Study guide

11.3 Mixed Air, Ventilation, and Infiltration Calculations

HVAC Excellence Certification Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction, Safety, Tools, and Diagnostic Method

1.1 HVAC Excellence Certification, Industry Codes, and Standards 1.2 Electrical Safety, PPE, Lockout/Tagout, and Hazard Communication 1.3 Multimeters, Manifold Gauges, Micron Gauges, and Diagnostic Instruments 1.4 HVACR Mathematics, Unit Conversions, and Efficiency Ratings 1.5 OSHA Standards, Fall Protection, Rigging, and Confined Spaces 1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs 1.7 Systematic Troubleshooting: Data Plates, Manufacturer Literature, and Diagnostic Method

2 Chapter 2: Electrical Fundamentals and Circuit Theory

2.1 Voltage, Current, Resistance, and Ohm's Law Calculations 2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations 2.3 AC Fundamentals, Single-Phase vs Three-Phase Power, and Control Transformers 2.4 Conductors, Insulators, Wire Sizing, Voltage Drop, and NEC Ampacity

3 Chapter 3: Electrical Components, Motors, and Schematics

3.1 Contactors, Relays, Switches, Overload Protection, and Thermostats 3.2 HVAC Motors (PSC, CSIR, CSCR, ECM, 3-Phase) and Run/Start Capacitors 3.3 Interpreting Ladder Diagrams, Schematics, and Point-to-Point Wiring 3.4 Motor Testing, Insulation Resistance, Bearings, and Belt Drives

4 Chapter 4: Thermodynamics and the Refrigeration Cycle

4.1 Heat Transfer, Temperature Scales, BTUs, Sensible vs Latent Heat, and Enthalpy 4.2 The Four Vapor-Compression Cycle Stages (Compression, Condensation, Expansion, Evaporation) 4.3 P-T Charts, Saturated Conditions, Target Superheat, and Subcooling Calculations 4.4 Pressure–Enthalpy Diagrams, Compression Ratio, and Cycle Analysis

5 Chapter 5: Refrigerants, Environmental Regulations, and Recovery

5.1 Refrigerant Types (CFC, HCFC, HFC, HFO, HC) and ASHRAE Safety Groups (A1, A2L, A3) 5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards 5.3 Recovery/Recycling/Reclaiming Equipment, Procedures, and Leak Detection 5.4 Refrigerant Retrofits, Cylinder Handling, and Refrigerant Purity 5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice

6 Chapter 6: Refrigeration System Components and Accessories

6.1 Compressor Mechanics (Reciprocating, Scroll, Rotary, Screw) and Failures 6.2 Expansion Devices (TXV/TEV, Fixed Orifice, EEV) and Superheat Control 6.3 Condensers, Evaporators, Filter-Driers, Accumulators, Receivers, and Solenoids 6.4 Pressure Controls, Capacity Controls, and System Protection 6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice

7 Chapter 7: Gas Heating, Combustion Analysis, and Fuel Piping

7.1 Combustion Theory, Fuel Gases (Natural Gas vs LP), and Gas Burners 7.2 Gas Valves, Ignition Systems (Standing Pilot, Spark, HSI), and Safety Limit Controls 7.3 Flue Venting, Draft Principles, Combustion Analysis, and CO Safety 7.4 Fuel-Gas and Oil Piping, Vent System Selection and Sizing, and Installation Practice

8 Chapter 8: Electric Heating, Oil Heat, and Hydronics

8.1 Electric Heating Elements, Sequencers, Limit Switches, and kW Calculations 8.2 Oil Burners, Fuel Pumps, Nozzles, Ignition Electrodes, and Primary Controls 8.3 Hydronic Boilers, Circulator Pumps, Expansion Tanks, and Zone Controls 8.4 Combustion Air, Water Heaters, and Combustion Appliance Zone Testing

9 Chapter 9: Heat Pumps and Dual-Fuel Systems

9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation 9.2 Defrost Controls (Time-Temperature, Demand Defrost), Sensors, and Sequences 9.3 Balance Points, Auxiliary/Emergency Heat, and Dual-Fuel (Hybrid) Systems 9.4 Heat Pump Diagnostics, Refrigerant Flow, and Troubleshooting Procedures 9.5 Heat Pump Types, Cold-Climate Performance, and Sizing Approaches

10 Chapter 10: Air Distribution, IAQ, and System Commissioning

10.1 Airflow Fundamentals, CFM Measurement, External Static Pressure, and Fan Laws 10.2 Duct Sizing Principles, Supply/Return Distribution, Dampers, and Air Balancing 10.3 Indoor Air Quality, MERV Ratings, Electronic Cleaners, Humidification, and Dehumidification 10.4 Deep Vacuum Evacuation (Micron Gauge), Subcooling/Superheat Charging, and System Commissioning 10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance

11 Chapter 11: Psychrometrics, Airside Calculations, and Load Estimation

11.1 Reading the Psychrometric Chart: Properties and Plotting 11.2 The Eight Air-Conditioning Processes and the Process Triangle 11.3 Mixed Air, Ventilation, and Infiltration Calculations 11.4 Residential Heat Loss, Heat Gain, and Equipment Sizing

12 Chapter 12: Light Commercial Air Conditioning

12.1 Packaged Rooftop and Split Light-Commercial Systems 12.2 Water-Cooled Condensers, Cooling Towers, and Chilled-Water Systems 12.3 Economizers, Demand-Controlled Ventilation, and VAV Air Distribution 12.4 Light-Commercial Start-Up, Commissioning, and Troubleshooting

13 Chapter 13: Light Commercial Refrigeration

13.1 Temperature Ranges, Box Loads, and Refrigeration System Types 13.2 Evaporators, Defrost Methods, and Defrost Controls 13.3 Condensing Units, Parallel Racks, Oil Management, and Capacity Control 13.4 Refrigeration Control Valves and Automatic Pump-Down 13.5 Commercial Refrigeration Diagnostics and Ice Machines

14 Chapter 14: Ductless, Mini-Split, and VRF Systems

14.1 Mini-Split Architecture and Inverter-Driven Compressors 14.2 Multi-Zone and VRF Operation, Electronic Expansion Valves, and Controls 14.3 Ductless Installation, Evacuation, Charging, and Diagnostics

15 Chapter 15: Building Automation and Digital Controls

15.1 DDC Fundamentals, Control Loops, and Sequences of Operation 15.2 BAS Networks, Protocols, and NEC-Compliant Cabling 15.3 Building Automation Controllers: Supervisory, Field, and Room Devices 15.4 Digital Logic, Numbering Systems, and Controller Programming 15.5 Sensor Selection, Installation, and Input Point Configuration 15.6 Actuators, Output Devices, and VFD Integration 15.7 Commercial Prints, Equipment Schedules, and BAS Documentation

11.3 Mixed Air, Ventilation, and Infiltration Calculations

Key Takeaways Explain This Topic AI

Mixed air temperature is the outdoor-air fraction times outdoor temperature plus the return-air fraction times return temperature.

The mixed-air state point falls on the straight line between the outdoor and return points, positioned by the outdoor-air percentage.

Ventilation load is calculated on outdoor conditions with the same 1.08, 0.68 and 4.5 constants, and in humid climates the latent portion often exceeds the sensible portion.

Infiltration in CFM equals conditioned volume times natural air changes per hour divided by 60, and natural ACH is roughly ACH50 divided by an LBL climate factor of about 15 to 20.

Energy recovery ventilators transfer both sensible heat and moisture between exhaust and intake air, while heat recovery ventilators transfer sensible heat only.

Last updated: August 2026

11.3 Mixed Air, Ventilation, and Infiltration Calculations

"Calculating mixed air problems for infiltration and ventilation" appears on both the General Studies and System Performance sheets. It is the calculation that connects the psychrometric chart (Sections 11.1 and 11.2) to real equipment selection, because almost no air handler recirculates 100% of its return air, and no building is airtight.

1. The Mixing Equation

When two airstreams combine, the result is a weighted average by mass . Since specific volume varies only slightly across normal conditions, weighting by volume (CFM) is accurate enough for field work. T mixed = ( CFM OA CFM total × T OA ) + ( CFM RA CFM total × T RA ) T_{\text{mixed}} = \left(\frac{\text{CFM}_{\text{OA}}}{\text{CFM}_{\text{total}}} \times T_{\text{OA}}\right) + \left(\frac{\text{CFM}_{\text{RA}}}{\text{CFM}_{\text{total}}} \times T_{\text{RA}}\right) T mixed ​ = ( CFM total ​ CFM OA ​ ​ × T OA ​ ) + ( CFM total ​ CFM RA ​ ​ × T RA ​ )

The same weighting applies to humidity ratio (grains) and enthalpy . It does not apply to relative humidity, which is a ratio rather than a quantity — averaging two RH values is a common and wrong shortcut.

Worked example — commercial rooftop, summer. A unit moves 8,000 CFM total with 2,000 CFM of outdoor air (25% OA). Outdoor air is 95°F DB / 78°F WB (about 120 grains/lb, 41.5 BTU/lb); return air is 75°F DB / 63°F WB (65 grains/lb, 28.6 BTU/lb). T mixed = ( 0.25 × 95 ) + ( 0.75 × 75 ) = 23.75 + 56.25 = 80.0 ∘ F DB T_{\text{mixed}} = (0.25 \times 95) + (0.75 \times 75) = 23.75 + 56.25 = 80.0^\circ\text{F DB} T mixed ​ = ( 0.25 × 95 ) + ( 0.75 × 75 ) = 23.75 + 56.25 = 80. 0 ∘ F DB W mixed = ( 0.25 × 120 ) + ( 0.75 × 65 ) = 30 + 48.75 = 78.75 grains/lb W_{\text{mixed}} = (0.25 \times 120) + (0.75 \times 65) = 30 + 48.75 = 78.75\text{ grains/lb} W mixed ​ = ( 0.25 × 120 ) + ( 0.75 × 65 ) = 30 + 48.75 = 78.75 grains/lb h mixed = ( 0.25 × 41.5 ) + ( 0.75 × 28.6 ) = 10.4 + 21.5 = 31.9 BTU/lb h_{\text{mixed}} = (0.25 \times 41.5) + (0.75 \times 28.6) = 10.4 + 21.5 = 31.9\text{ BTU/lb} h mixed ​ = ( 0.25 × 41.5 ) + ( 0.75 × 28.6 ) = 10.4 + 21.5 = 31.9 BTU/lb

Plot 80°F DB and 78.75 grains: the mixed-air wet bulb reads about 67°F . That 80°F/67°F condition — not the 75°F/63°F return air — is what actually enters the cooling coil, and it is what the coil must be selected for.

The graphical solution

On the chart, the mixed-air point always lies on the straight line connecting the outdoor and return points , and its position along that line is set by the outdoor-air fraction — measured from the return point toward the outdoor point. At 25% OA the mixed point sits one-quarter of the way from return toward outdoor. Sketching this is faster than the arithmetic and is exactly the "plot any two points and evaluate the data" skill the task list requires.

Winter mixed air and the freeze-stat

The same math in January exposes a real hazard. With 10°F outdoor air, 72°F return, and 25% OA: T mixed = ( 0.25 × 10 ) + ( 0.75 × 72 ) = 2.5 + 54 = 56.5 ∘ F T_{\text{mixed}} = (0.25 \times 10) + (0.75 \times 72) = 2.5 + 54 = 56.5^\circ\text{F} T mixed ​ = ( 0.25 × 10 ) + ( 0.75 × 72 ) = 2.5 + 54 = 56. 5 ∘ F

Comfortable. But if the outdoor-air damper sticks open at 50%: T mixed = ( 0.50 × 10 ) + ( 0.50 × 72 ) = 41 ∘ F T_{\text{mixed}} = (0.50 \times 10) + (0.50 \times 72) = 41^\circ\text{F} T mixed ​ = ( 0.50 × 10 ) + ( 0.50 × 72 ) = 4 1 ∘ F

That air is approaching the point where a hydronic preheat or chilled-water coil will freeze and split. This is why every commercial mixed-air system carries a low-limit (freeze-stat) — typically a capillary sensing element serpentined across the coil face, tripping near 35–38°F , responding to the coldest one-foot segment of its capillary rather than an average.

2. Ventilation Load

Outdoor air brought in deliberately must be conditioned, and its load is calculated on outdoor conditions, not mixed conditions. Q s , vent = 1.08 × CFM OA × ( T OA − T room ) Q_{s,\text{vent}} = 1.08 \times \text{CFM}_{\text{OA}} \times (T_{\text{OA}} - T_{\text{room}}) Q s , vent ​ = 1.08 × CFM OA ​ × ( T OA ​ − T room ​ ) Q l , vent = 0.68 × CFM OA × ( W OA − W room ) Q_{l,\text{vent}} = 0.68 \times \text{CFM}_{\text{OA}} \times (W_{\text{OA}} - W_{\text{room}}) Q l , vent ​ = 0.68 × CFM OA ​ × ( W OA ​ − W room ​ )

Worked example. 2,000 CFM of 95°F/120-grain outdoor air conditioned to a 75°F/65-grain room: Q s = 1.08 × 2,000 × 20 = 43,200 BTU/hr Q_s = 1.08 \times 2{,}000 \times 20 = 43{,}200\text{ BTU/hr} Q s ​ = 1.08 × 2 , 000 × 20 = 43 , 200 BTU/hr Q l = 0.68 × 2,000 × 55 = 74,800 BTU/hr Q_l = 0.68 \times 2{,}000 \times 55 = 74{,}800\text{ BTU/hr} Q l ​ = 0.68 × 2 , 000 × 55 = 74 , 800 BTU/hr

Total ventilation load: 118,000 BTU/hr — nearly 10 tons , of which 63% is latent . In humid climates the moisture in outdoor air is usually a larger burden than its temperature, which is the entire argument for dedicated outdoor air systems and energy recovery.

How much outdoor air? ASHRAE 62.1's Ventilation Rate Procedure sets commercial rates as people-based plus area-based: V b z = ( R p × P z ) + ( R a × A z ) V_{bz} = (R_p \times P_z) + (R_a \times A_z) V b z ​ = ( R p ​ × P z ​ ) + ( R a ​ × A z ​ )

An office at R p = 5 R_p = 5 R p ​ = 5 CFM/person and R a = 0.06 R_a = 0.06 R a ​ = 0.06 CFM/ft², with 40 people in 4,000 ft²: ( 5 × 40 ) + ( 0.06 × 4,000 ) = 200 + 240 = 440 CFM (5 \times 40) + (0.06 \times 4{,}000) = 200 + 240 = 440\text{ CFM} ( 5 × 40 ) + ( 0.06 × 4 , 000 ) = 200 + 240 = 440 CFM to the breathing zone. Residential whole-building ventilation uses the ASHRAE 62.2 formula in Section 1.1.

3. Infiltration

Infiltration is uncontrolled air leakage driven by stack effect, wind, and mechanical imbalance (Section 10.5). CFM infiltration = Conditioned volume (ft 3 ) × ACH natural 60 \text{CFM}_{\text{infiltration}} = \frac{\text{Conditioned volume (ft}^3) \times \text{ACH}_{\text{natural}}}{60} CFM infiltration ​ = 60 Conditioned volume (ft 3 ) × ACH natural ​ ​

Converting a blower door result to a design rate. ACH50 is a test result at 50 Pa; natural infiltration happens at roughly 1–4 Pa. The LBL (Lawrence Berkeley Laboratory) division method converts between them: ACH natural ≈ ACH50 N \text{ACH}_{\text{natural}} \approx \frac{\text{ACH50}}{N} ACH natural ​ ≈ N ACH50 ​

where N is a climate, height, and shielding factor , typically 15 to 20 for a one- or two-story house — around 20 in mild, sheltered locations and nearer 15 in cold, windy, exposed ones.

Worked example. A 22,300 ft³ house tests at 5.65 ACH50 in a moderate climate ( N = 18 N = 18 N = 18 ): ACH natural = 5.65 ÷ 18 = 0.314 \text{ACH}_{\text{natural}} = 5.65 \div 18 = 0.314 ACH natural ​ = 5.65 ÷ 18 = 0.314 CFM infiltration = 22,300 × 0.314 60 = 7,002 60 = 117 CFM \text{CFM}_{\text{infiltration}} = \frac{22{,}300 \times 0.314}{60} = \frac{7{,}002}{60} = 117\text{ CFM} CFM infiltration ​ = 60 22 , 300 × 0.314 ​ = 60 7 , 002 ​ = 117 CFM

At winter design conditions of 15°F outdoors and 70°F indoors: Q s = 1.08 × 117 × 55 = 6,950 BTU/hr Q_s = 1.08 \times 117 \times 55 = 6{,}950\text{ BTU/hr} Q s ​ = 1.08 × 117 × 55 = 6 , 950 BTU/hr

That single number is often 15–25% of a house's entire design heating load, and it is why air sealing appears in a heat load calculation as directly as insulation does.

The 0.35 ACH rule of thumb — the old assumption that a house "naturally" changes its air about a third of a time per hour — is a historical average, not a measurement. Modern practice measures with a blower door and calculates, because real houses range from 0.05 to over 1.0 ACH natural.

4. Energy and Heat Recovery Ventilation

The ventilation-load arithmetic above is the case for recovering energy from the air being exhausted.

  • HRV (Heat Recovery Ventilator) ERV (Energy Recovery Ventilator)
  • Transfers Sensible heat only Sensible heat and moisture
  • Core Plate or fixed-plate heat exchanger Enthalpy wheel or membrane core

Best climate Cold, heating-dominated; also where indoor humidity is already too high Hot-humid, and cold-dry where retaining indoor moisture in winter is desirable

Typical effectiveness 55–85% sensible 50–80% sensible, 40–70% latent

An ERV in the 2,000 CFM example above, at 70% sensible and 60% latent effectiveness, would cut the ventilation load from 118,000 BTU/hr to roughly 43,200 × 0.30 + 74,800 × 0.40 = 12,960 + 29,920 = 42,880 43{,}200 \times 0.30 + 74{,}800 \times 0.40 = 12{,}960 + 29{,}920 = 42{,}880 43 , 200 × 0.30 + 74 , 800 × 0.40 = 12 , 960 + 29 , 920 = 42 , 880 BTU/hr — a saving of about 6 tons of coil capacity .

Balanced airflow is the requirement. An HRV or ERV must move approximately equal supply and exhaust volumes; an imbalance pressurizes or depressurizes the building and reintroduces exactly the uncontrolled infiltration the system exists to replace. Commissioning includes measuring both airstreams and adjusting to within roughly 10% of each other.

Demand-controlled ventilation (Section 12.3) reduces the load a different way: a CO₂ sensor in the space modulates the outdoor-air damper to actual occupancy rather than design occupancy, which in intermittently occupied spaces such as conference rooms, gyms, and auditoriums is the largest single ventilation saving available.