Study guide
14.3 Ductless Installation, Evacuation, Charging, and Diagnostics
HVAC Excellence Certification Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction, Safety, Tools, and Diagnostic Method
1.1 HVAC Excellence Certification, Industry Codes, and Standards 1.2 Electrical Safety, PPE, Lockout/Tagout, and Hazard Communication 1.3 Multimeters, Manifold Gauges, Micron Gauges, and Diagnostic Instruments 1.4 HVACR Mathematics, Unit Conversions, and Efficiency Ratings 1.5 OSHA Standards, Fall Protection, Rigging, and Confined Spaces 1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs 1.7 Systematic Troubleshooting: Data Plates, Manufacturer Literature, and Diagnostic Method
2 Chapter 2: Electrical Fundamentals and Circuit Theory
2.1 Voltage, Current, Resistance, and Ohm's Law Calculations 2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations 2.3 AC Fundamentals, Single-Phase vs Three-Phase Power, and Control Transformers 2.4 Conductors, Insulators, Wire Sizing, Voltage Drop, and NEC Ampacity
3 Chapter 3: Electrical Components, Motors, and Schematics
3.1 Contactors, Relays, Switches, Overload Protection, and Thermostats 3.2 HVAC Motors (PSC, CSIR, CSCR, ECM, 3-Phase) and Run/Start Capacitors 3.3 Interpreting Ladder Diagrams, Schematics, and Point-to-Point Wiring 3.4 Motor Testing, Insulation Resistance, Bearings, and Belt Drives
4 Chapter 4: Thermodynamics and the Refrigeration Cycle
4.1 Heat Transfer, Temperature Scales, BTUs, Sensible vs Latent Heat, and Enthalpy 4.2 The Four Vapor-Compression Cycle Stages (Compression, Condensation, Expansion, Evaporation) 4.3 P-T Charts, Saturated Conditions, Target Superheat, and Subcooling Calculations 4.4 Pressure–Enthalpy Diagrams, Compression Ratio, and Cycle Analysis
5 Chapter 5: Refrigerants, Environmental Regulations, and Recovery
5.1 Refrigerant Types (CFC, HCFC, HFC, HFO, HC) and ASHRAE Safety Groups (A1, A2L, A3) 5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards 5.3 Recovery/Recycling/Reclaiming Equipment, Procedures, and Leak Detection 5.4 Refrigerant Retrofits, Cylinder Handling, and Refrigerant Purity 5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice
6 Chapter 6: Refrigeration System Components and Accessories
6.1 Compressor Mechanics (Reciprocating, Scroll, Rotary, Screw) and Failures 6.2 Expansion Devices (TXV/TEV, Fixed Orifice, EEV) and Superheat Control 6.3 Condensers, Evaporators, Filter-Driers, Accumulators, Receivers, and Solenoids 6.4 Pressure Controls, Capacity Controls, and System Protection 6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice
7 Chapter 7: Gas Heating, Combustion Analysis, and Fuel Piping
7.1 Combustion Theory, Fuel Gases (Natural Gas vs LP), and Gas Burners 7.2 Gas Valves, Ignition Systems (Standing Pilot, Spark, HSI), and Safety Limit Controls 7.3 Flue Venting, Draft Principles, Combustion Analysis, and CO Safety 7.4 Fuel-Gas and Oil Piping, Vent System Selection and Sizing, and Installation Practice
8 Chapter 8: Electric Heating, Oil Heat, and Hydronics
8.1 Electric Heating Elements, Sequencers, Limit Switches, and kW Calculations 8.2 Oil Burners, Fuel Pumps, Nozzles, Ignition Electrodes, and Primary Controls 8.3 Hydronic Boilers, Circulator Pumps, Expansion Tanks, and Zone Controls 8.4 Combustion Air, Water Heaters, and Combustion Appliance Zone Testing
9 Chapter 9: Heat Pumps and Dual-Fuel Systems
9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation 9.2 Defrost Controls (Time-Temperature, Demand Defrost), Sensors, and Sequences 9.3 Balance Points, Auxiliary/Emergency Heat, and Dual-Fuel (Hybrid) Systems 9.4 Heat Pump Diagnostics, Refrigerant Flow, and Troubleshooting Procedures 9.5 Heat Pump Types, Cold-Climate Performance, and Sizing Approaches
10 Chapter 10: Air Distribution, IAQ, and System Commissioning
10.1 Airflow Fundamentals, CFM Measurement, External Static Pressure, and Fan Laws 10.2 Duct Sizing Principles, Supply/Return Distribution, Dampers, and Air Balancing 10.3 Indoor Air Quality, MERV Ratings, Electronic Cleaners, Humidification, and Dehumidification 10.4 Deep Vacuum Evacuation (Micron Gauge), Subcooling/Superheat Charging, and System Commissioning 10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance
11 Chapter 11: Psychrometrics, Airside Calculations, and Load Estimation
11.1 Reading the Psychrometric Chart: Properties and Plotting 11.2 The Eight Air-Conditioning Processes and the Process Triangle 11.3 Mixed Air, Ventilation, and Infiltration Calculations 11.4 Residential Heat Loss, Heat Gain, and Equipment Sizing
12 Chapter 12: Light Commercial Air Conditioning
12.1 Packaged Rooftop and Split Light-Commercial Systems 12.2 Water-Cooled Condensers, Cooling Towers, and Chilled-Water Systems 12.3 Economizers, Demand-Controlled Ventilation, and VAV Air Distribution 12.4 Light-Commercial Start-Up, Commissioning, and Troubleshooting
13 Chapter 13: Light Commercial Refrigeration
13.1 Temperature Ranges, Box Loads, and Refrigeration System Types 13.2 Evaporators, Defrost Methods, and Defrost Controls 13.3 Condensing Units, Parallel Racks, Oil Management, and Capacity Control 13.4 Refrigeration Control Valves and Automatic Pump-Down 13.5 Commercial Refrigeration Diagnostics and Ice Machines
14 Chapter 14: Ductless, Mini-Split, and VRF Systems
14.1 Mini-Split Architecture and Inverter-Driven Compressors 14.2 Multi-Zone and VRF Operation, Electronic Expansion Valves, and Controls 14.3 Ductless Installation, Evacuation, Charging, and Diagnostics
15 Chapter 15: Building Automation and Digital Controls
15.1 DDC Fundamentals, Control Loops, and Sequences of Operation 15.2 BAS Networks, Protocols, and NEC-Compliant Cabling 15.3 Building Automation Controllers: Supervisory, Field, and Room Devices 15.4 Digital Logic, Numbering Systems, and Controller Programming 15.5 Sensor Selection, Installation, and Input Point Configuration 15.6 Actuators, Output Devices, and VFD Integration 15.7 Commercial Prints, Equipment Schedules, and BAS Documentation
14.3 Ductless Installation, Evacuation, Charging, and Diagnostics
Key Takeaways Explain This Topic AI
Flare joints are the most common leak point on a mini-split, and each flare must be made with the nut installed first, lubricated with the system oil, and torqued to the manufacturer's specification.
Mini-splits must be evacuated through both service ports with the valve cores removed, because the small port and long line set make single-port evacuation impractically slow.
Never use the outdoor unit's factory charge to purge air from the line set; recover, evacuate to 500 microns, and confirm with a decay test before opening the service valves.
Additional refrigerant is required when the line set exceeds the manufacturer's pre-charged length, at a published rate in ounces per foot of the liquid line.
Manufacturer fault codes displayed by LED blink patterns or on the indoor display are the primary diagnostic tool and should be read before any component is removed.
Last updated: August 2026
14.3 Ductless Installation, Evacuation, Charging, and Diagnostics
The Mini-Splits sheet requires demonstrating proficiency in refrigerant piping, soldering and brazing, flaring , system evacuation (single and triple), connecting gauge manifolds, vacuum pumps, micron gauges and recovery units, obtaining and interpreting gauge readings, calculating superheat and subcooling, purging with nitrogen, installing indoor and outdoor units, running a condensate removal line, and replacing every major component.
Ductless systems fail for installation reasons far more often than for manufacturing reasons, and the failures cluster in three places: flares, evacuation, and charge .
- 1. Mounting and Line Set Routing
- Outdoor unit
Mount on a pad, bracket, or stand that keeps the unit above expected snow depth and above ground splash. In heating operation the outdoor coil is the evaporator and produces defrost condensate that must drain away and not pool and refreeze under the unit.
Provide manufacturer-specified clearances — typically 4–12 inches at the back, 20+ inches at the service side, and unobstructed discharge.
Use vibration isolation pads. Ductless outdoor units are quiet in the air and loud through structure.
Do not locate under a roof drip line, near a bedroom window, or where discharge air recirculates off a wall.
Indoor unit
Mount level, or with a very slight slope toward the drain . A wall cassette mounted with the drain end high will overflow into the room.
Keep clear of heat sources, direct sun, and airflow obstructions, and leave the return path at the top of the unit unobstructed.
Mount on a structural member; the wall plate must not flex.
Wall penetration
Drill with a slight downward slope to the outside so the sleeve drains and rain does not track in.
Use a wall sleeve and seal both ends. An unsealed penetration is an air leak, a pest entry, and a source of condensation inside the wall cavity.
Route the drain hose below the refrigerant lines and communication cable inside the sleeve, and never let it kink.
Line set
Keep bends generous — most manufacturers specify a minimum bend radius (often about 4 inches) and a maximum number of bends. A kinked line set is a permanent restriction.
Do not stretch pre-flared line sets or reuse existing line sets from an R-410A system for A2L equipment without confirming compatibility, cleanliness, and pressure rating.
Insulate both lines separately over their full length, including inside the wall sleeve. On a heat pump the liquid line runs hot in cooling and cold in heating.
Support and secure the line set at code intervals; UV-rated tape or a line-hide channel protects insulation outdoors.
2. Flare Joints
Section 6.5 covers technique. Three points bear repeating because they cause most ductless leaks:
The nut goes on before the flare. Every time.
Torque to the manufacturer's value with a torque wrench , backing up the fitting with a second wrench. Typical published values are roughly 10–12 ft-lb for 1/4" , 25–27 ft-lb for 3/8" , and 35–40 ft-lb for 1/2" , but use the value in the installation manual for the specific unit. Under-torqued flares leak immediately; over-torqued flares split the copper and leak in six months.
A drop of the system's own oil (POE on HFC/HFO equipment) on the flare face before assembly produces a better seal and lets the nut reach proper torque without galling.
Pressure test before evacuating. Nitrogen-test the line set and indoor unit at the manufacturer's specified pressure, with the outdoor service valves still closed, and hold it long enough to be meaningful with a recorded temperature (Section 6.5). Finding a bad flare with nitrogen costs ten minutes. Finding it after charging costs a recovery, a new charge, and a callback.
3. Evacuation
The problem: a mini-split has a single small 5/16" service port on the suction service valve, a long narrow line set, and an indoor coil with small tubes. Pulling a proper vacuum through one Schrader core is impractically slow, and the resulting shallow vacuum leaves moisture that will react with POE oil to form acid (Section 5.4).
The procedure:
Remove the Schrader valve cores using a valve core removal tool , which lets you extract the core under pressure and reinstall it without losing the vacuum.
Connect to both service ports where the equipment provides them, using large-diameter (3/8" or larger) evacuation hoses rather than standard 1/4" charging hoses.
Connect the micron gauge at the system , as far from the pump as practical — never at the pump, where it will read the pump's own vacuum rather than the system's.
Pull to 500 microns or lower .
Isolate the pump and perform a decay test. A rise that stabilizes below roughly 1,000 microns and holds indicates a dry, tight system. A rise that continues past 1,500–2,000 microns without leveling indicates a leak. A rise that levels off around 1,000–1,500 microns typically indicates remaining moisture — keep pulling, and consider warming the system or breaking the vacuum with dry nitrogen and re-evacuating ( triple evacuation ).
Reinstall the cores and only then open the service valves.
Do not purge with refrigerant. Cracking the outdoor service valve to blow air out of the line set is both a violation of the venting prohibition (Section 5.2) and a guarantee that moisture and non-condensables remain. It is one of the most common bad habits in ductless installation.
Open the service valves fully with the correct hex key, then cap them . The caps are the primary seal — the valve stem packing is secondary — and an uncapped service port is a slow leak.
4. Charge
Most single-zone mini-splits ship pre-charged for a specific line-set length , commonly 15, 25, or 50 feet depending on the model.
If the line set is at or below the pre-charged length , no refrigerant is added. Some manufacturers specify removing refrigerant for very short runs on larger systems; check the manual.
If the line set is longer , add the published rate — typically expressed in ounces per foot of liquid line beyond the pre-charged length (commonly around 0.2–0.4 oz/ft on residential equipment).
Weigh the addition in. Record the total charge on the unit label along with the line-set length. On a system whose EEV is continuously modulating and whose compressor frequency varies, superheat and subcooling do not provide a reliable total-charge verification the way they do on a fixed-capacity system.
Multi-zone and VRF charge is always the calculated field addition described in Section 14.2.
Verification after charging — the readings that do mean something:
Compare indoor coil entering and leaving air temperatures and compute capacity (Section 11.2).
Compare compressor operating frequency and current against the manufacturer's data at the observed conditions.
Read EEV step count and calculated superheat from the service tool.
Confirm no fault codes are logged.
5. Start-Up and Commissioning
Confirm supply voltage and that the interconnecting cable is landed on matching terminals (Section 14.1).
Power the system and allow the crankcase heater — where fitted — its specified warm-up period.
Observe the EEV initialization click at power-up.
Run in cooling , then in heating , and verify mode change occurs.
Verify the indoor blower ramps through its speeds , that the louvers sweep, and that the remote or wired controller commands take effect.
Verify condensate drainage : pour water into the pan and confirm it exits outdoors, and on cassettes confirm the pump runs and the float switch functions.
Record line-set length, total charge, operating frequency, currents, air temperatures, and any commissioning settings on a start-up sheet left with the equipment.
Set the controller defaults the customer will actually use, and explain that the system is designed to run continuously at low speed rather than cycle — the same conversation as Section 9.5.
6. Diagnostics
Read the fault code first. Ductless equipment reports faults through blinking LED patterns on the indoor and outdoor boards, an alphanumeric code on the indoor display, or a service tool. Every manufacturer publishes a code table in the service manual. The code narrows the problem from the whole system to one subsystem before a single panel comes off.
Common code family What it usually means
Communication error Interconnecting cable miswired, loose, spliced, or picking up noise; failed indoor or outdoor board
Sensor / thermistor error Open or shorted thermistor, or a connector unseated. Verify with a resistance measurement against the temperature-resistance table before replacing a board
- High pressure / discharge temperature Overcharge, restricted condenser airflow, blocked EEV, non-condensables
- Low pressure / low suction Undercharge, leak, restricted indoor airflow, EEV stuck closed
Inverter / IPM error Drive fault — check supply voltage, voltage imbalance across the DC bus, and grounding before condemning the board
- Fan motor error Blocked wheel, failed motor Hall sensor, or a wiring fault
- Water level / float switch Condensate pump or drain blockage
Two diagnostic habits that matter most on ductless equipment:
Verify a sensor before replacing a board. A single drifted thermistor makes a healthy system behave erratically, because the board is controlling to a false number.
Discharge the DC bus and confirm zero volts before touching an inverter board (Section 14.1). The capacitors hold a lethal charge after the disconnect is opened.