determine maximum allowable testing static pressure — do not exceed the duct system's construction class or the manufacturer's limit, and never pressurize flex duct beyond its rating.

Measuring static pressure and finding CFM with an anemometer are covered in Section 10.1; the same instruments serve both competencies.

Duct R-value: insulation requirements depend on location — commonly R-8 for ducts in unconditioned attics and R-6 elsewhere outside the conditioned space in most climate zones. Sizing insulation also prevents surface condensation on cold supply ducts in humid spaces.

4. Carbon Monoxide Testing and Safe Entry

The Duct & Envelope sheet devotes seven separate lines to carbon monoxide, opening with the blunt statement that carbon monoxide is deadly .

Sources: any incomplete combustion — furnaces, water heaters, boilers, ranges, fireplaces, generators, vehicles in attached garages, and any appliance that is backdrafting.

Health effects: CO binds to hemoglobin roughly 200 times more readily than oxygen, forming carboxyhemoglobin and starving tissue of oxygen. Symptoms progress from headache and nausea to confusion, unconsciousness, and death, and they mimic flu — which is why CO poisoning is routinely misdiagnosed.

Safe entry protocol: test the air before entering. Wear a personal CO monitor. At 35 ppm ambient, ventilate and investigate; at 70 ppm , evacuate occupants; at 100 ppm and above , evacuate immediately and do not re-enter without ventilation and monitoring. Never rely on smell — CO is odorless, and the odors sometimes present come from other combustion byproducts.

Instruments: a low-level personal CO monitor for occupied space, and a combustion analyzer measuring undiluted flue CO (Section 7.3 and 8.4). Consumer UL 2034 alarms do not annunciate until roughly 70 ppm sustained for over an hour, so they are a life-safety backstop, not a diagnostic tool.

Do the CAZ test whenever you tighten a house. Air sealing that reduces ACH50 from 9 to 4 has removed the makeup air a natural-draft water heater was relying on. Verify draft and spillage before you leave.