Study guide
12.1 Packaged Rooftop and Split Light-Commercial Systems
HVAC Excellence Certification Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction, Safety, Tools, and Diagnostic Method
1.1 HVAC Excellence Certification, Industry Codes, and Standards 1.2 Electrical Safety, PPE, Lockout/Tagout, and Hazard Communication 1.3 Multimeters, Manifold Gauges, Micron Gauges, and Diagnostic Instruments 1.4 HVACR Mathematics, Unit Conversions, and Efficiency Ratings 1.5 OSHA Standards, Fall Protection, Rigging, and Confined Spaces 1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs 1.7 Systematic Troubleshooting: Data Plates, Manufacturer Literature, and Diagnostic Method
2 Chapter 2: Electrical Fundamentals and Circuit Theory
2.1 Voltage, Current, Resistance, and Ohm's Law Calculations 2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations 2.3 AC Fundamentals, Single-Phase vs Three-Phase Power, and Control Transformers 2.4 Conductors, Insulators, Wire Sizing, Voltage Drop, and NEC Ampacity
3 Chapter 3: Electrical Components, Motors, and Schematics
3.1 Contactors, Relays, Switches, Overload Protection, and Thermostats 3.2 HVAC Motors (PSC, CSIR, CSCR, ECM, 3-Phase) and Run/Start Capacitors 3.3 Interpreting Ladder Diagrams, Schematics, and Point-to-Point Wiring 3.4 Motor Testing, Insulation Resistance, Bearings, and Belt Drives
4 Chapter 4: Thermodynamics and the Refrigeration Cycle
4.1 Heat Transfer, Temperature Scales, BTUs, Sensible vs Latent Heat, and Enthalpy 4.2 The Four Vapor-Compression Cycle Stages (Compression, Condensation, Expansion, Evaporation) 4.3 P-T Charts, Saturated Conditions, Target Superheat, and Subcooling Calculations 4.4 Pressure–Enthalpy Diagrams, Compression Ratio, and Cycle Analysis
5 Chapter 5: Refrigerants, Environmental Regulations, and Recovery
5.1 Refrigerant Types (CFC, HCFC, HFC, HFO, HC) and ASHRAE Safety Groups (A1, A2L, A3) 5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards 5.3 Recovery/Recycling/Reclaiming Equipment, Procedures, and Leak Detection 5.4 Refrigerant Retrofits, Cylinder Handling, and Refrigerant Purity 5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice
6 Chapter 6: Refrigeration System Components and Accessories
6.1 Compressor Mechanics (Reciprocating, Scroll, Rotary, Screw) and Failures 6.2 Expansion Devices (TXV/TEV, Fixed Orifice, EEV) and Superheat Control 6.3 Condensers, Evaporators, Filter-Driers, Accumulators, Receivers, and Solenoids 6.4 Pressure Controls, Capacity Controls, and System Protection 6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice
7 Chapter 7: Gas Heating, Combustion Analysis, and Fuel Piping
7.1 Combustion Theory, Fuel Gases (Natural Gas vs LP), and Gas Burners 7.2 Gas Valves, Ignition Systems (Standing Pilot, Spark, HSI), and Safety Limit Controls 7.3 Flue Venting, Draft Principles, Combustion Analysis, and CO Safety 7.4 Fuel-Gas and Oil Piping, Vent System Selection and Sizing, and Installation Practice
8 Chapter 8: Electric Heating, Oil Heat, and Hydronics
8.1 Electric Heating Elements, Sequencers, Limit Switches, and kW Calculations 8.2 Oil Burners, Fuel Pumps, Nozzles, Ignition Electrodes, and Primary Controls 8.3 Hydronic Boilers, Circulator Pumps, Expansion Tanks, and Zone Controls 8.4 Combustion Air, Water Heaters, and Combustion Appliance Zone Testing
9 Chapter 9: Heat Pumps and Dual-Fuel Systems
9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation 9.2 Defrost Controls (Time-Temperature, Demand Defrost), Sensors, and Sequences 9.3 Balance Points, Auxiliary/Emergency Heat, and Dual-Fuel (Hybrid) Systems 9.4 Heat Pump Diagnostics, Refrigerant Flow, and Troubleshooting Procedures 9.5 Heat Pump Types, Cold-Climate Performance, and Sizing Approaches
10 Chapter 10: Air Distribution, IAQ, and System Commissioning
10.1 Airflow Fundamentals, CFM Measurement, External Static Pressure, and Fan Laws 10.2 Duct Sizing Principles, Supply/Return Distribution, Dampers, and Air Balancing 10.3 Indoor Air Quality, MERV Ratings, Electronic Cleaners, Humidification, and Dehumidification 10.4 Deep Vacuum Evacuation (Micron Gauge), Subcooling/Superheat Charging, and System Commissioning 10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance
11 Chapter 11: Psychrometrics, Airside Calculations, and Load Estimation
11.1 Reading the Psychrometric Chart: Properties and Plotting 11.2 The Eight Air-Conditioning Processes and the Process Triangle 11.3 Mixed Air, Ventilation, and Infiltration Calculations 11.4 Residential Heat Loss, Heat Gain, and Equipment Sizing
12 Chapter 12: Light Commercial Air Conditioning
12.1 Packaged Rooftop and Split Light-Commercial Systems 12.2 Water-Cooled Condensers, Cooling Towers, and Chilled-Water Systems 12.3 Economizers, Demand-Controlled Ventilation, and VAV Air Distribution 12.4 Light-Commercial Start-Up, Commissioning, and Troubleshooting
13 Chapter 13: Light Commercial Refrigeration
13.1 Temperature Ranges, Box Loads, and Refrigeration System Types 13.2 Evaporators, Defrost Methods, and Defrost Controls 13.3 Condensing Units, Parallel Racks, Oil Management, and Capacity Control 13.4 Refrigeration Control Valves and Automatic Pump-Down 13.5 Commercial Refrigeration Diagnostics and Ice Machines
14 Chapter 14: Ductless, Mini-Split, and VRF Systems
14.1 Mini-Split Architecture and Inverter-Driven Compressors 14.2 Multi-Zone and VRF Operation, Electronic Expansion Valves, and Controls 14.3 Ductless Installation, Evacuation, Charging, and Diagnostics
15 Chapter 15: Building Automation and Digital Controls
15.1 DDC Fundamentals, Control Loops, and Sequences of Operation 15.2 BAS Networks, Protocols, and NEC-Compliant Cabling 15.3 Building Automation Controllers: Supervisory, Field, and Room Devices 15.4 Digital Logic, Numbering Systems, and Controller Programming 15.5 Sensor Selection, Installation, and Input Point Configuration 15.6 Actuators, Output Devices, and VFD Integration 15.7 Commercial Prints, Equipment Schedules, and BAS Documentation
12.1 Packaged Rooftop and Split Light-Commercial Systems
Key Takeaways Explain This Topic AI
Light commercial air conditioning is a distinct HVAC Excellence Professional Level exam covering commercial systems and components, installation, service, theory, applications, and troubleshooting.
Most light commercial equipment runs on three-phase power, so a three-phase compressor can be started in the wrong rotation and will run backward with low amp draw and no pressure differential.
Rooftop units typically stage two or more compressors or use a digital scroll, and staging must be verified against the thermostat or controller sequence during commissioning.
Curb and roof-penetration details matter: an improperly flashed curb or a supply-return short circuit inside the curb produces performance complaints no refrigeration work will fix.
Commercial equipment carries a rated external static pressure, often 0.50 to 1.00 inches of water column, far above residential values, and airflow must be verified against that rating.
Last updated: August 2026
12.1 Packaged Rooftop and Split Light-Commercial Systems
Light Commercial Air Conditioning is one of the ten HVAC Excellence Professional Level written exams, and its competency sheet is the second-largest in the entire task list. The published description covers "commercial AC systems and components, installation, service, theory, applications, and troubleshooting."
Everything in Chapters 4 through 6 still applies — the refrigeration cycle does not change with the size of the box. What changes is the electrical service, the control complexity, the airside requirements, and the consequences of failure .
1. Equipment Families
Type Description Typical size
Packaged rooftop unit (RTU) Compressor, condenser, evaporator, blower, filters, and often heat in one cabinet on a roof curb 3–25 tons
Split system Outdoor condensing unit plus indoor air handler, joined by field-installed line sets 3–20 tons
Self-contained / vertical package All components in an indoor cabinet with a water-cooled condenser or ducted outdoor air 5–30 tons
Water-source heat pump Distributed units on a common building water loop, tempered by a boiler and a cooling tower 0.5–5 tons each
Split-system heat pump / VRF Inverter-driven, multiple indoor units (Chapter 14) Wide range
The rooftop packaged unit dominates light commercial work: retail, restaurants, small offices, schools. Its advantages are a single point of service, no indoor mechanical room, and factory-assembled refrigeration. Its disadvantages are exposure to weather, difficult access, and the fact that a curb or duct problem is nearly invisible from the ground.
2. Three-Phase Power in the Field
Almost all commercial equipment above about 5 tons is three-phase. Section 2.3 covered the theory; this is what changes at the unit.
Common services
208/120 V wye, 4-wire — the most common in small commercial buildings.
480/277 V wye, 4-wire — larger buildings; 277 V feeds lighting and the control transformer.
240 V delta, 4-wire with a high leg (wild leg) — a legacy service. The high leg measures about 208 V to neutral rather than 120 V, must be marked orange , and must land on phase B in the panel. Connecting a 120 V control transformer to the high leg destroys it instantly.
Rotation
A three-phase motor will start and run in either direction depending on phase sequence. Two consequences:
Scroll and screw compressors are direction-sensitive. Run backward, a scroll makes a loud rattle or growl, draws noticeably low amperage , and develops little or no pressure differential . Left running, it will be damaged within minutes. The fix is to swap any two line conductors at the disconnect.
Blowers and condenser fans move air backward — reduced airflow, wrong direction, and a distinctive lack of discharge velocity.
Commissioning rule: on any new three-phase installation or after any utility or panel work, verify rotation before extended operation — with a phase-rotation meter if available, and always by confirming that suction pressure falls and discharge pressure rises within seconds of start.
Voltage imbalance
Re-check the 2% limit from Section 2.4. Commercial services with large single-phase loads (lighting, receptacles) are more prone to imbalance than residential services, and a three-phase compressor is far less tolerant of it than a single-phase one.
3. Multiple Compressors and Staging
Light commercial units rarely have one fixed-capacity compressor.
Arrangement How it works
Two independent circuits Two compressors, two coils (or a split-face coil), two metering devices. Stage 1 and Stage 2 are electrically and refrigerantly separate.
Tandem compressors Two compressors piped to a common suction and discharge manifold serving one circuit; requires oil equalization lines.
Digital scroll One compressor whose scroll plates separate on a duty cycle, giving continuous modulation from roughly 10% to 100%.
Variable frequency drive Speed modulation of a standard compressor.
Unloaders Semi-hermetic reciprocating compressors hold suction valves open on selected cylinders.
Staging control comes from a two-stage thermostat, a multistage electronic controller, or the building automation system. Commissioning must verify that stage 2 actually energizes on a call, that the anti-short-cycle timer and minimum on/off times are functioning, and on tandem systems that oil is equalizing — an unequal oil level between two manifolded compressors starves one and floods the other.
4. Airside: Curb, Ductwork, and Static Pressure
The most common cause of a "not cooling" complaint on a rooftop unit is not refrigeration.
Roof curb. The curb is a fabricated frame that supports the unit, provides the supply and return duct transitions, and terminates the roofing membrane. Failure modes:
Missing or compressed gasket between unit and curb — outdoor air is drawn into the return or conditioned air escapes.
Supply-to-return short circuit inside the curb — the divider is missing, misaligned, or has failed. Supply air recirculates directly into the return, and the unit produces a small temperature split with normal refrigerant pressures. Diagnose by comparing the temperature at the diffuser to the temperature at the unit's supply outlet.
Improper flashing — the leak shows up as ceiling damage months later.
External static pressure. Commercial equipment carries a rated ESP , commonly 0.50 to 1.00 in. w.c. — far above the 0.50 in. w.c. total that residential equipment is designed around. Measure total external static across the unit and compare it to the fan performance table, then use the table to determine actual CFM at that static and the measured motor speed or drive setting. Commercial rooftops frequently use belt-drive blowers whose sheaves are adjusted at commissioning (Section 3.4).
Airflow per ton. Comfort cooling still targets roughly 350–450 CFM per ton , and 400 CFM/ton is the usual design point. Applications with a high sensible load (retail with heavy lighting) may design higher; restaurants and other high-latent spaces design lower.
Filtration. Commercial units use 2- or 4-inch pleated filters and sometimes filter banks. A clogged filter bank on a belt-drive unit reduces airflow, drops coil temperature, and eventually freezes the evaporator — the same failure chain as residential, but with more static pressure available to disguise it until it is severe.
5. Components You Will Meet Only on Commercial Equipment
The Commercial Air Conditioning sheet names a specific list; several appear nowhere in residential work.
Oil separator — mounted in the discharge line, it removes oil from the hot gas stream and returns it directly to the crankcase through a float valve. Used where long line runs, low ambient operation, or multiple evaporators make normal oil return unreliable.
Crankcase heater — mandatory on most commercial compressors (Section 6.4).
Vibration eliminator — a flexible braided-metal section in the suction and discharge lines that prevents compressor vibration from work-hardening and cracking the piping. Install parallel to the crankshaft and never stretch or compress it.
Sight glass with moisture indicator — bubbles indicate flash gas from undercharge or restriction; the color ring indicates moisture (green = dry, yellow = wet).
Receiver — stores liquid refrigerant, required on TXV systems with flooding head pressure control (Section 6.4).
Suction accumulator — protects against liquid floodback on heat pumps and low-temperature systems.
Head Master / low ambient control , hot gas bypass , EPR , oil pressure safety control , lockout relay — all covered in Section 6.4.
Economizer — an outdoor-air damper section with controls (Section 12.3).
Refrigerant distributor and feeder tubes — a venturi-type distributor downstream of the TXV splits liquid evenly among multiple evaporator circuits. It must be installed vertically down where possible, with equal-length feeder tubes; unequal feeders produce uneven circuit loading, and one starved circuit raises system superheat while another floods.
Auxiliary heat exchanger / subcooler — adds liquid subcooling to overcome long-line or high-lift pressure drop (Section 6.5).
6. Service Access and Roof Safety
Fall protection applies (Section 1.5). Many roofs have no parapet, and a unit set close to the edge creates an immediate hazard.
Ladder access must be secured, at a 4:1 pitch, with 3 feet of extension above the roof edge.
Disconnect must be within sight of the unit (Section 1.1, NEC 440.14). On a roof this often means a disconnect mounted on the unit itself or on a nearby stanchion.
Lockout/tagout on a roof is easy to skip and dangerous to skip: the panel is usually far away and out of sight, and a building engineer may reset a breaker without knowing anyone is on the roof.
Convenience receptacle and lighting are required by the IMC for equipment on roofs and in attics, and their absence is a code violation worth documenting.