Study guide

2.3 Knee and Toe Clearances

ICC Accessibility Inspector / Plans Examiner 21

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: General Administrative and Scoping Provisions

1.1 Occupancy Group Accessibility and IBC Chapter 11 Scoping 1.2 General Administration: Definitions, Conventions, and Code Editions 1.3 Existing Buildings: IEBC Section 306 Alterations, Additions, and Changes of Occupancy 1.4 Technical Infeasibility, Existing-Building Ramps, and Historic Structures

2 Chapter 2: Building Blocks (ICC A117.1 Chapter 3)

2.1 Walking and Floor Surfaces, Openings, and Level Changes 2.2 Turning Space and Clear Floor Space: New Versus Existing Buildings 2.3 Knee and Toe Clearances 2.4 Unobstructed and Obstructed Reach Ranges 2.5 Protruding Objects and Vertical Clearance

3 Chapter 3: Accessible Routes — Route Scoping, Entrances, and Doors

3.1 Accessible Route Scoping, Components, Slopes, and Clear Width 3.2 Accessible Entrances: Number, Location, and Power-Operated Doors 3.3 Doors, Doorways, and Gates: Clear Width and Maneuvering Clearances 3.4 Door Hardware, Forces, Closing Speed, Door Surfaces, and Windows

4 Chapter 4: Accessible Routes — Ramps, Curb Ramps, and Conveyance

4.1 Ramps: Slopes, Landings, and Clearances 4.2 Ramp Handrails, Edge Protection, and Cross Slopes 4.3 Curb Ramps, Blended Transitions, and Detectable Warnings at Crossings 4.4 Elevators, LULA Elevators, and Platform Lifts

5 Chapter 5: Accessible Means of Egress

5.1 Accessible Means of Egress: Number, Components, Elevators, and Stairways 5.2 Elevators, Platform Lifts, Areas of Refuge, and Exterior Areas for Assisted Rescue 5.3 Two-Way Communication, Egress Signage, and Instructions

6 Chapter 6: General Site and Building Elements

6.1 Accessible Parking: Scoping, Van Spaces, Dimensions, and Signs 6.2 Passenger Loading Zones, Bus Stops, and Rail Platforms 6.3 Site Accessibility: Site Routes, Routes Through Parking, EV Charging, and Fuel Dispensers 6.4 Stairways: Treads, Risers, Nosings, Visual Contrast, and Lighting 6.5 Stair Handrails: Location, Height, Profile, Continuity, and Extensions

7 Chapter 7: Plumbing Elements and Facilities

7.1 Water Closets and Toilet Compartments 7.2 Grab Bars: Locations, Cross Sections, Spacing, Strength, and Assisted Toileting 7.3 Toilet Rooms, Lavatories, Sinks, Mirrors, Urinals, and Accessories 7.4 Bathtubs, Shower Compartments, and Seats 7.5 Plumbing Scoping: Family Rooms, Adult Changing Stations, Drinking Fountains, Laundry, and Saunas

8 Chapter 8: Communication Elements and Features

8.1 Visible Alarms and Assistive Listening Systems 8.2 Accessible Signage: Visual Characters, Raised Characters, Braille, Pictograms, and Symbols 8.3 Telephones, ATMs and Fare Machines, Two-Way Communication Systems, and Detectable Warnings

9 Chapter 9: Special Rooms and Spaces

9.1 Assembly Areas: Wheelchair Spaces, Companion Seats, Dispersion, and Lines of Sight 9.2 Dressing and Locker Rooms, Courtrooms, Detention Cells, Self-Storage, and Classroom Acoustics 9.3 Kitchens and Kitchenettes

10 Chapter 10: Built-in Furnishings and Equipment

10.1 Dining Surfaces and Work Surfaces 10.2 Sales and Service Counters and Windows 10.3 Check-Out Aisles, Food Service Lines, Benches, Storage, Charging Stations, and Gaming

11 Chapter 11: Dwelling and Sleeping Units

11.1 Scoping Accessible, Type A, and Type B Units (IBC 1108) 11.2 Type A Units (A117.1 Section 1103) 11.3 Type B Units (A117.1 Section 1104) 11.4 Accessible Units: Hotels, Dormitories, Health Care and Residential Care (A117.1 Section 1102) 11.5 Type C (Visitable) Units and Units with Communication Features

12 Chapter 12: Recreational Facilities

12.1 Swimming Pools, Wading Pools, Hot Tubs, and Spas 12.2 Play Areas and Amusement Rides 12.3 Sports Facilities, Exercise Equipment, Golf, Boating, Fishing, and Shooting Facilities

2.3 Knee and Toe Clearances

Key Takeaways Explain This Topic AI

Toe clearance is the space from the floor to 9 inches above it, 30 inches minimum wide, 17 inches minimum deep where required, and 25 inches maximum deep.

Space more than 6 inches beyond the available knee clearance at the 9-inch line is not toe clearance, so a toe kick under solid casework counts for only 6 inches.

Knee clearance runs from 9 to 27 inches above the floor, 30 inches minimum wide, at least 11 inches deep at 9 inches and 8 inches deep at 27 inches, and 25 inches maximum deep.

Knee clearance depth may reduce 1 inch for each 6 inches of height between the 9-inch and 27-inch lines.

Pipes under lavatories and sinks must be insulated or configured to prevent contact under A117.1 Section 606.6.

Last updated: October 2026

2.3 Knee and Toe Clearances

Independent ICC 21 prep by ExamFinch. Wheelchair users seated facing an element require space beneath fixtures for their lower legs and feet. Without adequate recessed space, a seated individual cannot pull close enough to reach faucets, drink from fountain spouts, or write at work surfaces. ICC A117.1 Section 306 defines the exact three-dimensional geometric profile required for toe clearance (Section 306.2) and knee clearance (Section 306.3). These standards apply wherever forward-approach clear floor space or turning space extends beneath counters, lavatories, sinks, drinking fountains, and tables.

Toe Clearance Profile (Section 306.2)

Toe clearance accommodates the user's feet and wheelchair footplates beneath an element.

Vertical and Horizontal Dimensions

Vertical Zone : Space extending between the finish floor and 9 9 9 inches ( 230 230 230 mm) above the finish floor constitutes toe clearance (Section 306.2.1).

Minimum Width : Toe clearance shall be 30 30 30 inches ( 760 760 760 mm) minimum in width throughout its entire depth (Section 306.2.5).

Required Depth at Elements : Where toe clearance is required at an element as part of a forward-approach clear floor space (such as a lavatory or drinking fountain), the toe clearance must extend beneath the element 17 17 17 inches ( 430 430 430 mm) minimum up to a maximum of 25 25 25 inches ( 635 635 635 mm) (Sections 306.2.2 and 306.2.3).

Standalone Toe Clearance Limitation (Section 306.2.4)

A critical inspection rule restricts toe clearance where knee clearance is absent:

Space extending greater than 6 inches (150 mm) beyond the available knee clearance at 9 inches (230 mm) above the floor shall not be considered toe clearance.

The consequence is direct: where there is no knee clearance at the 9-inch line (a solid base cabinet), only the first 6 inches of a toe kick can be counted as toe clearance.

This rule prevents designers from attempting to meet forward clear floor space rules at a solid cabinet or counter by simply providing a deep 9 9 9 -inch high toe kick. Because a seated person cannot insert their knees into solid casework, their feet cannot slide 17 17 17 or 25 25 25 inches forward unless their knees can also advance. Consequently, a standalone toe kick deeper than 6 6 6 inches provides no functional accessibility benefit and cannot be counted as clear floor space.

Knee Clearance Profile (Section 306.3)

Knee clearance accommodates the thighs, knees, and lower legs of a seated user.

Vertical and Horizontal Dimensions

Vertical Zone : Space extending between 9 9 9 inches ( 230 230 230 mm) and 27 27 27 inches ( 685 685 685 mm) above the finish floor constitutes knee clearance (Section 306.3.1).

Leading Edge Height : At the front edge of the counter, apron, or fixture, the underside must be 27 27 27 inches ( 685 685 685 mm) minimum above the finish floor.

Minimum Width : Knee clearance shall be 30 30 30 inches ( 760 760 760 mm) minimum in width throughout its depth (Section 306.3.5).

Maximum Depth : Knee clearance is recognized to a maximum depth of 25 25 25 inches ( 635 635 635 mm) (Section 306.3.2).

The Knee Clearance Taper / Bevel Rule (Section 306.3.3 & 306.3.4)

The human leg angles forward from the hip down toward the feet. To mirror this anatomical profile while allowing structural framing, plumbing traps, and basin bowls to fit under counters, ICC A117.1 permits the knee space to taper:

Depth at 27 Inches : At 27 27 27 inches ( 685 685 685 mm) above the finish floor, knee clearance must extend 8 8 8 inches ( 205 205 205 mm) minimum beneath the front edge of the element.

Depth at 9 Inches : At 9 9 9 inches ( 230 230 230 mm) above the finish floor, knee clearance must extend 11 11 11 inches ( 280 280 280 mm) minimum beneath the front edge of the element.

Permitted Reduction (Bevel) : Between 9 9 9 inches and 27 27 27 inches above the finish floor, the clearance depth is permitted to reduce at a rate of 1 1 1 inch in depth for each 6 6 6 inches in height (a 1 : 6 1:6 1 : 6 slope).

Maximum Taper Slope = 1 : 6 ( depth reduction of 1 " per 6 " vertical rise ) \text{Maximum Taper Slope} = 1:6 \quad (\text{depth reduction of } 1" \text{ per } 6" \text{ vertical rise}) Maximum Taper Slope = 1 : 6 ( depth reduction of 1" per 6" vertical rise )

Notice that the difference between the 11 11 11 -inch depth at the 9 9 9 -inch height and the 8 8 8 -inch depth at the 27 27 27 -inch height is exactly 3 3 3 inches of horizontal depth change across 18 18 18 inches of vertical rise ( 27 " − 9 " = 18 " 27" - 9" = 18" 27" − 9" = 18" ). An 18 18 18 -inch vertical change divided by a 1 : 6 1:6 1 : 6 slope yields exactly 3 3 3 inches ( 18 / 6 = 3 18 / 6 = 3 18/6 = 3 ), precisely matching the required code geometry ( 11 " − 3 " = 8 " 11" - 3" = 8" 11" − 3" = 8" ).

Dimensional Profile Summary Matrix

Clearance Component Elevation Above Finish Floor Minimum Required Depth Maximum Permitted Depth Minimum Required Width Slope / Taper Allowance

Toe Clearance (with knee) Floor to 9 9 9 inches ( 230 230 230 mm) 17 17 17 inches ( 430 430 430 mm) 25 25 25 inches ( 635 635 635 mm) 30 30 30 inches ( 760 760 760 mm) Vertical ( 0 0 0 taper)

Toe Clearance (standalone) Floor to 9 9 9 inches ( 230 230 230 mm) 0 0 0 inches 6 6 6 inches ( 150 150 150 mm) max 30 30 30 inches ( 760 760 760 mm) Vertical

Knee Clearance (lower transition) Exactly 9 9 9 inches ( 230 230 230 mm) 11 11 11 inches ( 280 280 280 mm) 25 25 25 inches ( 635 635 635 mm) 30 30 30 inches ( 760 760 760 mm) Continuous with toe space

Knee Clearance (upper leading edge) Exactly 27 27 27 inches ( 685 685 685 mm) 8 8 8 inches ( 205 205 205 mm) 25 25 25 inches ( 635 635 635 mm) 30 30 30 inches ( 760 760 760 mm) Max 1 : 6 1:6 1 : 6 taper down to 9 9 9 "

Practical Application: Lavatories, Sinks, and Pipe Protection

In public restrooms, lavatories and handwashing sinks are the most critical elements governed by Section 306. Plans examiners and field inspectors must cross-reference Section 306 with Section 606 (Lavatories and Sinks) :

The 34-Inch Rim Height : Under Section 606.3, the rim or counter surface of a lavatory or sink shall be 34 34 34 inches ( 865 865 865 mm) maximum above the finish floor.

The 7-Inch Vertical "Sandwich" : Because the top of the counter is capped at 34 34 34 inches max and the front edge knee clearance underside must be 27 27 27 inches min, the designer has exactly 7 7 7 inches ( 180 180 180 mm) of vertical clearance ( 34 " − 27 " = 7 " 34" - 27" = 7" 34" − 27" = 7" ) to accommodate the counter thickness, sink rim, basin bowl depth, and front apron.

Pipe Protection (Section 606.6) : Water supply lines and drainage piping (P-traps) beneath lavatories and sinks shall be insulated or otherwise configured to protect against contact. There shall be no sharp edges, burrs, or abrasive surfaces under the counter. Uninsulated brass or copper drain lines carrying hot water ( 105 ∘ 105^\circ 10 5 ∘ F to 120 ∘ 120^\circ 12 0 ∘ F) can cause severe burns to individuals with lower-extremity sensory neuropathy.

  • Field Inspection Checkpoints & Plan Examiner Traps
  • Trap 1: The P-Trap Intrusion

Plumbers often install standard drop P-traps that hang down to 6 6 6 or 7 7 7 inches above the floor directly in the center of the knee space. While the front apron meets 27 27 27 inches, the trap encroaches into the 11 11 11 -inch knee depth envelope at the 9 9 9 -inch elevation. Inspectors must verify that offset (grid) drain tailpieces are used to route the P-trap tightly against the rear wall, preserving the 8 8 8 -inch and 11 11 11 -inch knee depths.

Trap 2: Thick Counter Aprons

Millwork contractors frequently design heavy decorative wood fascias that extend 9 9 9 or 10 10 10 inches down from a 34 34 34 -inch counter. This leaves only 24 24 24 or 25 25 25 inches of knee clearance at the front edge, failing the mandatory 27 27 27 -inch threshold. With a 34-inch maximum rim height and a 27-inch minimum knee height at the front edge, the counter, rim and apron together have no more than 7 inches of vertical depth to work with.

Trap 3: Cabinet Base End Panels

When an accessible lavatory is set into custom cabinetry, the side cabinet panels must be spaced at least 30 30 30 inches apart. If trim or filler strips reduce the clear width between cabinet gables to 29 29 29 inches, the installation violates Section 306.2.5 and Section 306.3.5.