Study guide
13.1 Temperature Ranges, Box Loads, and Refrigeration System Types
HVAC Excellence Certification Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction, Safety, Tools, and Diagnostic Method
1.1 HVAC Excellence Certification, Industry Codes, and Standards 1.2 Electrical Safety, PPE, Lockout/Tagout, and Hazard Communication 1.3 Multimeters, Manifold Gauges, Micron Gauges, and Diagnostic Instruments 1.4 HVACR Mathematics, Unit Conversions, and Efficiency Ratings 1.5 OSHA Standards, Fall Protection, Rigging, and Confined Spaces 1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs 1.7 Systematic Troubleshooting: Data Plates, Manufacturer Literature, and Diagnostic Method
2 Chapter 2: Electrical Fundamentals and Circuit Theory
2.1 Voltage, Current, Resistance, and Ohm's Law Calculations 2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations 2.3 AC Fundamentals, Single-Phase vs Three-Phase Power, and Control Transformers 2.4 Conductors, Insulators, Wire Sizing, Voltage Drop, and NEC Ampacity
3 Chapter 3: Electrical Components, Motors, and Schematics
3.1 Contactors, Relays, Switches, Overload Protection, and Thermostats 3.2 HVAC Motors (PSC, CSIR, CSCR, ECM, 3-Phase) and Run/Start Capacitors 3.3 Interpreting Ladder Diagrams, Schematics, and Point-to-Point Wiring 3.4 Motor Testing, Insulation Resistance, Bearings, and Belt Drives
4 Chapter 4: Thermodynamics and the Refrigeration Cycle
4.1 Heat Transfer, Temperature Scales, BTUs, Sensible vs Latent Heat, and Enthalpy 4.2 The Four Vapor-Compression Cycle Stages (Compression, Condensation, Expansion, Evaporation) 4.3 P-T Charts, Saturated Conditions, Target Superheat, and Subcooling Calculations 4.4 Pressure–Enthalpy Diagrams, Compression Ratio, and Cycle Analysis
5 Chapter 5: Refrigerants, Environmental Regulations, and Recovery
5.1 Refrigerant Types (CFC, HCFC, HFC, HFO, HC) and ASHRAE Safety Groups (A1, A2L, A3) 5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards 5.3 Recovery/Recycling/Reclaiming Equipment, Procedures, and Leak Detection 5.4 Refrigerant Retrofits, Cylinder Handling, and Refrigerant Purity 5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice
6 Chapter 6: Refrigeration System Components and Accessories
6.1 Compressor Mechanics (Reciprocating, Scroll, Rotary, Screw) and Failures 6.2 Expansion Devices (TXV/TEV, Fixed Orifice, EEV) and Superheat Control 6.3 Condensers, Evaporators, Filter-Driers, Accumulators, Receivers, and Solenoids 6.4 Pressure Controls, Capacity Controls, and System Protection 6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice
7 Chapter 7: Gas Heating, Combustion Analysis, and Fuel Piping
7.1 Combustion Theory, Fuel Gases (Natural Gas vs LP), and Gas Burners 7.2 Gas Valves, Ignition Systems (Standing Pilot, Spark, HSI), and Safety Limit Controls 7.3 Flue Venting, Draft Principles, Combustion Analysis, and CO Safety 7.4 Fuel-Gas and Oil Piping, Vent System Selection and Sizing, and Installation Practice
8 Chapter 8: Electric Heating, Oil Heat, and Hydronics
8.1 Electric Heating Elements, Sequencers, Limit Switches, and kW Calculations 8.2 Oil Burners, Fuel Pumps, Nozzles, Ignition Electrodes, and Primary Controls 8.3 Hydronic Boilers, Circulator Pumps, Expansion Tanks, and Zone Controls 8.4 Combustion Air, Water Heaters, and Combustion Appliance Zone Testing
9 Chapter 9: Heat Pumps and Dual-Fuel Systems
9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation 9.2 Defrost Controls (Time-Temperature, Demand Defrost), Sensors, and Sequences 9.3 Balance Points, Auxiliary/Emergency Heat, and Dual-Fuel (Hybrid) Systems 9.4 Heat Pump Diagnostics, Refrigerant Flow, and Troubleshooting Procedures 9.5 Heat Pump Types, Cold-Climate Performance, and Sizing Approaches
10 Chapter 10: Air Distribution, IAQ, and System Commissioning
10.1 Airflow Fundamentals, CFM Measurement, External Static Pressure, and Fan Laws 10.2 Duct Sizing Principles, Supply/Return Distribution, Dampers, and Air Balancing 10.3 Indoor Air Quality, MERV Ratings, Electronic Cleaners, Humidification, and Dehumidification 10.4 Deep Vacuum Evacuation (Micron Gauge), Subcooling/Superheat Charging, and System Commissioning 10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance
11 Chapter 11: Psychrometrics, Airside Calculations, and Load Estimation
11.1 Reading the Psychrometric Chart: Properties and Plotting 11.2 The Eight Air-Conditioning Processes and the Process Triangle 11.3 Mixed Air, Ventilation, and Infiltration Calculations 11.4 Residential Heat Loss, Heat Gain, and Equipment Sizing
12 Chapter 12: Light Commercial Air Conditioning
12.1 Packaged Rooftop and Split Light-Commercial Systems 12.2 Water-Cooled Condensers, Cooling Towers, and Chilled-Water Systems 12.3 Economizers, Demand-Controlled Ventilation, and VAV Air Distribution 12.4 Light-Commercial Start-Up, Commissioning, and Troubleshooting
13 Chapter 13: Light Commercial Refrigeration
13.1 Temperature Ranges, Box Loads, and Refrigeration System Types 13.2 Evaporators, Defrost Methods, and Defrost Controls 13.3 Condensing Units, Parallel Racks, Oil Management, and Capacity Control 13.4 Refrigeration Control Valves and Automatic Pump-Down 13.5 Commercial Refrigeration Diagnostics and Ice Machines
14 Chapter 14: Ductless, Mini-Split, and VRF Systems
14.1 Mini-Split Architecture and Inverter-Driven Compressors 14.2 Multi-Zone and VRF Operation, Electronic Expansion Valves, and Controls 14.3 Ductless Installation, Evacuation, Charging, and Diagnostics
15 Chapter 15: Building Automation and Digital Controls
15.1 DDC Fundamentals, Control Loops, and Sequences of Operation 15.2 BAS Networks, Protocols, and NEC-Compliant Cabling 15.3 Building Automation Controllers: Supervisory, Field, and Room Devices 15.4 Digital Logic, Numbering Systems, and Controller Programming 15.5 Sensor Selection, Installation, and Input Point Configuration 15.6 Actuators, Output Devices, and VFD Integration 15.7 Commercial Prints, Equipment Schedules, and BAS Documentation
13.1 Temperature Ranges, Box Loads, and Refrigeration System Types
Key Takeaways Explain This Topic AI
High-temperature refrigeration operates above about 32 degrees Fahrenheit evaporator, medium-temperature from roughly 32 down to 10 degrees, and low-temperature below about zero degrees Fahrenheit.
Coil temperature difference sets humidity: a 10 to 12 degree TD holds high humidity for produce and floral, while a 15 to 20 degree TD dehumidifies for packaged goods.
Box load is the sum of transmission, infiltration, product, and internal loads, and the equipment is sized on an 16 to 18 hour compressor run time per day.
Cryogenics deals with temperatures below about minus 150 degrees Fahrenheit and uses expendable refrigerants such as liquid nitrogen or carbon dioxide rather than a vapor-compression cycle.
A cascade system uses two separate refrigerant circuits joined by a cascade condenser-evaporator, allowing very low temperatures without an impractical single-stage compression ratio.
Last updated: August 2026
13.1 Temperature Ranges, Box Loads, and Refrigeration System Types
Light Commercial Refrigeration is one of the ten HVAC Excellence Professional Level written exams, and its competency sheet — 171 unique task lines — is the largest in the entire document. Its published description covers "equipment installation, service, system types, components, theory, applications, and troubleshooting."
Refrigeration differs from air conditioning in one fundamental way: air conditioning conditions people, refrigeration preserves product. A comfort system that runs 3°F warm produces a complaint. A refrigeration system that runs 3°F warm produces spoiled inventory and, in the food-safety world, a health department violation.
1. Temperature Classifications
The task list requires defining and stating the applications of high, medium, and low temperature refrigeration .
- Class Evaporator temperature Box temperature Typical application
- High temperature Above ≈ 32°F 45–60°F Florist coolers, wine storage, candy, air conditioning
- Medium temperature ≈ 32°F down to 10°F 32–45°F Walk-in coolers, dairy, produce, deli, reach-in refrigerators
- Low temperature ≈ 0°F down to −40°F 0°F to −10°F Walk-in freezers, ice cream, frozen food cases
- Ultra-low / cascade Below −40°F −40°F to −120°F Laboratory, blast freezing, pharmaceutical
- Cryogenics Below ≈ −150°F — Liquid nitrogen, liquid CO₂, medical and industrial gas
Cryogenics — a named task-list definition — is not a vapor-compression discipline. It uses expendable refrigerants : liquid nitrogen (−320°F) or liquid CO₂ is sprayed onto the product, absorbs heat, and is vented rather than recovered. An expendable refrigerant system has no compressor, condenser, or return loop; the refrigerant is consumed. Truck trailers, blast freezers, and emergency backup cooling use them.
2. Coil Temperature Difference and Box Humidity
The single most consequential design decision in commercial refrigeration is the coil TD — the difference between box air temperature and evaporator saturation temperature. TD = T box air − T evaporator saturation \text{TD} = T_{\text{box air}} - T_{\text{evaporator saturation}} TD = T box air − T evaporator saturation
- TD Resulting box RH Application
- 8–10°F 90–95% Produce, floral, unwrapped meat
- 10–12°F 85–90% General walk-in cooler, dairy
- 12–15°F 80–85% Packaged product, beverage
- 15–20°F 65–80% Dry-ish storage, some prep areas
Why TD controls humidity. A colder coil relative to the box air condenses more moisture out of the air passing over it. A small TD means a coil only slightly below box temperature, so it removes little moisture and the box stays humid. A large TD means a cold coil that wrings the air dry.
The consequences of getting it wrong are immediate and visible:
TD too large in a produce cooler → lettuce wilts, product loses saleable weight, and the coil frosts heavily.
TD too small in a packaged-goods box → condensation on packaging, soggy labels, and mold on gaskets and walls.
High-humidity evaporator coils — a named task-list item — achieve a small TD by using more surface area with wider fin spacing (typically 3–4 fins per inch instead of 6–8) and higher airflow, so the required capacity is delivered at a warmer coil temperature. Wide fin spacing also delays frost bridging in low-temperature applications.
3. Box Load Calculation
A refrigeration load has four components , and each is calculated over a 24-hour period.
Component What it is Notes
Transmission (wall) load Conduction through walls, ceiling, and floor U × A × Δ T U \times A \times \Delta T U × A × Δ T ; panels are typically R-25 to R-32 for coolers, R-32 to R-40 for freezers
Infiltration (air change) load Warm humid air entering when the door opens Both sensible and latent ; often the largest component in a busy box
Product load Cooling the product from entering to storage temperature, plus latent heat of freezing, plus respiration for produce Governed by the product's specific heat above and below freezing and its latent heat of fusion
Internal load Evaporator fan motors, lights, defrost heaters, forklifts, people Fan motors run nearly continuously and are a surprisingly large freezer load
Product load arithmetic uses three terms: Q = ( m × c above × Δ T 1 ) + ( m × h i f ) + ( m × c below × Δ T 2 ) Q = (m \times c_{\text{above}} \times \Delta T_1) + (m \times h_{if}) + (m \times c_{\text{below}} \times \Delta T_2) Q = ( m × c above × Δ T 1 ) + ( m × h i f ) + ( m × c below × Δ T 2 )
where c above c_{\text{above}} c above is the specific heat above freezing, h i f h_{if} h i f is the latent heat of fusion, and c below c_{\text{below}} c below is the specific heat below freezing. For most foods, c above ≈ 0.7 c_{\text{above}} \approx 0.7 c above ≈ 0.7 –0.9, c below ≈ 0.4 c_{\text{below}} \approx 0.4 c below ≈ 0.4 –0.5, and h i f ≈ 100 h_{if} \approx 100 h i f ≈ 100 –130 BTU/lb, all dominated by the food's water content.
Sizing on run time. The daily total load is divided by the intended compressor run hours per day to get required capacity: Required capacity (BTU/hr) = Total 24-hour load (BTU) Run hours \text{Required capacity (BTU/hr)} = \frac{\text{Total 24-hour load (BTU)}}{\text{Run hours}} Required capacity (BTU/hr) = Run hours Total 24-hour load (BTU)
Standard practice is 16 hours for low-temperature systems (leaving 8 hours for defrost and off cycles) and 16–18 hours for medium temperature. Sizing on 24 hours leaves no reserve for pull-down or door abuse; sizing on 10 hours produces a badly oversized system that short-cycles and never dehumidifies.
4. Equipment Families
- Type Description
- Self-contained (integral) reach-in Complete system in the cabinet; plug-in
Remote condensing unit + evaporator The standard walk-in arrangement: an outdoor or machine-room condensing unit, a field-run line set, and a unit cooler in the box
Multiplexed / parallel rack Several compressors manifolded to a common suction and discharge header, serving many cases at one temperature level
Distributed / secondary loop A chiller cools a secondary fluid (glycol, CO₂) circulated to the cases, dramatically reducing refrigerant charge
Transcritical CO₂ (R-744) Increasingly common in supermarkets; operates above the critical point on hot days with a gas cooler instead of a condenser
- Cascade Two independent circuits joined by one heat exchanger
- Cascade systems
A cascade system — a named task-list competency — uses two separate refrigerant circuits that never mix, joined by a cascade condenser-evaporator : the low-stage circuit's condenser is the high-stage circuit's evaporator.
Why: achieving −60°F in a single stage would require a compression ratio well above 15:1 (Section 4.4), with collapsed volumetric efficiency and destructive discharge temperatures.
How: the low stage uses a low-boiling-point refrigerant (historically R-503 or R-23; now R-508B, R-170, or CO₂) that would be at absurd pressure if condensed at ambient. The high stage uses a conventional refrigerant and rejects to ambient. Each stage runs a sane compression ratio.
Fade-out (expansion) tank: the low-stage circuit is charged with a refrigerant whose pressure at room temperature would be dangerously high, so a fade-out tank absorbs the charge when the system is off and warm.
Start-up order: the high stage must run first to pull the cascade heat exchanger down before the low stage can condense.
Two-stage (compound) systems
An alternative for low-temperature work: one refrigerant, two compression stages in series, with an intercooler or desuperheater between them to cool the interstage gas. Simpler than cascade but limited by the refrigerant's own properties at the lowest temperature.
5. What the Refrigerant Sees Differently
Everything in Chapter 4 applies, with three practical differences at refrigeration temperatures:
Compression ratios are high (Section 4.4). Volumetric efficiency, discharge temperature, and oil condition all matter far more than in air conditioning.
Oil return is harder. Low-temperature suction gas is at low density, so velocity requirements (Section 6.5) are more demanding, and oil viscosity rises as it gets colder. This is why oil separators, properly trapped risers, and correct line sizing are standard practice on refrigeration and optional on comfort cooling.
Defrost is mandatory below about 34°F evaporator temperature (Section 13.2). An air conditioning coil never frosts in normal operation; a freezer coil frosts continuously and would block completely within hours without a defrost strategy.