Study guide

9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation

HVAC Excellence Certification Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction, Safety, Tools, and Diagnostic Method

1.1 HVAC Excellence Certification, Industry Codes, and Standards 1.2 Electrical Safety, PPE, Lockout/Tagout, and Hazard Communication 1.3 Multimeters, Manifold Gauges, Micron Gauges, and Diagnostic Instruments 1.4 HVACR Mathematics, Unit Conversions, and Efficiency Ratings 1.5 OSHA Standards, Fall Protection, Rigging, and Confined Spaces 1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs 1.7 Systematic Troubleshooting: Data Plates, Manufacturer Literature, and Diagnostic Method

2 Chapter 2: Electrical Fundamentals and Circuit Theory

2.1 Voltage, Current, Resistance, and Ohm's Law Calculations 2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations 2.3 AC Fundamentals, Single-Phase vs Three-Phase Power, and Control Transformers 2.4 Conductors, Insulators, Wire Sizing, Voltage Drop, and NEC Ampacity

3 Chapter 3: Electrical Components, Motors, and Schematics

3.1 Contactors, Relays, Switches, Overload Protection, and Thermostats 3.2 HVAC Motors (PSC, CSIR, CSCR, ECM, 3-Phase) and Run/Start Capacitors 3.3 Interpreting Ladder Diagrams, Schematics, and Point-to-Point Wiring 3.4 Motor Testing, Insulation Resistance, Bearings, and Belt Drives

4 Chapter 4: Thermodynamics and the Refrigeration Cycle

4.1 Heat Transfer, Temperature Scales, BTUs, Sensible vs Latent Heat, and Enthalpy 4.2 The Four Vapor-Compression Cycle Stages (Compression, Condensation, Expansion, Evaporation) 4.3 P-T Charts, Saturated Conditions, Target Superheat, and Subcooling Calculations 4.4 Pressure–Enthalpy Diagrams, Compression Ratio, and Cycle Analysis

5 Chapter 5: Refrigerants, Environmental Regulations, and Recovery

5.1 Refrigerant Types (CFC, HCFC, HFC, HFO, HC) and ASHRAE Safety Groups (A1, A2L, A3) 5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards 5.3 Recovery/Recycling/Reclaiming Equipment, Procedures, and Leak Detection 5.4 Refrigerant Retrofits, Cylinder Handling, and Refrigerant Purity 5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice

6 Chapter 6: Refrigeration System Components and Accessories

6.1 Compressor Mechanics (Reciprocating, Scroll, Rotary, Screw) and Failures 6.2 Expansion Devices (TXV/TEV, Fixed Orifice, EEV) and Superheat Control 6.3 Condensers, Evaporators, Filter-Driers, Accumulators, Receivers, and Solenoids 6.4 Pressure Controls, Capacity Controls, and System Protection 6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice

7 Chapter 7: Gas Heating, Combustion Analysis, and Fuel Piping

7.1 Combustion Theory, Fuel Gases (Natural Gas vs LP), and Gas Burners 7.2 Gas Valves, Ignition Systems (Standing Pilot, Spark, HSI), and Safety Limit Controls 7.3 Flue Venting, Draft Principles, Combustion Analysis, and CO Safety 7.4 Fuel-Gas and Oil Piping, Vent System Selection and Sizing, and Installation Practice

8 Chapter 8: Electric Heating, Oil Heat, and Hydronics

8.1 Electric Heating Elements, Sequencers, Limit Switches, and kW Calculations 8.2 Oil Burners, Fuel Pumps, Nozzles, Ignition Electrodes, and Primary Controls 8.3 Hydronic Boilers, Circulator Pumps, Expansion Tanks, and Zone Controls 8.4 Combustion Air, Water Heaters, and Combustion Appliance Zone Testing

9 Chapter 9: Heat Pumps and Dual-Fuel Systems

9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation 9.2 Defrost Controls (Time-Temperature, Demand Defrost), Sensors, and Sequences 9.3 Balance Points, Auxiliary/Emergency Heat, and Dual-Fuel (Hybrid) Systems 9.4 Heat Pump Diagnostics, Refrigerant Flow, and Troubleshooting Procedures 9.5 Heat Pump Types, Cold-Climate Performance, and Sizing Approaches

10 Chapter 10: Air Distribution, IAQ, and System Commissioning

10.1 Airflow Fundamentals, CFM Measurement, External Static Pressure, and Fan Laws 10.2 Duct Sizing Principles, Supply/Return Distribution, Dampers, and Air Balancing 10.3 Indoor Air Quality, MERV Ratings, Electronic Cleaners, Humidification, and Dehumidification 10.4 Deep Vacuum Evacuation (Micron Gauge), Subcooling/Superheat Charging, and System Commissioning 10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance

11 Chapter 11: Psychrometrics, Airside Calculations, and Load Estimation

11.1 Reading the Psychrometric Chart: Properties and Plotting 11.2 The Eight Air-Conditioning Processes and the Process Triangle 11.3 Mixed Air, Ventilation, and Infiltration Calculations 11.4 Residential Heat Loss, Heat Gain, and Equipment Sizing

12 Chapter 12: Light Commercial Air Conditioning

12.1 Packaged Rooftop and Split Light-Commercial Systems 12.2 Water-Cooled Condensers, Cooling Towers, and Chilled-Water Systems 12.3 Economizers, Demand-Controlled Ventilation, and VAV Air Distribution 12.4 Light-Commercial Start-Up, Commissioning, and Troubleshooting

13 Chapter 13: Light Commercial Refrigeration

13.1 Temperature Ranges, Box Loads, and Refrigeration System Types 13.2 Evaporators, Defrost Methods, and Defrost Controls 13.3 Condensing Units, Parallel Racks, Oil Management, and Capacity Control 13.4 Refrigeration Control Valves and Automatic Pump-Down 13.5 Commercial Refrigeration Diagnostics and Ice Machines

14 Chapter 14: Ductless, Mini-Split, and VRF Systems

14.1 Mini-Split Architecture and Inverter-Driven Compressors 14.2 Multi-Zone and VRF Operation, Electronic Expansion Valves, and Controls 14.3 Ductless Installation, Evacuation, Charging, and Diagnostics

15 Chapter 15: Building Automation and Digital Controls

15.1 DDC Fundamentals, Control Loops, and Sequences of Operation 15.2 BAS Networks, Protocols, and NEC-Compliant Cabling 15.3 Building Automation Controllers: Supervisory, Field, and Room Devices 15.4 Digital Logic, Numbering Systems, and Controller Programming 15.5 Sensor Selection, Installation, and Input Point Configuration 15.6 Actuators, Output Devices, and VFD Integration 15.7 Commercial Prints, Equipment Schedules, and BAS Documentation

9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation

Key Takeaways Explain This Topic AI

The 4-way reversing valve alters the direction of refrigerant flow to switch between cooling (indoor coil as evaporator, outdoor coil as condenser) and heating (indoor coil as condenser, outdoor coil as evaporator).

The single top port of the reversing valve always connects to the compressor discharge (high pressure vapor), and the bottom center port always connects to the compressor suction/accumulator (low pressure vapor).

The reversing valve slide mechanism is moved pneumatically by system differential pressure (minimum 50 to 75 psi ΔP required), piloted by an electromagnetic solenoid valve with bleed ports.

Thermostat terminal designations standardly energize the reversing valve in cooling (O terminal, used by Carrier, Trane, Lennox, York) or in heating (B terminal, used by Rheem/Ruud).

Dual-direction refrigerant flow requires bi-flow filter-driers and either bi-flow expansion devices or dedicated TXVs/fixed orifices piped in parallel with bypass check valves.

Last updated: August 2026

9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation

Air-source heat pumps provide year-round environmental conditioning by reversing the direction of refrigerant flow through a standard vapor-compression refrigeration circuit. In cooling mode, the system extracts heat from the indoor conditioned space and rejects it to the outdoor ambient air. In heating mode, the refrigeration cycle operates in reverse: the outdoor coil absorbs heat from cold outdoor air—even at sub-freezing temperatures—and the indoor coil rejects that heat into the living space. Mastering the mechanics of the 4-way reversing valve, refrigerant circuit routing, terminal control logic, and dual expansion assemblies is a fundamental requirement for the HVAC Excellence Certification.

1. Thermodynamic Principles of Heat Pump Heating

Thermal energy naturally flows from a region of higher temperature to a region of lower temperature in accordance with the Second Law of Thermodynamics. A heat pump utilizes mechanical work input (via the compressor) to pump thermal energy uphill from a low-temperature outdoor reservoir to a high-temperature indoor reservoir.

Heat Extraction from Cold Ambient Air

All matter above absolute zero (0 Kelvin or -459.67°F) contains thermal energy. Air at 20°F (-6.7°C) or even 0°F (-17.8°C) possesses substantial heat energy. To extract this heat:

The system routes cold, low-pressure liquid-vapor refrigerant through the outdoor coil (which serves as the evaporator in heating mode).

The saturation temperature (boiling point) of the refrigerant inside the outdoor coil is maintained at 10°F to 20°F (5.5°C to 11.1°C) below the outdoor ambient air temperature .

Because the outdoor ambient air is warmer than the boiling refrigerant inside the tubes, heat transfers from the outdoor air into the refrigerant, evaporating the liquid into a cold vapor.

The compressor draws in this cold vapor, compresses it, and elevates its pressure and temperature to a superheated vapor state (typically 160°F to 200°F / 71°C to 93°C).

The hot discharge gas is pumped to the indoor coil (which serves as the condenser in heating mode), where the 70°F indoor return air absorbs heat from the 110°F–120°F condensing refrigerant. Heat Absorption (Outdoor Evaporator): Q in = m ˙ × ( h suction − h liquid, outdoor ) \text{Heat Absorption (Outdoor Evaporator): } Q_{\text{in}} = \dot{m} \times (h_{\text{suction}} - h_{\text{liquid, outdoor}}) Heat Absorption (Outdoor Evaporator): Q in ​ = m ˙ × ( h suction ​ − h liquid, outdoor ​ ) Heat Rejection (Indoor Condenser): Q out = m ˙ × ( h discharge − h liquid, indoor ) \text{Heat Rejection (Indoor Condenser): } Q_{\text{out}} = \dot{m} \times (h_{\text{discharge}} - h_{\text{liquid, indoor}}) Heat Rejection (Indoor Condenser): Q out ​ = m ˙ × ( h discharge ​ − h liquid, indoor ​ ) Total Heating Delivered: Q out = Q in + W compressor \text{Total Heating Delivered: } Q_{\text{out}} = Q_{\text{in}} + W_{\text{compressor}} Total Heating Delivered: Q out ​ = Q in ​ + W compressor ​

Notice that in heating mode, the heat delivered to the indoor space equals the heat absorbed from the outdoor environment plus the electrical energy converted to heat by the compressor motor ( W compressor W_{\text{compressor}} W compressor ​ ).

2. Construction and Mechanics of the 4-Way Reversing Valve

The 4-way reversing valve is the core component that directs high-pressure discharge gas to either the indoor or outdoor coil while directing low-pressure vapor back to the compressor suction. [Top Single Port]

  • (Compressor Discharge)
  • │
  • ┌─────┴─────┐
  • │ VALVE │ ── [Pilot Solenoid Coil]
  • │ BODY │
  • └─────┬─────┘
  • ┌─────────────┼─────────────┐
  • │ │ │
  • [Left Port] [Center Port] [Right Port]
  • (Outdoor Coil) (True Suction) (Indoor Coil)
  • Valve Port Geometry and Identification

Top Single Port: Always connects directly to the compressor discharge line . This port is subjected to continuous high-pressure, superheated discharge vapor whenever the compressor runs.

Bottom Center Port: Always connects to the compressor suction line (typically via the suction line accumulator). This port is always under low-pressure suction vapor.

Bottom Outer Left & Right Ports: One outer port connects to the indoor coil header , and the other outer port connects to the outdoor coil header .

Pneumatic Shifting and Pilot Solenoid Operation

A common misconception is that the electromagnetic solenoid coil has sufficient magnetic power to physically pull the large brass slide back and forth across the valve body. In reality, the slide is moved entirely by system refrigerant pressure differential (pneumatic force) .

The Pilot Solenoid and Capillary Bleed Tubes:

The main brass valve cylinder contains a sliding shuttle (slide mechanism) fitted with Teflon cups/piston seals at each end. Small bleed orifices (or capillary tubes) connect both ends of the cylinder to a miniature pilot solenoid valve.

High-pressure discharge gas continuously bleeds into both ends of the main cylinder through small orifice ports.

Shifting Mechanism:

When the solenoid coil changes state (energized or de-energized), the pilot needle valve opens a vent passage from one end of the cylinder to the center suction port.

Venting that end drops its internal pressure to low-side suction pressure. Meanwhile, the opposite end remains at high discharge pressure.

This creates a massive pneumatic differential across the slide piston. The slide snaps rapidly across the valve chamber, sealing the sliding cup over the appropriate ports.

Minimum Differential Pressure Requirement:

For the slide to shift and seat tightly, the system must generate a minimum differential pressure of 50 to 75 psi (345 to 517 kPa) between the high side and low side.

If a heat pump is severely short of refrigerant, if the compressor valves are broken, or if the valve is shifted when the compressor is not running, the slide will stall or hang in the center position, resulting in catastrophic blow-by.

3. Reversing Valve Thermostat Logic: O vs. B Terminal

Thermostats and control boards energize the reversing valve solenoid coil using low-voltage (24 VAC) control signals routed through specific sub-base terminals:

Terminal Energization State Fail-Safe (De-energized) Mode Primary Equipment Brands

O Terminal Energized in Cooling mode De-energized in Heating mode Carrier, Bryant, Payne, Trane, American Standard, Lennox, York, Goodman, Amana, Daikin

B Terminal Energized in Heating mode De-energized in Cooling mode Rheem, Ruud, WeatherKing

HVAC Excellence Exam Trap: Most manufacturers energize the reversing valve via the O terminal in Cooling mode, meaning the solenoid coil is energized all summer and de-energized all winter. If a homeowner loses 24V power or the solenoid coil burns out on an O -type system, the system fails into Heating mode —preventing frozen water pipes during a winter freeze. Conversely, Rheem/Ruud systems use the B terminal (energized in heating), which fails into Cooling mode upon coil failure.

4. Refrigerant Flow Paths: Cooling vs. Heating Mode

Understanding the exact flow path, pressure transitions, and component functions in both operating modes is essential for accurate diagnostics.

Cooling Mode Flow Path

Compression: The compressor discharges high-pressure, superheated vapor into the top single port of the reversing valve.

Outdoor Heat Rejection (Condenser): The internal slide directs the gas out through the outer port connected to the outdoor coil . The outdoor fan moves ambient air across the coil, condensing the refrigerant into a high-pressure subcooled liquid.

Liquid Line & Filtration: Liquid refrigerant flows through the liquid line and passes through the bi-flow filter-drier .

Expansion (Indoor Metering): The refrigerant bypasses the outdoor expansion device (via an open check valve) and flows to the indoor metering device (TXV or fixed orifice), expanding into a low-pressure, low-temperature liquid-vapor mixture.

Indoor Heat Absorption (Evaporator): The indoor coil absorbs sensible and latent heat from indoor air, evaporating the refrigerant into superheated low-pressure vapor.

Return to Suction: Superheated vapor flows through the vapor line, enters the reversing valve's indoor outer port, is routed under the slide cup into the center bottom suction port , passes through the suction accumulator, and enters the compressor.

Heating Mode Flow Path

Compression: High-pressure, superheated vapor leaves the compressor discharge and enters the top single port of the reversing valve.

Indoor Heat Rejection (Condenser): The slide directs hot discharge gas through the indoor outer port into the indoor coil (now acting as the condenser). Indoor return air absorbs heat from the condensing refrigerant, warming the building.

Liquid Line & Filtration: High-pressure subcooled liquid exits the indoor coil, passes through the bi-flow filter-drier toward the outdoor unit.

Expansion (Outdoor Metering): The indoor expansion check valve opens, allowing unrestricted flow around the indoor metering device. Liquid is forced through the outdoor metering device (outdoor TXV or fixed orifice), dropping to low pressure and low saturation temperature.

Outdoor Heat Absorption (Evaporator): The cold liquid-vapor mixture flows through the outdoor coil (now acting as the evaporator), absorbing heat from the outdoor air.

Return to Suction: Superheated vapor exits the outdoor coil, enters the outdoor outer port of the reversing valve, is directed into the center bottom suction port , flows through the accumulator, and returns to the compressor suction inlet.

  • Cycle Parameter Cooling Mode Heating Mode
  • Indoor Coil Function Evaporator (Heat Absorption) Condenser (Heat Rejection)
  • Outdoor Coil Function Condenser (Heat Rejection) Evaporator (Heat Absorption)

Large Insulated Vapor Line Low-Pressure Cold Vapor (~40°F–50°F / 118–143 psig R-410A) High-Pressure Superheated Gas (~120°F–180°F / 300–420 psig R-410A)

  • Small Liquid Line High-Pressure Subcooled Liquid (~90°F–105°F) High-Pressure Subcooled Liquid (~80°F–100°F)
  • Active Metering Device Indoor TXV / Orifice Outdoor TXV / Orifice
  • Bypassed Metering Device Outdoor Check Valve Open Indoor Check Valve Open

Loading diagram... 4-Way Reversing Valve Porting and Dual Mode Flow Paths

5. Dual Expansion Devices and Bi-Flow Filtration

Because refrigerant flows in opposite directions through the liquid and vapor piping depending on the season, conventional single-direction refrigeration accessories cannot be used.

Bi-Flow Filter-Driers

A standard liquid line filter-drier contains desiccant beads and a particulate filter pad designed for one-way flow. If standard one-way filter-driers are installed on a heat pump, reverse flow washes trapped contaminants, moisture, and acid directly back into the metering devices and compressor.

Construction: A bi-flow filter-drier incorporates internal floating check valves or twin check-ball conduits.

Operation: When refrigerant enters from either direction, the incoming pressure forces an internal check valve against its seat, routing liquid inward through the outer circumference of the desiccant core and out through the clean center core, regardless of flow direction. Flow Direction A ──> [Check Ball 1 Seats] ──> [Desiccant Core] ──> [Check Ball 2 Unseats] ──> Out

  • Flow Direction B <── [Check Ball 1 Unseats] <── [Desiccant Core] <── [Check Ball 2 Seats] <── In
  • Dual Expansion Device Configurations

Because each coil requires precise superheat control when acting as an evaporator, heat pumps must employ dedicated expansion devices for each coil:

Parallel Check-Valve and TXV Circuits:

A mechanical check valve is piped in parallel with each Thermostatic Expansion Valve (TXV).

In Cooling Mode , the outdoor check valve is forced open by the high-pressure liquid exiting the outdoor condenser, bypassing the outdoor TXV with zero pressure drop. At the indoor unit, the high pressure forces the indoor check valve tightly against its seat, forcing all liquid through the indoor TXV.

In Heating Mode , the indoor check valve opens, allowing liquid from the indoor condenser to bypass the indoor TXV unrestricted. At the outdoor unit, the check valve closes, forcing liquid through the outdoor TXV to meter into the outdoor evaporator.

Bi-Flow Electronic Expansion Valves (EEVs):

Modern inverter and variable-capacity heat pumps use a single or dual stepper-motor-driven bi-flow EEV. The microprocessor detects whether the system is in heating or cooling mode and repositions the needle valve to meter refrigerant in either direction, eliminating mechanical check valves entirely.