Study guide
10.2 Masonry Fireplaces, Chimneys & Masonry Heaters
ICC Building Plans Examiner B3
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Administration, Legal Authority & Plan Review Workflow
1.1 Scope, Code Applicability & Administrative Authority 1.2 Permit Submittal Documents & Plan Review Standards 1.3 Alternative Materials, Design Approvals & Special Inspections Administration
2 Chapter 2: Occupancy Classification & Special Use Requirements
2.1 Occupancy Groups A through U Classification 2.2 Mixed Occupancy Principles: Separated, Nonseparated & Accessory Uses 2.3 Special Detailed Requirements: Atriums, High-Rise, Underground & Hazardous Uses
3 Chapter 3: Building Height, Area & Construction Types
3.1 Types of Construction (Types I–V) & Fire-Resistance Ratings 3.2 Allowable Building Heights, Stories & Mezzanines 3.3 Allowable Area Calculations & Frontage Increases
4 Chapter 4: Fire-Resistance-Rated Construction & Passive Protection
4.1 Fire Walls, Fire Barriers & Fire Partitions 4.2 Smoke Barriers, Smoke Partitions & Shaft Enclosures 4.3 Opening Protectives, Fire Dampers & Penetration Firestopping 4.4 Exterior Wall Fire-Resistance Ratings & Fire Separation Distance 4.5 Fireblocking, Draftstopping & Concealed Space Protection
5 Chapter 5: Fire Protection & Life Safety Systems
5.1 Automatic Sprinkler Systems & Standpipes 5.2 Fire Alarm, Detection & Smoke Control Systems 5.3 Fire Extinguishers & Special Hazard Suppression Systems
6 Chapter 6: Means of Egress: Design, Capacity & Arrangement
6.1 Occupant Load Determination & Egress Sizing 6.2 Egress Arrangement: Exit Access, Common Path & Travel Distance 6.3 Corridors, Doors, Hardware & Panic Devices 6.4 Exits, Stairways, Ramps & Exit Discharge 6.5 Emergency Escape & Rescue Openings and Assembly Seating Egress
7 Chapter 7: Structural Provisions, Foundations & Materials
7.1 Structural Design Loads: Dead, Live, Snow, Wind & Seismic 7.2 Soils, Footings, Deep Foundations & Retaining Walls 7.3 Structural Materials & Framing: Concrete, Masonry, Steel & Wood 7.4 Special Inspections, Structural Observations & Testing 7.5 Floor Systems: Framing, Sheathing, Bearing & Crawl Spaces 7.6 Concrete Slabs-on-Ground, Exterior Decks & Balconies
8 Chapter 8: Accessibility & Usable Facilities
8.1 IBC Chapter 11 Scoping & Accessible Route Requirements 8.2 Accessible Building Elements: Doors, Ramps, Elevators & Parking 8.3 Plumbing Fixtures, Toilet Rooms & Bathing Facilities 8.4 Dwelling Units, Assembly Areas & Communication Elements
9 Chapter 9: Interior Finishes, Building Envelope & Environmental Systems
9.1 Interior Wall, Ceiling & Floor Finishes: Flame Spread & Smoke Development 9.2 Exterior Walls, Weather Protection & Veneers 9.3 Roof Assemblies, Roof Coverings & Drainage 9.4 Glass, Glazing, Light, Ventilation & Sanitation Requirements 9.5 Interior Wall & Ceiling Coverings: Gypsum Panel Products, Lath & Plaster 9.6 Roof-Ceiling Assemblies: Trusses, Attic Ventilation, Insulation & Access
10 Chapter 10: Building Services, Special Construction & Construction Safeguards
10.1 Building Services & Special Construction: Elevators, Membrane, Temporary Structures, Marquees & Signs 10.2 Masonry Fireplaces, Chimneys & Masonry Heaters 10.3 Safeguards During Construction & Protection of Adjacent Property
10.2 Masonry Fireplaces, Chimneys & Masonry Heaters
Key Takeaways Explain This Topic AI
Masonry chimneys must extend at least 2 feet higher than any portion of the building within 10 feet and at least 3 feet above the highest point of roof penetration (IBC 2113.9).
Masonry firebox back and side walls must be 8 inches of solid masonry including a 2-inch firebrick lining, or 10 inches where no lining is provided (IBC 2111.6).
Hearth extensions must project 16 inches in front and 8 inches beyond each side, increasing to 20 inches and 12 inches where the fireplace opening is 6 square feet or larger.
Masonry fireplace clearance to combustibles is 2 inches at the front and sides and 4 inches at the back, while masonry chimney clearance is 2 inches interior and 1 inch exterior.
Fireplace and chimney footings must be at least 12 inches thick and project at least 6 inches beyond the face on all sides, founded below frost depth.
Last updated: August 2026
1. Why Fireplaces and Chimneys Appear on a Commercial Plans Exam
Masonry fireplaces and chimneys are prescriptive, dimension-heavy provisions in IBC Chapter 21 (Masonry) that appear in hotels, restaurants, clubhouses, senior housing and mixed-use residential projects. They are also examiner-friendly test material because every requirement is a number that can be checked directly on a section detail.
Three code sections carry the content: Section 2111 Masonry Fireplaces , Section 2112 Masonry Heaters , and Section 2113 Masonry Chimneys . Factory-built fireplaces and chimneys are listed appliances governed by UL 127 and UL 103 and installed per their listings, with fireblocking per IBC 718.2.5.1 .
Construction documents (2111.2) must describe in sufficient detail the location, size and construction of masonry fireplaces, including material thicknesses and clearances from walls, partitions and ceilings . A plan set that shows only a fireplace symbol is incomplete.
2. Masonry Fireplace Dimensions (IBC 2111)
Element Requirement Section
Footing thickness 12 inches minimum , extending 6 inches beyond the face on all sides, below frost depth 2111.3
- Footing depth (no freezing) 12 inches minimum below finished grade 2111.3
- Firebox back and side walls, with lining 8 inches solid masonry including a 2-inch firebrick lining 2111.6
- Firebox back and side walls, no lining 10 inches of solid masonry 2111.6
- Firebox depth 20 inches minimum 2111.7
Rumford exception Depth not less than 12 inches and not less than one-third the opening width; throat not less than 12 inches above the lintel 2111.7
- Throat above the opening 8 inches minimum , throat opening 4 inches minimum depth 2111.7, 2111.8
- Lintel bearing 4 inches minimum each end, noncombustible lintel 2111.8
- Damper location 8 inches minimum above the top of the opening , ferrous metal, operable from the room 2111.8.1
Smoke chamber walls 8 inches solid masonry , or 6 inches with a 2-inch firebrick or 5/8-inch vitrified clay lining 2111.9
Hearth thickness 4 inches minimum 2111.10.1
Hearth extension thickness 2 inches minimum (3/8 inch permitted where the firebox is raised 8 inches above the extension) 2111.10.2
- Hearth extension, opening under 6 sq ft 16 inches in front, 8 inches beyond each side 2111.11
- Hearth extension, opening 6 sq ft or larger 20 inches in front, 12 inches beyond each side 2111.11
- Clearance to combustibles 2 inches front and sides, 4 inches at the back 2111.12
Four exceptions modify the clearance rule (2111.12): listed and labeled UL 127 fireplaces may contact combustibles per their listing; where the fireplace is part of a masonry or concrete wall, combustibles must be 12 inches from the inside surface of the nearest firebox lining ; exposed combustible trim and sheathing edges may abut the sidewalls and hearth extension if they stay 12 inches from the firebox lining ; and combustible mantels may not be within 6 inches of the opening , with material within 12 inches above the opening limited to 1/8-inch projection per inch of clearance from the opening.
Fireblocking (2111.13): spaces between fireplaces and the floors and ceilings they pass through must be fireblocked with noncombustible material , to a depth of 1 inch between wood joists, beams or headers, placed only on strips of metal or metal lath.
Exterior combustion air (2111.14): required unless the room is mechanically ventilated and controlled so the indoor pressure is neutral or positive. The intake may not be in a garage, attic, basement or crawl space, may not be higher than the firebox, and must be screened with 1/4-inch mesh . The passageway is 6 to 55 square inches , and unlisted ducts need 1-inch clearance to combustibles within 5 feet of the outlet.
Seismic (2111.4, 2111.5): no seismic reinforcement in SDC A or B ; in SDC C or D , four No. 4 continuous vertical bars anchored in the foundation for chimneys up to 40 inches wide, plus two more bars for each additional 40 inches, tied with 1/4-inch ties at 18 inches on center ; in SDC E or F , full Chapter 21 engineered reinforcement. Anchorage uses two 3/16-inch by 1-inch straps at each floor, ceiling or roof line more than 6 feet above grade, embedded 12 inches into the chimney and bolted to at least four joists with two 1/2-inch bolts.
3. Masonry Chimneys (IBC 2113)
Footings (2113.2): same as fireplaces — 12 inches thick, 6-inch projection , below frost depth.
Termination (2113.9): the classic 3-2-10 rule — chimneys must extend not less than 2 feet higher than any portion of the building within 10 feet , and not less than 3 feet above the highest point where the chimney passes through the roof .
Caps and spark arrestors (2113.9.1, 2113.9.2): a concrete, metal or stone cap sloped to shed water with a drip edge and caulked bond break per ASTM C1283 ; spark arrestor screens with net free area at least four times the flue outlet , heat and corrosion resistance equivalent to 19-gage galvanized or 24-gage stainless steel, and openings that block a 1/2-inch sphere but pass a 3/8-inch sphere .
Wall thickness (2113.10): 4 inches nominal minimum of concrete, solid masonry units, or hollow units grouted solid.
Lining (2113.11, 2113.12): chimneys must be lined; clay flue liners comply with ASTM C315 and are installed per ASTM C1283 , extending from 8 inches below the lowest inlet (or from the top of the smoke chamber for fireplaces) and laid in medium-duty refractory mortar with the maximum slope 30 degrees from vertical .
Multiple flues (2113.14): flues in the same chimney are separated by 4-inch-thick masonry wythes bonded into the chimney walls, except that two flues venting a single appliance may adjoin with joints staggered 4 inches .
Flue area (2113.16.1): round flues need a net area of at least 1/12 of the fireplace opening ; square flues and rectangular flues with an aspect ratio under 2:1 need 1/10 ; rectangular flues with an aspect ratio of 2:1 or more need 1/8 .
Cleanouts (2113.18): provided within 6 inches of the base of each flue , with the upper edge at least 6 inches below the lowest inlet , an opening height of 6 inches minimum , and a noncombustible cover — except where fireplace flues can be cleaned through the fireplace opening.
Clearances (2113.19): 2 inches of airspace to combustibles for chimneys inside the building or within an exterior wall, and 1 inch for chimneys entirely outside the exterior walls, including where they pass through a soffit or cornice. The airspace may not be filled except for fireblocking under 2113.20.
Medium- and high-heat appliance chimneys (2113.11.2, 2113.11.3): medium-heat chimneys have 8-inch solid masonry walls (12-inch stone), a 4 1/2-inch medium-duty refractory brick lining , 4-inch clearance to combustibles , and terminate 10 feet above any building portion within 25 feet ; high-heat chimneys use double 8-inch walls with a 2-inch airspace , high-duty refractory lining, and terminate 20 feet above any building portion within 50 feet .
Masonry heaters (2112) are distinct appliances complying with ASTM E1602 or listed to UL 1482 or EN 15250 , with a 4-inch minimum noncombustible firebox floor and a 36-inch clearance to combustibles unless a reduction method under NFPA 211 Section 12.6 is used, with the clearance space fully vented.
4. Plan Review Scenario: Lodge Great-Room Fireplace
Submittal: a Group R-1 mountain lodge in Seismic Design Category D with a masonry fireplace in the great room. The detail shows a 24-inch-wide by 30-inch-high opening (5 square feet), an 18-inch firebox depth, 8-inch solid masonry side walls with a 2-inch firebrick lining, a 12-inch hearth extension in front, a wood mantel 5 inches above the opening, a chimney terminating 3 feet above its roof penetration with a ridge 8 feet away and 2 feet higher, and no vertical reinforcing shown.
Examiner findings:
Firebox depth. 18 inches is below the 20-inch minimum (2111.7); the Rumford exception requires a documented Rumford design.
Hearth extension. With an opening under 6 square feet, the extension must be 16 inches in front and 8 inches beyond each side (2111.11); 12 inches fails.
Mantel clearance. Combustible mantels may not be placed within 6 inches of the opening (2111.12 Exception 4).
Chimney termination. With a ridge 8 feet away and 2 feet higher, the chimney must extend 2 feet above that ridge — the 3-foot-above-penetration dimension alone is not sufficient (2113.9).
Seismic reinforcement. In SDC D, provide four No. 4 vertical bars with 1/4-inch ties at 18 inches on center and the strap anchorage of 2111.5.
Combustion air. Provide an exterior air intake with 1/4-inch mesh screening and a passageway between 6 and 55 square inches (2111.14).
5. Common Plan Review and Exam Traps
Trap 1: Reading 3-2-10 as "3 feet is always enough." Both conditions apply: 3 feet above the penetration and 2 feet above anything within 10 feet.
Trap 2: Using the 16/8 hearth extension for a large opening. Openings 6 square feet or larger need 20 inches and 12 inches .
Trap 3: Confusing firebox wall thickness. 8 inches with a 2-inch firebrick lining, 10 inches without .
Trap 4: Swapping chimney clearances. 2 inches interior, 1 inch exterior — the opposite of what intuition suggests.
Trap 5: Assuming seismic reinforcement everywhere. SDC A and B require none ; SDC C and D use the prescriptive bars; SDC E and F require engineered design.