Study guide
4.1 Ramps: Slopes, Landings, and Clearances
ICC Accessibility Inspector / Plans Examiner 21
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: General Administrative and Scoping Provisions
1.1 Occupancy Group Accessibility and IBC Chapter 11 Scoping 1.2 General Administration: Definitions, Conventions, and Code Editions 1.3 Existing Buildings: IEBC Section 306 Alterations, Additions, and Changes of Occupancy 1.4 Technical Infeasibility, Existing-Building Ramps, and Historic Structures
2 Chapter 2: Building Blocks (ICC A117.1 Chapter 3)
2.1 Walking and Floor Surfaces, Openings, and Level Changes 2.2 Turning Space and Clear Floor Space: New Versus Existing Buildings 2.3 Knee and Toe Clearances 2.4 Unobstructed and Obstructed Reach Ranges 2.5 Protruding Objects and Vertical Clearance
3 Chapter 3: Accessible Routes — Route Scoping, Entrances, and Doors
3.1 Accessible Route Scoping, Components, Slopes, and Clear Width 3.2 Accessible Entrances: Number, Location, and Power-Operated Doors 3.3 Doors, Doorways, and Gates: Clear Width and Maneuvering Clearances 3.4 Door Hardware, Forces, Closing Speed, Door Surfaces, and Windows
4 Chapter 4: Accessible Routes — Ramps, Curb Ramps, and Conveyance
4.1 Ramps: Slopes, Landings, and Clearances 4.2 Ramp Handrails, Edge Protection, and Cross Slopes 4.3 Curb Ramps, Blended Transitions, and Detectable Warnings at Crossings 4.4 Elevators, LULA Elevators, and Platform Lifts
5 Chapter 5: Accessible Means of Egress
5.1 Accessible Means of Egress: Number, Components, Elevators, and Stairways 5.2 Elevators, Platform Lifts, Areas of Refuge, and Exterior Areas for Assisted Rescue 5.3 Two-Way Communication, Egress Signage, and Instructions
6 Chapter 6: General Site and Building Elements
6.1 Accessible Parking: Scoping, Van Spaces, Dimensions, and Signs 6.2 Passenger Loading Zones, Bus Stops, and Rail Platforms 6.3 Site Accessibility: Site Routes, Routes Through Parking, EV Charging, and Fuel Dispensers 6.4 Stairways: Treads, Risers, Nosings, Visual Contrast, and Lighting 6.5 Stair Handrails: Location, Height, Profile, Continuity, and Extensions
7 Chapter 7: Plumbing Elements and Facilities
7.1 Water Closets and Toilet Compartments 7.2 Grab Bars: Locations, Cross Sections, Spacing, Strength, and Assisted Toileting 7.3 Toilet Rooms, Lavatories, Sinks, Mirrors, Urinals, and Accessories 7.4 Bathtubs, Shower Compartments, and Seats 7.5 Plumbing Scoping: Family Rooms, Adult Changing Stations, Drinking Fountains, Laundry, and Saunas
8 Chapter 8: Communication Elements and Features
8.1 Visible Alarms and Assistive Listening Systems 8.2 Accessible Signage: Visual Characters, Raised Characters, Braille, Pictograms, and Symbols 8.3 Telephones, ATMs and Fare Machines, Two-Way Communication Systems, and Detectable Warnings
9 Chapter 9: Special Rooms and Spaces
9.1 Assembly Areas: Wheelchair Spaces, Companion Seats, Dispersion, and Lines of Sight 9.2 Dressing and Locker Rooms, Courtrooms, Detention Cells, Self-Storage, and Classroom Acoustics 9.3 Kitchens and Kitchenettes
10 Chapter 10: Built-in Furnishings and Equipment
10.1 Dining Surfaces and Work Surfaces 10.2 Sales and Service Counters and Windows 10.3 Check-Out Aisles, Food Service Lines, Benches, Storage, Charging Stations, and Gaming
11 Chapter 11: Dwelling and Sleeping Units
11.1 Scoping Accessible, Type A, and Type B Units (IBC 1108) 11.2 Type A Units (A117.1 Section 1103) 11.3 Type B Units (A117.1 Section 1104) 11.4 Accessible Units: Hotels, Dormitories, Health Care and Residential Care (A117.1 Section 1102) 11.5 Type C (Visitable) Units and Units with Communication Features
12 Chapter 12: Recreational Facilities
12.1 Swimming Pools, Wading Pools, Hot Tubs, and Spas 12.2 Play Areas and Amusement Rides 12.3 Sports Facilities, Exercise Equipment, Golf, Boating, Fishing, and Shooting Facilities
4.1 Ramps: Slopes, Landings, and Clearances
Key Takeaways Explain This Topic AI
Ramp runs have a running slope steeper than 1:20 and not steeper than 1:12, a cross slope not steeper than 1:48, and a 30-inch maximum rise per run.
Ramp runs are 36 inches clear minimum, with handrails and supports kept out of that width; IBC 1012.5.1 can require more width for egress ramps.
Landings are at the top and bottom of every run, at least as wide as the widest run, 60 inches long, and 60 x 60 inches where the ramp changes direction.
Door maneuvering clearances may overlap a ramp landing, and a landing beside a door subject to locking must provide a turning space (405.7.5).
In existing buildings with space limitations, Table 405.2 allows up to 1:10 for a 6-inch rise and up to 1:8 for a 3-inch rise.
Last updated: October 2026
4.1 Ramps: Slopes, Landings, and Clearances
Quick Reference: Running slope maximum is 1:12 (8.33%) . Maximum vertical rise for any single ramp run is 30 inches (760 mm) . Minimum clear width between handrails is 36 inches (915 mm) . Top, bottom, and intermediate landings must provide a minimum clear length of 60 inches (1525 mm) in the direction of travel. Landings at changes of direction require a 60 by 60 inch (1525 x 1525 mm) minimum turning space. Handrails are required on both sides when the vertical rise exceeds 6 inches (150 mm) .
In accessibility plan examination and field inspection, ramps represent one of the most critical structural components of the accessible route. When site topography, finished floor elevations, or architectural changes in level create vertical separations that cannot be negotiated by standard walking surfaces, ramps provide an essential means of unassisted mobility for individuals using wheelchairs, scooters, walkers, strollers, and crutches. Independent ICC 21 prep by ExamFinch emphasizes understanding the precise mathematical relationships, physical mechanics, and scoping thresholds defined in ICC A117.1 Section 405 and IBC Section 1012 .
Ramp Slope Fundamentals and Calculations
Under ICC A117.1 Section 405.1 , any walking surface on an accessible route that has a running slope steeper than 1:20 (5.0% or 1 unit vertical in 20 units horizontal) is classified as a ramp and must strictly comply with all provisions of Section 405. Surfaces with slopes of 1:20 or flatter are classified as accessible walking surfaces (regulated by Section 403) and do not require ramp landings, handrails, or edge protection.
Maximum Running Slope
Under ICC A117.1 Section 405.2 , the maximum allowable running slope for any newly constructed ramp run is 1:12 (8.33%) . This means that for every 1 inch (25 mm) of vertical rise, there must be at least 12 inches (305 mm) of horizontal ramp run.
Slope = Rise Run ≤ 1 12 ≈ 0.0833 ( 8.33 % \text{Slope} = \frac{\text{Rise}}{\text{Run}} \le \frac{1}{12} \approx 0.0833 \quad (8.33\% Slope = Run Rise ≤ 12 1 ≈ 0.0833 ( 8.33%
Minimum Required Run = Rise × 12 \text{Minimum Required Run} = \text{Rise} \times 12 Minimum Required Run = Rise × 12
Slope Equivalents Reference Table
Slope Ratio (Vertical : Horizontal) Decimal Fraction Slope Percentage Inches of Run per Inch of Rise Classification / Application
- 1:48 0.0208 2.08% 48 inches (4.0 ft) Maximum cross slope on ramps & landings
- 1:20 0.0500 5.00% 20 inches (1.67 ft) Maximum slope for accessible walking route
- 1:16 0.0625 6.25% 16 inches (1.33 ft) Recommended comfortable ramp slope
- 1:12 0.0833 8.33% 12 inches (1.0 ft) Maximum allowable slope for new ramps
- 1:10 0.1000 10.00% 10 inches (0.83 ft) Existing buildings with space limitations, max 6-inch rise
- 1:8 0.1250 12.50% 8 inches (0.67 ft) Existing buildings with space limitations, max 3-inch rise
- Plan Review Mathematical Scenarios
Plans examiners must frequently calculate whether a proposed site plan or architectural section provides adequate spatial length for required ramp runs and landings.
Scenario 1: Single Run Calculation
An entrance to an office suite requires overcoming a finished floor elevation change of 18 inches .
With a maximum allowable slope of 1:12, the horizontal run required is: Run = 18 inches × 12 = 216 inches (18 feet) \text{Run} = 18\text{ inches} \times 12 = 216\text{ inches (18 feet)} Run = 18 inches × 12 = 216 inches (18 feet)
Because the total rise (18 inches) is less than the maximum allowable rise of 30 inches per run, this elevation change can be accomplished in a single ramp run.
The total linear footprint required along the travel axis must include the 18-foot ramp run, a 5-foot (60-inch) top landing, and a 5-foot (60-inch) bottom landing: Total Length = 5 ft (top) + 18 ft (run) + 5 ft (bottom) = 28 feet \text{Total Length} = 5\text{ ft (top)} + 18\text{ ft (run)} + 5\text{ ft (bottom)} = 28\text{ feet} Total Length = 5 ft (top) + 18 ft (run) + 5 ft (bottom) = 28 feet
Scenario 2: Multi-Run Elevation with Intermediate Landing
A community center entrance requires overcoming a vertical rise of 42 inches .
Because 42 inches exceeds the 30-inch maximum allowable rise for a single ramp run, the ramp must be divided into at least two separate runs separated by an intermediate level landing.
Dividing the elevation evenly: two runs, each with a 21-inch rise .
Horizontal run per segment: Run 1 = 21 inches × 12 = 252 inches (21 feet) \text{Run}_1 = 21\text{ inches} \times 12 = 252\text{ inches (21 feet)} Run 1 = 21 inches × 12 = 252 inches (21 feet) Run 2 = 21 inches × 12 = 252 inches (21 feet) \text{Run}_2 = 21\text{ inches} \times 12 = 252\text{ inches (21 feet)} Run 2 = 21 inches × 12 = 252 inches (21 feet)
In a straight linear configuration, the overall length required is: Total Length = 5 ft (top) + 21 ft + 5 ft (intermediate) + 21 ft + 5 ft (bottom) = 57 feet \text{Total Length} = 5\text{ ft (top)} + 21\text{ ft} + 5\text{ ft (intermediate)} + 21\text{ ft} + 5\text{ ft (bottom)} = 57\text{ feet} Total Length = 5 ft (top) + 21 ft + 5 ft (intermediate) + 21 ft + 5 ft (bottom) = 57 feet
If designed as a 180-degree switchback ramp, the intermediate landing must measure at least 60 by 60 inches to accommodate wheelchair turning space.
Maximum Rise and Landing Scoping Criteria
Under ICC A117.1 Section 405.6 , the maximum rise for any single ramp run shall be 30 inches (760 mm) . The code establishes this threshold because ascending a 1:12 ramp over a 30-inch vertical rise requires 30 linear feet of continuous physical exertion. Beyond 30 feet, manual wheelchair users experience acute muscular fatigue, grip exhaustion on handrims, and increased risk of backward tip-overs. Level landings provide critical resting zones where wheelchair users can lock their brakes, recover, and re-orient.
Top and Bottom Landings (Section 405.7.2 & 405.7.3)
Minimum Length: Landings at the top and bottom of each ramp run must have a minimum clear length of 60 inches (1525 mm) measured parallel to the direction of ramp travel.
Minimum Width: The landing width must be at least as wide as the widest ramp run leading to it.
Intermediate Landings (Section 405.7.4)
Intermediate landings between ramp runs in a straight continuous line must have a minimum clear length of 60 inches (1525 mm) in the direction of travel.
Changes of Direction (Section 405.7.4)
Ramps that change direction at landings—such as 90-degree L-turns or 180-degree U-turn switchbacks—must provide a landing measuring at least 60 inches by 60 inches (1525 mm by 1525 mm) minimum clear space. This ensures a full standard turning space complying with Section 304.3.
Slope of Landings (Section 405.7.1)
Ramp landings must be substantially level. The maximum allowable slope in any direction is 1:48 (2.08%) . This allows adequate cross fall for outdoor stormwater drainage while preventing wheelchairs from rolling uncontrollably while stationary.
Doorways at Ramp Landings (Section 405.7.5)
Where a door or gate is adjacent to a ramp landing, the door maneuvering clearances required by Sections 404.2.3 and 404.3.4 are permitted to overlap the landing area . Where a door or gate that is subject to locking is adjacent to a ramp landing, the landing must be sized to provide a turning space complying with Section 304.3 (67-inch circle or a new-building T in new construction), so a person who finds the door locked can turn around without backing down the ramp. The maneuvering clearance itself must be on the level landing, never on the sloped run.
Wet Conditions (Section 405.10)
Landings subject to wet conditions must be designed to prevent the accumulation of water.
Clear Width Requirements and Egress Overlaps
Under ICC A117.1 Section 405.5 , the minimum clear width of an accessible ramp run between handrails shall be 36 inches (915 mm) . Plans examiners must carefully distinguish between the accessible route minimum width and means of egress width requirements:
Accessibility Minimum: 36 inches clear between the inside faces of handrails.
Means of Egress Ramps (IBC Section 1012.5.1): The minimum width and required capacity of a means of egress ramp are not less than those required for corridors by Section 1020.2, and the clear width between handrails, if provided, is 36 inches minimum. In most occupancies that makes an egress ramp 44 inches wide, or 36 inches where the occupant load served is less than 50. IBC Section 1012.2 sets the 1:12 maximum slope for ramps used as part of a means of egress.
Handrail Encroachment: IBC Section 1014.8 (1014.9 in the 2024 IBC) permits handrails to project up to 4.5 inches (114 mm) into the required means of egress width on each side. However, regardless of handrail projections, the net clear width between handrails must never be less than the 36-inch accessibility baseline.
Existing Building Exceptions (Technical Infeasibility)
In existing buildings and facilities, ICC A117.1 Section 405.2 Exception permits ramps steeper than 1:12, complying with Table 405.2, where such slopes are necessary due to space limitations . The exception does not apply to additions, which are new construction.
Allowable Slope Range Slope Percentage Maximum Permitted Rise Code Condition / Restriction
Steeper than 1:12, not steeper than 1:10 8.33% to 10.00% 6 inches (150 mm) Existing buildings, where necessary due to space limitations
Steeper than 1:10, not steeper than 1:8 10.00% to 12.50% 3 inches (75 mm) Existing buildings, where necessary due to space limitations
Steeper than 1:8 > 12.50% PROHIBITED Under no circumstance is a ramp slope steeper than 1:8 permitted on an accessible route
Master Reference Table: Ramp Geometry and Landing Scoping
Feature Code Section Minimum Dimension Maximum Dimension Key Plan Review / Inspection Metric
Ramp Running Slope A117.1 §405.2 > 1:20 (5.0%) 1:12 (8.33%) Slopes ≤ 1 : 20 \le 1:20 ≤ 1 : 20 are walkways; > 1 : 20 > 1:20 > 1 : 20 are ramps
- Ramp Rise per Run A117.1 §405.6 None 30 inches (760 mm) Single run cannot exceed 30 in rise without landing
- Clear Width A117.1 §405.5 36 inches (915 mm) None Measured between inside gripping faces of handrails
- Straight Landing Length A117.1 §405.7.3 60 inches (1525 mm) None Clear length in the direction of travel
- Direction Change Landing A117.1 §405.7.4 60 x 60 inches None Required at 90° turns and 180° switchbacks
- Landing Slope A117.1 §405.7.1 0.0% 1:48 (2.08%) Must be level in all directions (drainage max 1:48)
Door at Landing A117.1 §405.7.5 Maneuvering clearances may overlap landing Turning space if door is subject to locking Clearance must be on the level landing
Handrail Requirement A117.1 §405.8 Rise > 6 inches (150 mm) None Handrails mandatory on both sides of ramp runs
Inspector Field Verification Protocols and Exam Traps
Digital Level Protocols: Use a calibrated 24-inch or 48-inch digital smart level. Place the level parallel to the direction of travel to measure the running slope. Do not place the level across trowel marks, expansion joints, or surface spalls. Take measurements at the bottom, middle, and top of each ramp run.
Handrail Clear Width Trap: Always measure the clear width between the inside gripping surfaces of the handrails , not between the ramp curbs, stringers, or side walls. If an architect specifies a 36-inch concrete slab width and mounts handrails inside the slab edges, the resulting 31-inch clear width between handrails is an immediate code violation.
Landing Drainage Trap: Outdoor landings must shed water, but contractors frequently pour landings with a 1:24 or 1:30 slope to match adjacent asphalt paving. A landing slope steeper than 1:48 (2.08%) violates Section 405.7.1 because an unstable resting surface causes parked wheelchairs to roll downhill.
Door Maneuvering Overlap Trap: When an exterior door swings out onto a ramp landing, verify that the full required door maneuvering clearance (e.g., 60 inches deep by 18 inches latch clearance for a pull-side front approach) rests entirely on the level 1:48 landing surface and does not spill onto the sloped 1:12 ramp run.