Study guide
7.2 Water Heater Safety: T&P Relief Valves, Drain Pans, Combustion Air & Anti-Scald Controls
Iowa Journeyperson Plumber Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Iowa Licensing, Exam Format, Code Adoption & UPC General Regulations
1.1 Iowa Licensing Tiers, PMSB Rules, Code Adoption, Permits & Inspections 1.2 UPC Chapter 3 General Regulations: Trenching, Protection of Piping & Iowa Burial Depths 1.3 Plumbing Mathematics, Pipe Sizing Formulas & Blueprint Reading 1.4 Hangers, Supports, Pipe Joints, and Material Compatibility 1.5 Exam Format, Approved References & Open-Book Lookup Strategy
2 Chapter 2: Plumbing Fixtures & Fixture Fittings (UPC Chapter 4)
2.1 Fixture Unit Values & Iowa Minimum Plumbing Fixture Requirements 2.2 Water Closets, Urinals, Bidets & Lavatories 2.3 Bathtubs, Showers, Sinks & Food Prep Fixtures 2.4 Plumbing Fixture Installation Standards & ADA Accessibility 2.5 Specialty Appliances, Floor Drains, Indirect Waste & Interceptors
3 Chapter 3: Sanitary Drainage & Building Sewers (UPC Chapter 7)
3.1 Sanitary Drainage System Components, Layout & Gravity Flow Principles 3.2 Drainage Fixture Unit (DFU) Values & Horizontal/Vertical Sizing 3.3 Building Sewers, Building Drains & Sewer Connection Standards 3.4 Drain Slopes, Velocities & Changes of Direction (UPC 706.0 and 708.0) 3.5 Cleanouts: Placement, Sizing, Clearances & Access Requirements 3.6 Sump Pumps, Sewage Ejectors & Backwater Valves 3.7 Drainage Materials, Joints, Prohibited Practices & DWV Testing 3.8 Sizing a Complete DWV System: Two Worked Walkthroughs
4 Chapter 4: Venting Systems (UPC Chapter 9)
4.1 Venting Fundamentals, Trap Seal Protection & the Iowa Trap Arm Table 4.2 Vent Sizing from UPC Table 703.2, Vent Stacks & Yoke Vents 4.3 Wet Venting Under UPC Section 908 and the Iowa Sizing Amendment 4.4 Venting Fixture Batteries: Common Vents, Relief Vents & Why Circuit Venting Is Not an Iowa Method 4.5 Air Admittance Valves, Combination Waste & Vent, and Island Venting 4.6 Vent Termination, Roof Penetrations & Flashings 4.7 Applying the Vent Rules: Worked Venting Walkthroughs 4.8 Diagnosing Venting Failures: Symptom-to-Cause Troubleshooting
5 Chapter 5: Traps, Interceptors & Indirect Waste (UPC Chapters 8 and 10)
5.1 Trap Design, Seals, Prohibited Traps & Trap Primers 5.2 Indirect & Special Waste Receptors and Air Gaps 5.3 Grease Interceptors & Trap Sizing (Hydromechanical & Gravity) 5.4 Oil, Sand, Flammable Liquid & Chemical Interceptors
6 Chapter 6: Water Supply & Distribution (UPC Chapter 6)
6.1 Water Service Piping, Main Sizing & Meter Installation 6.2 Water Supply Fixture Units (WSFU) & Pipe Sizing Calculations 6.3 Water Pressure Regulators, Pressure Relief & Thermal Expansion 6.4 Backflow Prevention: Cross-Connection Control & Device Selection 6.5 Potable Water Pipe Materials, Valves & Disinfection
7 Chapter 7: Water Heaters (UPC Chapter 5)
7.1 Water Heater Types, Sizing, Recovery Rate & First-Hour Rating 7.2 Water Heater Safety: T&P Relief Valves, Drain Pans, Combustion Air & Anti-Scald Controls 7.3 Water Heater Venting: Appliance Categories, Vent Connectors, Chimneys & Terminations 7.4 Water Heater Location, Clearances, Supports, Replacement & Iowa Amendments
8 Chapter 8: Storm Drainage (UPC Chapter 11)
8.1 Storm Drainage Scope, Materials, Traps & Prohibited Connections 8.2 Sizing Roof Drains, Leaders & Vertical Rainwater Piping (UPC Table 1103.1) 8.3 Sizing Horizontal Storm Drains, Storm Sewers & Gutters (UPC Tables 1103.2 and 1103.3) 8.4 Side Walls Draining Onto a Roof, Secondary Roof Drainage & Controlled-Flow Roofs 8.5 Subsoil Drains, Areaway Drains, Storm Sumps & Building Storm Sewers
9 Chapter 9: Fuel Gas Piping & Appliance Venting (UPC Chapter 12)
7.1 Iowa Fuel Gas Authority (UPC Chapter 12), Gas Properties, System Types & Regulators 7.2 Gas Pipe Sizing Calculations, Longest Length & Branch Method 7.3 Gas Pipe Materials, Joining, CSST Rules Under the Iowa Amendments, Outlets & Valves 7.4 Fuel Gas Appliance Installation, Clearances & Combustion Air 7.5 Fuel Gas Venting Systems, Chimneys & Safety Testing
7.2 Water Heater Safety: T&P Relief Valves, Drain Pans, Combustion Air & Anti-Scald Controls
Key Takeaways Explain This Topic AI
Temperature and Pressure (T&P) relief valves must be ASME listed and rated to open at 150 psi pressure or 210°F temperature, with the sensing element located in the top 6 inches of the water heater tank.
T&P relief valve discharge piping must be full size, constructed of rigid approved hard pipe, slope continuously downward without traps or sags, and terminate between 6 inches and 24 inches above the floor or waste receptor.
Water heater drain pans are mandatory whenever leakage would cause structural damage, requiring a minimum depth of 1.5 inches and a 3/4-inch independent drain line.
Indoor combustion air requirements for atmospheric fuel-fired water heaters mandate a minimum room volume of 50 cubic feet per 1,000 BTU/hr total input rating of all appliances in the space.
Thermostatic mixing valves complying with ASSE 1070 must be installed to limit hot water delivered to public lavatories to a maximum temperature of 120°F.
Last updated: August 2026
7.2 Water Heater Safety: T&P Relief Valves, Drain Pans, Combustion Air & Anti-Scald Controls
Water heaters combine hydraulic pressure, electrical energy, and high thermal combustion into a single storage vessel. Improper installation can result in catastrophic thermal explosions, dangerous carbon monoxide poisoning, scalding injuries, or major building flooding. The Uniform Plumbing Code (UPC) Chapter 5 and Chapter 6 govern water heater design, safety relief valves, drain pan protection, combustion air supply, and anti-scald mixing valves.
1. Where this section sits
Section 7.1 covered selection and sizing — recovery rate, first-hour rating, tankless flow at a temperature rise, and mixed-water arithmetic. This section covers the four things that keep a correctly sized heater from hurting anyone: the temperature and pressure relief valve and its discharge piping, the drain pan , combustion air , and anti-scald controls . Section 7.3 covers venting, and Section 7.4 covers location, clearances, and the Iowa amendments.
2. Temperature & Pressure (T&P) Relief Valve Requirements
Every water heater storage vessel MUST be equipped with an approved, combination Temperature and Pressure (T&P) relief valve listed to ASME A112.4.1 / CSA 4.4 .
Pressure Activation : Set to snap open at 150 psi (1,034 kPa) .
Temperature Activation : Set to open at 210°F (99°C) . (Water under 150 psi pressure remains liquid at 210°F, but if the tank ruptures, superheated water instantly flashes into explosive steam, expanding 1,600 times in volume).
Probe Placement : The thermal sensing probe must extend into the top 6 inches of the tank, where the hottest water collects.
T&P Relief Valve Discharge Piping Rules (UPC Section 608.5)
To prevent steam burns or secondary water damage during relief discharge, the discharge pipe must strictly adhere to the following code mandates:
Approved Rigid Materials : Must be hard-drawn copper, CPVC, galvanized steel, or threaded brass. Flexible plastic tubing, PEX (unless specifically listed for T&P discharge), vinyl hose, or soldered soft copper are prohibited.
Full Nominal Diameter : Pipe size must equal the valve outlet size (typically 3/4 inch minimum). No reduction in pipe diameter or inline restriction is allowed.
Continuous Gravity Slope : Pipe must slope continuously downward toward the discharge point. No upward loops, sags, traps, or horizontal dips where water can collect.
No Valves or Threads at Terminal : Must contain NO shutoff valves, check valves, or threaded fittings at the discharge end (to prevent caps or plugs from being installed).
Terminal Clearance : Must terminate into an approved floor drain, indirect waste receptor, or water heater pan, with the end of the pipe pointing downward and terminating between 6 inches and 24 inches above the floor or flood level rim. [ T&P Valve (Top 6" of Tank) ] ---> [ Full 3/4" Hard Pipe ] ---> (Slopes Down) ---> [ Terminates 6" to 24" Above Floor Drain ]
3. Water Heater Drain Pans (UPC Section 507.24)
Where water leakage from a water heater storage tank or connections would cause structural damage to building components (such as installations in attics, upper floor wood-joist structures, or over finished spaces):
Pan Material & Size : A drain pan made of minimum 24-gauge galvanized steel or approved high-impact plastic, at least 1.5 inches (38 mm) deep, must be installed under the heater.
Pan Drain Line : Must be equipped with an independent, full-size 3/4-inch minimum drain line run to an approved floor drain, indirect waste receptor, or exterior ground level.
4. Combustion Air & Venting Standards
Atmospheric gas-fired water heaters require adequate oxygen for complete fuel combustion to prevent carbon monoxide production.
Indoor Space Volume Rule (Standard Method)
Per UPC Section 506.2 , if a gas appliance is installed in an unconfined indoor space, the room must have a volume of at least 50 cubic feet per 1,000 BTU/hr of total aggregate input rating of all fuel-burning appliances in that room.
Example : A 40,000 BTU/hr water heater + a 80,000 BTU/hr furnace = 120,000 BTU/hr total input. Minimum required room volume = 120 × 50 = 6 , 000 cu ft 120 \times 50 = 6,000 \text{ cu ft} 120 × 50 = 6 , 000 cu ft .
Outdoor Air Ducts
If indoor volume is insufficient, two permanent openings (one within 12 inches of the ceiling, one within 12 inches of the floor) communicating with the outdoors must be provided:
Vertical Ducts : 1 square inch free area per 4,000 BTU/hr total input.
Horizontal Ducts : 1 square inch free area per 2,000 BTU/hr total input.
Vent clearances — see Section 7.3
Type B double-wall gas vent and single-wall metal vent connectors have different clearance requirements to combustibles, and the appliance venting categories determine which vent material is even permitted. Both are covered in Section 7.3 , along with vent connector rise, common venting, orphaned water heaters, masonry chimneys, and through-the-wall terminations.
5. Anti-Scald Hot Water Controls
To prevent catastrophic thermal burn injuries (water at 140°F causes third-degree burns in 5 seconds; water at 130°F causes burns in 30 seconds):
Public Handwashing Lavatories : Temperature-limiting devices conforming to ASSE 1070 must limit delivered hot water temperature to a maximum of 120°F (49°C) . Iowa adds to UPC Section 407.3 that "these devices shall be installed at or as close as possible to the point of use" — see Section 7.4 for the full set of Iowa temperature-limiting amendments, including the new Section 408.12 for pet grooming stations.
Residential Showers/Tubs : Pressure-balance or thermostatic shower valves conforming to ASSE 1016 / CSA B125.16 must limit maximum outlet water to 120°F .