Study guide

1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs

HVAC Excellence Certification Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction, Safety, Tools, and Diagnostic Method

1.1 HVAC Excellence Certification, Industry Codes, and Standards 1.2 Electrical Safety, PPE, Lockout/Tagout, and Hazard Communication 1.3 Multimeters, Manifold Gauges, Micron Gauges, and Diagnostic Instruments 1.4 HVACR Mathematics, Unit Conversions, and Efficiency Ratings 1.5 OSHA Standards, Fall Protection, Rigging, and Confined Spaces 1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs 1.7 Systematic Troubleshooting: Data Plates, Manufacturer Literature, and Diagnostic Method

2 Chapter 2: Electrical Fundamentals and Circuit Theory

2.1 Voltage, Current, Resistance, and Ohm's Law Calculations 2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations 2.3 AC Fundamentals, Single-Phase vs Three-Phase Power, and Control Transformers 2.4 Conductors, Insulators, Wire Sizing, Voltage Drop, and NEC Ampacity

3 Chapter 3: Electrical Components, Motors, and Schematics

3.1 Contactors, Relays, Switches, Overload Protection, and Thermostats 3.2 HVAC Motors (PSC, CSIR, CSCR, ECM, 3-Phase) and Run/Start Capacitors 3.3 Interpreting Ladder Diagrams, Schematics, and Point-to-Point Wiring 3.4 Motor Testing, Insulation Resistance, Bearings, and Belt Drives

4 Chapter 4: Thermodynamics and the Refrigeration Cycle

4.1 Heat Transfer, Temperature Scales, BTUs, Sensible vs Latent Heat, and Enthalpy 4.2 The Four Vapor-Compression Cycle Stages (Compression, Condensation, Expansion, Evaporation) 4.3 P-T Charts, Saturated Conditions, Target Superheat, and Subcooling Calculations 4.4 Pressure–Enthalpy Diagrams, Compression Ratio, and Cycle Analysis

5 Chapter 5: Refrigerants, Environmental Regulations, and Recovery

5.1 Refrigerant Types (CFC, HCFC, HFC, HFO, HC) and ASHRAE Safety Groups (A1, A2L, A3) 5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards 5.3 Recovery/Recycling/Reclaiming Equipment, Procedures, and Leak Detection 5.4 Refrigerant Retrofits, Cylinder Handling, and Refrigerant Purity 5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice

6 Chapter 6: Refrigeration System Components and Accessories

6.1 Compressor Mechanics (Reciprocating, Scroll, Rotary, Screw) and Failures 6.2 Expansion Devices (TXV/TEV, Fixed Orifice, EEV) and Superheat Control 6.3 Condensers, Evaporators, Filter-Driers, Accumulators, Receivers, and Solenoids 6.4 Pressure Controls, Capacity Controls, and System Protection 6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice

7 Chapter 7: Gas Heating, Combustion Analysis, and Fuel Piping

7.1 Combustion Theory, Fuel Gases (Natural Gas vs LP), and Gas Burners 7.2 Gas Valves, Ignition Systems (Standing Pilot, Spark, HSI), and Safety Limit Controls 7.3 Flue Venting, Draft Principles, Combustion Analysis, and CO Safety 7.4 Fuel-Gas and Oil Piping, Vent System Selection and Sizing, and Installation Practice

8 Chapter 8: Electric Heating, Oil Heat, and Hydronics

8.1 Electric Heating Elements, Sequencers, Limit Switches, and kW Calculations 8.2 Oil Burners, Fuel Pumps, Nozzles, Ignition Electrodes, and Primary Controls 8.3 Hydronic Boilers, Circulator Pumps, Expansion Tanks, and Zone Controls 8.4 Combustion Air, Water Heaters, and Combustion Appliance Zone Testing

9 Chapter 9: Heat Pumps and Dual-Fuel Systems

9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation 9.2 Defrost Controls (Time-Temperature, Demand Defrost), Sensors, and Sequences 9.3 Balance Points, Auxiliary/Emergency Heat, and Dual-Fuel (Hybrid) Systems 9.4 Heat Pump Diagnostics, Refrigerant Flow, and Troubleshooting Procedures 9.5 Heat Pump Types, Cold-Climate Performance, and Sizing Approaches

10 Chapter 10: Air Distribution, IAQ, and System Commissioning

10.1 Airflow Fundamentals, CFM Measurement, External Static Pressure, and Fan Laws 10.2 Duct Sizing Principles, Supply/Return Distribution, Dampers, and Air Balancing 10.3 Indoor Air Quality, MERV Ratings, Electronic Cleaners, Humidification, and Dehumidification 10.4 Deep Vacuum Evacuation (Micron Gauge), Subcooling/Superheat Charging, and System Commissioning 10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance

11 Chapter 11: Psychrometrics, Airside Calculations, and Load Estimation

11.1 Reading the Psychrometric Chart: Properties and Plotting 11.2 The Eight Air-Conditioning Processes and the Process Triangle 11.3 Mixed Air, Ventilation, and Infiltration Calculations 11.4 Residential Heat Loss, Heat Gain, and Equipment Sizing

12 Chapter 12: Light Commercial Air Conditioning

12.1 Packaged Rooftop and Split Light-Commercial Systems 12.2 Water-Cooled Condensers, Cooling Towers, and Chilled-Water Systems 12.3 Economizers, Demand-Controlled Ventilation, and VAV Air Distribution 12.4 Light-Commercial Start-Up, Commissioning, and Troubleshooting

13 Chapter 13: Light Commercial Refrigeration

13.1 Temperature Ranges, Box Loads, and Refrigeration System Types 13.2 Evaporators, Defrost Methods, and Defrost Controls 13.3 Condensing Units, Parallel Racks, Oil Management, and Capacity Control 13.4 Refrigeration Control Valves and Automatic Pump-Down 13.5 Commercial Refrigeration Diagnostics and Ice Machines

14 Chapter 14: Ductless, Mini-Split, and VRF Systems

14.1 Mini-Split Architecture and Inverter-Driven Compressors 14.2 Multi-Zone and VRF Operation, Electronic Expansion Valves, and Controls 14.3 Ductless Installation, Evacuation, Charging, and Diagnostics

15 Chapter 15: Building Automation and Digital Controls

15.1 DDC Fundamentals, Control Loops, and Sequences of Operation 15.2 BAS Networks, Protocols, and NEC-Compliant Cabling 15.3 Building Automation Controllers: Supervisory, Field, and Room Devices 15.4 Digital Logic, Numbering Systems, and Controller Programming 15.5 Sensor Selection, Installation, and Input Point Configuration 15.6 Actuators, Output Devices, and VFD Integration 15.7 Commercial Prints, Equipment Schedules, and BAS Documentation

1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs

Key Takeaways Explain This Topic AI

The Competency and Task List's General Studies sheet requires knowing HVACR industry organizations, energy resources, energy efficiency ratings, renewable versus sustainable energy, life cycle cost analysis, and energy auditing.

ECM appears twice on the task list with two different meanings - Energy Conservation Measure and Electronically Commutated Motor - and context is the only way to tell them apart.

SEER2, EER2, and HSPF2 come from the DOE M1 test procedure effective January 1, 2023, which tests at 0.5 in. w.c. external static pressure instead of the 0.1 in. w.c. used for the older ratings.

COP is a unitless ratio of output to input in the same units, and COP equals EER divided by 3.412.

ASHRAE defines three energy audit levels: Level 1 walk-through, Level 2 energy survey and analysis, and Level 3 detailed analysis of capital-intensive modifications.

Last updated: August 2026

1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs

The General Studies sheet of the HVAC Excellence Competency and Task List opens with mathematics (Section 1.4) and then moves to a block titled HVACR General Studies . That block requires knowledge of:

  • HVACR industry organizations
  • Energy resources and energy efficiency ratings
  • Defining and differentiating between Renewable and Sustainable energy
  • Life Cycle Cost Analysis
  • Energy auditing

A named list of acronyms: BIM, CBECS, ECM, EIA, EER, SEER, SEER2, AFUE, HSPF, HSPF2, USGBC, GBI, LEED, COP, ECM (again), DOE

This is the general-knowledge material every Professional Level candidate is expected to carry, and it is the part of the syllabus most prep material skips entirely.

1. HVACR Industry Organizations

A technician is expected to know who writes what, because "per code" means different documents depending on which organization is being cited.

Standards-writing and technical societies

Organization Full name What it produces

ASHRAE American Society of Heating, Refrigerating and Air-Conditioning Engineers Standards 15, 34, 55, 62.1, 62.2, 90.1, 135 (BACnet), 189.1; the Handbook series

AHRI Air-Conditioning, Heating, and Refrigeration Institute Equipment performance certification and rating standards; the AHRI Directory of matched system ratings; AHRI 700 refrigerant purity

ACCA Air Conditioning Contractors of America Manual J (load), Manual S (equipment selection), Manual D (duct design), Manual T , Manual B ; contractor standards

SMACNA Sheet Metal and Air Conditioning Contractors' National Association Duct construction standards, HVAC duct leakage test manual, seismic restraint

  • RSES Refrigeration Service Engineers Society Technician training and certification; service literature
  • NADCA National Air Duct Cleaners Association Duct cleaning standards (ACR)

BPI / RESNET Building Performance Institute / Residential Energy Services Network Building-science and home energy rating credentials; HERS Index

AABC / NEBB / TABB Testing and balancing certifying bodies Air and water balancing procedures and certification

Code and safety bodies

Organization Documents that govern HVACR work

ICC (International Code Council) IMC (Mechanical), IFGC (Fuel Gas), IRC (Residential), IECC (Energy Conservation), IBC

NFPA (National Fire Protection Association) NFPA 54 / ANSI Z223.1 National Fuel Gas Code; NFPA 58 LP-Gas Code; NFPA 31 Oil-Burning Equipment; NFPA 70 National Electrical Code

UL / CSA Product safety listing — UL 60335-2-40 (A2L equipment), UL 1738 (special gas vents), UL 181 (duct closure)

  • ANSI Accredits and publishes consensus standards
  • Government agencies

Agency Role in HVACR

DOE (Department of Energy) Sets minimum federal appliance efficiency standards and the test procedures behind SEER2/HSPF2/AFUE

EPA (Environmental Protection Agency) Section 608 technician certification and refrigerant rules; SNAP ; AIM Act HFC phasedown; ENERGY STAR (with DOE)

EIA (Energy Information Administration) The statistical arm of DOE — collects and publishes energy data, including CBECS and RECS

OSHA Workplace safety standards (Section 1.5)

PNNL (Pacific Northwest National Laboratory) A DOE national laboratory. The competencies marked with an asterisk on the task list were contributed by PNNL and focus on heat pumps, electrification, and sizing

  • FTC The yellow EnergyGuide label on residential equipment
  • Certifying and workforce organizations

HVAC Excellence (a member of the ESCO Group ) and NATE (North American Technician Excellence) are the two dominant voluntary technician certification bodies. The United Association (UA) and MCAA/MSCA represent the organized-labor and mechanical-contractor sides of the workforce, and both have articulation agreements with HVAC Excellence (Section 1.1).

2. Energy Resources

Primary energy sources are grouped as:

  • Category Sources
  • Fossil fuels (non-renewable) Coal, natural gas, petroleum (including fuel oil and propane)
  • Nuclear (non-renewable) Uranium fission
  • Renewable Solar, wind, hydro, geothermal, biomass

Site energy versus source energy is the distinction that decides arguments about heat pumps versus furnaces:

Site energy is what the building's meters record — the therms and kilowatt-hours delivered.

Source energy (primary energy) adds the energy consumed in generating and delivering that energy, including power-plant conversion losses and transmission losses.

A kilowatt-hour of electricity carries a much larger source-energy burden than its site value, because roughly two-thirds of the fuel energy at a conventional thermal power plant is rejected as heat. ENERGY STAR Portfolio Manager scores buildings on source energy precisely so that electric and fossil-fueled buildings can be compared fairly. This is also why a heat pump with a COP above about 3 can beat a condensing furnace on source energy while a resistance heater with a COP of 1.0 never can.

3. Renewable Versus Sustainable — Not Synonyms

The task list asks for this distinction explicitly.

  • Renewable Sustainable
  • What it describes The resource The practice

Definition Replenished naturally on a human timescale Meeting present needs without compromising the ability of future generations to meet theirs (the Brundtland definition)

Test Does it run out? Can it continue indefinitely without net harm?

A renewable resource can be used unsustainably. Biomass is renewable, but harvesting a forest faster than it regrows is not sustainable. Groundwater-source heat pumps draw on a renewable resource, but depleting an aquifer faster than it recharges is not sustainable.

A practice can be sustainable without being renewable. Recovering, reclaiming, and reusing refrigerant does not make R-410A renewable, but it substantially reduces the environmental burden of keeping existing equipment running — which is why the EPA rules of Chapter 5 exist.

4. Energy Efficiency Ratings

The task list names eight ratings by acronym. Know what each measures, and — critically — what it does not .

  • Rating Full name Measures Units
  • EER / EER2 Energy Efficiency Ratio Cooling efficiency at one rated condition (95°F outdoor) Btu/h per watt
  • SEER / SEER2 Seasonal Energy Efficiency Ratio Cooling efficiency over a simulated season Btu per watt-hour

HSPF / HSPF2 Heating Seasonal Performance Factor Heat pump heating efficiency over a simulated season Btu per watt-hour

  • COP Coefficient of Performance Output ÷ input, same units both sides Unitless
  • AFUE Annual Fuel Utilization Efficiency Percentage of fuel energy delivered as useful heat over a season %
  • IEER Integrated Energy Efficiency Ratio Part-load cooling efficiency of commercial equipment Btu/h per watt
  • UEF Uniform Energy Factor Water heater efficiency Unitless
  • MERV Minimum Efficiency Reporting Value Filter particle capture , not energy (Section 10.3) 1–16

The conversion the exam asks for. Because COP is unitless and EER is in Btu/h per watt, and 1 watt = 3.412 Btu/h: C O P = E E R 3.412 E E R = C O P × 3.412 COP = \frac{EER}{3.412} \qquad EER = COP \times 3.412 COP = 3.412 EER ​ EER = COP × 3.412

A unit rated 12.0 EER has a COP of 12.0 ÷ 3.412 = 3.52 12.0 \div 3.412 = 3.52 12.0 ÷ 3.412 = 3.52 — for every unit of electrical energy in, 3.52 units of heat energy are moved.

Why the "2" ratings exist. On January 1, 2023 , DOE's M1 test procedure took effect. The new procedure tests residential equipment at 0.5 in. w.c. external static pressure instead of the 0.1 in. w.c. used previously — a far more realistic representation of a real duct system. Because the fan works harder in the test, the numeric rating drops for the same physical equipment . SEER2 values run roughly 4.5% below the SEER value of the same unit, and HSPF2 roughly 15% below HSPF. A 15 SEER unit did not become less efficient; it is now rated about 14.3 SEER2.

Current federal minimums (split systems, effective January 1, 2023):

  • Product North Southeast / Southwest
  • Split AC, < 45,000 Btu/h 13.4 SEER2 14.3 SEER2
  • Split AC, ≥ 45,000 Btu/h 13.4 SEER2 13.8 SEER2
  • Split heat pump (national) 14.3 SEER2 / 7.5 HSPF2 14.3 SEER2 / 7.5 HSPF2

Furnaces. The current federal minimum for a non-weatherized gas furnace is 80% AFUE . DOE's 2023 final rule raises that to 95% AFUE for units manufactured on or after December 18, 2028 , which would end non-condensing residential gas furnaces. The rule has been in continuous litigation; in June 2026 the Supreme Court vacated the D.C. Circuit's decision upholding it and remanded the case, and DOE has proposed delaying the compliance date. The rule remains in effect while the case is reconsidered. Verify the current compliance date before quoting it to a customer — this is exactly the kind of fact that changes between exam revisions.

5. The Acronym List — Including the One That Means Two Things

Acronym Expansion Note

BIM Building Information Modeling A 3D model carrying data — dimensions, equipment attributes, maintenance records — not just geometry. Used for clash detection (finding the duct that runs through a beam before it is fabricated) and handed over as an asset database

CBECS Commercial Buildings Energy Consumption Survey EIA's national survey of commercial building characteristics and energy use. Its residential counterpart is RECS

ECM Energy Conservation Measure A specific efficiency improvement identified in an audit — a VFD retrofit, an economizer repair, added insulation

ECM Electronically Commutated Motor The brushless DC motor of Section 3.2

EIA Energy Information Administration The statistical agency within DOE; publishes CBECS, RECS, and the Annual Energy Outlook

USGBC U.S. Green Building Council The non-profit that developed and administers LEED

LEED Leadership in Energy and Environmental Design USGBC's rating system; certification levels Certified, Silver, Gold, Platinum

  • GBI Green Building Initiative Administers Green Globes , an alternative green-building rating system
  • DOE U.S. Department of Energy Sets appliance efficiency standards; parent of EIA and the national laboratories

The ECM collision is a genuine exam trap , and it is on the task list twice for that reason. In an energy-audit sentence, ECM is a conservation measure; in a blower or wiring sentence, ECM is the motor. Context is the only discriminator.

6. Life Cycle Cost Analysis

Simple payback is the number most customers ask for: Simple payback (years) = Incremental first cost Annual savings \text{Simple payback (years)} = \frac{\text{Incremental first cost}}{\text{Annual savings}} Simple payback (years) = Annual savings Incremental first cost ​

A high-efficiency unit costing $2,400 more that saves $400 per year has a 6-year simple payback . Simple payback ignores the time value of money, maintenance differences, equipment life, and salvage value — which is why it is a screening tool, not a decision tool.

Life Cycle Cost Analysis (LCCA) totals every cost over the study period, discounted to present value: L C C = Initial + Energy + Maintenance + Repair + Replacement − Salvage LCC = \text{Initial} + \text{Energy} + \text{Maintenance} + \text{Repair} + \text{Replacement} - \text{Salvage} L CC = Initial + Energy + Maintenance + Repair + Replacement − Salvage

The federal methodology is NIST Handbook 135 , implemented in DOE's BLCC software.

Why LCCA changes answers. Two rooftop units:

  • Unit A Unit B
  • First cost $9,000 $13,000
  • Annual energy $3,100 $2,250
  • Annual maintenance $550 $400
  • Expected life 12 years 18 years

Unit A wins on first cost by $4,000 and loses on annual operating cost by $1,000. Simple payback on the upgrade is 4 years — but LCCA also captures that Unit A must be replaced six years sooner , and that replacement cost dominates the comparison over an 18-year study period. This is the analysis behind every "the cheap one costs more" conversation.

Commercial rate structures matter here too. Commercial customers pay an energy charge ($/kWh) and a demand charge ($/kW based on the highest 15- or 30-minute average demand in the billing period). A measure that shaves peak demand — staging, demand limiting, a VFD — can save money out of proportion to its kWh reduction, and an LCCA that models only kWh will undervalue it.

7. Energy Auditing

An energy audit identifies where a building uses energy and what can cost-effectively be done about it. ASHRAE defines three levels , and the level determines the cost, the rigor, and what the deliverable is good for:

Level Name Work performed Deliverable

Level 1 Walk-through analysis Utility bill review, brief site visit, benchmarking Low-cost/no-cost measures and a list of potential capital measures

Level 2 Energy survey and analysis Detailed survey, breakdown of energy use by system, savings and cost estimates for each measure ECMs with savings, cost, and payback the owner can act on

Level 3 Detailed analysis of capital-intensive modifications Field measurement, monitoring, and calibrated modeling of the major measures Investment-grade analysis suitable for large capital decisions

Benchmarking comes first. EUI (Energy Use Intensity) normalizes consumption by floor area: E U I = Annual energy use (kBtu) Gross floor area (ft 2 ) EUI = \frac{\text{Annual energy use (kBtu)}}{\text{Gross floor area (ft}^2\text{)}} E U I = Gross floor area (ft 2 ) Annual energy use (kBtu) ​

A 40,000 ft² office consuming 3,200 MMBtu per year has an EUI of 3,200,000 ÷ 40,000 = 80 3{,}200{,}000 \div 40{,}000 = 80 3 , 200 , 000 ÷ 40 , 000 = 80 kBtu/ft²/yr. Compared against the CBECS median for that building type, that number says immediately whether there is anything worth auditing.

What the HVACR technician contributes to an audit is exactly the measurement skill set the rest of this guide teaches: airflow and static pressure (Section 10.1), duct leakage and blower door results (Section 10.5), combustion efficiency and CO (Section 7.3), refrigerant charge verification (Section 10.4), temperature split, motor amperage and power factor, and control sequence verification (Chapter 15). An audit report without measured data is a sales brochure.

Green building programs provide the certification framework these measures roll up into: LEED from USGBC, Green Globes from GBI, ENERGY STAR certification from EPA/DOE, and ASHRAE Standard 189.1 / the IgCC as code-intended green construction standards.