Study guide

15.5 Sensor Selection, Installation, and Input Point Configuration

HVAC Excellence Certification Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction, Safety, Tools, and Diagnostic Method

1.1 HVAC Excellence Certification, Industry Codes, and Standards 1.2 Electrical Safety, PPE, Lockout/Tagout, and Hazard Communication 1.3 Multimeters, Manifold Gauges, Micron Gauges, and Diagnostic Instruments 1.4 HVACR Mathematics, Unit Conversions, and Efficiency Ratings 1.5 OSHA Standards, Fall Protection, Rigging, and Confined Spaces 1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs 1.7 Systematic Troubleshooting: Data Plates, Manufacturer Literature, and Diagnostic Method

2 Chapter 2: Electrical Fundamentals and Circuit Theory

2.1 Voltage, Current, Resistance, and Ohm's Law Calculations 2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations 2.3 AC Fundamentals, Single-Phase vs Three-Phase Power, and Control Transformers 2.4 Conductors, Insulators, Wire Sizing, Voltage Drop, and NEC Ampacity

3 Chapter 3: Electrical Components, Motors, and Schematics

3.1 Contactors, Relays, Switches, Overload Protection, and Thermostats 3.2 HVAC Motors (PSC, CSIR, CSCR, ECM, 3-Phase) and Run/Start Capacitors 3.3 Interpreting Ladder Diagrams, Schematics, and Point-to-Point Wiring 3.4 Motor Testing, Insulation Resistance, Bearings, and Belt Drives

4 Chapter 4: Thermodynamics and the Refrigeration Cycle

4.1 Heat Transfer, Temperature Scales, BTUs, Sensible vs Latent Heat, and Enthalpy 4.2 The Four Vapor-Compression Cycle Stages (Compression, Condensation, Expansion, Evaporation) 4.3 P-T Charts, Saturated Conditions, Target Superheat, and Subcooling Calculations 4.4 Pressure–Enthalpy Diagrams, Compression Ratio, and Cycle Analysis

5 Chapter 5: Refrigerants, Environmental Regulations, and Recovery

5.1 Refrigerant Types (CFC, HCFC, HFC, HFO, HC) and ASHRAE Safety Groups (A1, A2L, A3) 5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards 5.3 Recovery/Recycling/Reclaiming Equipment, Procedures, and Leak Detection 5.4 Refrigerant Retrofits, Cylinder Handling, and Refrigerant Purity 5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice

6 Chapter 6: Refrigeration System Components and Accessories

6.1 Compressor Mechanics (Reciprocating, Scroll, Rotary, Screw) and Failures 6.2 Expansion Devices (TXV/TEV, Fixed Orifice, EEV) and Superheat Control 6.3 Condensers, Evaporators, Filter-Driers, Accumulators, Receivers, and Solenoids 6.4 Pressure Controls, Capacity Controls, and System Protection 6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice

7 Chapter 7: Gas Heating, Combustion Analysis, and Fuel Piping

7.1 Combustion Theory, Fuel Gases (Natural Gas vs LP), and Gas Burners 7.2 Gas Valves, Ignition Systems (Standing Pilot, Spark, HSI), and Safety Limit Controls 7.3 Flue Venting, Draft Principles, Combustion Analysis, and CO Safety 7.4 Fuel-Gas and Oil Piping, Vent System Selection and Sizing, and Installation Practice

8 Chapter 8: Electric Heating, Oil Heat, and Hydronics

8.1 Electric Heating Elements, Sequencers, Limit Switches, and kW Calculations 8.2 Oil Burners, Fuel Pumps, Nozzles, Ignition Electrodes, and Primary Controls 8.3 Hydronic Boilers, Circulator Pumps, Expansion Tanks, and Zone Controls 8.4 Combustion Air, Water Heaters, and Combustion Appliance Zone Testing

9 Chapter 9: Heat Pumps and Dual-Fuel Systems

9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation 9.2 Defrost Controls (Time-Temperature, Demand Defrost), Sensors, and Sequences 9.3 Balance Points, Auxiliary/Emergency Heat, and Dual-Fuel (Hybrid) Systems 9.4 Heat Pump Diagnostics, Refrigerant Flow, and Troubleshooting Procedures 9.5 Heat Pump Types, Cold-Climate Performance, and Sizing Approaches

10 Chapter 10: Air Distribution, IAQ, and System Commissioning

10.1 Airflow Fundamentals, CFM Measurement, External Static Pressure, and Fan Laws 10.2 Duct Sizing Principles, Supply/Return Distribution, Dampers, and Air Balancing 10.3 Indoor Air Quality, MERV Ratings, Electronic Cleaners, Humidification, and Dehumidification 10.4 Deep Vacuum Evacuation (Micron Gauge), Subcooling/Superheat Charging, and System Commissioning 10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance

11 Chapter 11: Psychrometrics, Airside Calculations, and Load Estimation

11.1 Reading the Psychrometric Chart: Properties and Plotting 11.2 The Eight Air-Conditioning Processes and the Process Triangle 11.3 Mixed Air, Ventilation, and Infiltration Calculations 11.4 Residential Heat Loss, Heat Gain, and Equipment Sizing

12 Chapter 12: Light Commercial Air Conditioning

12.1 Packaged Rooftop and Split Light-Commercial Systems 12.2 Water-Cooled Condensers, Cooling Towers, and Chilled-Water Systems 12.3 Economizers, Demand-Controlled Ventilation, and VAV Air Distribution 12.4 Light-Commercial Start-Up, Commissioning, and Troubleshooting

13 Chapter 13: Light Commercial Refrigeration

13.1 Temperature Ranges, Box Loads, and Refrigeration System Types 13.2 Evaporators, Defrost Methods, and Defrost Controls 13.3 Condensing Units, Parallel Racks, Oil Management, and Capacity Control 13.4 Refrigeration Control Valves and Automatic Pump-Down 13.5 Commercial Refrigeration Diagnostics and Ice Machines

14 Chapter 14: Ductless, Mini-Split, and VRF Systems

14.1 Mini-Split Architecture and Inverter-Driven Compressors 14.2 Multi-Zone and VRF Operation, Electronic Expansion Valves, and Controls 14.3 Ductless Installation, Evacuation, Charging, and Diagnostics

15 Chapter 15: Building Automation and Digital Controls

15.1 DDC Fundamentals, Control Loops, and Sequences of Operation 15.2 BAS Networks, Protocols, and NEC-Compliant Cabling 15.3 Building Automation Controllers: Supervisory, Field, and Room Devices 15.4 Digital Logic, Numbering Systems, and Controller Programming 15.5 Sensor Selection, Installation, and Input Point Configuration 15.6 Actuators, Output Devices, and VFD Integration 15.7 Commercial Prints, Equipment Schedules, and BAS Documentation

15.5 Sensor Selection, Installation, and Input Point Configuration

Key Takeaways Explain This Topic AI

The Competency and Task List names nine sensed quantities for building automation: temperature, humidity, pressure, velocity, level, proximity, CO2, motion, and photoelectric.

A 10 kilohm NTC thermistor is the building-automation standard temperature sensor, while platinum RTDs are used where wide-range linearity and stability matter.

Sensor location determines validity: a space sensor in sunlight or on an exterior wall reports something other than the space condition, no matter how accurate the device is.

A 4-20 mA transmitter has a live zero, so a broken conductor reads 0 mA and can be flagged as a fault, while an open 0-10 VDC circuit reads 0 V and is indistinguishable from a real zero.

Averaging elements are required across large duct cross-sections and mixed-air plenums where stratification makes any single-point reading unrepresentative.

Last updated: August 2026

15.5 Sensor Selection, Installation, and Input Point Configuration

The Building Automation competency block on Sensor Installation and Applications requires four things: identifying the types of sensors that measure temperature, humidity, pressure, velocity, level, proximity, CO₂, motion, and photoelectric signals; describing the proper application of each; wiring sensors to unit controllers per NEC requirements ; addressing points for various input sensor types; and configuring inputs to unit controllers.

A control system is only as good as the numbers it is fed. A drifted or badly located sensor makes a perfectly written sequence behave badly, and the workstation will report the wrong value with total confidence. This section is about getting the number right before blaming the logic.

1. Sensing Technologies by Measured Quantity

Measured Technology Typical BAS device Notes

Temperature Thermistor (10 kΩ NTC is the BAS standard), RTD (100 Ω or 1,000 Ω platinum), thermocouple Space, duct, immersion, averaging, outdoor-air sensors Thermistors are sensitive, cheap, and non-linear (linearized in the controller). RTDs are linear and stable over wide ranges. Thermocouples belong to combustion and high-temperature work (Section 7.2), not BAS space sensing

Humidity Capacitive polymer thin film Space and duct RH transmitters Drifts with time and contamination. Plan on periodic calibration or scheduled replacement; a five-year-old uncalibrated RH sensor is not trustworthy

Pressure (static / differential) Piezoresistive or capacitive transducer Duct static, building static, filter differential, water differential Range selection matters — a 0–5 in. w.c. transducer used for a 0.05 in. w.c. building-pressure measurement has no usable resolution

Velocity / flow Averaging pitot array , hot-wire anemometer, vortex shedding, magnetic (water), turbine VAV box flow ring, AHU airflow station, chilled-water flow meter A VAV flow ring is an averaging pitot array; its accuracy depends on straight duct upstream

Level Float switch, capacitive, ultrasonic, differential pressure Condensate sump, tank, cooling-tower basin Float switches are binary; capacitive and ultrasonic give continuous level

Proximity / position Inductive, magnetic reed, mechanical limit switch Damper end switches, valve position feedback, access-door interlocks Usually a binary input confirming a device actually moved

CO₂ NDIR (non-dispersive infrared) Space or return-duct CO₂ transmitter The basis of demand-controlled ventilation (Section 12.3). Requires calibration or an automatic background calibration routine

Motion / occupancy Passive infrared (PIR), ultrasonic, dual technology Ceiling or wall occupancy sensors PIR needs line of sight and detects movement, not presence — a still occupant can time out

Photoelectric Photodiode / photoresistor, through-beam or reflective Daylight harvesting, ice-machine bin level, flame detection, belt-break detection Lens contamination is the dominant failure mode

2. Input Signal Types and How the Controller Reads Them

Sensors reach a controller as one of four input classes, and the controller's input must be configured to match .

Input class Signal Controller setup Typical use

Resistive analog Ω that varies with the measured value Select the sensor curve (10 kΩ Type II, Type III, 1 kΩ Pt) Thermistors, RTDs

Voltage analog 0–5 or 0–10 VDC Set range and scale to engineering units Pressure, RH, CO₂ transmitters

Current analog 4–20 mA Requires a loop resistor (often a jumper on the input); set scaling Long runs, electrically noisy environments

Binary Dry contact, open/closed Set normal state (N.O. or N.C.) Status, alarm, proximity, float switch

Scaling is a separate step from wiring, and skipping it is the most common commissioning defect. A 0–10 VDC pressure transmitter with a 0–5 in. w.c. range wired to an input that is still scaled 0–100 will read "53" when duct static is 2.65 in. w.c. Everything is wired correctly; the number is meaningless. Configure the input with the transmitter's range from its label , not from memory or from the last job.

4–20 mA and the live zero. Because the loop is a current loop, series resistance in a long conductor does not change the current, so distance does not shift the reading the way it does on 0–10 VDC. And because the bottom of the range is 4 mA, not 0 , a broken conductor produces 0 mA — a value outside the valid range that the controller can flag as an unreliable point. An open 0–10 VDC circuit reads 0 V, which is indistinguishable from a legitimate zero. This is the reason 4–20 mA survives in critical and long-run applications.

3. Location: The Rule That Beats Accuracy

A ±0.2°F sensor in the wrong place is worse than a ±1.0°F sensor in the right one, because the accurate device makes a wrong number credible.

Space sensors — where not to mount:

  • On an exterior wall , where conduction through the wall biases the reading with outdoor temperature
  • In direct sunlight at any hour of the day
  • Directly above or beside a heat source — a copier, a monitor, a coffee maker, a light fixture
  • In the discharge path of a supply diffuser , where it reads supply air rather than space air
  • Behind a door, inside a closet, or in a corner with no air movement

On a wall cavity that is open to a chase or to unconditioned space — stuffing the box with insulation stops the chimney effect that otherwise pulls attic or crawlspace air across the sensing element

Duct sensors:

Locate in a well-mixed section , at least several duct diameters downstream of a coil, a mixing box, or a branch takeoff.

Immediately downstream of a coil or a mixing plenum, temperature stratification of 15–20°F across the cross-section is normal, so a single-point probe reports whatever stratum it happens to sit in.

Averaging elements — a long serpentine capillary or several sensing elements in series, strung across the duct — are the correct answer there. The task list's mixed-air and economizer sequences depend on them: an economizer controlled from a single-point mixed-air probe will hunt or freeze a coil.

Seal the penetration and support the probe so it cannot vibrate against sheet metal.

Outdoor-air sensors: north side, shaded, out of direct sun and away from exhaust discharge, relief hoods, and condenser discharge. An outdoor sensor mounted above a rooftop condenser reads the condenser, and every reset and economizer decision downstream is then wrong.

CO₂ sensors: in the breathing zone (roughly 3–6 ft above the floor) or in the return path serving the zone, away from the direct throw of a diffuser and away from where occupants exhale onto the device.

4. Wiring per NEC Requirements

Every wiring task in this block ends with "per NEC requirements," and the rules from Section 15.2 apply to sensor wiring specifically:

Sensor wiring is almost always Class 2, power-limited under Article 725 .

Never share a raceway, cable, or enclosure with line-voltage conductors unless separated by a permanent barrier. Running a thermistor pair alongside a VFD output is the fastest way to build an unstable input.

Use plenum-rated cable (CMP) in ducts, plenums, and ceiling cavities used as return-air plenums.

Use shielded, twisted pair for analog inputs in electrically noisy areas, and ground the shield at the controller end only — grounding both ends creates a ground loop that injects the noise you were trying to reject.

Support the cable on J-hooks or in tray at code intervals. Cable draped on ceiling grid or on piping is a citable violation.

Observe conductor gauge and length . On a 10 kΩ thermistor, the wire's own resistance adds directly to the sensed resistance; on a long run of small conductor this shows up as a fixed offset the technician then "fixes" with a bias, hiding the real problem.

Label both ends of every conductor.

Two-wire, three-wire, and four-wire transmitters are not interchangeable. A two-wire (loop-powered) 4–20 mA transmitter draws its power from the loop; a three-wire device needs separate power and a shared common; a four-wire device has isolated power and signal. Wiring a three-wire transmitter as though it were loop-powered gives a dead input, and the sensor is usually blamed.

5. Addressing and Configuring Inputs

The task list names "addressing points for various input sensor types" and "configuring inputs to unit controllers" as distinct competencies.

A complete input configuration has six parts:

Terminal assignment — which physical input the sensor lands on (AI-1, UI-4, BI-2)

Input type — resistive, voltage, current, or dry contact, often set by a jumper or DIP switch and in software; both must agree

  • Sensor curve or range — 10 kΩ Type III, 0–10 V, 4–20 mA
  • Engineering-unit scaling — the transmitter's range mapped to the displayed value and units

Point name and address — following the site convention ( AHU2_MAT , not AI3 ), with the network address recorded in the address schema (Section 15.7)

Alarm limits and reliability handling — what the controller does when the value goes out of range or the point goes unreliable

Configuring a point on a networked sensor bus adds an address step: the room operator or smart sensor carries its own address, set by DIP switch, rotary switch, or software, and it must be unique on that bus.

6. Verifying a Sensor Before Replacing It

The discipline that separates a technician from a parts-swapper:

Compare to a calibrated reference. Put a known-good instrument next to the sensor and compare readings at the same moment. A sling psychrometer or calibrated digital psychrometer for space conditions; a calibrated thermometer for duct and immersion.

Measure the raw signal at the sensor and again at the controller terminals. If the two disagree, the fault is in the wiring, not the sensor. If they agree but the workstation shows something else, the fault is in the scaling or the curve selection.

Check the thermistor against its resistance table. A 10 kΩ Type II NTC thermistor reads 10,000 Ω at 77°F (25°C) ; resistance rises as temperature falls. Measure resistance with the sensor disconnected from the controller and compare to the manufacturer's temperature–resistance table for that curve.

Trend the point. A sensor that reads a plausible value but holds it unchanged for hours is failed. A single spot reading cannot reveal that; a trend reveals it immediately. This is the diagnostic the task list's "trending" competency exists for.

Check the mounting before the device. If the reading is plausible but always biased one direction, suspect location — sun, a heat source, an unsealed wall cavity, stratification — before condemning the sensor.

Then, and only then, replace — and after replacing, verify the new device against the reference rather than assuming a new part is a correct part.