Study guide
7.1 Water Heater Types, Sizing, Recovery Rate & First-Hour Rating
Iowa Journeyperson Plumber Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Iowa Licensing, Exam Format, Code Adoption & UPC General Regulations
1.1 Iowa Licensing Tiers, PMSB Rules, Code Adoption, Permits & Inspections 1.2 UPC Chapter 3 General Regulations: Trenching, Protection of Piping & Iowa Burial Depths 1.3 Plumbing Mathematics, Pipe Sizing Formulas & Blueprint Reading 1.4 Hangers, Supports, Pipe Joints, and Material Compatibility 1.5 Exam Format, Approved References & Open-Book Lookup Strategy
2 Chapter 2: Plumbing Fixtures & Fixture Fittings (UPC Chapter 4)
2.1 Fixture Unit Values & Iowa Minimum Plumbing Fixture Requirements 2.2 Water Closets, Urinals, Bidets & Lavatories 2.3 Bathtubs, Showers, Sinks & Food Prep Fixtures 2.4 Plumbing Fixture Installation Standards & ADA Accessibility 2.5 Specialty Appliances, Floor Drains, Indirect Waste & Interceptors
3 Chapter 3: Sanitary Drainage & Building Sewers (UPC Chapter 7)
3.1 Sanitary Drainage System Components, Layout & Gravity Flow Principles 3.2 Drainage Fixture Unit (DFU) Values & Horizontal/Vertical Sizing 3.3 Building Sewers, Building Drains & Sewer Connection Standards 3.4 Drain Slopes, Velocities & Changes of Direction (UPC 706.0 and 708.0) 3.5 Cleanouts: Placement, Sizing, Clearances & Access Requirements 3.6 Sump Pumps, Sewage Ejectors & Backwater Valves 3.7 Drainage Materials, Joints, Prohibited Practices & DWV Testing 3.8 Sizing a Complete DWV System: Two Worked Walkthroughs
4 Chapter 4: Venting Systems (UPC Chapter 9)
4.1 Venting Fundamentals, Trap Seal Protection & the Iowa Trap Arm Table 4.2 Vent Sizing from UPC Table 703.2, Vent Stacks & Yoke Vents 4.3 Wet Venting Under UPC Section 908 and the Iowa Sizing Amendment 4.4 Venting Fixture Batteries: Common Vents, Relief Vents & Why Circuit Venting Is Not an Iowa Method 4.5 Air Admittance Valves, Combination Waste & Vent, and Island Venting 4.6 Vent Termination, Roof Penetrations & Flashings 4.7 Applying the Vent Rules: Worked Venting Walkthroughs 4.8 Diagnosing Venting Failures: Symptom-to-Cause Troubleshooting
5 Chapter 5: Traps, Interceptors & Indirect Waste (UPC Chapters 8 and 10)
5.1 Trap Design, Seals, Prohibited Traps & Trap Primers 5.2 Indirect & Special Waste Receptors and Air Gaps 5.3 Grease Interceptors & Trap Sizing (Hydromechanical & Gravity) 5.4 Oil, Sand, Flammable Liquid & Chemical Interceptors
6 Chapter 6: Water Supply & Distribution (UPC Chapter 6)
6.1 Water Service Piping, Main Sizing & Meter Installation 6.2 Water Supply Fixture Units (WSFU) & Pipe Sizing Calculations 6.3 Water Pressure Regulators, Pressure Relief & Thermal Expansion 6.4 Backflow Prevention: Cross-Connection Control & Device Selection 6.5 Potable Water Pipe Materials, Valves & Disinfection
7 Chapter 7: Water Heaters (UPC Chapter 5)
7.1 Water Heater Types, Sizing, Recovery Rate & First-Hour Rating 7.2 Water Heater Safety: T&P Relief Valves, Drain Pans, Combustion Air & Anti-Scald Controls 7.3 Water Heater Venting: Appliance Categories, Vent Connectors, Chimneys & Terminations 7.4 Water Heater Location, Clearances, Supports, Replacement & Iowa Amendments
8 Chapter 8: Storm Drainage (UPC Chapter 11)
8.1 Storm Drainage Scope, Materials, Traps & Prohibited Connections 8.2 Sizing Roof Drains, Leaders & Vertical Rainwater Piping (UPC Table 1103.1) 8.3 Sizing Horizontal Storm Drains, Storm Sewers & Gutters (UPC Tables 1103.2 and 1103.3) 8.4 Side Walls Draining Onto a Roof, Secondary Roof Drainage & Controlled-Flow Roofs 8.5 Subsoil Drains, Areaway Drains, Storm Sumps & Building Storm Sewers
9 Chapter 9: Fuel Gas Piping & Appliance Venting (UPC Chapter 12)
7.1 Iowa Fuel Gas Authority (UPC Chapter 12), Gas Properties, System Types & Regulators 7.2 Gas Pipe Sizing Calculations, Longest Length & Branch Method 7.3 Gas Pipe Materials, Joining, CSST Rules Under the Iowa Amendments, Outlets & Valves 7.4 Fuel Gas Appliance Installation, Clearances & Combustion Air 7.5 Fuel Gas Venting Systems, Chimneys & Safety Testing
7.1 Water Heater Types, Sizing, Recovery Rate & First-Hour Rating
Key Takeaways Explain This Topic AI
UPC Chapter 5 governs water heaters and carries 8 percent of the Iowa Journeyperson Plumber with Gas examination.
Recovery rate in gallons per hour equals input times efficiency divided by 8.33 pounds per gallon times the temperature rise.
First-hour rating combines usable storage with one hour of recovery, and is the number that should be matched to peak-hour demand.
A 4,500-watt electric element delivers about 20.5 gallons per hour of recovery at a 90-degree temperature rise, which is why electric storage heaters are sized on tank volume rather than on recovery.
Tankless water heaters are selected on flow at a stated temperature rise, so the same unit delivers far less hot water in an Iowa winter than on a summer day.
Last updated: August 2026
- Water Heater Types, Sizing, Recovery Rate & First-Hour Rating
- Why Chapter 5 is worth 8 percent
The Iowa content outline gives Chapter 5 — Water Heaters 8 percent , the same weight as Chapter 4, Fixtures and Fittings, and more than General Regulations, Indirect Wastes, or Traps and Interceptors. That is roughly six questions on a 75-question exam, and they split predictably between sizing arithmetic (this section), safety devices (Section 7.2), venting (Section 7.3), and location and Iowa amendments (Section 7.4).
Water heaters also concentrate more hazard per cubic foot than anything else a plumber installs: a pressure vessel, a fuel-fired burner or a high-current electrical circuit, and stored water hot enough to scald, all in a closet. The code's tone in Chapter 5 reflects that.
1. The four families you will meet
Type How it works Where it fits
Storage (tank) Gas burner or electric elements heat a stored volume, held at a thermostat setpoint The default residential and light-commercial choice; forgiving of short heavy draws
Tankless (instantaneous) Heats water on demand as it flows; no storage Space-constrained installations, high-turnover single-fixture service; sensitive to inlet temperature
Indirect-fired A coil or external heat exchanger driven by a boiler heats a storage tank Buildings that already have a boiler, especially hydronic-heated homes
Heat pump (hybrid) Moves heat from the surrounding air into the tank rather than generating it Efficient where there is conditioned space to draw from and adequate room volume
Two Iowa-specific notes on selection. Incoming water is cold here — main temperatures in the 40s Fahrenheit in late winter are ordinary — which punishes tankless sizing (see below). And a heat-pump water heater takes heat out of the space it sits in, so a unit in a small unconditioned basement room may fight the surrounding air rather than cooperate with it.
2. Recovery rate: the core formula
Recovery rate is how many gallons an hour a heater can raise through a given temperature rise.
Gas-fired: GPH = Input (Btu/h) × Efficiency 8.33 × Δ T \text{GPH} = \frac{\text{Input (Btu/h)} \times \text{Efficiency}}{8.33 \times \Delta T} GPH = 8.33 × Δ T Input (Btu/h) × Efficiency
Electric: GPH = Watts × 3.412 8.33 × Δ T \text{GPH} = \frac{\text{Watts} \times 3.412}{8.33 \times \Delta T} GPH = 8.33 × Δ T Watts × 3.412
The 8.33 is the weight of a gallon of water in pounds, and one Btu raises one pound of water one degree Fahrenheit — so the denominator is simply the Btu needed to lift one gallon through the rise. The 3.412 converts watts to Btu per hour.
Worked example — gas
A 40,000 Btu/h gas water heater at 80 percent thermal efficiency, raising water from 50°F to 140°F (a 90°F rise ): GPH = 40 , 000 × 0.80 8.33 × 90 = 32 , 000 749.7 ≈ 42.7 gallons per hour \text{GPH} = \frac{40,000 \times 0.80}{8.33 \times 90} = \frac{32,000}{749.7} \approx 42.7 \text{ gallons per hour} GPH = 8.33 × 90 40 , 000 × 0.80 = 749.7 32 , 000 ≈ 42.7 gallons per hour
Worked example — electric
A single 4,500-watt element at the same 90°F rise: GPH = 4 , 500 × 3.412 8.33 × 90 = 15 , 354 749.7 ≈ 20.5 gallons per hour \text{GPH} = \frac{4,500 \times 3.412}{8.33 \times 90} = \frac{15,354}{749.7} \approx 20.5 \text{ gallons per hour} GPH = 8.33 × 90 4 , 500 × 3.412 = 749.7 15 , 354 ≈ 20.5 gallons per hour
That contrast is the whole story of electric versus gas storage. A gas heater recovers roughly twice as fast, which is why a 40-gallon gas heater and a 50-gallon electric heater serve similar households. Electric storage capacity is bought in the tank; gas storage capacity is bought in the burner.
3. First-hour rating: the number that actually matters
First-hour rating (FHR) is the gallons of hot water a heater can deliver in one hour starting from a fully heated tank. It combines what is already stored with what the burner or elements can add during that hour: FHR ≈ ( Usable storage ) + ( Recovery in one hour ) \text{FHR} \approx (\text{Usable storage}) + (\text{Recovery in one hour}) FHR ≈ ( Usable storage ) + ( Recovery in one hour )
Usable storage is not the nameplate gallons. As hot water leaves the top of the tank, cold water enters the bottom and mixes; the outlet temperature falls below useful before the tank is empty. A common planning figure is about 70 percent of rated volume.
Worked example
A 40-gallon gas heater with the 42.7 GPH recovery calculated above:
- Usable storage: 40 × 0.70 = 28 gallons
- Recovery in one hour: 42.7 gallons
- FHR ≈ 70.7 gallons
Compare that to a peak-hour demand estimate: two 10-minute showers at 2.0 gpm (40 gallons), a dishwasher (6 gallons), and a load of laundry (20 gallons) is about 66 gallons in the morning peak. The 40-gallon gas heater fits, with little margin. Swap in the 50-gallon electric heater at 20.5 GPH recovery — usable 35 + recovery 20.5 = FHR ≈ 55.5 gallons — and the same household runs out mid-morning.
Important
Size to first-hour rating against peak-hour demand, not to tank gallons against household size. "Two people, 40 gallons" rules of thumb ignore recovery entirely and are the reason so many replacement heaters disappoint the customer.
4. Tankless sizing: flow at a temperature rise
A tankless heater has no storage, so it is rated in gallons per minute at a stated temperature rise . Rearranging the recovery formula for a per-minute basis: GPM = Input (Btu/h) × Efficiency 500 × Δ T \text{GPM} = \frac{\text{Input (Btu/h)} \times \text{Efficiency}}{500 \times \Delta T} GPM = 500 × Δ T Input (Btu/h) × Efficiency
The 500 is 8.33 pounds per gallon × 60 minutes per hour.
Worked example — the Iowa winter problem
A 199,000 Btu/h tankless unit at 0.95 efficiency:
Summer , inlet 65°F, outlet 120°F, rise 55°F : GPM = (199,000 × 0.95) ÷ (500 × 55) = 189,050 ÷ 27,500 ≈ 6.9 gpm — two showers and a sink.
Winter , inlet 42°F, outlet 120°F, rise 78°F : GPM = 189,050 ÷ (500 × 78) = 189,050 ÷ 39,000 ≈ 4.8 gpm — noticeably less.
The unit did not change; the temperature rise did. Any tankless capacity claim that does not state the rise is meaningless, and in Iowa you size on the winter rise.
5. Mixed-water and tempered storage
Commercial installations frequently store hot and deliver tempered, and the mixing arithmetic shows up in sizing questions: V hot = V mixed × T mixed − T cold T hot − T cold V_{\text{hot}} = V_{\text{mixed}} \times \frac{T_{\text{mixed}} - T_{\text{cold}}}{T_{\text{hot}} - T_{\text{cold}}} V hot = V mixed × T hot − T cold T mixed − T cold
Example: deliver 100 gallons at 110°F from 140°F storage with 50°F cold water. V hot = 100 × 110 − 50 140 − 50 = 100 × 60 90 = 66.7 gallons V_{\text{hot}} = 100 \times \frac{110 - 50}{140 - 50} = 100 \times \frac{60}{90} = 66.7 \text{ gallons} V hot = 100 × 140 − 50 110 − 50 = 100 × 90 60 = 66.7 gallons
Storing hotter buys effective capacity — 100 gallons of 140°F storage delivers 150 gallons of 110°F water — which is exactly why commercial systems store hot and temper at the point of use, and exactly why the anti-scald devices in Section 7.2 are not optional.