Study guide
2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations
HVAC Excellence Certification Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction, Safety, Tools, and Diagnostic Method
1.1 HVAC Excellence Certification, Industry Codes, and Standards 1.2 Electrical Safety, PPE, Lockout/Tagout, and Hazard Communication 1.3 Multimeters, Manifold Gauges, Micron Gauges, and Diagnostic Instruments 1.4 HVACR Mathematics, Unit Conversions, and Efficiency Ratings 1.5 OSHA Standards, Fall Protection, Rigging, and Confined Spaces 1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs 1.7 Systematic Troubleshooting: Data Plates, Manufacturer Literature, and Diagnostic Method
2 Chapter 2: Electrical Fundamentals and Circuit Theory
2.1 Voltage, Current, Resistance, and Ohm's Law Calculations 2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations 2.3 AC Fundamentals, Single-Phase vs Three-Phase Power, and Control Transformers 2.4 Conductors, Insulators, Wire Sizing, Voltage Drop, and NEC Ampacity
3 Chapter 3: Electrical Components, Motors, and Schematics
3.1 Contactors, Relays, Switches, Overload Protection, and Thermostats 3.2 HVAC Motors (PSC, CSIR, CSCR, ECM, 3-Phase) and Run/Start Capacitors 3.3 Interpreting Ladder Diagrams, Schematics, and Point-to-Point Wiring 3.4 Motor Testing, Insulation Resistance, Bearings, and Belt Drives
4 Chapter 4: Thermodynamics and the Refrigeration Cycle
4.1 Heat Transfer, Temperature Scales, BTUs, Sensible vs Latent Heat, and Enthalpy 4.2 The Four Vapor-Compression Cycle Stages (Compression, Condensation, Expansion, Evaporation) 4.3 P-T Charts, Saturated Conditions, Target Superheat, and Subcooling Calculations 4.4 Pressure–Enthalpy Diagrams, Compression Ratio, and Cycle Analysis
5 Chapter 5: Refrigerants, Environmental Regulations, and Recovery
5.1 Refrigerant Types (CFC, HCFC, HFC, HFO, HC) and ASHRAE Safety Groups (A1, A2L, A3) 5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards 5.3 Recovery/Recycling/Reclaiming Equipment, Procedures, and Leak Detection 5.4 Refrigerant Retrofits, Cylinder Handling, and Refrigerant Purity 5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice
6 Chapter 6: Refrigeration System Components and Accessories
6.1 Compressor Mechanics (Reciprocating, Scroll, Rotary, Screw) and Failures 6.2 Expansion Devices (TXV/TEV, Fixed Orifice, EEV) and Superheat Control 6.3 Condensers, Evaporators, Filter-Driers, Accumulators, Receivers, and Solenoids 6.4 Pressure Controls, Capacity Controls, and System Protection 6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice
7 Chapter 7: Gas Heating, Combustion Analysis, and Fuel Piping
7.1 Combustion Theory, Fuel Gases (Natural Gas vs LP), and Gas Burners 7.2 Gas Valves, Ignition Systems (Standing Pilot, Spark, HSI), and Safety Limit Controls 7.3 Flue Venting, Draft Principles, Combustion Analysis, and CO Safety 7.4 Fuel-Gas and Oil Piping, Vent System Selection and Sizing, and Installation Practice
8 Chapter 8: Electric Heating, Oil Heat, and Hydronics
8.1 Electric Heating Elements, Sequencers, Limit Switches, and kW Calculations 8.2 Oil Burners, Fuel Pumps, Nozzles, Ignition Electrodes, and Primary Controls 8.3 Hydronic Boilers, Circulator Pumps, Expansion Tanks, and Zone Controls 8.4 Combustion Air, Water Heaters, and Combustion Appliance Zone Testing
9 Chapter 9: Heat Pumps and Dual-Fuel Systems
9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation 9.2 Defrost Controls (Time-Temperature, Demand Defrost), Sensors, and Sequences 9.3 Balance Points, Auxiliary/Emergency Heat, and Dual-Fuel (Hybrid) Systems 9.4 Heat Pump Diagnostics, Refrigerant Flow, and Troubleshooting Procedures 9.5 Heat Pump Types, Cold-Climate Performance, and Sizing Approaches
10 Chapter 10: Air Distribution, IAQ, and System Commissioning
10.1 Airflow Fundamentals, CFM Measurement, External Static Pressure, and Fan Laws 10.2 Duct Sizing Principles, Supply/Return Distribution, Dampers, and Air Balancing 10.3 Indoor Air Quality, MERV Ratings, Electronic Cleaners, Humidification, and Dehumidification 10.4 Deep Vacuum Evacuation (Micron Gauge), Subcooling/Superheat Charging, and System Commissioning 10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance
11 Chapter 11: Psychrometrics, Airside Calculations, and Load Estimation
11.1 Reading the Psychrometric Chart: Properties and Plotting 11.2 The Eight Air-Conditioning Processes and the Process Triangle 11.3 Mixed Air, Ventilation, and Infiltration Calculations 11.4 Residential Heat Loss, Heat Gain, and Equipment Sizing
12 Chapter 12: Light Commercial Air Conditioning
12.1 Packaged Rooftop and Split Light-Commercial Systems 12.2 Water-Cooled Condensers, Cooling Towers, and Chilled-Water Systems 12.3 Economizers, Demand-Controlled Ventilation, and VAV Air Distribution 12.4 Light-Commercial Start-Up, Commissioning, and Troubleshooting
13 Chapter 13: Light Commercial Refrigeration
13.1 Temperature Ranges, Box Loads, and Refrigeration System Types 13.2 Evaporators, Defrost Methods, and Defrost Controls 13.3 Condensing Units, Parallel Racks, Oil Management, and Capacity Control 13.4 Refrigeration Control Valves and Automatic Pump-Down 13.5 Commercial Refrigeration Diagnostics and Ice Machines
14 Chapter 14: Ductless, Mini-Split, and VRF Systems
14.1 Mini-Split Architecture and Inverter-Driven Compressors 14.2 Multi-Zone and VRF Operation, Electronic Expansion Valves, and Controls 14.3 Ductless Installation, Evacuation, Charging, and Diagnostics
15 Chapter 15: Building Automation and Digital Controls
15.1 DDC Fundamentals, Control Loops, and Sequences of Operation 15.2 BAS Networks, Protocols, and NEC-Compliant Cabling 15.3 Building Automation Controllers: Supervisory, Field, and Room Devices 15.4 Digital Logic, Numbering Systems, and Controller Programming 15.5 Sensor Selection, Installation, and Input Point Configuration 15.6 Actuators, Output Devices, and VFD Integration 15.7 Commercial Prints, Equipment Schedules, and BAS Documentation
2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations
Key Takeaways Explain This Topic AI
In a series circuit, current is identical through all components, total resistance is the sum of all individual resistances, and applied voltage divides proportionally across loads.
In a parallel circuit, voltage is identical across all branches, total current equals the sum of individual branch currents, and total equivalent resistance is always less than the lowest branch resistance.
HVAC safety controls (pressure switches, limit switches, freeze stats) are always wired in series with the control load, while primary power loads (compressors, condenser fans, blower motors) are wired in parallel across line voltage.
Real Power (Watts) performs actual work; Apparent Power (Volt-Amps) is the total supplied power; Reactive Power (VARs) sustains electromagnetic fields in inductive motor windings.
Power Factor (PF = Real Power / Apparent Power = cos θ) measures electrical efficiency; run capacitors provide leading reactive power to correct lagging power factors toward unity.
Last updated: August 2026
2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations
Every electrical schematic in an air conditioner, heat pump, refrigeration rack, or gas furnace is composed of basic circuit arrangements: series, parallel, or complex combination (series-parallel) networks. Understanding how voltage, current, resistance, and power behave across these configurations is essential for diagnosing open circuits, component failures, and electrical power quality issues.
1. Series Circuit Principles and Laws
A series circuit provides only one single, continuous path for electron flow. All components are connected end-to-end like links in a chain.
The Three Fundamental Laws of Series Circuits
Current is Constant Throughout: Because there is only one path, the exact same rate of electron flow passes through every component: I total = I 1 = I 2 = I 3 = ⋯ = I n I_{\text{total}} = I_1 = I_2 = I_3 = \dots = I_n I total = I 1 = I 2 = I 3 = ⋯ = I n
Total Resistance is Additive: Each added resistive load increases the total opposition to electron flow in the circuit: R total = R 1 + R 2 + R 3 + ⋯ + R n R_{\text{total}} = R_1 + R_2 + R_3 + \dots + R_n R total = R 1 + R 2 + R 3 + ⋯ + R n
Voltage Divides Across Loads (Kirchhoff's Voltage Law - KVL): The total applied source voltage equals the sum of the individual voltage drops across each series load, with voltage dividing in direct proportion to each component's resistance ( E n = I × R n E_n = I \times R_n E n = I × R n ): E total = E 1 + E 2 + E 3 + ⋯ + E n E_{\text{total}} = E_1 + E_2 + E_3 + \dots + E_n E total = E 1 + E 2 + E 3 + ⋯ + E n
Component Faults in Series Circuits
Open Circuit Fault: If any single switch or component opens in a series string, total current immediately drops to zero ( I = 0 A I = 0\text{ A} I = 0 A ). The entire circuit stops operating. The full source voltage appears across the open contact.
Short Circuit Fault: If one component in a series string shorts out ( R = 0 Ω R = 0\ \Omega R = 0 Ω ), total circuit resistance decreases ( R total ↓ R_{\text{total}} \downarrow R total ↓ ), causing total current to increase ( I total ↑ I_{\text{total}} \uparrow I total ↑ ). The remaining components experience higher voltage drops and higher current, which can lead to thermal overload.
HVAC Application: The Series Safety String
In HVAC systems, safety and operating limit controls are always wired in series with the load they protect (e.g., compressor contactor coil, gas valve). These safety devices include:
- High-pressure cutout switch (opens on excessive head pressure)
- Low-pressure cutout / loss-of-charge switch (opens on low suction pressure)
- Compressor internal thermal overload / discharge line thermostat
- High limit switch (opens on furnace heat exchanger overheating)
- Flame rollout safety switch (opens on burner draft failure)
- Condensate overflow float switch
- Freeze protection thermostat (freeze stat on water chillers or evaporator coils)
Why? If any single safety control detects an unsafe operating condition and opens its contacts, the single path for control current is severed, immediately de-energizing the contactor coil or gas valve and protecting equipment and building occupants.
Loading diagram... HVAC Control Circuit Architecture: Series Safety Chain Feeding Parallel Operational Loads
2. Parallel Circuit Principles and Laws
A parallel circuit contains two or more distinct branches connected across the same common voltage source, providing multiple independent paths for electron flow.
The Three Fundamental Laws of Parallel Circuits
Voltage is Constant Across All Branches: Every parallel branch connects directly across the full line voltage: E total = E 1 = E 2 = E 3 = ⋯ = E n E_{\text{total}} = E_1 = E_2 = E_3 = \dots = E_n E total = E 1 = E 2 = E 3 = ⋯ = E n
Current is Additive (Kirchhoff's Current Law - KCL): Total current entering a common junction equals the sum of the individual branch currents flowing out of that junction: I total = I 1 + I 2 + I 3 + ⋯ + I n I_{\text{total}} = I_1 + I_2 + I_3 + \dots + I_n I total = I 1 + I 2 + I 3 + ⋯ + I n
Total Equivalent Resistance Decreases: Adding parallel branches creates additional paths for current flow, reducing the overall equivalent resistance of the network. Total resistance is always less than the resistance of the smallest individual branch: 1 R total = 1 R 1 + 1 R 2 + 1 R 3 + ⋯ + 1 R n \frac{1}{R_{\text{total}}} = \frac{1}{R_1} + \frac{1}{R_2} + \frac{1}{R_3} + \dots + \frac{1}{R_n} R total 1 = R 1 1 + R 2 1 + R 3 1 + ⋯ + R n 1
Mathematical Shortcuts for Parallel Resistors
Product Over Sum Formula (for exactly two parallel resistors): R total = R 1 × R 2 R 1 + R 2 R_{\text{total}} = \frac{R_1 \times R_2}{R_1 + R_2} R total = R 1 + R 2 R 1 × R 2
Equal Value Resistors in Parallel ( N N N identical resistors of value R R R ): R total = R N R_{\text{total}} = \frac{R}{N} R total = N R Example: Three 30 Ω 30\ \Omega 30 Ω crankcase heaters wired in parallel produce R total = 30 / 3 = 10 Ω R_{\text{total}} = 30 / 3 = 10\ \Omega R total = 30/3 = 10 Ω .
Component Faults in Parallel Circuits
Open Branch Fault: If one branch opens (e.g., a burned-out crankcase heater or outdoor fan motor), only that specific branch ceases to function. All other parallel branches continue to receive full supply voltage and operate normally.
Short Circuit Fault: If a dead short ( R = 0 Ω R = 0\ \Omega R = 0 Ω ) occurs in any single parallel branch, the entire power supply rail is shorted directly to neutral or ground. Total resistance drops to near zero, creating massive fault current that instantly opens the branch overcurrent protective device (fuse or circuit breaker).
HVAC Application: Parallel Line-Voltage Power Loads
All primary operating loads in residential and commercial HVAC units—such as the compressor motor, outdoor condenser fan motor, indoor blower motor, crankcase heater, and electric heat elements—are wired in parallel across the main supply voltage . This ensures every motor and heater receives full design operating voltage (e.g., 240 VAC) regardless of which other components are cycling on or off.
3. Series-Parallel (Combination) Circuits
Practical HVAC machinery combines series and parallel networks into series-parallel combination circuits . In these circuits, switches and safety controls are wired in series with parallel load banks, or complex relay logic routes power through interconnected branches.
Analysis Method: Circuit Reduction
To analyze a combination circuit:
Identify purely parallel sub-branches and calculate their single equivalent resistance ( R p R_p R p ).
Replace the parallel branches with their equivalent resistance ( R p R_p R p ) to form a simplified series circuit.
Sum all remaining series resistances ( R total = R s + R p R_{\text{total}} = R_s + R_p R total = R s + R p ).
Use Ohm's Law to determine total current ( I total = E / R total I_{\text{total}} = E / R_{\text{total}} I total = E / R total ).
Calculate the voltage drop across the series section ( V s = I total × R s V_s = I_{\text{total}} \times R_s V s = I total × R s ).
Subtract the series voltage drop from total voltage to find the remaining voltage across the parallel branch bank ( V p = E total − V s V_p = E_{\text{total}} - V_s V p = E total − V s ).
Calculate individual branch currents ( I n = V p / R n I_n = V_p / R_n I n = V p / R n ).
- 4. Worked Calculation Examples
- Example 1: Parallel Electric Heating Element Bank
Problem: An electric furnace contains three resistive heating elements wired in parallel across a 240 VAC power supply. The hot resistances are R 1 = 20 Ω R_1 = 20\ \Omega R 1 = 20 Ω , R 2 = 24 Ω R_2 = 24\ \Omega R 2 = 24 Ω , and R 3 = 30 Ω R_3 = 30\ \Omega R 3 = 30 Ω .
Calculate the total equivalent resistance ( R total R_{\text{total}} R total ) of the heating bank.
Calculate the individual branch currents ( I 1 , I 2 , I 3 I_1, I_2, I_3 I 1 , I 2 , I 3 ).
Calculate the total line current ( I total I_{\text{total}} I total ).
Calculate the total power consumed in kW and total heat output in BTU/hr.
Solution Steps:
Step 1: Calculate Total Equivalent Resistance: 1 R total = 1 20 + 1 24 + 1 30 = 0.050 + 0.04167 + 0.03333 = 0.125 Ω − 1 \frac{1}{R_{\text{total}}} = \frac{1}{20} + \frac{1}{24} + \frac{1}{30} = 0.050 + 0.04167 + 0.03333 = 0.125\ \Omega^{-1} R total 1 = 20 1 + 24 1 + 30 1 = 0.050 + 0.04167 + 0.03333 = 0.125 Ω − 1 R total = 1 0.125 = 8.0 Ω R_{\text{total}} = \frac{1}{0.125} = 8.0\ \Omega R total = 0.125 1 = 8.0 Ω
Step 2: Calculate Individual Branch Currents: I 1 = 240 V 20 Ω = 12.0 A , I 2 = 240 V 24 Ω = 10.0 A , I 3 = 240 V 30 Ω = 8.0 A I_1 = \frac{240\text{ V}}{20\ \Omega} = 12.0\text{ A}, \quad I_2 = \frac{240\text{ V}}{24\ \Omega} = 10.0\text{ A}, \quad I_3 = \frac{240\text{ V}}{30\ \Omega} = 8.0\text{ A} I 1 = 20 Ω 240 V = 12.0 A , I 2 = 24 Ω 240 V = 10.0 A , I 3 = 30 Ω 240 V = 8.0 A
Step 3: Calculate Total Line Current: I total = I 1 + I 2 + I 3 = 12.0 A + 10.0 A + 8.0 A = 30.0 A I_{\text{total}} = I_1 + I_2 + I_3 = 12.0\text{ A} + 10.0\text{ A} + 8.0\text{ A} = 30.0\text{ A} I total = I 1 + I 2 + I 3 = 12.0 A + 10.0 A + 8.0 A = 30.0 A Verification via Ohm's Law: I total = E / R total = 240 V / 8.0 Ω = 30.0 A I_{\text{total}} = E / R_{\text{total}} = 240\text{ V} / 8.0\ \Omega = 30.0\text{ A} I total = E / R total = 240 V /8.0 Ω = 30.0 A (Matches).
Step 4: Calculate Power and Heat Output: P total = E × I total = 240 V × 30.0 A = 7 , 200 Watts = 7.2 kW P_{\text{total}} = E \times I_{\text{total}} = 240\text{ V} \times 30.0\text{ A} = 7,200\text{ Watts} = 7.2\text{ kW} P total = E × I total = 240 V × 30.0 A = 7 , 200 Watts = 7.2 kW Q heat = 7.2 kW × 3 , 412.14 BTU/kW = 24 , 567.4 BTU/hr Q_{\text{heat}} = 7.2\text{ kW} \times 3,412.14\text{ BTU/kW} = 24,567.4\text{ BTU/hr} Q heat = 7.2 kW × 3 , 412.14 BTU/kW = 24 , 567.4 BTU/hr
5. AC Power Components: Watts, Volt-Amperes, VARs, and Power Factor
In AC circuits containing inductive loads (compressor motors, fan motors, contactor coils) or capacitive loads (run capacitors, start capacitors), voltage and current sine waves do not peak at the exact same instant. This phase displacement creates three distinct types of electrical power:
The Three Components of AC Power
Real Power (True Power - P P P ):
Measured in Watts (W) or Kilowatts (kW) .
The actual rate at which electrical energy is converted into usable mechanical work, heat, or light by resistive components.
Formula: P = E × I × cos ( θ ) P = E \times I \times \cos(\theta) P = E × I × cos ( θ )
Apparent Power ( S S S ):
Measured in Volt-Amperes (VA) or Kilovolt-Amperes (kVA) .
The total "raw" power supplied to the circuit by the utility or control transformer, calculated as the simple scalar product of total RMS voltage and total RMS current.
Formula: S = E × I S = E \times I S = E × I
Reactive Power ( Q Q Q ):
Measured in Volt-Amperes Reactive (VAR) or kVAR .
The non-working power that oscillates back and forth between the power source and the magnetic fields of inductors (motor windings, transformers) or the electric fields of capacitors.
Formula: Q = E × I × sin ( θ ) Q = E \times I \times \sin(\theta) Q = E × I × sin ( θ )
The Power Triangle and Pythagorean Relationship Apparent Power 2 = Real Power 2 + Reactive Power 2 \text{Apparent Power}^2 = \text{Real Power}^2 + \text{Reactive Power}^2 Apparent Power 2 = Real Power 2 + Reactive Power 2 S = P 2 + Q 2 S = \sqrt{P^2 + Q^2} S = P 2 + Q 2
Power Metric Symbol Unit Physical Manifestation in HVAC
Real Power P P P Watts (W) / kW Heat from electric strip elements, mechanical shaft torque of motors, utility meter billing energy.
Apparent Power S S S Volt-Amps (VA) / kVA Rating of step-down control transformers (40VA, 75VA), total ampacity demand on wires and breakers.
Reactive Power Q Q Q VAR / kVAR Magnetic flux sustaining stator rotation in induction motors (inductive VARs) vs electrostatic field in run capacitors (capacitive VARs).
Power Factor (PF) and Its Practical Importance
Power Factor is the ratio of Real Power (Watts) doing actual work to the total Apparent Power (VA) supplied by the electrical source: Power Factor (PF) = Real Power (Watts) Apparent Power (VA) = cos ( θ ) \text{Power Factor (PF)} = \frac{\text{Real Power (Watts)}}{\text{Apparent Power (VA)}} = \cos(\theta) Power Factor (PF) = Apparent Power (VA) Real Power (Watts) = cos ( θ ) Percentage PF = ( Watts VA ) × 100 % \text{Percentage PF} = \left(\frac{\text{Watts}}{\text{VA}}\right) \times 100\% Percentage PF = ( VA Watts ) × 100%
Power Factor Correction in HVAC
Inductive Loads (Lagging PF): Single-phase and three-phase induction motors draw magnetizing current that causes the current waveform to lag behind the voltage waveform , resulting in a poor power factor (typically 0.70 to 0.85). This low PF forces the motor to draw higher total line current (Amps) for the same delivered mechanical horsepower.
Capacitive Correction (Leading PF): Motor permanent split capacitor (PSC) run capacitors supply leading reactive power (capacitive VARs) that directly counteracts and cancels the lagging inductive VARs of the motor windings. This brings total voltage and current closer into phase, raising the operating power factor to 0.90–0.98, which reduces total line current, lowers conductor I 2 R I^2 R I 2 R heat losses, and prevents premature nuisance tripping of circuit breakers.