Study guide
6.4 Backflow Prevention: Cross-Connection Control & Device Selection
Iowa Journeyperson Plumber Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Iowa Licensing, Exam Format, Code Adoption & UPC General Regulations
1.1 Iowa Licensing Tiers, PMSB Rules, Code Adoption, Permits & Inspections 1.2 UPC Chapter 3 General Regulations: Trenching, Protection of Piping & Iowa Burial Depths 1.3 Plumbing Mathematics, Pipe Sizing Formulas & Blueprint Reading 1.4 Hangers, Supports, Pipe Joints, and Material Compatibility 1.5 Exam Format, Approved References & Open-Book Lookup Strategy
2 Chapter 2: Plumbing Fixtures & Fixture Fittings (UPC Chapter 4)
2.1 Fixture Unit Values & Iowa Minimum Plumbing Fixture Requirements 2.2 Water Closets, Urinals, Bidets & Lavatories 2.3 Bathtubs, Showers, Sinks & Food Prep Fixtures 2.4 Plumbing Fixture Installation Standards & ADA Accessibility 2.5 Specialty Appliances, Floor Drains, Indirect Waste & Interceptors
3 Chapter 3: Sanitary Drainage & Building Sewers (UPC Chapter 7)
3.1 Sanitary Drainage System Components, Layout & Gravity Flow Principles 3.2 Drainage Fixture Unit (DFU) Values & Horizontal/Vertical Sizing 3.3 Building Sewers, Building Drains & Sewer Connection Standards 3.4 Drain Slopes, Velocities & Changes of Direction (UPC 706.0 and 708.0) 3.5 Cleanouts: Placement, Sizing, Clearances & Access Requirements 3.6 Sump Pumps, Sewage Ejectors & Backwater Valves 3.7 Drainage Materials, Joints, Prohibited Practices & DWV Testing 3.8 Sizing a Complete DWV System: Two Worked Walkthroughs
4 Chapter 4: Venting Systems (UPC Chapter 9)
4.1 Venting Fundamentals, Trap Seal Protection & the Iowa Trap Arm Table 4.2 Vent Sizing from UPC Table 703.2, Vent Stacks & Yoke Vents 4.3 Wet Venting Under UPC Section 908 and the Iowa Sizing Amendment 4.4 Venting Fixture Batteries: Common Vents, Relief Vents & Why Circuit Venting Is Not an Iowa Method 4.5 Air Admittance Valves, Combination Waste & Vent, and Island Venting 4.6 Vent Termination, Roof Penetrations & Flashings 4.7 Applying the Vent Rules: Worked Venting Walkthroughs 4.8 Diagnosing Venting Failures: Symptom-to-Cause Troubleshooting
5 Chapter 5: Traps, Interceptors & Indirect Waste (UPC Chapters 8 and 10)
5.1 Trap Design, Seals, Prohibited Traps & Trap Primers 5.2 Indirect & Special Waste Receptors and Air Gaps 5.3 Grease Interceptors & Trap Sizing (Hydromechanical & Gravity) 5.4 Oil, Sand, Flammable Liquid & Chemical Interceptors
6 Chapter 6: Water Supply & Distribution (UPC Chapter 6)
6.1 Water Service Piping, Main Sizing & Meter Installation 6.2 Water Supply Fixture Units (WSFU) & Pipe Sizing Calculations 6.3 Water Pressure Regulators, Pressure Relief & Thermal Expansion 6.4 Backflow Prevention: Cross-Connection Control & Device Selection 6.5 Potable Water Pipe Materials, Valves & Disinfection
7 Chapter 7: Water Heaters (UPC Chapter 5)
7.1 Water Heater Types, Sizing, Recovery Rate & First-Hour Rating 7.2 Water Heater Safety: T&P Relief Valves, Drain Pans, Combustion Air & Anti-Scald Controls 7.3 Water Heater Venting: Appliance Categories, Vent Connectors, Chimneys & Terminations 7.4 Water Heater Location, Clearances, Supports, Replacement & Iowa Amendments
8 Chapter 8: Storm Drainage (UPC Chapter 11)
8.1 Storm Drainage Scope, Materials, Traps & Prohibited Connections 8.2 Sizing Roof Drains, Leaders & Vertical Rainwater Piping (UPC Table 1103.1) 8.3 Sizing Horizontal Storm Drains, Storm Sewers & Gutters (UPC Tables 1103.2 and 1103.3) 8.4 Side Walls Draining Onto a Roof, Secondary Roof Drainage & Controlled-Flow Roofs 8.5 Subsoil Drains, Areaway Drains, Storm Sumps & Building Storm Sewers
9 Chapter 9: Fuel Gas Piping & Appliance Venting (UPC Chapter 12)
7.1 Iowa Fuel Gas Authority (UPC Chapter 12), Gas Properties, System Types & Regulators 7.2 Gas Pipe Sizing Calculations, Longest Length & Branch Method 7.3 Gas Pipe Materials, Joining, CSST Rules Under the Iowa Amendments, Outlets & Valves 7.4 Fuel Gas Appliance Installation, Clearances & Combustion Air 7.5 Fuel Gas Venting Systems, Chimneys & Safety Testing
6.4 Backflow Prevention: Cross-Connection Control & Device Selection
Key Takeaways Explain This Topic AI
A cross-connection is any actual or potential physical link between a potable water system and any non-potable liquid, gas, solid, or waste substance.
Backsiphonage is caused by negative or sub-atmospheric pressure in the water supply piping, while backpressure occurs when downstream pressure exceeds supply pressure.
A Reduced Pressure Principle Backflow Preventer (RPBP / RP - ASSE 1013) offers the highest mechanical protection for high-hazard cross-connections subject to backpressure or backsiphonage.
Pressure Vacuum Breaker Assemblies (PVB - ASSE 1020) protect high or low hazards under backsiphonage conditions only and must be installed at least 12 inches above all downstream piping.
Atmospheric Vacuum Breakers (AVB - ASSE 1001) cannot be subjected to continuous pressure for more than 12 hours in any 24-hour period and cannot have shutoff valves installed downstream.
Last updated: August 2026
6.4 Backflow Prevention: Cross-Connection Control & Device Selection
Protecting public drinking water from hazardous contamination is the primary public health directive of the plumbing profession. Cross-connections permit toxic industrial chemicals, agricultural fertilizers, boiler treatment compounds, or raw sewage to enter potable water piping during hydraulic fluctuations. The Uniform Plumbing Code (UPC) Chapter 6 and Iowa Administrative Code 481—Chapter 425 enforce rigorous standards governing cross-connection control, device selection, installation geometries, and annual field testing.
1. Cross-Connection Terminology and Backflow Hydraulics
Cross-Connection : Any physical connection or structural arrangement between a potable water supply system and any non-potable fluid, suspended solid, gas, or pipe containing unsafe substances.
Backflow : The undesirable reversal of flow of water or mixtures of water and other liquids, gases, or substances into the distribution pipes of the potable supply.
Hydraulic Causes of Backflow
Backflow occurs via two distinct hydraulic mechanisms:
Backsiphonage : Backflow caused by negative, sub-atmospheric, or vacuum pressure within the water supply line. Common triggers include municipal main breaks, heavy fire department pumping from nearby hydrants, or undersized supply mains experiencing high-velocity demand.
Backpressure : Backflow caused when the pressure in a downstream non-potable system exceeds the operating supply pressure of the potable water line. Common triggers include booster pumps, boiler heating loops, elevated storage tanks, or thermal expansion.
Hazard Classifications
High Hazard (Health Hazard) : A cross-connection involving any substance that, if introduced into the potable water supply, could cause death, illness, spread disease, or create a toxic hazard (e.g., mortuary tables, chemical feed systems, landscape irrigation with fertigation, commercial boilers).
Low Hazard (Pollution Hazard) : A cross-connection involving a substance that would affect the aesthetic quality of water (color, odor, taste) but does not pose a health or life threat (e.g., food preparation equipment, steam tables, non-toxic fire sprinkler lines).
2. Comprehensive Backflow Assembly Selection Matrix
Selecting the correct backflow prevention assembly depends on three criteria: hazard level (high vs. low), hydraulic condition (backsiphonage vs. backpressure), and continuous vs. non-continuous pressure application.
Assembly / Device Type ASSE Standard Hazard Level Hydraulic Conditions Continuous Pressure Rated? Min. Installation Height
Air Gap (AG) ASME A112.1.2 High & Low Hazard Backsiphonage & Backpressure N/A (Physical Gap) 2x Pipe Diameter (Min 1")
Reduced Pressure Principle (RP / RPBP) ASSE 1013 High & Low Hazard Backsiphonage & Backpressure Yes (24 Hours/Day) 12" to 36" above floor
Double Check Valve (DC / DCVA) ASSE 1015 Low Hazard Only Backsiphonage & Backpressure Yes (24 Hours/Day) 12" to 36" above floor
Pressure Vacuum Breaker (PVB) ASSE 1020 High & Low Hazard Backsiphonage ONLY Yes (24 Hours/Day) 12" above highest outlet
Atmospheric Vacuum Breaker (AVB) ASSE 1001 High & Low Hazard Backsiphonage ONLY NO (Max 12 hr / 24 hr) 6" above highest outlet
- Dual Check Valve w/ Vent ASSE 1012 Low Hazard Backsiphonage & Backpressure Yes (Residential Boilers) N/A
- Hose Connection Vacuum Breaker ASSE 1011 High & Low Hazard Backsiphonage ONLY NO Threaded on Hose Bibb
- 3. Mechanical Design and Operating Principles
- 1. Air Gap (AG)
An Air Gap is a non-mechanical, unobstructed vertical physical distance through the free atmosphere between the lowest opening of a supply pipe and the flood level rim of a fixture or receptor. The minimum air gap MUST be at least two times (2x) the effective internal diameter of the supply pipe, but never less than 1.0 inch (25.4 mm) (or 1.5 inches if near vertical walls).
2. Reduced Pressure Principle Backflow Preventer (RPBP / RP - ASSE 1013)
Consists of two independently acting, spring-loaded check valves separated by a hydraulically operating, differential pressure relief valve. If either check valve leaks or if supply pressure drops, the relief valve opens to atmosphere, discharging water and maintaining an internal relief zone pressure at least 2.0 psi lower than supply pressure. Provides ultimate protection for high-hazard commercial boilers, chemical feeds, and industrial plants. Must be installed horizontally with an air-gapped drain funnel.
3. Pressure Vacuum Breaker (PVB - ASSE 1020)
Contains an independently operating, spring-loaded check valve and an internal spring-loaded air inlet valve. Under backsiphonage conditions, the check valve closes and the air inlet valve snaps open to break the vacuum. Must be installed at least 12 inches (305 mm) above the highest downstream piping or overflow rim. Commonly used on commercial irrigation systems.
4. Atmospheric Vacuum Breaker (AVB - ASSE 1001)
Contains a float check valve that rises to seal an air vent under positive pressure and drops to admit air when pressure falls to zero. Critical Rules for AVBs :
Cannot be subjected to continuous water pressure for more than 12 hours in any 24-hour period .
MUST NOT have any shutoff valves or control valves installed downstream of the device.
Must be installed at least 6 inches (152 mm) above all downstream piping and outlets.
4. Iowa's Containment Program (Rule 481—425.5)
Everything above is isolation — protecting the building's own potable system at the point of hazard. Iowa layers a second, utility-side requirement on top of it called containment , and it has its own rule number.
Rule 481—425.5(105) requires cities with populations of 15,000 or greater , as determined by the 2010 census or any subsequent regular or special census, to have a backflow prevention program with containment . These requirements are in addition to the applicable requirements of UPC Section 603 .
What containment means
Containment places an approved backflow prevention assembly on the water service, as close to the public water main as practical — one assembly protecting the whole public system from that customer, regardless of what happens inside the building.
Who administers it
The administrative authority for this rule is the city council and its designees , or, for private water utilities, the Iowa Utilities Board . Not the Plumbing and Mechanical Systems Board — which is consistent with Iowa's general rule that permits, inspection, and enforcement are local.
Approval and listing chain
An approved containment assembly must be approved by the University of Southern California Foundation for Cross-Connection Control and Hydraulic Research , with the approval listing stating the limitations of use based on degree of hazard, and be listed by IAPMO or ASSE as meeting one of these standards:
- Standard Product covered
- ANSI/ASSE 1013 Reduced pressure principle backflow preventers
- ANSI/ASSE 1015 Double check backflow prevention assembly
- ANSI/ASSE 1047 Reduced pressure detector backflow preventer
- ANSI/ASSE 1048 Double check detector assembly backflow preventer
- ANSI/AWWA C510 Double check valve backflow prevention assembly
- ANSI/AWWA C511 Reduced-pressure principle backflow prevention assembly
Assemblies used for containment in a fire protection system must additionally meet Factory Mutual (FM) and Underwriters Laboratories (UL) requirements.
Selection by degree of hazard
High hazard — protected by an air gap or an approved reduced-pressure principle assembly .
Low hazard — protected by an approved double check valve assembly , or by the high-hazard option.
Fire protection systems — protected in accordance with AWWA Manual M14, fourth edition .
Procedural duties
New or reconstructed service: no one may install a water service before the administrative authority has evaluated it for degree of hazard, and the owner installs the required assembly before water service is initiated . A reconstructed existing service is treated as a proposed service.
Existing services: each customer must survey the activities and processes served by the water service and report cross connections and degree of hazard. The administrative authority may inspect, may require an assembly, and may order water service discontinued if the customer refuses.
Placement: containment assemblies are installed immediately following the water meter , or as close to that location as the administrative authority deems practical.
Backflow incidents: the customer must immediately notify the agency providing water service upon becoming aware that backflow has occurred, and the administrative authority may temporarily shut off the service.
Important
Isolation and containment answer different questions. Isolation asks "what device protects the building's own water at this fixture or piece of equipment?" — that is UPC Section 603 and the selection matrix above. Containment asks "what device protects the public main from this entire property?" — that is rule 481—425.5, it applies in cities of 15,000 or more, and the assembly sits right after the meter.