Study guide

7.3 Gas Pipe Materials, Joining, CSST Rules Under the Iowa Amendments, Outlets & Valves

Iowa Journeyperson Plumber Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Iowa Licensing, Exam Format, Code Adoption & UPC General Regulations

1.1 Iowa Licensing Tiers, PMSB Rules, Code Adoption, Permits & Inspections 1.2 UPC Chapter 3 General Regulations: Trenching, Protection of Piping & Iowa Burial Depths 1.3 Plumbing Mathematics, Pipe Sizing Formulas & Blueprint Reading 1.4 Hangers, Supports, Pipe Joints, and Material Compatibility 1.5 Exam Format, Approved References & Open-Book Lookup Strategy

2 Chapter 2: Plumbing Fixtures & Fixture Fittings (UPC Chapter 4)

2.1 Fixture Unit Values & Iowa Minimum Plumbing Fixture Requirements 2.2 Water Closets, Urinals, Bidets & Lavatories 2.3 Bathtubs, Showers, Sinks & Food Prep Fixtures 2.4 Plumbing Fixture Installation Standards & ADA Accessibility 2.5 Specialty Appliances, Floor Drains, Indirect Waste & Interceptors

3 Chapter 3: Sanitary Drainage & Building Sewers (UPC Chapter 7)

3.1 Sanitary Drainage System Components, Layout & Gravity Flow Principles 3.2 Drainage Fixture Unit (DFU) Values & Horizontal/Vertical Sizing 3.3 Building Sewers, Building Drains & Sewer Connection Standards 3.4 Drain Slopes, Velocities & Changes of Direction (UPC 706.0 and 708.0) 3.5 Cleanouts: Placement, Sizing, Clearances & Access Requirements 3.6 Sump Pumps, Sewage Ejectors & Backwater Valves 3.7 Drainage Materials, Joints, Prohibited Practices & DWV Testing 3.8 Sizing a Complete DWV System: Two Worked Walkthroughs

4 Chapter 4: Venting Systems (UPC Chapter 9)

4.1 Venting Fundamentals, Trap Seal Protection & the Iowa Trap Arm Table 4.2 Vent Sizing from UPC Table 703.2, Vent Stacks & Yoke Vents 4.3 Wet Venting Under UPC Section 908 and the Iowa Sizing Amendment 4.4 Venting Fixture Batteries: Common Vents, Relief Vents & Why Circuit Venting Is Not an Iowa Method 4.5 Air Admittance Valves, Combination Waste & Vent, and Island Venting 4.6 Vent Termination, Roof Penetrations & Flashings 4.7 Applying the Vent Rules: Worked Venting Walkthroughs 4.8 Diagnosing Venting Failures: Symptom-to-Cause Troubleshooting

5 Chapter 5: Traps, Interceptors & Indirect Waste (UPC Chapters 8 and 10)

5.1 Trap Design, Seals, Prohibited Traps & Trap Primers 5.2 Indirect & Special Waste Receptors and Air Gaps 5.3 Grease Interceptors & Trap Sizing (Hydromechanical & Gravity) 5.4 Oil, Sand, Flammable Liquid & Chemical Interceptors

6 Chapter 6: Water Supply & Distribution (UPC Chapter 6)

6.1 Water Service Piping, Main Sizing & Meter Installation 6.2 Water Supply Fixture Units (WSFU) & Pipe Sizing Calculations 6.3 Water Pressure Regulators, Pressure Relief & Thermal Expansion 6.4 Backflow Prevention: Cross-Connection Control & Device Selection 6.5 Potable Water Pipe Materials, Valves & Disinfection

7 Chapter 7: Water Heaters (UPC Chapter 5)

7.1 Water Heater Types, Sizing, Recovery Rate & First-Hour Rating 7.2 Water Heater Safety: T&P Relief Valves, Drain Pans, Combustion Air & Anti-Scald Controls 7.3 Water Heater Venting: Appliance Categories, Vent Connectors, Chimneys & Terminations 7.4 Water Heater Location, Clearances, Supports, Replacement & Iowa Amendments

8 Chapter 8: Storm Drainage (UPC Chapter 11)

8.1 Storm Drainage Scope, Materials, Traps & Prohibited Connections 8.2 Sizing Roof Drains, Leaders & Vertical Rainwater Piping (UPC Table 1103.1) 8.3 Sizing Horizontal Storm Drains, Storm Sewers & Gutters (UPC Tables 1103.2 and 1103.3) 8.4 Side Walls Draining Onto a Roof, Secondary Roof Drainage & Controlled-Flow Roofs 8.5 Subsoil Drains, Areaway Drains, Storm Sumps & Building Storm Sewers

9 Chapter 9: Fuel Gas Piping & Appliance Venting (UPC Chapter 12)

7.1 Iowa Fuel Gas Authority (UPC Chapter 12), Gas Properties, System Types & Regulators 7.2 Gas Pipe Sizing Calculations, Longest Length & Branch Method 7.3 Gas Pipe Materials, Joining, CSST Rules Under the Iowa Amendments, Outlets & Valves 7.4 Fuel Gas Appliance Installation, Clearances & Combustion Air 7.5 Fuel Gas Venting Systems, Chimneys & Safety Testing

7.3 Gas Pipe Materials, Joining, CSST Rules Under the Iowa Amendments, Outlets & Valves

Key Takeaways Explain This Topic AI

Iowa permits only CSST with an arc-resistant jacket or covering system listed to ANSI LC-1 (Optional Section 5.16)/CSA 6.26-2016.

Iowa prohibits CSST for through-wall penetrations from the point of delivery of the gas supply to the inside of the structure.

Iowa deletes UPC Section 1211.3, Arc-Resistant Jacketed CSST, so the electrical bonding requirements of Section 1211.2 apply to CSST installations.

CSST may not be installed where subject to physical damage unless protected in an approved manner.

Sediment traps and appliance shutoff valves are installed as required by UPC Chapter 12 so debris cannot reach appliance gas controls.

Last updated: August 2026

7.3 Gas Pipe Materials, Joining Methods, Outlets & Valves

Fuel gas distribution systems require durable materials, leak-tight joinery, physical nail strike protection, and approved shutoff valves. Because fuel gas leaks inside enclosed building cavities present severe fire and explosion risks, plumbing codes strictly regulate approved piping materials and installation details.

1. Approved Fuel Gas Piping & Tubing Materials

Piping Material Applicable Standard Approved Applications Code Restrictions & Mandates

Black Steel Pipe ASTM A53 / A106 Schedule 40 Indoor structural gas mains, branch lines, risers Standard material for interior fuel gas. Threaded or welded fittings. Must be painted exposed outdoors.

Galvanized Steel Pipe ASTM A53 Schedule 40 Outdoor gas runs, indoor piping Permitted by IFGC and UPC. Zinc coating protects against corrosion.

Corrugated Stainless Steel Tubing (CSST) ANSI LC 1 / CSA 6.26 Interior gas distribution manifolds & branches Requires listed manufacturer fittings. Yellow CSST mandates 6 AWG electrical bonding. Black CSST reduces bonding requirements.

Copper Tubing ASTM B88 Type K or L / ASTM B280 ACR Interior gas piping (where permitted) Prohibited if gas contains > 0.3 grains >0.3 \text{ grains} > 0.3 grains hydrogen sulfide per 100 cu ft 100 \text{ cu ft} 100 cu ft of gas ( 0.7 mg/100 L 0.7 \text{ mg/100 L} 0.7 mg/100 L ). Copper reacts with H 2 S H_2S H 2 ​ S to form flaking copper sulfide.

Polyethylene (PE) Plastic Pipe ASTM D2513 (PE 2708 / PE 4710) Outdoor underground gas mains ONLY STRICTLY PROHIBITED indoors or above ground . Must be buried at least 18 inches 18 \text{ inches} 18 inches deep with a yellow 18 AWG 18 \text{ AWG} 18 AWG tracer wire.

Polyethylene (PE) Underground Rules

Underground Location Only : PE plastic pipe is approved exclusively for exterior, underground burials. It must never pass through or beneath a building foundation unless encased in an airtight metallic conduit vented to the outdoors.

Tracer Wire Mandate : An insulated yellow copper tracer wire of minimum 18 AWG must be buried alongside plastic pipe to facilitate surface electronic pipe locating. One end must terminate above grade at the gas riser.

Riser Transition : PE pipe must transition to metallic pipe prior to emerging above ground using a listed, factory-assembled anodeless riser .

2. CSST Arc-Resistant Jacketing & Electrical Bonding Rules

Corrugated Stainless Steel Tubing (CSST) features thin wall stainless steel tubing (typically 0.010 to 0.012 inches thick). If a building experiences a nearby indirect lightning strike, high-voltage electrical arcing can jump between structural ground paths and unbonded CSST, punching microscopic melt holes through the tubing wall and causing gas fires. [ Electrical Panel / GES ] <=== (Min 6 AWG Copper Bonding Wire) ===> [ CSST Brass Fitting / Manifold ]

Standard Yellow CSST Bonding Rules (ANSI LC 1)

Bonding Jumper Conductor : Yellow CSST must be electrically bonded to the building Electrical Grounding Electrode System (GES) using a solid or stranded copper conductor of minimum 6 AWG .

Attachment Clamp : The bonding clamp must be listed to UL 467 and attached directly to a brass CSST fitting, rigid pipe nipple, or distribution manifold (never directly on the flexible stainless tubing wall).

Maximum Wire Distance : The bonding jumper length must be kept as short as practical, typically not exceeding 75 feet of developed wire length.

Black Arc-Resistant CSST (ANSI LC 1027 / E-Jacket)

Warning

Iowa rewrote the CSST rules — do not answer this from a national prep book. Rule 481—425.4(9)"c" deletes UPC Subsection 1208.5.3.5 and substitutes: only CSST with an arc-resistant jacket or covering system listed in accordance with ANSI LC-1 (Optional Section 5.16)/CSA 6.26-2016 shall be installed , in accordance with the terms of its approval, the conditions of listing, the manufacturer's instructions and the code, including the electrical bonding requirements in Section 1211.2 . The same amendment adds that CSST shall not be used for through-wall penetrations from the point of delivery of the gas supply to the inside of the structure , and shall not be installed where subject to physical damage unless protected in an approved manner.

Rule 481—425.4(9)"d" then deletes Section 1211.3, Arc-Resistant Jacketed CSST . That deletion is the point most candidates miss: in jurisdictions that keep Section 1211.3, an arc-resistant jacketed product can be relieved of the additional direct bonding requirement. Iowa removed that section , so the bonding requirements of Section 1211.2 apply. Treat "black jacketed CSST does not need to be bonded in Iowa" as a false statement.

Striker Plate Physical Protection (Nail Guards)

Where concealed gas piping or tubing passes through structural wood studs, joists, rafters, or wall plates within 1.5 inches of the framing member edge, it must be protected against puncture by drywall screws or nails:

Protection Material : Striker plates made of minimum 16-gauge hardened steel .

Coverage : Striker plates must cover the area of the pipe penetration and extend at least 4 inches above and below bottom plates and top plates.

3. Pipe Joining Technologies & Thread Standards

Threaded NPT Joints : Tapered pipe threads must comply with ANSI/ASME B1.20.1 ( National Pipe Thread ). Thread joint compound (pipe dope) or yellow PTFE tape listed for fuel gas must be applied ONLY TO MALE THREADS . Applying pipe dope to female threads forces compound into the gas stream, clogging appliance orifices and gas valves.

Welded & Flanged Joints : Pipe joints in sizes 2.5 inches and larger , or systems operating at pressures exceeding 5 psi , must be welded by a certified pipe welder.

CSST Fitting Assembly : CSST fittings utilize proprietary metal-to-metal flare or split-ring compression designs. Fittings must never be interchanged between different CSST manufacturers .

PE Plastic Joining : PE pipe must be joined by butt fusion, socket fusion, electrofusion, or listed mechanical transition fittings. Solvent cement and threading are strictly prohibited on PE pipe.

  • 4. Appliance Shutoff Valves, Flexible Connectors & Sediment Traps [ Rigid Gas Supply Pipe ]
  • |
  • [ Full-Port Gas Shutoff Valve ] (Within 6 ft, same room)
  • |
  • [ Flexible Appliance Connector ] (ANSI Z21.24)
  • |
  • +--+--+ <--- Tee Fitting
  • | |---> To Appliance Gas Valve
  • [ Sediment Trap / Drip Leg ] (Min 3" Vertical Capped Nipple)
  • Appliance Shutoff Valves (ANSI Z21.15 / ASME B16.44)

Location : Every gas appliance must have an individual shutoff valve installed within 6 feet of the appliance, in the same room , and upstream of any flexible connector.

Accessibility : Shutoff valves must be readily accessible without requiring tools, panel removal, or structural dismantling.

Flexible Appliance Connectors (ANSI Z21.24 / ANSI Z21.75)

Length Limits : Flexible metallic appliance connectors must not exceed 3 feet in total length (except domestic gas ranges and clothes dryers, which may use connectors up to 6 feet long).

Prohibited Penetrations : Flexible connectors must never pass through walls, floors, ceilings, partitions, or appliance housing cabinets.

Sediment Traps (Drip Legs)

Where dirt, scale, or water vapor enters appliance gas controls, it damages internal solenoid seats. IFGC Section 408 and UPC Section 1211 mandate sediment traps:

Configuration : Constructed using a tee fitting with a vertical bottom outlet containing a capped pipe nipple at least 3 inches long . Gas must enter the tee and execute a 90-degree directional turn, forcing scale and moisture drops to fall into the capped vertical nipple.

Location : Installed downstream of the appliance shutoff valve as close to the appliance inlet as practical.

Exemptions : Sediment traps are NOT required on gas ranges, clothes dryers, outdoor grills, illuminating appliances, or decorative log lighters.