Study guide
15.6 Actuators, Output Devices, and VFD Integration
HVAC Excellence Certification Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction, Safety, Tools, and Diagnostic Method
1.1 HVAC Excellence Certification, Industry Codes, and Standards 1.2 Electrical Safety, PPE, Lockout/Tagout, and Hazard Communication 1.3 Multimeters, Manifold Gauges, Micron Gauges, and Diagnostic Instruments 1.4 HVACR Mathematics, Unit Conversions, and Efficiency Ratings 1.5 OSHA Standards, Fall Protection, Rigging, and Confined Spaces 1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs 1.7 Systematic Troubleshooting: Data Plates, Manufacturer Literature, and Diagnostic Method
2 Chapter 2: Electrical Fundamentals and Circuit Theory
2.1 Voltage, Current, Resistance, and Ohm's Law Calculations 2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations 2.3 AC Fundamentals, Single-Phase vs Three-Phase Power, and Control Transformers 2.4 Conductors, Insulators, Wire Sizing, Voltage Drop, and NEC Ampacity
3 Chapter 3: Electrical Components, Motors, and Schematics
3.1 Contactors, Relays, Switches, Overload Protection, and Thermostats 3.2 HVAC Motors (PSC, CSIR, CSCR, ECM, 3-Phase) and Run/Start Capacitors 3.3 Interpreting Ladder Diagrams, Schematics, and Point-to-Point Wiring 3.4 Motor Testing, Insulation Resistance, Bearings, and Belt Drives
4 Chapter 4: Thermodynamics and the Refrigeration Cycle
4.1 Heat Transfer, Temperature Scales, BTUs, Sensible vs Latent Heat, and Enthalpy 4.2 The Four Vapor-Compression Cycle Stages (Compression, Condensation, Expansion, Evaporation) 4.3 P-T Charts, Saturated Conditions, Target Superheat, and Subcooling Calculations 4.4 Pressure–Enthalpy Diagrams, Compression Ratio, and Cycle Analysis
5 Chapter 5: Refrigerants, Environmental Regulations, and Recovery
5.1 Refrigerant Types (CFC, HCFC, HFC, HFO, HC) and ASHRAE Safety Groups (A1, A2L, A3) 5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards 5.3 Recovery/Recycling/Reclaiming Equipment, Procedures, and Leak Detection 5.4 Refrigerant Retrofits, Cylinder Handling, and Refrigerant Purity 5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice
6 Chapter 6: Refrigeration System Components and Accessories
6.1 Compressor Mechanics (Reciprocating, Scroll, Rotary, Screw) and Failures 6.2 Expansion Devices (TXV/TEV, Fixed Orifice, EEV) and Superheat Control 6.3 Condensers, Evaporators, Filter-Driers, Accumulators, Receivers, and Solenoids 6.4 Pressure Controls, Capacity Controls, and System Protection 6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice
7 Chapter 7: Gas Heating, Combustion Analysis, and Fuel Piping
7.1 Combustion Theory, Fuel Gases (Natural Gas vs LP), and Gas Burners 7.2 Gas Valves, Ignition Systems (Standing Pilot, Spark, HSI), and Safety Limit Controls 7.3 Flue Venting, Draft Principles, Combustion Analysis, and CO Safety 7.4 Fuel-Gas and Oil Piping, Vent System Selection and Sizing, and Installation Practice
8 Chapter 8: Electric Heating, Oil Heat, and Hydronics
8.1 Electric Heating Elements, Sequencers, Limit Switches, and kW Calculations 8.2 Oil Burners, Fuel Pumps, Nozzles, Ignition Electrodes, and Primary Controls 8.3 Hydronic Boilers, Circulator Pumps, Expansion Tanks, and Zone Controls 8.4 Combustion Air, Water Heaters, and Combustion Appliance Zone Testing
9 Chapter 9: Heat Pumps and Dual-Fuel Systems
9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation 9.2 Defrost Controls (Time-Temperature, Demand Defrost), Sensors, and Sequences 9.3 Balance Points, Auxiliary/Emergency Heat, and Dual-Fuel (Hybrid) Systems 9.4 Heat Pump Diagnostics, Refrigerant Flow, and Troubleshooting Procedures 9.5 Heat Pump Types, Cold-Climate Performance, and Sizing Approaches
10 Chapter 10: Air Distribution, IAQ, and System Commissioning
10.1 Airflow Fundamentals, CFM Measurement, External Static Pressure, and Fan Laws 10.2 Duct Sizing Principles, Supply/Return Distribution, Dampers, and Air Balancing 10.3 Indoor Air Quality, MERV Ratings, Electronic Cleaners, Humidification, and Dehumidification 10.4 Deep Vacuum Evacuation (Micron Gauge), Subcooling/Superheat Charging, and System Commissioning 10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance
11 Chapter 11: Psychrometrics, Airside Calculations, and Load Estimation
11.1 Reading the Psychrometric Chart: Properties and Plotting 11.2 The Eight Air-Conditioning Processes and the Process Triangle 11.3 Mixed Air, Ventilation, and Infiltration Calculations 11.4 Residential Heat Loss, Heat Gain, and Equipment Sizing
12 Chapter 12: Light Commercial Air Conditioning
12.1 Packaged Rooftop and Split Light-Commercial Systems 12.2 Water-Cooled Condensers, Cooling Towers, and Chilled-Water Systems 12.3 Economizers, Demand-Controlled Ventilation, and VAV Air Distribution 12.4 Light-Commercial Start-Up, Commissioning, and Troubleshooting
13 Chapter 13: Light Commercial Refrigeration
13.1 Temperature Ranges, Box Loads, and Refrigeration System Types 13.2 Evaporators, Defrost Methods, and Defrost Controls 13.3 Condensing Units, Parallel Racks, Oil Management, and Capacity Control 13.4 Refrigeration Control Valves and Automatic Pump-Down 13.5 Commercial Refrigeration Diagnostics and Ice Machines
14 Chapter 14: Ductless, Mini-Split, and VRF Systems
14.1 Mini-Split Architecture and Inverter-Driven Compressors 14.2 Multi-Zone and VRF Operation, Electronic Expansion Valves, and Controls 14.3 Ductless Installation, Evacuation, Charging, and Diagnostics
15 Chapter 15: Building Automation and Digital Controls
15.1 DDC Fundamentals, Control Loops, and Sequences of Operation 15.2 BAS Networks, Protocols, and NEC-Compliant Cabling 15.3 Building Automation Controllers: Supervisory, Field, and Room Devices 15.4 Digital Logic, Numbering Systems, and Controller Programming 15.5 Sensor Selection, Installation, and Input Point Configuration 15.6 Actuators, Output Devices, and VFD Integration 15.7 Commercial Prints, Equipment Schedules, and BAS Documentation
15.6 Actuators, Output Devices, and VFD Integration
Key Takeaways Explain This Topic AI
The task list names six output components for building automation: control valves, regulators, dampers, variable-speed drives, solid-state relays, and TRIACs.
Two-way control valves vary system flow and are required for variable-flow pumping, while three-way valves divert or mix and hold system flow roughly constant.
Valve authority is the fully-open valve pressure drop divided by the total circuit drop; below about 0.25 the valve does nearly all its work in the first fraction of its travel.
Opposed-blade dampers give near-linear modulating control, while parallel-blade dampers deflect the airstream and are better suited to two-position service.
A spring-return actuator drives to a defined position on power loss, and verifying that the fail position is safe for the application is a required commissioning check.
Last updated: August 2026
15.6 Actuators, Output Devices, and VFD Integration
The Actuator Installation and Applications block of the Competency and Task List requires identifying and describing the proper application of control valves, regulators, dampers, variable-speed drives, solid-state relays, and TRIACs ; wiring actuators to unit controllers per NEC requirements ; addressing points for various output devices ; configuring outputs to unit controllers ; and configuring a VFD to operate with a BAS network .
Outputs are where control becomes mechanical work, and they are where most "the control system is broken" calls actually live. The workstation will cheerfully report a damper at 100% open while the blade has not moved.
1. Output Signal Types
Signal How it works Where used
Binary (two-position) Relay contact energizes or de-energizes the device Start/stop, enable, two-position dampers and valves
- 0–10 VDC Analog voltage commands actuator position The BAS modulating standard
- 4–20 mA Analog current commands position Long runs, noisy environments, industrial devices
Floating (tri-state) Two binary outputs — one drives open, one drives closed, neither holds Common on damper and valve actuators; no position feedback unless a separate signal is provided
PWM (pulse-width modulation) Position encoded as pulse duration Some proprietary actuators; also SCR-driven electric heat
Network command The value is written to a protocol object VFDs, smart valves, packaged equipment
Floating control has a specific field consequence. Because the controller has no idea where the actuator actually is, a floating loop periodically drives fully closed to re-establish a known reference — a normal behavior that reads as a fault to someone unfamiliar with it. If floating linkage slips, the controller's internal position estimate and the real blade position diverge with nothing to correct them.
2. Control Valves
Two-way versus three-way is the fundamental application decision.
- Two-way Three-way
- Effect on system flow Varies — closing reduces system flow Constant — flow is diverted, not stopped
- Piping Straight through the coil Adds a bypass around the coil
- Pumping Required for variable-flow systems with a VFD on the pump Suits constant-flow systems
- Energy Pump power falls with flow (cube law) Pump runs at full flow regardless of load
- Sub-types — Mixing (two inlets, one outlet) and diverting (one inlet, two outlets) — not interchangeable
Installing a mixing valve where a diverting valve belongs, or vice versa, causes the plug to chatter and wear because the flow tries to force it off its seat.
Sizing by Cv, not by pipe size. A valve's flow coefficient Cv is the flow in gpm of 60°F water that produces a 1 psi pressure drop: C v = Q Δ P C_v = \frac{Q}{\sqrt{\Delta P}} C v = Δ P Q
For a coil needing 24 gpm at a 9 psi valve drop: C v = 24 9 = 24 3 = 8.0 C_v = \frac{24}{\sqrt{9}} = \frac{24}{3} = 8.0 C v = 9 24 = 3 24 = 8.0
A valve is selected to match the required Cv — which is very often smaller than the pipe . Selecting a valve to match line size is the classic oversizing error.
Valve authority is why oversizing ruins control: β = Δ P valve, fully open Δ P valve, fully open + Δ P rest of circuit \beta = \frac{\Delta P_{\text{valve, fully open}}}{\Delta P_{\text{valve, fully open}} + \Delta P_{\text{rest of circuit}}} β = Δ P valve, fully open + Δ P rest of circuit Δ P valve, fully open
Authority of roughly 0.5 or higher gives good control; below about 0.25 the valve does nearly all of its flow change within the first fraction of its travel and behaves like an on/off device with a long useless tail. The symptom in the field is a coil that overshoots and hunts and a valve that lives between 5% and 20% open.
Characteristics: an equal-percentage plug pairs with a hot- or chilled-water coil, because the coil's own output is non-linear (the first gpm does most of the heat transfer) and the two non-linearities cancel to give near-linear control. A linear plug suits applications where flow itself is the controlled variable.
Regulators — the other device the task list names — hold a downstream condition without a controller. Pressure-reducing valves, pressure-independent control valves (PICVs, which combine a differential-pressure regulator with a control valve so that flow depends only on position, not on system pressure), and gas pressure regulators (Section 7.2) are all self-contained mechanical control.
3. Dampers
Blade arrangement Behavior Best use
Parallel blade All blades rotate the same direction; the airstream is deflected to one side as the damper closes Two-position service; poor modulating control
Opposed blade Adjacent blades rotate opposite directions; the opening stays centered Modulating service — mixing boxes, economizers, VAV
An economizer built with parallel-blade outdoor and return dampers throws outdoor air against one wall of the mixing plenum, which produces exactly the stratification that defeats a single-point mixed-air sensor (Section 15.5) and freezes coils.
Leakage class matters on any damper that closes against outdoor air. A low-leakage damper with blade and jamb seals is required on outdoor-air intakes in cold climates and on isolation dampers; a standard damper leaks enough at design pressure to freeze a coil overnight.
Actuator torque sizing is done from damper area and the required seal torque, in inch-pounds . A rule of thumb of roughly 5 in-lb per square foot of damper area is a starting point for a standard damper, with more for low-leakage seals and higher differential pressure; the damper manufacturer's torque table is the authority. An undersized actuator stalls near the closed position, precisely where the seal load peaks, so the damper never fully closes and the fault appears only in cold weather.
4. Solid-State Relays and TRIACs
A TRIAC (TRIode for Alternating Current) is a bidirectional semiconductor switch that conducts in both half-cycles of AC. It is the output stage of most BAS binary outputs and of solid-state relays.
- Electromechanical relay Solid-state relay / TRIAC
- Switching Moving contacts Semiconductor, no moving parts
- Life Limited by contact erosion Very long; unaffected by cycle count
- Noise Audible click; contact bounce Silent
- Off-state True open circuit Small leakage current still flows
- Heat Negligible Dissipates heat; may need a heat sink
- Load type AC or DC AC only for a TRIAC
Two field problems the exam likes:
A TRIAC output sinks current. It is not a dry contact. It switches the common/ground side of a 24 VAC load, which means the load must be wired to the transformer hot on one side and to the TRIAC output on the other. Wiring it like a dry contact — expecting to pass power through it from a separate source — produces a device that never energizes or a controller output that fails.
Leakage current in the off state. A TRIAC never fully stops conducting. That residual milliamp or two is harmless to a contactor coil but is enough to keep a sensitive electronic relay, an LED indicator, or a small solid-state load partially energized. The symptom is a device that will not turn off. The remedy is a bleed resistor across the load, or an interposing electromechanical relay.
Interposing relays are the general answer whenever the controller output cannot directly handle the load: the output switches a small pilot relay, and the pilot relay's contacts switch the real load. This isolates the controller from inductive kickback and from line voltage.
5. VFD Integration with a BAS Network
"Configuring a VFD to operate with a BAS network" is a named task-list competency. There are two ways to command a drive, and the parameter set differs.
- Hardwired analog Network command
- Speed reference 0–10 VDC or 4–20 mA to the drive's analog input Written to a protocol register/object
- Start/stop Dry contact to the drive's run input Network command word
Feedback available Whatever is separately wired: run status, fault contact Speed, current, power, torque, fault code, run hours, energy
- Wiring More conductors One twisted pair shared with the rest of the bus
- Failure behavior Drive keeps its last analog reference Requires a configured communication-loss action
Parameters that must be set for network control:
Command source / reference source set to the network (not keypad, not terminal strip). Leaving the reference at "terminal" while writing speed over the network is the most common reason a drive ignores the BAS.
Protocol, address, baud rate, and parity matched to the bus.
Communication-loss action and timeout — what the drive does when the network goes quiet. "Fault and stop" is correct for some equipment and unacceptable for others; a supply fan serving a critical space usually should hold last speed or run at a fixed backup speed instead.
Minimum and maximum speed limits set in the drive, not only in the BAS. A pump or fan driven below its minimum safe speed can overheat its motor or, on a pump, run below the point at which it develops any head.
Acceleration and deceleration ramps appropriate to the load.
Wiring practice for drives: VFD output cable is an aggressive noise source. Keep it in its own raceway, use shielded VFD cable where the manufacturer specifies it, and never run control or sensor wiring parallel to drive output conductors for any distance. Most "the sensor reads erratically" calls in a mechanical room end at a control pair zip-tied to a drive output conduit.
6. Commissioning Outputs
Output configuration mirrors input configuration (Section 15.5): terminal assignment, output type, range and scaling, point name and address, and failure handling. But outputs get one thing inputs do not — a physical verification .
Confirm the fail position before energizing. A spring-return actuator drives to a defined position on power loss. Verify it is the safe one: an outdoor-air damper that fails open in a cold climate will freeze a hydronic coil; a heating valve that fails open protects the coil but can cook the space; a chilled-water valve that fails closed protects nothing if the fan keeps running.
Command 0%, 50%, and 100% and physically watch the device. Do not accept the workstation's report. Loose linkage, a slipping shaft coupler, a stripped set screw, and a jammed blade are all invisible from the graphics, and the workstation will report the commanded position, not the actual one.
Verify direction of action. Direct-acting versus reverse-acting is a configuration setting, and reversing it produces a loop that drives to full output in exactly the wrong direction — a room that gets colder the harder the system tries to heat it.
Stroke the full range and check for stall. An undersized actuator commonly reaches 90% of travel and stalls on the seal load.
Check position feedback against reality where feedback exists, and add an end switch where the sequence depends on proven position.
Record the readings. Commissioning documentation that says "verified" without numbers is worth nothing to the next technician.