Study guide

5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards

HVAC Excellence Certification Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction, Safety, Tools, and Diagnostic Method

1.1 HVAC Excellence Certification, Industry Codes, and Standards 1.2 Electrical Safety, PPE, Lockout/Tagout, and Hazard Communication 1.3 Multimeters, Manifold Gauges, Micron Gauges, and Diagnostic Instruments 1.4 HVACR Mathematics, Unit Conversions, and Efficiency Ratings 1.5 OSHA Standards, Fall Protection, Rigging, and Confined Spaces 1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs 1.7 Systematic Troubleshooting: Data Plates, Manufacturer Literature, and Diagnostic Method

2 Chapter 2: Electrical Fundamentals and Circuit Theory

2.1 Voltage, Current, Resistance, and Ohm's Law Calculations 2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations 2.3 AC Fundamentals, Single-Phase vs Three-Phase Power, and Control Transformers 2.4 Conductors, Insulators, Wire Sizing, Voltage Drop, and NEC Ampacity

3 Chapter 3: Electrical Components, Motors, and Schematics

3.1 Contactors, Relays, Switches, Overload Protection, and Thermostats 3.2 HVAC Motors (PSC, CSIR, CSCR, ECM, 3-Phase) and Run/Start Capacitors 3.3 Interpreting Ladder Diagrams, Schematics, and Point-to-Point Wiring 3.4 Motor Testing, Insulation Resistance, Bearings, and Belt Drives

4 Chapter 4: Thermodynamics and the Refrigeration Cycle

4.1 Heat Transfer, Temperature Scales, BTUs, Sensible vs Latent Heat, and Enthalpy 4.2 The Four Vapor-Compression Cycle Stages (Compression, Condensation, Expansion, Evaporation) 4.3 P-T Charts, Saturated Conditions, Target Superheat, and Subcooling Calculations 4.4 Pressure–Enthalpy Diagrams, Compression Ratio, and Cycle Analysis

5 Chapter 5: Refrigerants, Environmental Regulations, and Recovery

5.1 Refrigerant Types (CFC, HCFC, HFC, HFO, HC) and ASHRAE Safety Groups (A1, A2L, A3) 5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards 5.3 Recovery/Recycling/Reclaiming Equipment, Procedures, and Leak Detection 5.4 Refrigerant Retrofits, Cylinder Handling, and Refrigerant Purity 5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice

6 Chapter 6: Refrigeration System Components and Accessories

6.1 Compressor Mechanics (Reciprocating, Scroll, Rotary, Screw) and Failures 6.2 Expansion Devices (TXV/TEV, Fixed Orifice, EEV) and Superheat Control 6.3 Condensers, Evaporators, Filter-Driers, Accumulators, Receivers, and Solenoids 6.4 Pressure Controls, Capacity Controls, and System Protection 6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice

7 Chapter 7: Gas Heating, Combustion Analysis, and Fuel Piping

7.1 Combustion Theory, Fuel Gases (Natural Gas vs LP), and Gas Burners 7.2 Gas Valves, Ignition Systems (Standing Pilot, Spark, HSI), and Safety Limit Controls 7.3 Flue Venting, Draft Principles, Combustion Analysis, and CO Safety 7.4 Fuel-Gas and Oil Piping, Vent System Selection and Sizing, and Installation Practice

8 Chapter 8: Electric Heating, Oil Heat, and Hydronics

8.1 Electric Heating Elements, Sequencers, Limit Switches, and kW Calculations 8.2 Oil Burners, Fuel Pumps, Nozzles, Ignition Electrodes, and Primary Controls 8.3 Hydronic Boilers, Circulator Pumps, Expansion Tanks, and Zone Controls 8.4 Combustion Air, Water Heaters, and Combustion Appliance Zone Testing

9 Chapter 9: Heat Pumps and Dual-Fuel Systems

9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation 9.2 Defrost Controls (Time-Temperature, Demand Defrost), Sensors, and Sequences 9.3 Balance Points, Auxiliary/Emergency Heat, and Dual-Fuel (Hybrid) Systems 9.4 Heat Pump Diagnostics, Refrigerant Flow, and Troubleshooting Procedures 9.5 Heat Pump Types, Cold-Climate Performance, and Sizing Approaches

10 Chapter 10: Air Distribution, IAQ, and System Commissioning

10.1 Airflow Fundamentals, CFM Measurement, External Static Pressure, and Fan Laws 10.2 Duct Sizing Principles, Supply/Return Distribution, Dampers, and Air Balancing 10.3 Indoor Air Quality, MERV Ratings, Electronic Cleaners, Humidification, and Dehumidification 10.4 Deep Vacuum Evacuation (Micron Gauge), Subcooling/Superheat Charging, and System Commissioning 10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance

11 Chapter 11: Psychrometrics, Airside Calculations, and Load Estimation

11.1 Reading the Psychrometric Chart: Properties and Plotting 11.2 The Eight Air-Conditioning Processes and the Process Triangle 11.3 Mixed Air, Ventilation, and Infiltration Calculations 11.4 Residential Heat Loss, Heat Gain, and Equipment Sizing

12 Chapter 12: Light Commercial Air Conditioning

12.1 Packaged Rooftop and Split Light-Commercial Systems 12.2 Water-Cooled Condensers, Cooling Towers, and Chilled-Water Systems 12.3 Economizers, Demand-Controlled Ventilation, and VAV Air Distribution 12.4 Light-Commercial Start-Up, Commissioning, and Troubleshooting

13 Chapter 13: Light Commercial Refrigeration

13.1 Temperature Ranges, Box Loads, and Refrigeration System Types 13.2 Evaporators, Defrost Methods, and Defrost Controls 13.3 Condensing Units, Parallel Racks, Oil Management, and Capacity Control 13.4 Refrigeration Control Valves and Automatic Pump-Down 13.5 Commercial Refrigeration Diagnostics and Ice Machines

14 Chapter 14: Ductless, Mini-Split, and VRF Systems

14.1 Mini-Split Architecture and Inverter-Driven Compressors 14.2 Multi-Zone and VRF Operation, Electronic Expansion Valves, and Controls 14.3 Ductless Installation, Evacuation, Charging, and Diagnostics

15 Chapter 15: Building Automation and Digital Controls

15.1 DDC Fundamentals, Control Loops, and Sequences of Operation 15.2 BAS Networks, Protocols, and NEC-Compliant Cabling 15.3 Building Automation Controllers: Supervisory, Field, and Room Devices 15.4 Digital Logic, Numbering Systems, and Controller Programming 15.5 Sensor Selection, Installation, and Input Point Configuration 15.6 Actuators, Output Devices, and VFD Integration 15.7 Commercial Prints, Equipment Schedules, and BAS Documentation

5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards

Key Takeaways Explain This Topic AI

Technician certification is divided into four distinct categories: Type I (small appliances ≤ 5 lbs), Type II (medium-, high- and very high-pressure appliances other than small appliances), Type III (low-pressure systems), and Universal (all three types combined).

Under 40 CFR 82.156 Table 1 (post-1993 recovery equipment), high-pressure appliances under 200 lb need 0" Hg, high-pressure appliances of 200 lb or more and medium-pressure appliances under 200 lb need 10" Hg, medium-pressure appliances of 200 lb or more need 15" Hg, and low-pressure chillers need 25 mm Hg absolute (approx. 29" Hg vacuum).

EPA leak repair trigger rates for appliances containing 50+ lbs of ozone-depleting refrigerant are 10% for Comfort Cooling, 20% for Commercial Refrigeration, and 30% for Industrial Process Refrigeration, requiring initial and 30-day follow-up verification tests.

Technicians and facilities must maintain leak inspection logs, initial/follow-up test records, and refrigerant addition invoices for a minimum of 3 years.

Since January 1, 2026, the AIM Act subsection (h) rule (40 CFR 84.106) applies leak repair, verification and recordkeeping to appliances holding 15 pounds or more of an HFC or substitute with GWP above 53 — a lower threshold than the 50-pound Section 608 rule for ozone-depleting refrigerants.

Last updated: October 2026

5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards

Title VI of the federal Clean Air Act (42 U.S. Code § 7671g) empowers the United States Environmental Protection Agency (EPA) to regulate the handling, recovery, recycling, emission reduction, and disposal of ozone-depleting substances and their non-exempt substitutes. Enacted under EPA Section 608 (codified in 40 CFR Part 82, Subpart F) , these federal regulations establish strict legal obligations for every HVACR technician, contractor, and equipment owner. Violations carry severe civil penalties. The maximum per-day, per-violation amount is set by statute and then re-published every year under EPA's Civil Monetary Penalty Inflation Adjustment Rule, so it climbs continuously — it has moved from $25,000 in the original statute to well over $60,000 per day per violation under recent adjustment tables. Do not memorize a dollar figure; know that the penalty is assessed per day and per violation , that it is inflation-adjusted annually, and that willful violations can also be prosecuted criminally.

1. The Statutory Venting Prohibition and De Minimis Exceptions

The cornerstone of EPA Section 608 is the Venting Prohibition . +-------------------------------------------------------------------------+

  • | THE EPA SECTION 608 VENTING MANDATE |
  • +-------------------------------------------------------------------------+
  • | "No person maintaining, servicing, repairing, or disposing of an |
  • | appliance may knowingly vent or otherwise release into the environment |
  • | any Class I (CFC) or Class II (HCFC) substance, or any non-exempt |
  • | substitute refrigerant (including HFCs, HFOs, and their blends)." |
  • +-------------------------------------------------------------------------+
  • Scope of Regulated vs. Exempt Refrigerants

Regulated Substances (Venting is Illegal): CFCs (R-11, R-12), HCFCs (R-22, R-123), HFCs (R-410A, R-134a, R-404A, R-32), HFOs (R-1234yf, R-454B), and all synthetic multi-component blends.

De Minimis Release Exemption: The EPA recognizes that minor, incidental releases of refrigerant cannot be 100% avoided during standard field service. A release is classified as de minimis (and therefore legal) only when it occurs during good-faith attempts to recover, recycle, or properly transfer refrigerant using EPA-certified recovery equipment and hoses equipped with low-loss fittings (shut-off valves or core depressors located within 12 inches 12\text{ inches} 12 inches of the hose termination).

Exempt Refrigerants (May be legally vented): Refrigerants that the EPA Administrator has formally determined pose no threat to the stratospheric ozone layer and have negligible global warming impact under SNAP. These include:

  • Pure Carbon Dioxide ( R − 744 R-744 R − 744 / C O 2 CO_2 C O 2 ​ )
  • Pure Nitrogen ( N 2 N_2 N 2 ​ ) and compressed dry air (used as holding/leak testing charges)
  • Pure Water ( R − 718 R-718 R − 718 )

Small quantities of Hydrocarbons (R-290 Propane, R-600a Isobutane) used in hermetically sealed small appliances within approved EPA SNAP charge limits.

Loading diagram... EPA Section 608 Technician Certification Hierarchy

2. EPA Section 608 Technician Certification Classifications

Technicians must pass a proctored examination administered by an EPA-approved testing organization (such as the ESCO Group / HVAC Excellence) to service or purchase regulated refrigerants. The certification is divided into four distinct credentials:

1. Core Component (Prerequisite)

Covers environmental impact, stratospheric ozone depletion, global warming, Clean Air Act provisions, Section 608 rules, Montreal Protocol, substitute refrigerants, recovery techniques, dehydration evacuation principles, safety standards, and cylinder shipping regulations. A technician must pass Core plus at least one specialty type to earn a valid certification card.

2. Type I Certification: Small Appliances

Appliance Scope: Equipment manufactured, charged, and hermetically sealed in a factory containing 5 pounds 5\text{ pounds} 5 pounds or less of refrigerant .

Covered Equipment: Domestic refrigerators, domestic freezers, room air conditioners, packaged terminal air conditioners (PTACs), packaged terminal heat pumps (PTHPs), drinking water coolers, and small commercial reach-in beverage coolers.

Field Protocol: Technicians may use passive (system-dependent) recovery equipment that relies on the appliance's internal compressor, or active (self-contained) recovery equipment. Piercing valves (saddle valves) are permitted on process tubes but must be leak-tested and should ideally be replaced with permanent brazed access ports.

3. Type II Certification: Medium-, High- and Very High-Pressure Appliances

Appliance Scope: Medium-, high- and very high-pressure appliances other than small appliances and MVACs (40 CFR 82.161). EPA classes them by the refrigerant's liquid-phase saturation pressure at 104 °F: medium-pressure 45 to 170 psia (R-12, R-134a, R-500), high-pressure 170 to 355 psia (R-22, R-407C, R-410A), very high-pressure above 355 psia (R-13, R-23, R-503).

Covered Equipment: Residential central air conditioners, split-system heat pumps, light commercial rooftop packages, multi-zone VRF/VRV systems, commercial walk-in coolers, and supermarket rack refrigeration systems using R-410A, R-454B, R-22, R-134a, R-404A, and R-32.

4. Type III Certification: Low-Pressure Appliances

Appliance Scope: Systems whose refrigerant has a liquid-phase saturation pressure below 45 psia at 104 °F (40 CFR 82.152), which operate under a vacuum in the evaporator.

Covered Equipment: Large industrial and commercial centrifugal chillers using low-pressure refrigerants such as R-11, R-123, and R-1233zd .

Specialized Operating Mechanics:

Evaporators operate in a vacuum (e.g., R-123 boils at 82 ∘ F 82^\circ\text{F} 8 2 ∘ F at 0 psig 0\text{ psig} 0 psig ; at 40 ∘ F 40^\circ\text{F} 4 0 ∘ F evaporator temperature, pressure is 18.1 in. Hg vacuum 18.1\text{ in. Hg vacuum} 18.1 in. Hg vacuum ). Air and non-condensables leak inward through gaskets, requiring an active purge unit to vent air from the condenser top.

Primary pressure relief protection is a rupture disc set to burst at 15 psig 15\text{ psig} 15 psig .

To prevent freezing the water inside chiller heat exchanger tubes during evacuation, the chilled-water and condenser-water circulating pumps must run continuously , and the system must be charged with vapor until internal pressure exceeds the freezing point of water ( 32 ∘ F 32^\circ\text{F} 3 2 ∘ F saturation pressure, e.g., 16.9 in. Hg vacuum 16.9\text{ in. Hg vacuum} 16.9 in. Hg vacuum / 6.5 psia 6.5\text{ psia} 6.5 psia for R-123) before introducing liquid refrigerant.

5. Universal Certification

Awarded to technicians who successfully pass all four sections: Core, Type I, Type II, and Type III . Universal technicians are certified to maintain, service, recover, and dispose of all stationary refrigeration equipment across residential, commercial, and industrial sectors.

3. Required Evacuation Levels for System Recovery

When recovering refrigerant prior to opening a refrigeration system for service (such as replacing a compressor, filter-drier, or TXV), technicians must pull the system down to specific vacuum levels mandated by the EPA. These levels depend on the equipment type, total charge, and the date of manufacture of the recovery equipment. +------------------------------------------------------------------------------------------------+

  • | EPA MANDATED REFRIGERANT EVACUATION LEVELS |
  • +-------------------------------------------------------------+-------------------+--------------+
  • | Appliance Category & Operating Pressure | Recovery Unit | Recovery Unit|
  • | | Mfg BEFORE | Mfg ON/AFTER |
  • | | Nov 15, 1993 | Nov 15, 1993 |
  • +-------------------------------------------------------------+-------------------+--------------+
  • | Small Appliance (Type I) with OPERATING Compressor | 80% charge | 90% charge |
  • | (or pull down to 4" Hg vacuum) | | (or 4" Hg) |
  • +-------------------------------------------------------------+-------------------+--------------+
  • | Small Appliance (Type I) with INOPERATIVE Compressor | 80% charge | 80% charge |
  • | (or pull down to 4" Hg vacuum) | | (or 4" Hg) |
  • +-------------------------------------------------------------+-------------------+--------------+
  • | High-Pressure Appliance: Less than 200 lbs charge | 0" Hg (0 psig) | 0" Hg |
  • | (R-22, R-407C, R-410A, R-502) | | |
  • +-------------------------------------------------------------+-------------------+--------------+
  • | High-Pressure Appliance: 200 lbs or MORE charge | 4" Hg vac | 10" Hg vac |
  • +-------------------------------------------------------------+-------------------+--------------+
  • | Medium-Pressure Appliance: Less than 200 lbs charge | 4" Hg vac | 10" Hg vac |
  • | (R-12, R-114, R-124, R-134a, R-500) | | |
  • +-------------------------------------------------------------+-------------------+--------------+
  • | Medium-Pressure Appliance: 200 lbs or MORE charge | 4" Hg vac | 15" Hg vac |
  • +-------------------------------------------------------------+-------------------+--------------+
  • | Very High-Pressure Appliance (R-13, R-23, R-503) | 0" Hg (0 psig) | 0" Hg |
  • +-------------------------------------------------------------+-------------------+--------------+
  • | Low-Pressure Appliance (Type III Chiller: R-11, R-123) | 25 mm Hg abs | 25 mm Hg abs |
  • +-------------------------------------------------------------+-------------------+--------------+
  • Key Evacuation Exceptions and Code Rules

Pressure class, not refrigerant name. Current Table 1 in 40 CFR 82.156 has no separate HCFC-22 row: a high-pressure appliance (R-22, R-407C, R-410A) under 200 lb needs 0 inches Hg regardless of recovery-machine age , while a medium-pressure appliance (R-12, R-134a, R-500) under 200 lb needs 10 inches Hg with post-1993 equipment.

Systems with Verified Leaks: If leaks make the Table 1 level unattainable or would substantially contaminate the recovered refrigerant, isolate leaking from non-leaking components where possible, evacuate the non-leaking components to the Table 1 level, and evacuate the leaking components to the lowest level attainable without substantially contaminating the refrigerant, which may not exceed 0 psig (40 CFR 82.156(a)(2)).

Major vs. Non-Major Repairs (EPA Definition):

Major Repair: Any service or maintenance involving the removal or replacement of the compressor, condenser coil, evaporator coil, or auxiliary heat exchanger coil .

Non-Major Repair: Replacement of external accessories such as filter-driers, TXVs, pressure switches, or solenoid valves.

Loading diagram... EPA Section 608 Leak Repair Decision Tree (40 CFR Part 82)

4. EPA Leak Repair Regulations and Trigger Rates (40 CFR Part 82 Subpart F)

There are now two parallel leak-repair rules , and knowing which one applies to the appliance in front of you is the current high-value exam skill.

Rule Legal basis Refrigerants covered Charge threshold

Section 608 leak repair Clean Air Act Title VI, 40 CFR Part 82 Subpart F Ozone-depleting refrigerants (CFCs and HCFCs such as R-11, R-12, R-22, R-123) 50 lb or more

AIM Act leak repair AIM Act subsection (h), 40 CFR 84.106 — the 2024 Emissions Reduction and Reclamation rule, compliance date January 1, 2026 HFCs and HFC substitutes with GWP greater than 53 (R-410A, R-404A, R-134a, R-32, R-454B and similar) 15 lb or more

Both rules impose leak inspection, repair, verification testing, and recordkeeping on the owner or operator of the appliance. The AIM Act rule dropped the trigger from 50 lb to 15 lb, which pulled tens of thousands of previously exempt walk-in coolers, small rooftop units, and process chillers into the program. Residential and light-commercial air conditioning and heat pumps are excluded from the 40 CFR 84.106 leak-repair requirements.

Annualized Leak Rate Trigger Thresholds

The sector-based percentage triggers are identical under both rules — only the charge threshold and the covered refrigerants differ. If a covered appliance leaks at a rate above the applicable threshold, the owner or operator is legally required to repair it:

Appliance Sector Definition & Application Annual Leak Rate Trigger Threshold

Comfort Cooling Air conditioning systems used primarily to cool occupied spaces in commercial, residential, and institutional buildings (e.g., office chillers, residential rooftop packages). 10%

Commercial Refrigeration Refrigeration equipment used in the retail food and cold storage warehouse sectors (e.g., supermarket parallel compressor racks, walk-in freezers). 20%

Industrial Process Refrigeration (IPR) Complex refrigeration systems directly integrated into industrial manufacturing processes (e.g., chemical plants, petroleum refineries, pharmaceutical synthesis, food manufacturing). 30%

Calculating the Annualized Leak Rate

Technicians calculate the leak rate upon adding refrigerant using the Rolling Average Method or the Annualized Method : Leak Rate (%) = ( Refrigerant Added (lbs) Full System Charge (lbs) ) × ( 365 Days Since Last Refrigerant Addition ) × 100 % \text{Leak Rate (\%)} = \left( \frac{\text{Refrigerant Added (lbs)}}{\text{Full System Charge (lbs)}} \right) \times \left( \frac{365}{\text{Days Since Last Refrigerant Addition}} \right) \times 100\% Leak Rate (%) = ( Full System Charge (lbs) Refrigerant Added (lbs) ​ ) × ( Days Since Last Refrigerant Addition 365 ​ ) × 100%

Example: A supermarket commercial refrigeration rack with a full charge of 800 lbs 800\text{ lbs} 800 lbs has 50 lbs 50\text{ lbs} 50 lbs of R-404A added 90 days 90\text{ days} 90 days after its last service: Leak Rate = ( 50 800 ) × ( 365 90 ) × 100 % = 0.0625 × 4.055 × 100 % = 25.35 % \text{Leak Rate} = \left( \frac{50}{800} \right) \times \left( \frac{365}{90} \right) \times 100\% = 0.0625 \times 4.055 \times 100\% = 25.35\% Leak Rate = ( 800 50 ​ ) × ( 90 365 ​ ) × 100% = 0.0625 × 4.055 × 100% = 25.35%

Evaluation: 25.35 % 25.35\% 25.35% exceeds the 20 % 20\% 20% commercial refrigeration threshold, so the owner must execute mandatory repairs. Note that this rack would be covered under both rules if it still held R-22, and under the AIM Act rule now that it holds R-404A — the 800 lb charge is far above the 15 lb HFC threshold, and at 800 lb it sits below the 1,500 lb automatic-leak-detection trigger.

Mandatory Repair Timelines and Verification Testing

30-Day Repair Window: The leak must be repaired within 30 calendar days 30\text{ calendar days} 30 calendar days of discovering the leak rate exceedance (extended to 120 days for IPR if an industrial shutdown is required).

Initial Leak Verification Test: Must be performed before recharging or immediately upon completing the repair (e.g., standing nitrogen pressure decay test, vacuum hold test, or electronic leak sniffing of repaired joints) before introducing the full operating charge.

Follow-Up Leak Verification Test: Must be performed within 30 days 30\text{ days} 30 days of the system returning to normal operating temperature and pressure conditions . This verifies that the repair holds under true operating thermal expansion, vibration, and hydraulic pressures.

Failure to Repair: If either verification test fails, the owner must re-repair within the original 30 days or develop an EPA-compliant 1-Year Retrofit or Retirement Plan .

Automatic leak detection (AIM Act, 40 CFR 84.108)

The AIM Act rule adds a requirement that Section 608 never had. Industrial process refrigeration and commercial refrigeration appliances with a full charge of 1,500 lb or more of an HFC or substitute with GWP above 53 must have an automatic leak detection (ALD) system — continuous monitoring that alarms on a detected leak rather than waiting for a scheduled inspection.

New appliances: ALD required from January 1, 2026 (installed within 30 days of appliance installation).

Existing appliances: ALD required by January 1, 2027 .

Manual leak inspections still apply to covered appliances between 15 lb and 1,499 lb; ALD does not replace the leak-rate calculation or the 30-day repair clock.

  • 5. Recordkeeping and Equipment Disposal Mandates
  • 3-Year Record Retention Mandate

Service Records: Technicians, contractors, and facility operators must maintain detailed service logs for a minimum of 3 years 3\text{ years} 3 years — for appliances holding 50 lbs 50\text{ lbs} 50 lbs or more of an ozone-depleting refrigerant under 40 CFR Part 82 Subpart F, and for appliances holding 15 lbs 15\text{ lbs} 15 lbs or more of an HFC or substitute with GWP above 53 under 40 CFR 84.106.

Required Log Data: Date of service, technician name and EPA certification ID, exact quantity of refrigerant added, quantity recovered, full system charge capacity, calculated leak rate, and detailed results of both initial and follow-up leak verification tests.

Small Appliance and Disposal Tracking (5 to 50 lbs)

For appliances containing between 5 5 5 and 50 lbs 50\text{ lbs} 50 lbs of refrigerant , equipment disposal facilities and technicians must maintain records documenting:

The date of disposal.

Equipment model and serial number.

Total quantity of refrigerant recovered from each unit prior to metal scrapping.

Safe Disposal Requirement: The final person in the disposal chain (e.g., scrap metal recycler, landfill operator) is legally responsible for ensuring that all refrigerant has been evacuated to mandated recovery levels before crushing or shredding equipment.