Study guide
5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice
HVAC Excellence Certification Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction, Safety, Tools, and Diagnostic Method
1.1 HVAC Excellence Certification, Industry Codes, and Standards 1.2 Electrical Safety, PPE, Lockout/Tagout, and Hazard Communication 1.3 Multimeters, Manifold Gauges, Micron Gauges, and Diagnostic Instruments 1.4 HVACR Mathematics, Unit Conversions, and Efficiency Ratings 1.5 OSHA Standards, Fall Protection, Rigging, and Confined Spaces 1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs 1.7 Systematic Troubleshooting: Data Plates, Manufacturer Literature, and Diagnostic Method
2 Chapter 2: Electrical Fundamentals and Circuit Theory
2.1 Voltage, Current, Resistance, and Ohm's Law Calculations 2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations 2.3 AC Fundamentals, Single-Phase vs Three-Phase Power, and Control Transformers 2.4 Conductors, Insulators, Wire Sizing, Voltage Drop, and NEC Ampacity
3 Chapter 3: Electrical Components, Motors, and Schematics
3.1 Contactors, Relays, Switches, Overload Protection, and Thermostats 3.2 HVAC Motors (PSC, CSIR, CSCR, ECM, 3-Phase) and Run/Start Capacitors 3.3 Interpreting Ladder Diagrams, Schematics, and Point-to-Point Wiring 3.4 Motor Testing, Insulation Resistance, Bearings, and Belt Drives
4 Chapter 4: Thermodynamics and the Refrigeration Cycle
4.1 Heat Transfer, Temperature Scales, BTUs, Sensible vs Latent Heat, and Enthalpy 4.2 The Four Vapor-Compression Cycle Stages (Compression, Condensation, Expansion, Evaporation) 4.3 P-T Charts, Saturated Conditions, Target Superheat, and Subcooling Calculations 4.4 Pressure–Enthalpy Diagrams, Compression Ratio, and Cycle Analysis
5 Chapter 5: Refrigerants, Environmental Regulations, and Recovery
5.1 Refrigerant Types (CFC, HCFC, HFC, HFO, HC) and ASHRAE Safety Groups (A1, A2L, A3) 5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards 5.3 Recovery/Recycling/Reclaiming Equipment, Procedures, and Leak Detection 5.4 Refrigerant Retrofits, Cylinder Handling, and Refrigerant Purity 5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice
6 Chapter 6: Refrigeration System Components and Accessories
6.1 Compressor Mechanics (Reciprocating, Scroll, Rotary, Screw) and Failures 6.2 Expansion Devices (TXV/TEV, Fixed Orifice, EEV) and Superheat Control 6.3 Condensers, Evaporators, Filter-Driers, Accumulators, Receivers, and Solenoids 6.4 Pressure Controls, Capacity Controls, and System Protection 6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice
7 Chapter 7: Gas Heating, Combustion Analysis, and Fuel Piping
7.1 Combustion Theory, Fuel Gases (Natural Gas vs LP), and Gas Burners 7.2 Gas Valves, Ignition Systems (Standing Pilot, Spark, HSI), and Safety Limit Controls 7.3 Flue Venting, Draft Principles, Combustion Analysis, and CO Safety 7.4 Fuel-Gas and Oil Piping, Vent System Selection and Sizing, and Installation Practice
8 Chapter 8: Electric Heating, Oil Heat, and Hydronics
8.1 Electric Heating Elements, Sequencers, Limit Switches, and kW Calculations 8.2 Oil Burners, Fuel Pumps, Nozzles, Ignition Electrodes, and Primary Controls 8.3 Hydronic Boilers, Circulator Pumps, Expansion Tanks, and Zone Controls 8.4 Combustion Air, Water Heaters, and Combustion Appliance Zone Testing
9 Chapter 9: Heat Pumps and Dual-Fuel Systems
9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation 9.2 Defrost Controls (Time-Temperature, Demand Defrost), Sensors, and Sequences 9.3 Balance Points, Auxiliary/Emergency Heat, and Dual-Fuel (Hybrid) Systems 9.4 Heat Pump Diagnostics, Refrigerant Flow, and Troubleshooting Procedures 9.5 Heat Pump Types, Cold-Climate Performance, and Sizing Approaches
10 Chapter 10: Air Distribution, IAQ, and System Commissioning
10.1 Airflow Fundamentals, CFM Measurement, External Static Pressure, and Fan Laws 10.2 Duct Sizing Principles, Supply/Return Distribution, Dampers, and Air Balancing 10.3 Indoor Air Quality, MERV Ratings, Electronic Cleaners, Humidification, and Dehumidification 10.4 Deep Vacuum Evacuation (Micron Gauge), Subcooling/Superheat Charging, and System Commissioning 10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance
11 Chapter 11: Psychrometrics, Airside Calculations, and Load Estimation
11.1 Reading the Psychrometric Chart: Properties and Plotting 11.2 The Eight Air-Conditioning Processes and the Process Triangle 11.3 Mixed Air, Ventilation, and Infiltration Calculations 11.4 Residential Heat Loss, Heat Gain, and Equipment Sizing
12 Chapter 12: Light Commercial Air Conditioning
12.1 Packaged Rooftop and Split Light-Commercial Systems 12.2 Water-Cooled Condensers, Cooling Towers, and Chilled-Water Systems 12.3 Economizers, Demand-Controlled Ventilation, and VAV Air Distribution 12.4 Light-Commercial Start-Up, Commissioning, and Troubleshooting
13 Chapter 13: Light Commercial Refrigeration
13.1 Temperature Ranges, Box Loads, and Refrigeration System Types 13.2 Evaporators, Defrost Methods, and Defrost Controls 13.3 Condensing Units, Parallel Racks, Oil Management, and Capacity Control 13.4 Refrigeration Control Valves and Automatic Pump-Down 13.5 Commercial Refrigeration Diagnostics and Ice Machines
14 Chapter 14: Ductless, Mini-Split, and VRF Systems
14.1 Mini-Split Architecture and Inverter-Driven Compressors 14.2 Multi-Zone and VRF Operation, Electronic Expansion Valves, and Controls 14.3 Ductless Installation, Evacuation, Charging, and Diagnostics
15 Chapter 15: Building Automation and Digital Controls
15.1 DDC Fundamentals, Control Loops, and Sequences of Operation 15.2 BAS Networks, Protocols, and NEC-Compliant Cabling 15.3 Building Automation Controllers: Supervisory, Field, and Room Devices 15.4 Digital Logic, Numbering Systems, and Controller Programming 15.5 Sensor Selection, Installation, and Input Point Configuration 15.6 Actuators, Output Devices, and VFD Integration 15.7 Commercial Prints, Equipment Schedules, and BAS Documentation
5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice
Key Takeaways Explain This Topic AI
The AIM Act requires an 85% phasedown of HFC production and consumption by 2036 against a 2011-2013 baseline, driving the move to A2L refrigerants.
A2L means lower toxicity with a maximum burning velocity of 10 cm/s or less, which is roughly one-tenth the burning velocity of propane.
UL 60335-2-40 requires A2L mitigation to keep refrigerant concentration below 25% of the lower flammability limit, typically by running the indoor blower on leak detection.
A2L service requires a leak detector rated for the specific refrigerant, non-sparking tools where mandated, and recovery equipment listed for flammable refrigerants.
A2L refrigerant cylinders are shipped as DOT Division 2.1 flammable gas with a red band and left-hand-thread valve connections, unlike A1 cylinders.
Last updated: August 2026
5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice
The Low GWP Refrigerants sheet is one of the fifteen competency areas on the HVAC Excellence task list, and it backs a dedicated Specialty Certification. Its closing block is explicit: candidates must "have a general understanding of the industry codes and standards that affect the safe use and handling of A2L refrigerants, including ASHRAE Standards 15 and 15.2, UL 60335-2-40 and UL 60335-2-89, EPA SNAP rulings, and the American Innovation and Manufacturing (AIM) Act ." This is the newest material on the exam and the most likely to be updated.
1. The Regulatory Driver: the AIM Act
The American Innovation and Manufacturing Act of 2020 gave EPA three distinct authorities:
Subsection Authority What it produced
(a) Phase down HFC production and consumption An 85% reduction by 2036 measured against a 2011–2013 baseline, implemented through an allowance allocation system
(i) Restrict HFCs by sector The Technology Transitions rule — GWP limits by end use, which is why new residential and light commercial AC and heat pump equipment moved to A2L refrigerants
(h) Maximize reclaim, minimize release The Emissions Reduction and Reclamation rule — leak repair at 15 lb, automatic leak detection at 1,500 lb, effective January 1, 2026 (see Section 5.2)
Under the Technology Transitions rule, new residential and light commercial air conditioners and heat pumps manufactured from January 1, 2025 must use a refrigerant with a GWP at or below the applicable sector limit. The market answer was R-454B (GWP ≈ 466) and R-32 (GWP ≈ 675), both A2L , replacing R-410A (GWP ≈ 2,088). Existing R-410A equipment remains legal to service indefinitely.
2. What A2L Actually Means
ASHRAE Standard 34 assigns two characters: toxicity (A = lower, OEL ≥ 400 ppm) and flammability. The 2L subclass was created specifically to separate mildly flammable refrigerants from genuinely flammable ones.
A refrigerant is Class 2L when it exhibits flame propagation, has a heat of combustion below 19,000 kJ/kg , and has a maximum burning velocity of 10 cm/s or less at 60°C and 101.3 kPa.
- Property R-410A (A1) R-454B (A2L) R-290 propane (A3)
- Burning velocity none ≤ 10 cm/s (about 6 cm/s) ≈ 46 cm/s
- Ignition energy n/a Very high — a spark rarely ignites it Low
- GWP ≈ 2,088 ≈ 466 3
The practical meaning: an A2L will burn, but only within a narrow concentration band, only with a sustained high-energy ignition source, and with a flame front that travels slowly enough that a running blower disperses the vapor faster than it can accumulate. It is not equivalent to a propane leak. It is also not inert, and the old habit of ignoring a small leak is no longer acceptable.
Also note R-454B and R-32 are mildly flammable but still HFC-based ; they are not "natural" refrigerants, and their glide differs: R-32 is a single component with essentially no glide, while R-454B is a zeotropic blend with a small glide (about 1.5°F) that still requires liquid charging.
3. The Codes and Standards
ANSI/ASHRAE Standard 15 — the safety standard for refrigeration systems: machinery rooms, refrigerant concentration limits, relief device sizing and discharge. Standard 15.2 was created specifically for residential and light commercial systems and carries the A2L installation requirements for that equipment class.
ANSI/ASHRAE Standard 34 — assigns the safety group and the Refrigerant Concentration Limit (RCL) , the maximum concentration allowed in an occupied space.
UL/CSA 60335-2-40 — the product safety standard for heat pumps, air conditioners, and dehumidifiers . It replaced UL 1995 and contains the A2L mitigation requirements.
UL/CSA 60335-2-89 — the parallel standard for commercial refrigerating appliances , which raised the allowable A3 (hydrocarbon) charge from 150 g to as much as 500 g in self-contained equipment.
EPA SNAP (Significant New Alternatives Policy) — lists substitutes as acceptable, acceptable with use conditions, or unacceptable, by end use. A2Ls are listed acceptable subject to use conditions , which include the UL listings and specific installation requirements.
Model codes — the IMC, IFGC, IRC, and UMC have been amended to adopt A2L provisions. Local adoption lags, so the authority having jurisdiction determines what applies on any given job.
4. Charge Limits and Mitigation
The controlling idea in UL 60335-2-40 is simple: keep the concentration in the occupied space below 25% of the lower flammability limit (LFL) under any credible leak scenario.
Maximum charge for a given room is a function of the refrigerant's LFL, the conditioned floor area , the installation height of the indoor unit, and whether mitigation is present. Larger rooms and mitigation permit larger charges. Manufacturers publish minimum-room-area tables; use them rather than a rule of thumb.
Mitigation on ducted equipment normally means:
A factory-installed refrigerant detection sensor (RDS) in the indoor unit or supply plenum.
On detection, the control shuts off the compressor , opens dampers if fitted , and energizes the indoor blower to a specified minimum airflow, diluting the leak below 25% LFL.
A fault/lockout condition that requires service attention rather than an automatic reset.
The RDS is a service item. Sensors have a stated life (commonly 10–15 years) and must be replaced, not defeated. Jumpering out a refrigerant sensor to "get the customer running" defeats the entire listed safety system and voids the listing.
No open ignition sources may be located in the airstream where A2L could accumulate. This is why an A2L air handler cannot share a cabinet with an open-flame appliance.
5. Service Practice: What Changes
Most A2L service is identical to A1 service. The differences are specific and testable.
Task A2L requirement
Leak detection Use a detector rated for the specific A2L refrigerant . A halogen-sensitive detector calibrated for R-410A may respond poorly to R-32-based blends. Never use a halide torch.
Recovery Recovery machine, hoses, and cylinder must be listed for flammable refrigerants . A2L recovery machines have spark-free motors and internal pressure protection.
Cylinders A2L cylinders ship as DOT Division 2.1 flammable gas , marked with a red band , and use left-hand-thread valve connections so they cannot be cross-connected to A1 equipment. Transport rules, quantity limits, and placarding differ from A1.
Ventilation Ventilate the work area. In a basement, crawlspace, or closet, force air movement before and during any procedure that could release refrigerant.
Ignition sources No smoking, no open flame, no non-rated electrical devices in the immediate work zone. Brazing is performed only after full recovery and a nitrogen purge.
Nitrogen pressure testing Standard practice, and even more important — a proven-tight system is the primary A2L safeguard.
Charging R-454B is zeotropic: charge liquid , use bubble point for subcooling and dew point for superheat. R-32 is a single component with no glide.
Do not mix Never add A2L to an R-410A system or vice versa. Pressures are close enough that the mistake is easy and the result is an unlisted, off-composition, mildly flammable charge.
Storage Store A2L cylinders in a ventilated area away from ignition sources, upright and secured, and separated from oxidizers.
Practical field notes
R-454B and R-410A pressures are similar but not identical, and their P-T behavior diverges at the extremes. Always use the correct chart.
A2L systems often use POE oil , so the hygroscopic handling rules from Section 5.4 apply — keep containers sealed, evacuate deeply, replace the drier.
Equipment labeling identifies the refrigerant, its safety group, and the required mitigation. Read it before touching anything; retrofitted or mislabeled equipment is a real hazard.
Technician certification: EPA Section 608 certification remains the legal requirement for handling regulated refrigerants and their substitutes, including A2Ls. The HVAC Excellence Low GWP Refrigerant Safety Specialty Certification is a separate 50-question credential that documents A2L-specific competence.