Study guide
3.4 Door Hardware, Forces, Closing Speed, Door Surfaces, and Windows
ICC Accessibility Inspector / Plans Examiner 21
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: General Administrative and Scoping Provisions
1.1 Occupancy Group Accessibility and IBC Chapter 11 Scoping 1.2 General Administration: Definitions, Conventions, and Code Editions 1.3 Existing Buildings: IEBC Section 306 Alterations, Additions, and Changes of Occupancy 1.4 Technical Infeasibility, Existing-Building Ramps, and Historic Structures
2 Chapter 2: Building Blocks (ICC A117.1 Chapter 3)
2.1 Walking and Floor Surfaces, Openings, and Level Changes 2.2 Turning Space and Clear Floor Space: New Versus Existing Buildings 2.3 Knee and Toe Clearances 2.4 Unobstructed and Obstructed Reach Ranges 2.5 Protruding Objects and Vertical Clearance
3 Chapter 3: Accessible Routes — Route Scoping, Entrances, and Doors
3.1 Accessible Route Scoping, Components, Slopes, and Clear Width 3.2 Accessible Entrances: Number, Location, and Power-Operated Doors 3.3 Doors, Doorways, and Gates: Clear Width and Maneuvering Clearances 3.4 Door Hardware, Forces, Closing Speed, Door Surfaces, and Windows
4 Chapter 4: Accessible Routes — Ramps, Curb Ramps, and Conveyance
4.1 Ramps: Slopes, Landings, and Clearances 4.2 Ramp Handrails, Edge Protection, and Cross Slopes 4.3 Curb Ramps, Blended Transitions, and Detectable Warnings at Crossings 4.4 Elevators, LULA Elevators, and Platform Lifts
5 Chapter 5: Accessible Means of Egress
5.1 Accessible Means of Egress: Number, Components, Elevators, and Stairways 5.2 Elevators, Platform Lifts, Areas of Refuge, and Exterior Areas for Assisted Rescue 5.3 Two-Way Communication, Egress Signage, and Instructions
6 Chapter 6: General Site and Building Elements
6.1 Accessible Parking: Scoping, Van Spaces, Dimensions, and Signs 6.2 Passenger Loading Zones, Bus Stops, and Rail Platforms 6.3 Site Accessibility: Site Routes, Routes Through Parking, EV Charging, and Fuel Dispensers 6.4 Stairways: Treads, Risers, Nosings, Visual Contrast, and Lighting 6.5 Stair Handrails: Location, Height, Profile, Continuity, and Extensions
7 Chapter 7: Plumbing Elements and Facilities
7.1 Water Closets and Toilet Compartments 7.2 Grab Bars: Locations, Cross Sections, Spacing, Strength, and Assisted Toileting 7.3 Toilet Rooms, Lavatories, Sinks, Mirrors, Urinals, and Accessories 7.4 Bathtubs, Shower Compartments, and Seats 7.5 Plumbing Scoping: Family Rooms, Adult Changing Stations, Drinking Fountains, Laundry, and Saunas
8 Chapter 8: Communication Elements and Features
8.1 Visible Alarms and Assistive Listening Systems 8.2 Accessible Signage: Visual Characters, Raised Characters, Braille, Pictograms, and Symbols 8.3 Telephones, ATMs and Fare Machines, Two-Way Communication Systems, and Detectable Warnings
9 Chapter 9: Special Rooms and Spaces
9.1 Assembly Areas: Wheelchair Spaces, Companion Seats, Dispersion, and Lines of Sight 9.2 Dressing and Locker Rooms, Courtrooms, Detention Cells, Self-Storage, and Classroom Acoustics 9.3 Kitchens and Kitchenettes
10 Chapter 10: Built-in Furnishings and Equipment
10.1 Dining Surfaces and Work Surfaces 10.2 Sales and Service Counters and Windows 10.3 Check-Out Aisles, Food Service Lines, Benches, Storage, Charging Stations, and Gaming
11 Chapter 11: Dwelling and Sleeping Units
11.1 Scoping Accessible, Type A, and Type B Units (IBC 1108) 11.2 Type A Units (A117.1 Section 1103) 11.3 Type B Units (A117.1 Section 1104) 11.4 Accessible Units: Hotels, Dormitories, Health Care and Residential Care (A117.1 Section 1102) 11.5 Type C (Visitable) Units and Units with Communication Features
12 Chapter 12: Recreational Facilities
12.1 Swimming Pools, Wading Pools, Hot Tubs, and Spas 12.2 Play Areas and Amusement Rides 12.3 Sports Facilities, Exercise Equipment, Golf, Boating, Fishing, and Shooting Facilities
3.4 Door Hardware, Forces, Closing Speed, Door Surfaces, and Windows
Key Takeaways Explain This Topic AI
Door hardware must be 34 to 48 inches above the floor, operable with one hand without tight grasping, pinching or twisting, with 15 lbf maximum for push/pull and 28 inch-pounds for rotational operation.
Interior hinged doors and sliding or folding doors open with 5.0 lbf maximum; fire doors use the minimum force permitted by the administrative authority.
Door closers take at least 5 seconds to move from 90 degrees to 12 degrees open; spring hinges take at least 1.5 seconds from 70 degrees to closed.
Automatic door controls comply with Section 309 and need a clear floor space beyond the arc of the door swing.
Where operable windows are provided in an accessible space, at least one needs 8.5 lbf (sliding) or 5 lbf (other) operating force and Section 309 locks.
Last updated: October 2026
3.4 Door Hardware, Opening Force, and Closing Speed
Quick Reference: Door operating hardware must be mounted between 34 inches (865 mm) and 48 inches (1220 mm) above the finish floor and must be operable with one hand without tight grasping, pinching, or twisting of the wrist. The maximum allowable opening force for interior non-fire hinged doors is 5.0 pounds-force (22.2 N) . Door closers must require at least 5 seconds to move from an open position of 90 degrees to an angle of 12 degrees from the latch. Spring hinges must require at least 1.5 seconds to close from a 70-degree open position. Actuator controls for automatic doors must be mounted outside the door swing path.
Even when a doorway provides adequate clear width and generous maneuvering clearances, the door remains impassable if a user cannot grasp the handle, if the closer spring requires excessive physical force to overcome, or if the door slams shut before a user can cross the threshold. Accessibility inspectors and plans examiners must rigorously verify hardware ergonomics, closing timing, and operating resistance. Independent ICC 21 prep by ExamFinch covers the critical technical nuances governing mechanical hardware, fire door exemptions, and automatic operator installations.
Operable Parts and Hardware Ergonomics
Under ICC A117.1 Section 404.2.6 (and IBC Section 1010.2 for egress door hardware), handles, pulls, latches, locks and other operable parts on doors and gates must have a shape that is easy to grasp with one hand and must not require tight grasping, pinching or twisting of the wrist. The 2017 edition also sets operating forces for the hardware itself :
Hardware operated by a forward, pushing or pulling motion: 15 lbf (66.7 N) maximum to retract latches or disengage holding devices.
Hardware operated by a rotational motion: 28 inch-pounds (315 N-cm) maximum.
The "Closed Fist" Rule
Section 404.2.6 mandates that operable hardware must be operable with one hand and must not require tight grasping, pinching, or twisting of the wrist . This standard is universally evaluated in the field using the "closed fist" test:
If an inspector can unlatch and operate the door mechanism using only a closed fist or an elbow, the hardware complies.
If operating the device requires the user to pinch fingers together, wrap their thumb and fingers tightly around a spherical surface, or twist their wrist, the hardware fails.
Compliant vs. Non-Compliant Hardware Types
Hardware Classification Specific Hardware Examples Accessibility Compliance Status
Compliant Hardware Lever-operated handles with curved returns Passes: Operable with a downward push using forearm or closed fist
Compliant Hardware U-shaped architectural pull handles Passes: Allows hand, wrist, or arm insertion without pinching
Compliant Hardware Touch-bar panic hardware / crash bars Passes: Actuated by leaning or pushing body weight against bar
Compliant Hardware Push/pull paddle latches Passes: Operable by pushing or pulling with forearm or palm
Non-Compliant Hardware Standard round or spherical doorknobs Fails: Requires simultaneous tight grip and rotational wrist torque
Non-Compliant Hardware Small thumb-turn deadbolts Fails: Requires fine-motor thumb-and-finger pinching
Non-Compliant Hardware Recessed flush cup pulls on sliding doors Fails: Requires fingernail insertion or pinching to slide door
Non-Compliant Hardware Key-operated deadbolts without lever assist Fails: High resistance and wrist twisting required
Mounting Height Range
Under ICC A117.1 Section 404.2.6.1 , operable parts of door hardware must be 34 inches (865 mm) minimum and 48 inches (1220 mm) maximum above the floor. Where sliding doors are fully open, operating hardware must be exposed and usable from both sides. A117.1-2017 contains no 54-inch exception for door hardware.
Door Opening Force Limits and Code Exemptions
Under ICC A117.1 Section 404.2.8 , the opening force limit is the force for pushing or pulling the door open . The force to retract a latch or disengage a holding device is a separate limit in Section 404.2.6 (15 lbf push or pull, 28 inch-pounds rotational), and the 404.2.8 exception states that latch-retraction limits do not apply to panic hardware, delayed egress devices or fire-rated hardware.
Interior Non-Fire Doors
The maximum operating force for interior swinging doors (other than fire doors), sliding doors, and folding doors is 5.0 pounds-force (lbf) (22.2 N) .
A 5.0 lbf limit ensures that individuals with limited upper-body strength, arthritis, or cardiopulmonary impairments can independently open doors throughout interior offices, conference rooms, and restrooms.
Fire Door Exemption
Fire-rated doors are explicitly EXEMPT from the 5.0 lbf maximum opening force limit.
Section 404.2.8 states that fire doors, and doors required to have panic hardware, break-away features or other features requiring higher opening force for safety, shall have the minimum opening force allowable in the scoping provisions adopted by the administrative authority . Fire doors must self-close and positively latch under NFPA 80 ( Standard for Fire Doors and Other Opening Protectives ), so their closers are set to the lowest force that still reliably latches the door rather than to 5.0 lbf.
Exterior Doors and Building Pressurization
Candidates often wonder why neither the ADA standards nor ICC A117.1 specify a maximum opening force for exterior hinged doors. National standard committees determined that exterior doors cannot reliably comply with a 5.0 lbf limit due to external wind loads, weather-stripping friction, and interior building HVAC pressurization (stack effect). Setting an exterior closer to 5.0 lbf would cause exterior doors to blow open in moderate breezes or fail to latch against building air currents.
Some jurisdictions adopt their own exterior door force limits, and IBC 1105.1.1 requires power-operated doors at accessible public entrances of larger A, B, M and R-1 buildings (Section 3.2).
Door Closing Speed and Sweep Timing
When a person using crutches, a walker, or a wheelchair crosses a doorway, they require sufficient time to clear the threshold before the door swings shut. Rapidly closing doors frequently strike wheelchairs, damage mobility equipment, or knock unstable individuals off balance.
Under ICC A117.1 Section 404.2.7 , closing speeds are regulated for both hydraulic door closers and spring hinges:
1. Hydraulic Door Closers
Door closers shall be adjusted so that from an open position of 90 degrees , the time required to move the door to an angle of 12 degrees from the latch shall be 5 seconds minimum .
Note
The 12-Degree Latch Sweep Transition: A commercial hydraulic door closer has two distinct regulating valves: the "main sweep" valve (from 90 degrees down to approximately 12 degrees) and the "latch sweep" valve (the final 12 degrees to closed). The 5-second timing requirement applies ONLY to the main sweep (90 degrees to 12 degrees). The final 12 degrees is permitted to accelerate slightly to overcome latch bolt friction and ensure positive latching.
2. Spring Hinges
Spring hinges (commonly found on residential self-closing unit entry doors) lack hydraulic fluid damping. Under Section 404.2.7, doors with spring hinges shall be adjusted so that from the open position of 70 degrees , the door will move to the closed position in 1.5 seconds minimum .
Automatic and Power-Assisted Doors
Where manual opening forces or physical clearances cannot be accommodated, automated doors provide compliant access under ICC A117.1 Section 404.3 and reference standards ANSI/BHMA A156.10 (power-operated doors) and ANSI/BHMA A156.19 (power-assist and low-energy power-operated doors).
Dimensional Clear Opening
Automatic doors must provide the standard 32-inch (815 mm) minimum clear opening width in both the power-on and manual power-off operating modes. If a power outage occurs, users must still be able to push the door open to achieve 32 inches clear.
Actuator Controls and Push Plates
Under Section 404.3.7 , manually operated controls for automatic doors must comply with Section 309 (operable within a Section 308 reach range, one hand, 5.0 lbf maximum), and the clear floor space adjacent to the controls must be located beyond the arc of the door swing . A user must not be positioned where the opening leaf strikes the wheelchair. The clear floor space is 30 x 52 inches in new buildings and 30 x 48 inches in existing buildings (Section 305.3). A117.1 does not specify a second low-mounted actuator.
Other Automatic Door Rules
404.3.4 Maneuvering clearances : Power-assisted doors need the manual clearances of 404.2.3. Low-energy and full power automatic doors that are part of an accessible means of egress need maneuvering clearances on the egress side, unless they have standby power or battery backup, remain open when power is off, or are full power sliding doors with a break-away feature.
404.3.5 Thresholds : Same 1/2-inch rule as manual doors.
404.3.9 Break out opening : Full power automatic sliding doors with a break out feature must provide a 32-inch clear break out opening in emergency mode.
Field Inspection Measurement Protocols
Accessibility inspectors conduct door compliance audits using calibrated instruments and standardized procedures:
Measuring Door Opening Force with a Force Meter
Use a calibrated analog push/pull force gauge (fish-scale type) or digital dynamometer.
Place the sensing tip of the gauge perpendicular to the face of the door leaf on the push side, at the height of the latch hardware, approximately 2-1/2 inches from the strike edge of the door leaf.
With the latch retracted (or on a push-pull door without a latch), push steadily until the door leaf begins to swing open.
Observe the force indicator: the force to push or pull the door open must not exceed 5.0 lbf for interior hinged non-fire doors. Measure latch-retraction force separately against the 15 lbf (push or pull) or 28 inch-pound (rotational) limits of Section 404.2.6.
Timing Door Closer Sweep with a Stopwatch
Open the door to an angle of exactly 90 degrees.
Mark or visualize the 12-degree angle from the latch jamb (approximately 7 to 8 inches of leaf opening at the strike edge for a 36-inch door).
Release the door leaf from a dead stop without pushing.
Start the digital stopwatch at the moment of release, and stop the timer when the door leaf reaches the 12-degree mark.
Verify that the elapsed time is 5.0 seconds or greater .
Summary Comparison: Hardware, Forces, and Timing
Door Feature / Component Applicable Code Section Regulatory Limit Field Measurement Technique
Hardware Mounting Height A117.1 §404.2.6 34 in min to 48 in max above AFF Tape measure from finish floor to center of operable part
Interior Non-Fire Door Force A117.1 §404.2.8 5.0 lbf (22.2 N) maximum Push-pull force gauge at latch height, 2.5 in from edge
Interior Sliding / Folding Door Force A117.1 §404.2.8 5.0 lbf (22.2 N) maximum Push-pull force gauge pulling hardware parallel to travel
Fire-Rated Door Opening Force A117.1 §404.2.8 Minimum opening force allowed by the adopted scoping provisions Force needed to self-close and positively latch per NFPA 80
Door Closer Closing Speed A117.1 §404.2.7 5.0 seconds minimum (90° to 12°) Digital stopwatch timed from 90° release to 12° from latch
Spring Hinge Closing Speed A117.1 §404.2.7 1.5 seconds minimum (70° to closed) Digital stopwatch timed from 70° release to fully closed
Automatic Door Control Clear Floor Space A117.1 §404.3.7 Beyond the arc of the door swing (30 x 52 in. new, 30 x 48 in. existing) Tape measure confirming clear space outside door swing arc
Hardware Operating Force A117.1 §404.2.6 15 lbf push/pull; 28 in-lb rotational Force gauge on the latch-retracting motion
Bottom Rail Smooth Surface A117.1 §404.2.9 10 in. smooth surface on push side Tape measure from floor
Vision Lite Bottom Edge A117.1 §404.2.10 43 in. maximum above floor Tape measure from floor to bottom of glazing
Common Exam Traps and Field Inspection Scenarios
The Fire Door Force Trap: Exam questions often state: "An interior fire-rated corridor door requires 12 pounds of force to open. Does this violate ICC A117.1?" The answer is NO. Fire doors are explicitly exempt from the 5.0 lbf limit because fire-containment positive latching per NFPA 80 supersedes accessibility force limits.
The 12-Degree Sweep Trap: Another classic question asks for the elapsed time of a door closer from 90 degrees to fully closed (0 degrees). Candidates who recall "5 seconds" often miss that the 5-second code requirement applies exclusively from 90 degrees to 12 degrees , NOT to full closure.
Actuator in Door Path: On site reviews, automatic push plates are often installed on the wall directly adjacent to the door frame on the pull side. When a wheelchair user presses the button, the door swings directly into their face or chair. The push plate must be offset so that the required clear floor space at the control lies beyond the arc of the door swing (Section 404.3.7).
Door Surfaces and Vision Lites
404.2.9 Door and gate surface : Surfaces within 10 inches of the floor must be smooth on the push side for the full width of the door, so footrests do not catch. Hardware or other protrusions may not be in that zone, joints must be within 1/16 inch of the same plane, and cavities created by added kick plates must be capped. Exceptions: sliding doors; tempered glass doors without stiles whose bottom rail top edge is tapered at least 60 degrees; doors that do not extend to within 10 inches of the floor; and kick plates added to existing doors that extend to 10 inches above the floor and within 1 inch of the sides and bottom.
404.2.10 Vision lites : Doors, gates and sidelites adjacent to doors with one or more viewing panels must have the bottom of at least one panel on the door, gate or an adjacent sidelite 43 inches maximum above the floor. Vision lites whose lowest part is more than 66 inches above the floor are exempt. This provision is new in the 2017 edition.
Windows (A117.1 Section 506)
The outline groups windows with doors. Where operable windows are provided in an accessible room or space, at least one must comply with Section 506; if operable windows are required for natural ventilation or as an emergency escape and rescue opening, that window must be the one that complies. Windows operated only by employees, windows in Type A units complying with Section 1103.13, and operable skylights are exempt.
- Window requirement A117.1 506.2
- Locking and latching operable parts Comply with Section 309
- Opening and closing force, vertical or horizontal sliding windows 8.5 lbf (37.7 N) maximum
- Opening and closing force, all other window types 5 lbf (22.2 N) maximum
- Test method AAMA 513