Study guide
2.4 Unobstructed and Obstructed Reach Ranges
ICC Accessibility Inspector / Plans Examiner 21
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: General Administrative and Scoping Provisions
1.1 Occupancy Group Accessibility and IBC Chapter 11 Scoping 1.2 General Administration: Definitions, Conventions, and Code Editions 1.3 Existing Buildings: IEBC Section 306 Alterations, Additions, and Changes of Occupancy 1.4 Technical Infeasibility, Existing-Building Ramps, and Historic Structures
2 Chapter 2: Building Blocks (ICC A117.1 Chapter 3)
2.1 Walking and Floor Surfaces, Openings, and Level Changes 2.2 Turning Space and Clear Floor Space: New Versus Existing Buildings 2.3 Knee and Toe Clearances 2.4 Unobstructed and Obstructed Reach Ranges 2.5 Protruding Objects and Vertical Clearance
3 Chapter 3: Accessible Routes — Route Scoping, Entrances, and Doors
3.1 Accessible Route Scoping, Components, Slopes, and Clear Width 3.2 Accessible Entrances: Number, Location, and Power-Operated Doors 3.3 Doors, Doorways, and Gates: Clear Width and Maneuvering Clearances 3.4 Door Hardware, Forces, Closing Speed, Door Surfaces, and Windows
4 Chapter 4: Accessible Routes — Ramps, Curb Ramps, and Conveyance
4.1 Ramps: Slopes, Landings, and Clearances 4.2 Ramp Handrails, Edge Protection, and Cross Slopes 4.3 Curb Ramps, Blended Transitions, and Detectable Warnings at Crossings 4.4 Elevators, LULA Elevators, and Platform Lifts
5 Chapter 5: Accessible Means of Egress
5.1 Accessible Means of Egress: Number, Components, Elevators, and Stairways 5.2 Elevators, Platform Lifts, Areas of Refuge, and Exterior Areas for Assisted Rescue 5.3 Two-Way Communication, Egress Signage, and Instructions
6 Chapter 6: General Site and Building Elements
6.1 Accessible Parking: Scoping, Van Spaces, Dimensions, and Signs 6.2 Passenger Loading Zones, Bus Stops, and Rail Platforms 6.3 Site Accessibility: Site Routes, Routes Through Parking, EV Charging, and Fuel Dispensers 6.4 Stairways: Treads, Risers, Nosings, Visual Contrast, and Lighting 6.5 Stair Handrails: Location, Height, Profile, Continuity, and Extensions
7 Chapter 7: Plumbing Elements and Facilities
7.1 Water Closets and Toilet Compartments 7.2 Grab Bars: Locations, Cross Sections, Spacing, Strength, and Assisted Toileting 7.3 Toilet Rooms, Lavatories, Sinks, Mirrors, Urinals, and Accessories 7.4 Bathtubs, Shower Compartments, and Seats 7.5 Plumbing Scoping: Family Rooms, Adult Changing Stations, Drinking Fountains, Laundry, and Saunas
8 Chapter 8: Communication Elements and Features
8.1 Visible Alarms and Assistive Listening Systems 8.2 Accessible Signage: Visual Characters, Raised Characters, Braille, Pictograms, and Symbols 8.3 Telephones, ATMs and Fare Machines, Two-Way Communication Systems, and Detectable Warnings
9 Chapter 9: Special Rooms and Spaces
9.1 Assembly Areas: Wheelchair Spaces, Companion Seats, Dispersion, and Lines of Sight 9.2 Dressing and Locker Rooms, Courtrooms, Detention Cells, Self-Storage, and Classroom Acoustics 9.3 Kitchens and Kitchenettes
10 Chapter 10: Built-in Furnishings and Equipment
10.1 Dining Surfaces and Work Surfaces 10.2 Sales and Service Counters and Windows 10.3 Check-Out Aisles, Food Service Lines, Benches, Storage, Charging Stations, and Gaming
11 Chapter 11: Dwelling and Sleeping Units
11.1 Scoping Accessible, Type A, and Type B Units (IBC 1108) 11.2 Type A Units (A117.1 Section 1103) 11.3 Type B Units (A117.1 Section 1104) 11.4 Accessible Units: Hotels, Dormitories, Health Care and Residential Care (A117.1 Section 1102) 11.5 Type C (Visitable) Units and Units with Communication Features
12 Chapter 12: Recreational Facilities
12.1 Swimming Pools, Wading Pools, Hot Tubs, and Spas 12.2 Play Areas and Amusement Rides 12.3 Sports Facilities, Exercise Equipment, Golf, Boating, Fishing, and Shooting Facilities
2.4 Unobstructed and Obstructed Reach Ranges
Key Takeaways Explain This Topic AI
Unobstructed forward and side reaches are both 48 inches maximum high and 15 inches minimum low above the floor.
Obstructed forward reach is 48 inches over a reach depth of 20 inches maximum and 44 inches over depths more than 20 and up to 25 inches, with knee and toe clearance under the obstruction.
Obstructed side reach requires an obstruction 34 inches high and 24 inches deep maximum, with 48 inches for reach depths up to 10 inches and 46 inches for depths up to 24 inches.
Existing unaltered elements and fuel dispensers on existing curbs may stay at 54 inches for a side reach under A117.1-2017 308.3.1.
Operable parts must work with one hand at 5.0 lbf maximum, but Section 309.1 exempts items such as dedicated-use receptacles, floor outlets, HVAC diffusers and emergency-only devices.
Last updated: October 2026
2.4 Unobstructed and Obstructed Reach Ranges
Independent ICC 21 prep by ExamFinch. Accessible building elements are only functional if individuals with limited mobility, short stature, or manual dexterity impairments can physically reach and operate them. ICC A117.1 Section 308 establishes the geometric reach envelopes for all operable parts governed by Section 309, including light switches, environmental controls, thermostats, manual fire alarm boxes, elevator call buttons, card access readers, soap dispensers, paper towel dispensers, and electrical convenience receptacles. Plans examiners and accessibility inspectors must distinguish between forward and side approaches and apply precise formulas when obstructions separate the user from the control.
Unobstructed Reach Ranges (Sections 308.2.1 and 308.3.1)
Under modern accessibility standards (including ICC A117.1-2009, 2017, and the 2010 ADA Standards), unobstructed forward reach and unobstructed side (parallel) reach have been harmonized into an identical coordinate envelope.
Unobstructed Forward Reach (Section 308.2.1)
Where a clear floor space complying with Section 305 allows a forward approach, and the reach is unobstructed:
High Forward Reach : 48 48 48 inches ( 1220 1220 1220 mm) maximum above the finish floor.
Low Forward Reach : 15 15 15 inches ( 380 380 380 mm) minimum above the finish floor.
Unobstructed Side Reach (Section 308.3.1)
Where a clear floor space allows a parallel approach alongside an element, and the reach is unobstructed:
High Side Reach : 48 48 48 inches ( 1220 1220 1220 mm) maximum above the finish floor.
Low Side Reach : 15 15 15 inches ( 380 380 380 mm) minimum above the finish floor.
Condition for the Unobstructed Side Reach : Section 308.3.1 applies where the clear floor space allows a parallel approach and the edge of the clear floor space is 10 inches (255 mm) maximum from the element . If the edge is farther away, the reach is obstructed and Section 308.3.2 applies.
Existing Elements Exception : Existing elements that are not altered may remain at 54 inches (1370 mm) maximum, and operable parts of fuel dispensers installed on existing curbs may be 54 inches maximum (308.3.1 Exceptions 1 and 2). New and altered elements must meet 48 inches.
Obstructed High Forward Reach (Section 308.2.2)
When a user must reach forward over an obstruction—such as reaching across a counter or base cabinet to operate a window latch, electrical switch, or plumbing control—the reach geometry changes significantly. Because the user's torso must lean forward over the counter, their vertical reaching capability decreases as the depth of the obstruction increases.
Mandatory Knee and Toe Clearances
Under Section 308.2.2, for an obstructed forward reach to be permitted at all, the clear floor space must extend beneath the obstruction for a distance not less than the required reach depth , and must comply with the knee and toe clearance requirements of Section 306. A user cannot reach forward over a solid counter with no knee space.
Reach Depth Thresholds and Allowable Heights
Reach Depths Up to 20 Inches ( 510 510 510 mm) :
High forward reach is 48 48 48 inches ( 1220 1220 1220 mm) maximum .
Reach Depths Greater Than 20 Inches up to 25 Inches ( 510 510 510 to 635 635 635 mm) :
High forward reach is reduced to 44 44 44 inches ( 1120 1120 1120 mm) maximum .
Absolute Depth Limit :
The maximum permitted depth of an obstruction for a forward reach is 25 25 25 inches ( 635 635 635 mm) . Controls located beyond a 25 25 25 -inch deep counter are strictly non-compliant.
Obstructed Forward Reach: { D ≤ 20 " ⟹ H max = 48 " 20 " < D ≤ 25 " ⟹ H max = 44 " D > 25 " ⟹ PROHIBITED \text{Obstructed Forward Reach: } \begin{cases} D \le 20" & \implies H_{\max} = 48" \\ 20" < D \le 25" & \implies H_{\max} = 44" \\ D > 25" & \implies \text{PROHIBITED} \end{cases} Obstructed Forward Reach: ⎩ ⎨ ⎧ D ≤ 20" 20" < D ≤ 25" D > 25" ⟹ H m a x = 48" ⟹ H m a x = 44" ⟹ PROHIBITED
Obstructed High Side Reach (Section 308.3.2)
In many commercial environments, such as kitchenettes, laboratory benches, and public restrooms, dispensers and switches are mounted on walls directly above continuous base counters where users make a parallel (side) approach.
Counter Height Restriction
A critical requirement often missed on plans examination: under Section 308.3.2, the height of the obstruction shall be 34 34 34 inches ( 865 865 865 mm) maximum above the finish floor. If a base counter is built at standard commercial height ( 36 36 36 inches), an obstructed side reach over that counter is strictly prohibited , regardless of where the control is mounted on the wall.
Reach Depth Thresholds and Allowable Heights
Obstruction Depths Up to 10 Inches ( 255 255 255 mm) :
High side reach is 48 48 48 inches ( 1220 1220 1220 mm) maximum .
Obstruction Depths Greater Than 10 Inches up to 24 Inches ( 255 255 255 to 610 610 610 mm) :
High side reach is reduced to 46 46 46 inches ( 1170 1170 1170 mm) maximum .
Absolute Depth Limit :
The maximum permitted depth of an obstruction for a side reach is 24 24 24 inches ( 610 610 610 mm) . Any control located over a counter deeper than 24 24 24 inches cannot be reached from a parallel approach.
Obstructed Side Reach (Obstruction Height ≤ 34 " ): { D ≤ 10 " ⟹ H max = 48 " 10 " < D ≤ 24 " ⟹ H max = 46 " D > 24 " ⟹ PROHIBITED \text{Obstructed Side Reach (Obstruction Height } \le 34"\text{): } \begin{cases} D \le 10" & \implies H_{\max} = 48" \\ 10" < D \le 24" & \implies H_{\max} = 46" \\ D > 24" & \implies \text{PROHIBITED} \end{cases} Obstructed Side Reach (Obstruction Height ≤ 34" ): ⎩ ⎨ ⎧ D ≤ 10" 10" < D ≤ 24" D > 24" ⟹ H m a x = 48" ⟹ H m a x = 46" ⟹ PROHIBITED
Comprehensive Reach Range Dimensional Matrix
Reach Orientation Obstruction Condition Obstruction Depth ( D D D ) Max Obstruction Height Max High Reach ( H H H ) Min Low Reach Knee / Toe Clearance Required?
Forward Reach Unobstructed None N/A 48 48 48 inches ( 1220 1220 1220 mm) 15 15 15 inches ( 380 380 380 mm) No
Forward Reach Obstructed D ≤ 20 D \le 20 D ≤ 20 inches ( 510 510 510 mm) Must provide knee space 48 48 48 inches ( 1220 1220 1220 mm) 15 15 15 inches ( 380 380 380 mm) Yes (full depth D D D )
Forward Reach Obstructed 20 " < D ≤ 25 " 20" < D \le 25" 20" < D ≤ 25" ( 635 635 635 mm) Must provide knee space 44 44 44 inches ( 1120 1120 1120 mm) 15 15 15 inches ( 380 380 380 mm) Yes (full depth D D D )
Forward Reach Obstructed D > 25 D > 25 D > 25 inches Prohibited Non-compliant Non-compliant N/A
Side (Parallel) Unobstructed (CFS edge 10 in. max from element) D ≤ 10 " D \le 10" D ≤ 10" 34 34 34 inches ( 865 865 865 mm) max if an obstruction is present 48 48 48 inches ( 1220 1220 1220 mm) 15 15 15 inches ( 380 380 380 mm) No
Side (Parallel) Obstructed 10 " < D ≤ 24 " 10" < D \le 24" 10" < D ≤ 24" ( 610 610 610 mm) 34 34 34 inches ( 865 865 865 mm) max 46 46 46 inches ( 1170 1170 1170 mm) 15 15 15 inches ( 380 380 380 mm) No (parallel approach)
- Side (Parallel) Obstructed D > 24 D > 24 D > 24 inches Prohibited Non-compliant Non-compliant N/A
- Operable Parts Requirements (Section 309 Cross-Reference)
Placing an operable part within the reach range is only half of compliance. Under ICC A117.1 Section 309.4, the mechanism itself must comply with three ergonomic criteria:
One-Hand Operation : Operable parts shall be operable with one hand.
No Tight Grasping, Pinching, or Twisting : The operation cannot require tight grasping, tight pinching, or twisting of the wrist. Compliant mechanisms include lever handles, push buttons, U-shaped pulls, rocker switches, and automated sensor controls. Round doorknobs, standard key turn locks, and small toggle switches fail.
Operating Force : The force required to activate operable parts shall be 5.0 5.0 5.0 pounds force ( 22.2 22.2 22.2 N) maximum .
- Field Inspection Checkpoints & Exam Traps
- Trap 1: The 44-Inch vs. 46-Inch Height Confusion
A classic trick on the ICC 21 exam asks for the allowable reach height over a counter. Candidates frequently mix up the forward reach reduction ( 44 44 44 inches for depths between 20 20 20 and 25 25 25 inches) with the side reach reduction ( 46 46 46 inches for depths between 10 10 10 and 24 24 24 inches). Memorize: Forward = 44 44 44 " over deep obstruction; Side = 46 46 46 " over deep obstruction .
Trap 2: The 36-Inch Breakroom Counter Trap
In office breakrooms, standard base cabinets are 36 36 36 inches high and 24 24 24 inches deep. If an architect specifies a paper towel dispenser or microwave shelf mounted above this 36 36 36 -inch high counter:
Side reach is completely invalid because the counter height exceeds 34 34 34 inches (Section 308.3.2).
Forward reach is completely invalid unless the base cabinet is open underneath with 27 27 27 -inch high knee clearance and 9 9 9 -inch high toe clearance extending 24 24 24 inches deep.
If the cabinet has standard closed doors, the dispenser or appliance fails compliance regardless of how low it is hung on the wall!
Trap 3: Electrical Receptacle Box Centerlines
Section 308 requires the operable part (the plug slot of an electrical receptacle) to be at least 15 15 15 inches above the finish floor. In the field, electricians frequently measure 15 15 15 inches to the center of the electrical rough-in box. When a standard duplex receptacle is installed, the lower receptacle slot ends up at approximately 13.5 13.5 13.5 inches above the floor, failing the 15 15 15 -inch minimum threshold. Electrical rough-in boxes must be set with their bottom at least 15 15 15 inches above finish floor.
Operable Parts Exceptions (Section 309.1)
Section 309 applies to every operable part on an accessible element, but Section 309.1 lists items that do not have to comply. These exceptions are frequently tested because they look like ordinary controls:
- Exception Not required to comply with Section 309
- 1 Receptacle outlets serving a dedicated use (a refrigerator or clothes washer outlet)
- 2 In a kitchen, one of two or more receptacles above an uninterrupted countertop length
3 Kitchen countertop receptacles in a corner between appliances where a parallel approach cannot be located, if the countertop area is 9 sq ft maximum
- 4 Floor receptacle outlets
- 5 HVAC diffusers
- 6 Controls mounted on ceiling fans
- 7 One of a set of redundant controls (other than light switches) for a single element in each space
- 8 Reset buttons and shut-offs serving appliances, piping and plumbing fixtures
- 9 Electrical panelboards are exempt from the operation requirement of 309.4 only
10 Emergency devices used only by emergency personnel (fire department hose connections, police call boxes, annunciator panels)
Section 309.2 requires a clear floor space at each operable part, 309.3 places operable parts within one of the Section 308 reach ranges, and 309.4 requires one-hand operation without tight grasping, pinching or twisting of the wrist at 5.0 lbf (22.2 N) maximum. Gas pump nozzles are excepted from the 5.0 lbf force limit.