Study guide
6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice
HVAC Excellence Certification Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction, Safety, Tools, and Diagnostic Method
1.1 HVAC Excellence Certification, Industry Codes, and Standards 1.2 Electrical Safety, PPE, Lockout/Tagout, and Hazard Communication 1.3 Multimeters, Manifold Gauges, Micron Gauges, and Diagnostic Instruments 1.4 HVACR Mathematics, Unit Conversions, and Efficiency Ratings 1.5 OSHA Standards, Fall Protection, Rigging, and Confined Spaces 1.6 HVACR Industry Organizations, Energy Resources, and Building Energy Programs 1.7 Systematic Troubleshooting: Data Plates, Manufacturer Literature, and Diagnostic Method
2 Chapter 2: Electrical Fundamentals and Circuit Theory
2.1 Voltage, Current, Resistance, and Ohm's Law Calculations 2.2 Series, Parallel, and Series-Parallel Circuits and Power Calculations 2.3 AC Fundamentals, Single-Phase vs Three-Phase Power, and Control Transformers 2.4 Conductors, Insulators, Wire Sizing, Voltage Drop, and NEC Ampacity
3 Chapter 3: Electrical Components, Motors, and Schematics
3.1 Contactors, Relays, Switches, Overload Protection, and Thermostats 3.2 HVAC Motors (PSC, CSIR, CSCR, ECM, 3-Phase) and Run/Start Capacitors 3.3 Interpreting Ladder Diagrams, Schematics, and Point-to-Point Wiring 3.4 Motor Testing, Insulation Resistance, Bearings, and Belt Drives
4 Chapter 4: Thermodynamics and the Refrigeration Cycle
4.1 Heat Transfer, Temperature Scales, BTUs, Sensible vs Latent Heat, and Enthalpy 4.2 The Four Vapor-Compression Cycle Stages (Compression, Condensation, Expansion, Evaporation) 4.3 P-T Charts, Saturated Conditions, Target Superheat, and Subcooling Calculations 4.4 Pressure–Enthalpy Diagrams, Compression Ratio, and Cycle Analysis
5 Chapter 5: Refrigerants, Environmental Regulations, and Recovery
5.1 Refrigerant Types (CFC, HCFC, HFC, HFO, HC) and ASHRAE Safety Groups (A1, A2L, A3) 5.2 EPA Section 608 Regulations, Venting Prohibitions, and Evacuation Standards 5.3 Recovery/Recycling/Reclaiming Equipment, Procedures, and Leak Detection 5.4 Refrigerant Retrofits, Cylinder Handling, and Refrigerant Purity 5.5 A2L and Low-GWP Refrigerants: Codes, Charge Limits, and Service Practice
6 Chapter 6: Refrigeration System Components and Accessories
6.1 Compressor Mechanics (Reciprocating, Scroll, Rotary, Screw) and Failures 6.2 Expansion Devices (TXV/TEV, Fixed Orifice, EEV) and Superheat Control 6.3 Condensers, Evaporators, Filter-Driers, Accumulators, Receivers, and Solenoids 6.4 Pressure Controls, Capacity Controls, and System Protection 6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice
7 Chapter 7: Gas Heating, Combustion Analysis, and Fuel Piping
7.1 Combustion Theory, Fuel Gases (Natural Gas vs LP), and Gas Burners 7.2 Gas Valves, Ignition Systems (Standing Pilot, Spark, HSI), and Safety Limit Controls 7.3 Flue Venting, Draft Principles, Combustion Analysis, and CO Safety 7.4 Fuel-Gas and Oil Piping, Vent System Selection and Sizing, and Installation Practice
8 Chapter 8: Electric Heating, Oil Heat, and Hydronics
8.1 Electric Heating Elements, Sequencers, Limit Switches, and kW Calculations 8.2 Oil Burners, Fuel Pumps, Nozzles, Ignition Electrodes, and Primary Controls 8.3 Hydronic Boilers, Circulator Pumps, Expansion Tanks, and Zone Controls 8.4 Combustion Air, Water Heaters, and Combustion Appliance Zone Testing
9 Chapter 9: Heat Pumps and Dual-Fuel Systems
9.1 Heat Pump Operation in Heating/Cooling Modes and Reversing Valve Operation 9.2 Defrost Controls (Time-Temperature, Demand Defrost), Sensors, and Sequences 9.3 Balance Points, Auxiliary/Emergency Heat, and Dual-Fuel (Hybrid) Systems 9.4 Heat Pump Diagnostics, Refrigerant Flow, and Troubleshooting Procedures 9.5 Heat Pump Types, Cold-Climate Performance, and Sizing Approaches
10 Chapter 10: Air Distribution, IAQ, and System Commissioning
10.1 Airflow Fundamentals, CFM Measurement, External Static Pressure, and Fan Laws 10.2 Duct Sizing Principles, Supply/Return Distribution, Dampers, and Air Balancing 10.3 Indoor Air Quality, MERV Ratings, Electronic Cleaners, Humidification, and Dehumidification 10.4 Deep Vacuum Evacuation (Micron Gauge), Subcooling/Superheat Charging, and System Commissioning 10.5 Duct Leakage, Blower Door Testing, and Building Envelope Performance
11 Chapter 11: Psychrometrics, Airside Calculations, and Load Estimation
11.1 Reading the Psychrometric Chart: Properties and Plotting 11.2 The Eight Air-Conditioning Processes and the Process Triangle 11.3 Mixed Air, Ventilation, and Infiltration Calculations 11.4 Residential Heat Loss, Heat Gain, and Equipment Sizing
12 Chapter 12: Light Commercial Air Conditioning
12.1 Packaged Rooftop and Split Light-Commercial Systems 12.2 Water-Cooled Condensers, Cooling Towers, and Chilled-Water Systems 12.3 Economizers, Demand-Controlled Ventilation, and VAV Air Distribution 12.4 Light-Commercial Start-Up, Commissioning, and Troubleshooting
13 Chapter 13: Light Commercial Refrigeration
13.1 Temperature Ranges, Box Loads, and Refrigeration System Types 13.2 Evaporators, Defrost Methods, and Defrost Controls 13.3 Condensing Units, Parallel Racks, Oil Management, and Capacity Control 13.4 Refrigeration Control Valves and Automatic Pump-Down 13.5 Commercial Refrigeration Diagnostics and Ice Machines
14 Chapter 14: Ductless, Mini-Split, and VRF Systems
14.1 Mini-Split Architecture and Inverter-Driven Compressors 14.2 Multi-Zone and VRF Operation, Electronic Expansion Valves, and Controls 14.3 Ductless Installation, Evacuation, Charging, and Diagnostics
15 Chapter 15: Building Automation and Digital Controls
15.1 DDC Fundamentals, Control Loops, and Sequences of Operation 15.2 BAS Networks, Protocols, and NEC-Compliant Cabling 15.3 Building Automation Controllers: Supervisory, Field, and Room Devices 15.4 Digital Logic, Numbering Systems, and Controller Programming 15.5 Sensor Selection, Installation, and Input Point Configuration 15.6 Actuators, Output Devices, and VFD Integration 15.7 Commercial Prints, Equipment Schedules, and BAS Documentation
6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice
Key Takeaways Explain This Topic AI
Suction lines are sized for a pressure drop equivalent to about 2 degrees Fahrenheit of saturation change, and liquid lines for about 1 to 2 degrees, not for a fixed velocity alone.
Minimum gas velocity for oil return is roughly 750 FPM in horizontal suction lines and 1,500 FPM in vertical risers, which is why oversized suction lines cause oil logging.
Brazing alloys with 15% silver phosphorus (BCuP-5) are self-fluxing on copper-to-copper joints but require flux on copper-to-brass or copper-to-steel.
Flowing 2 to 3 psig of dry nitrogen through tubing during brazing prevents cupric oxide scale that would otherwise plug metering devices and filter-driers.
A 45-degree SAE flare is the standard mechanical connection on mini-splits; the flare is made after deburring, with the tube nut installed first and the flare lubricated with refrigerant oil.
Last updated: August 2026
6.5 Refrigerant Line Sizing, Pressure Drop, Brazing, and Piping Practice
"Sizing, designing, and installing refrigerant lines," "determine refrigerant line pressure drop and explain the effects of pressure drop on a system," "soldering and brazing using correct techniques," "explaining the proper use and handling of nitrogen," and "flaring" all appear as competencies on the HVAC Excellence task list. Piping is the part of the trade where a technician's decisions are permanently embedded in the building.
1. Why Line Size Is Not About Fitting the Stub
Every refrigerant line has two competing requirements:
Low pressure drop , so the compressor does not have to work against friction.
High enough velocity , so oil entrained in the refrigerant is carried back to the compressor.
Undersize the line and you get excessive pressure drop. Oversize it and velocity falls below the point where the vapor can drag oil up a riser, and oil logs in the evaporator. A line that is too large is as much a failure as one that is too small , which is why "the size of the stub-out" is never the sizing method.
Pressure drop criteria (expressed in saturation temperature)
The industry sizes lines by the equivalent saturation temperature change the pressure drop causes, because that is what actually affects capacity.
- Line Typical design pressure drop
- Suction line 2°F equivalent saturation change
- Discharge (hot gas) line 2°F equivalent saturation change
- Liquid line 1–2°F equivalent, and never enough to flash
Suction line pressure drop is the expensive one. Each 2°F of suction-line saturation loss costs roughly 3–5% of system capacity and raises compressor power draw, because the compressor must pull down to a lower pressure to hold the same evaporator temperature.
Liquid line pressure drop is dangerous rather than merely costly. If total liquid-line pressure drop (friction plus vertical lift) exceeds the available subcooling, the liquid flashes to vapor before reaching the metering device . A TXV fed with flash gas hunts, starves the coil, and produces high superheat with a low-capacity system that looks undercharged but is not. Every foot of vertical lift costs about 0.5 psi on common refrigerants — a 30-foot riser costs roughly 15 psi, which on R-410A is worth several degrees of subcooling.
Velocity criteria for oil return
- Location Minimum velocity
- Horizontal suction and discharge lines ≈ 750 FPM
- Vertical risers (upflow) ≈ 1,500 FPM
- Liquid lines (maximum, to limit erosion and noise) ≈ 300 FPM (roughly 100–300 FPM design)
Double suction risers solve the conflict on systems with capacity control. Two risers are run in parallel with a trap at the bottom of the larger one. At full load both carry gas. At part load, oil collects in the trap and seals the large riser, forcing all flow through the small one, which restores velocity. This is a classic exam topic on unloading compressors and multi-evaporator racks.
Traps and slopes
Trap the bottom of every suction riser and, on tall risers, add an intermediate trap roughly every 20 feet so the vapor is not asked to lift an unbroken oil column.
Slope horizontal suction lines toward the compressor , roughly 1/2 inch per 10 feet, so gravity assists oil return.
An inverted trap at the evaporator outlet , rising above the top of the coil, prevents liquid from draining into the compressor during the off cycle on a system without pump-down.
Never trap a liquid line ; there is no oil-return need and a trap only adds pressure drop.
Support tubing at code intervals, isolate it from structure with grommets or clamps that allow thermal movement, and insulate the suction line (and, on heat pumps, both lines) with closed-cell insulation of adequate wall thickness.
- 2. Brazing and Soldering
- The distinction
- Soldering Brazing
- Filler melting point Below 840°F Above 840°F
- Typical alloy 95/5 tin-antimony, tin-silver BCuP (copper-phosphorus), BAg (silver)
- Joint strength Lower Much higher
- HVACR use Water lines, condensate All refrigerant lines
Refrigerant joints are brazed , not soldered. Soft-soldered refrigerant joints fail under vibration and pressure.
Choosing the alloy
BCuP-2 (0% silver) and BCuP-5 (15% silver) are self-fluxing on copper-to-copper joints, because the phosphorus reduces copper oxide as it flows. Never use a phosphorus-bearing alloy on ferrous metal , and never on copper-to-nickel or copper-to-steel — brittle phosphides form.
Copper-to-brass and copper-to-steel joints (service valves, accumulators, driers with steel shells) require a silver alloy (BAg series) with flux .
Higher silver content lowers the melting range and increases ductility and gap-filling ability — useful on close-tolerance or dissimilar-metal joints.
Technique
Cut square with a tubing cutter, then deburr inside and out. Burrs create turbulence and shed copper into the system.
Clean the tube end and the fitting socket with an abrasive cloth or nylon pad. Do not use steel wool or emery containing oil.
Fit-up matters: capillary action pulls filler into a gap of roughly 0.001–0.005 inch . Too tight and filler will not enter; too loose and it will not bridge.
Purge with nitrogen. Flow 2–3 psig of dry nitrogen (a trickle you can barely feel) through the tubing throughout heating and until the joint cools. Without it, oxygen inside the tube reacts with hot copper to form cupric oxide scale , a black flake that breaks loose later and plugs metering devices, screens, and driers. Provide an exit for the nitrogen — never braze a fully closed system under nitrogen pressure.
Heat the base metal, not the filler. Heat the fitting and the tube evenly until the copper reaches a dull cherry red, then touch the filler to the joint on the side opposite the flame and let capillary action pull it in.
Protect nearby components. Wrap TXV bodies, service valves, and Schrader cores with a wet rag or heat-blocking paste, or remove valve cores entirely — a heated core melts and the valve leaks forever.
Wipe or quench the finished joint only after the filler has solidified, and inspect for a continuous fillet all the way around.
Safety recap
Recover refrigerant first (Section 1.5), ventilate, use cadmium-free alloys, keep a fire watch for 30 minutes, secure and cap cylinders, and keep oxygen away from oil.
3. Mechanical Joints: Flaring and Swaging
Mini-splits, some metering devices, and many service connections use 45° SAE flares .
Making a good flare
Cut square and deburr — a burr becomes a leak path.
Slide the flare nut on first. Forgetting this is the classic rework.
Clamp the tube in the flaring block with the correct amount protruding (roughly the thickness of the tubing wall above the block face for a standard yoke, or per the tool's gauge).
Apply a drop of refrigeration oil to the cone; it lubricates the burnishing action and produces a smoother, more uniform flare. (Use the same oil as the system — POE for HFC systems.)
Turn the yoke smoothly; back off and re-advance to burnish. Stop before the flare cracks or thins.
Inspect: the flare face should be smooth, concentric, and free of cracks or scoring, with the full width bearing on the fitting seat.
Torque to specification. Mini-split manufacturers publish flare torque values (for example, roughly 10–12 ft-lb for 1/4", 25–27 ft-lb for 3/8", 35–40 ft-lb for 1/2"). Over-torquing splits the flare; under-torquing leaks. Use a torque wrench, and back up the fitting with a second wrench.
Swaging expands one tube end to accept another of the same size, eliminating a coupling. Anneal work-hardened tube with heat if it resists, expand to a depth of at least the tube diameter, and braze the joint normally.
4. Pressure Testing and Leak-Test Pressures
The Commercial sheets specifically list "system leak-test pressures and nitrogen regulator installation and adjustment" as a safety competency.
Always use a two-stage regulator with a relief valve on the nitrogen cylinder. A full nitrogen cylinder exceeds 2,000 psig; connecting it to a system without a regulator will rupture the lowest-rated component, usually the evaporator or a compressor shell, with lethal force.
Test pressure is set by the equipment's low-side and high-side design pressures marked on the nameplate — never a personal habit. Isolate the compressor and any component whose rating is below the test pressure.
Never pressure-test with oxygen — it forms an explosive mixture with refrigerant oil — and never with acetylene, compressed air (moisture), or refrigerant plus nitrogen as a "trace gas" for detection, which is prohibited for regulated refrigerants because it constitutes venting when released.
Standing pressure decay test: pressurize, record pressure and ambient temperature , wait, and re-read both. Pressure changes with temperature even in a perfectly tight system — roughly 0.5 psi per °F on a typical system volume — so a decay test without a temperature reading proves nothing.
After a successful pressure test, release nitrogen slowly, then evacuate to 500 microns with a micron gauge and confirm with a decay test (Section 10.4).