Study guide
3.4 Drain Slopes, Velocities & Changes of Direction (UPC 706.0 and 708.0)
Iowa Journeyperson Plumber Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Iowa Licensing, Exam Format, Code Adoption & UPC General Regulations
1.1 Iowa Licensing Tiers, PMSB Rules, Code Adoption, Permits & Inspections 1.2 UPC Chapter 3 General Regulations: Trenching, Protection of Piping & Iowa Burial Depths 1.3 Plumbing Mathematics, Pipe Sizing Formulas & Blueprint Reading 1.4 Hangers, Supports, Pipe Joints, and Material Compatibility 1.5 Exam Format, Approved References & Open-Book Lookup Strategy
2 Chapter 2: Plumbing Fixtures & Fixture Fittings (UPC Chapter 4)
2.1 Fixture Unit Values & Iowa Minimum Plumbing Fixture Requirements 2.2 Water Closets, Urinals, Bidets & Lavatories 2.3 Bathtubs, Showers, Sinks & Food Prep Fixtures 2.4 Plumbing Fixture Installation Standards & ADA Accessibility 2.5 Specialty Appliances, Floor Drains, Indirect Waste & Interceptors
3 Chapter 3: Sanitary Drainage & Building Sewers (UPC Chapter 7)
3.1 Sanitary Drainage System Components, Layout & Gravity Flow Principles 3.2 Drainage Fixture Unit (DFU) Values & Horizontal/Vertical Sizing 3.3 Building Sewers, Building Drains & Sewer Connection Standards 3.4 Drain Slopes, Velocities & Changes of Direction (UPC 706.0 and 708.0) 3.5 Cleanouts: Placement, Sizing, Clearances & Access Requirements 3.6 Sump Pumps, Sewage Ejectors & Backwater Valves 3.7 Drainage Materials, Joints, Prohibited Practices & DWV Testing 3.8 Sizing a Complete DWV System: Two Worked Walkthroughs
4 Chapter 4: Venting Systems (UPC Chapter 9)
4.1 Venting Fundamentals, Trap Seal Protection & the Iowa Trap Arm Table 4.2 Vent Sizing from UPC Table 703.2, Vent Stacks & Yoke Vents 4.3 Wet Venting Under UPC Section 908 and the Iowa Sizing Amendment 4.4 Venting Fixture Batteries: Common Vents, Relief Vents & Why Circuit Venting Is Not an Iowa Method 4.5 Air Admittance Valves, Combination Waste & Vent, and Island Venting 4.6 Vent Termination, Roof Penetrations & Flashings 4.7 Applying the Vent Rules: Worked Venting Walkthroughs 4.8 Diagnosing Venting Failures: Symptom-to-Cause Troubleshooting
5 Chapter 5: Traps, Interceptors & Indirect Waste (UPC Chapters 8 and 10)
5.1 Trap Design, Seals, Prohibited Traps & Trap Primers 5.2 Indirect & Special Waste Receptors and Air Gaps 5.3 Grease Interceptors & Trap Sizing (Hydromechanical & Gravity) 5.4 Oil, Sand, Flammable Liquid & Chemical Interceptors
6 Chapter 6: Water Supply & Distribution (UPC Chapter 6)
6.1 Water Service Piping, Main Sizing & Meter Installation 6.2 Water Supply Fixture Units (WSFU) & Pipe Sizing Calculations 6.3 Water Pressure Regulators, Pressure Relief & Thermal Expansion 6.4 Backflow Prevention: Cross-Connection Control & Device Selection 6.5 Potable Water Pipe Materials, Valves & Disinfection
7 Chapter 7: Water Heaters (UPC Chapter 5)
7.1 Water Heater Types, Sizing, Recovery Rate & First-Hour Rating 7.2 Water Heater Safety: T&P Relief Valves, Drain Pans, Combustion Air & Anti-Scald Controls 7.3 Water Heater Venting: Appliance Categories, Vent Connectors, Chimneys & Terminations 7.4 Water Heater Location, Clearances, Supports, Replacement & Iowa Amendments
8 Chapter 8: Storm Drainage (UPC Chapter 11)
8.1 Storm Drainage Scope, Materials, Traps & Prohibited Connections 8.2 Sizing Roof Drains, Leaders & Vertical Rainwater Piping (UPC Table 1103.1) 8.3 Sizing Horizontal Storm Drains, Storm Sewers & Gutters (UPC Tables 1103.2 and 1103.3) 8.4 Side Walls Draining Onto a Roof, Secondary Roof Drainage & Controlled-Flow Roofs 8.5 Subsoil Drains, Areaway Drains, Storm Sumps & Building Storm Sewers
9 Chapter 9: Fuel Gas Piping & Appliance Venting (UPC Chapter 12)
7.1 Iowa Fuel Gas Authority (UPC Chapter 12), Gas Properties, System Types & Regulators 7.2 Gas Pipe Sizing Calculations, Longest Length & Branch Method 7.3 Gas Pipe Materials, Joining, CSST Rules Under the Iowa Amendments, Outlets & Valves 7.4 Fuel Gas Appliance Installation, Clearances & Combustion Air 7.5 Fuel Gas Venting Systems, Chimneys & Safety Testing
3.4 Drain Slopes, Velocities & Changes of Direction (UPC 706.0 and 708.0)
Key Takeaways Explain This Topic AI
UPC Section 708.1 requires horizontal drainage piping to run at a uniform slope of not less than 1/4 inch per foot, or 2 percent.
The only slope exception is for piping 4 inches or larger, which may run at not less than 1/8 inch per foot where the AHJ approves it first.
Horizontal-to-horizontal changes of direction use 45-degree wye branches, combination wye and one-eighth bend branches, or fittings of equivalent sweep — never a sanitary tee.
Sanitary tees and sanitary tapped tees are permitted only where a horizontal line enters a vertical stack.
UPC Section 706.2 permits a double sanitary tee only where the barrel of the fitting is not less than two pipe sizes larger than the largest inlet.
Last updated: August 2026
- Drain Pipe Slopes, Velocities & Change of Direction Fittings
- Minimum Drain Pipe Slopes (UPC Section 708.0)
The UPC states this in one sentence, and it is worth memorizing because it is shorter than the table most candidates try to reconstruct from an IPC habit. UPC Section 708.1 : horizontal drainage piping is run in practical alignment at a uniform slope of not less than 1/4 inch per foot (20.8 mm/m), or 2 percent , toward the point of disposal.
- The single exception
- Where it is impractical to obtain 1/4 inch per foot because of
- the depth of the street sewer,
- the structural features of the building, or
- the arrangement of the building or structure,
then piping 4 inches (100 mm) or larger in diameter may be run at a slope of not less than 1/8 inch per foot (1 percent) — and only where first approved by the Authority Having Jurisdiction .
Nominal pipe size Required slope 1/8 inch per foot permitted?
- 1-1/4 inch through 3 inch 1/4 inch per foot (2%) No
- 4 inch and larger 1/4 inch per foot (2%) Yes , with prior AHJ approval, where 1/4 inch per foot is impractical
Warning
Three IPC habits to unlearn. (1) There is no 1/16 inch per foot row in the UPC — that is IPC Table 704.1 for 8-inch and larger pipe. (2) The 1/8 inch per foot exception begins at 4 inches, not 3 inches . (3) UPC Table 703.2 does not reduce fixture-unit capacity when you reduce slope; a 4-inch horizontal drain carries 216 DFU at either slope. Capacity-versus-slope tables are an IPC feature.
Manning's Equation & Velocity Dynamics
The velocity of liquid flowing under gravity in a partially full pipe is calculated using Manning's Equation : V = 1.486 n × R 2 / 3 × S 1 / 2 V = \frac{1.486}{n} \times R^{2/3} \times S^{1/2} V = n 1.486 × R 2/3 × S 1/2
Where:
V = V = V = Velocity of flow (feet per second)
n = n = n = Manning's roughness coefficient (typically 0.009 0.009 0.009 to 0.011 0.011 0.011 for smooth PVC/ABS plastic; 0.012 0.012 0.012 to 0.015 0.015 0.015 for cast iron)
- R = R = R = Hydraulic radius ( A / P A / P A / P , cross-sectional area divided by wetted perimeter)
- S = S = S = Slope of energy grade line (feet fall per foot of pipe length)
- Consequences of Improper Pitch
Insufficient slope (below 1/4 inch per foot where the exception does not apply): Velocity drops below about 2.0 fps. Heavy organic solids settle out, grease cools and coats pipe walls, and chronic blockages form.
Excessive Slope ( > 1 / 2 " per ft > 1/2" \text{ per ft} > 1/2" per ft on long runs): Liquid velocity exceeds 10.0 fps. The liquid accelerates past solids, leaving dry paper and fecal deposits stranded in the pipe, while creating severe hydraulic impact forces at fittings.
Change of Direction Fitting Rules (UPC Section 706.0)
Because moving wastewater possesses kinetic momentum, improper fitting selection creates turbulence, hydraulic jumps, and drain blockages. The UPC strictly dictates which fittings are allowed based on the directional orientation of flow.
The UPC splits this into four short subsections. Read them as a set:
706.1 Approved fittings. Changes of direction are made with approved fittings of the angles presented by a one-sixteenth bend, one-eighth bend, or one-sixth bend , or other approved fittings of equivalent sweep.
706.2 Horizontal to vertical. Horizontal drainage lines entering a vertical stack enter through 45-degree wye branches, 60-degree wye branches, combination wye and one-eighth bend branches, sanitary tee or sanitary tapped tee branches , or other approved fittings of equivalent sweep. This is the only orientation where a sanitary tee is permitted.
706.3 Horizontal to horizontal. Horizontal lines connecting to other horizontal lines enter through 45-degree wye branches, combination wye and one-eighth bend branches , or other approved fittings of equivalent sweep.
706.4 Vertical to horizontal. Vertical lines connecting to horizontal lines enter through 45-degree wye branches, combination wye and one-eighth bend branches , or equivalent sweep. Branches or offsets of 60 degrees are permitted where installed in a true vertical position.
Directional change UPC-listed fittings Not acceptable
Horizontal to vertical (706.2) 45° wye, 60° wye, combination wye and 1/8 bend, sanitary tee, sanitary tapped tee Fittings that direct flow upward against the drop
Horizontal to horizontal (706.3) 45° wye, combination wye and 1/8 bend, equivalent sweep Sanitary tee , short-radius quarter bend
Vertical to horizontal (706.4) 45° wye, combination wye and 1/8 bend, equivalent sweep; 60° branch or offset in a true vertical position Sanitary tee , short-radius quarter bend
A long-sweep quarter bend is normally accepted as a fitting "of equivalent sweep," but notice the code does not name it — it names the wye family. When an exam option lists a fitting the code names verbatim, take it.
Back-to-Back Fixture Connections & Double Fitting Restrictions
When two fixtures are installed back-to-back on opposite sides of a partition wall, their trap arms must enter the vertical drain stack through an approved fitting that prevents cross-discharge.
The Water Closet Cross-Flow Problem
UPC Section 706.2 states the governing principle: no fitting having more than one inlet at the same level shall be used unless such fitting is constructed so that the discharge from one inlet cannot readily enter any other inlet. Flushing one water closet into an undersized double fitting drives a jet of water straight across the barrel into the opposing arm, which produces:
Siphonage or blowout of the opposing water closet trap seal.
Waste backing up into the bowl of the adjacent fixture. PROHIBITED: STANDARD DOUBLE SANITARY TEE FOR BACK-TO-BACK WATER CLOSETS
- WC #1 ───► [ Standard Double Tee ] ◄─── WC #2
- │ (Cross-Flow Hazard!)
- ▼
- REQUIRED: DOUBLE FIXTURE TEE WITH DIRECTIONAL BAFFLE OR DOUBLE WYE
- WC #1 ───► [ Double Fixture Tee ] ◄─── WC #2
- (Internal Baffle Directs
- Flow Downward)
- │
- ▼
Code Requirement (UPC 706.2): Double sanitary tees are not banned outright in the UPC. They are permitted where the barrel of the fitting is not less than two pipe sizes larger than the largest inlet . The pipe sizes recognized for this purpose are 2, 2-1/2, 3, 3-1/2, 4, 4-1/2, 5, 6 inches and so on — so a double sanitary tee with 3-inch inlets requires a 4-inch barrel (3 → 3-1/2 → 4). Below that, use a double combination wye and one-eighth bend or a double wye, whose internal sweeps carry each discharge downward instead of across.
Important
Count the half sizes. "Two pipe sizes larger" in UPC 706.2 uses the code's own recognized series, which includes 2-1/2, 3-1/2 and 4-1/2 inches. Candidates who count 3 → 4 → 5 arrive at a 5-inch barrel and pick the wrong answer.