Study guide
9.3 Fire and Smoke Protection Features (IBC Chapters 7 & 8)
ICC Certified Building Official CBO
Track your progress as you read
Finished sections get a check mark.
1 Introduction
About the ICC CBO Exam How to Use This Guide
2 Chapter 1: Legislative and Alternative Methods
1.1 Code Adoption and Local Amendments 1.2 Board of Appeals and Alternative Materials/Methods
3 Chapter 2: Code Enforcement and Due Process
2.1 Permits and Construction Documents 2.2 Inspection Process and Certificate of Occupancy 2.3 Notices, Violations, and Stop Work Orders 2.4 Right of Entry and Administrative Warrants 2.5 Due Process and Equal Protection 2.6 Hazard Abatement and Emergency Measures 2.7 Tort Liability and Sovereign Immunity 2.8 Code Enforcement Prosecution and Civil Remedies
4 Chapter 3: Human Resources in Code Administration
3.1 Anti-Discrimination Laws in Public Employment (ADA, Title VII) 3.2 Wage, Hour, and Safety Laws (FLSA, OSHA) 3.3 Personnel Discipline, Performance, and Dismissal 3.4 Labor Relations, Grievances, and Due Process
5 Chapter 4: Reports and Public Records
4.1 Records Management and Document Retention 4.2 Public Records Disclosure and Freedom of Information Laws
6 Chapter 5: Customer Service and Public Relations
5.1 Customer Service Principles in Public Administration 5.2 Public Relations, Media, and Stakeholder Communication 5.3 Interagency Cooperation and Coordination 5.4 Conflict De-escalation and Dispute Resolution 5.5 Feedback Strategy and Continuous Service Improvement
7 Chapter 6: Personnel Administration
6.1 Job Descriptions and Personnel Needs Assessment 6.2 Recruitment, Selection, and Onboarding Processes 6.3 Staff Training, Professional Goals, and Certification 6.4 Performance Appraisals and Supervision Standards
8 Chapter 7: Financial Management
7.1 Operating and Capital Budget Development 7.2 Fee Structures, Valuation, and Revenue Generation 7.3 Financial Controls, Audits, and Cost Recovery
9 Chapter 8: Department Records and Information Systems
8.1 Permitting and Code Enforcement Reporting Systems 8.2 Electronic Document Review and Workflow Integration 8.3 Information Security, Data Privacy, and Disaster Recovery
10 Chapter 9: Architectural Plan Review
9.1 Use and Occupancy Classifications (IBC Chapter 3) 9.2 Construction Types and Height/Area Limitations (IBC Chapters 5 & 6) 9.3 Fire and Smoke Protection Features (IBC Chapters 7 & 8) 9.4 Fire Protection Systems (IBC Chapter 9) 9.5 Means of Egress and Occupant Load (IBC Chapter 10)
11 Chapter 10: Structural Plan Review
10.1 Design Loads and Structural Criteria (IBC Chapter 16) 10.2 Materials Standards and Foundations (IBC Chapters 18-23)
12 Chapter 11: Building Systems and Energy Code Plan Review
11.1 Mechanical (IMC) and Fuel Gas (IFGC) Plan Review 11.2 Plumbing Systems (IPC) and Backflow Protection 11.3 Electrical (NEC/NFPA 70) and Energy (IECC) Code Plan Review
13 Chapter 12: Field Inspection and Construction Compliance
12.1 Accessibility Standards and ANSI A117.1 Compliance 12.2 Soil Conditions, Excavation, and Site Inspections 12.3 Footing and Foundation Inspections 12.4 Concrete, Masonry, Steel, and Wood Structural Inspections 12.5 Rough-in MEP Inspections 12.6 Special Inspections and Quality Assurance (IBC Chapter 17) 12.7 Existing Buildings, Alterations (IEBC), and Final Inspections
9.3 Fire and Smoke Protection Features (IBC Chapters 7 & 8)
Key Takeaways Explain This Topic AI
Fire walls provide structural independence, separating buildings for height/area, while fire barriers and partitions restrict lateral or vertical fire spread.
Smoke barriers are 1-hour rated assemblies designed to limit smoke movement and create safe smoke compartments, essential for defend-in-place strategies.
Fire door and window opening protective ratings are directly tied to the wall rating in which they are installed (e.g., 2-hour walls require 1.5-hour doors).
Penetrations require firestopping systems evaluated for F-ratings (flame passage time) and T-ratings (temperature transmission limits).
Interior finish materials are classified as Class A, B, or C based on Flame Spread Index and Smoke-Developed Index under the Steiner Tunnel Test (ASTM E84).
Last updated: July 2026
- Fire and Smoke Protection Features (IBC Chapters 7 & 8)
- Principles of Passive Fire Protection
Passive fire protection relies on the design and construction of the building to contain fire, heat, and smoke within compartmentalized zones. Unlike active fire protection systems (such as sprinklers and alarms), passive protection does not require mechanical or electrical activation. IBC Chapter 7 establishes the requirements for fire-resistance-rated assemblies, including walls, floors, and roofs, and governs how openings (doors, windows, dampers) and penetrations (pipes, conduits, ducts) must be protected to prevent fire spread. Chapter 8 regulates the flame-spread and smoke-development characteristics of interior finishes, ensuring that the finish materials themselves do not contribute to rapid fire growth.
Types of Fire-Resistance-Rated Assemblies
IBC Chapter 7 distinguishes between several types of fire-rated walls based on their function, structural characteristics, and required continuity.
1. Fire Walls (IBC Section 706)
A fire wall is a fire-resistance-rated wall that divides a building into separate, independent structures for the purpose of calculating allowable height and area. A fire wall must meet the following criteria:
Structural Independence : The wall must have sufficient structural stability to remain standing even if the construction on one side completely collapses due to a fire.
Continuity : It must extend continuously from the foundation through the roof (unless a horizontal assembly of equivalent rating is used).
Fire Rating : Typically has a 2-hour, 3-hour, or 4-hour fire-resistance rating, depending on the occupancies present in the adjacent building portions.
Parapets : Must extend at least 30 inches above the roof to prevent fire from jumping over the top, unless specific noncombustible roof construction exemptions are met.
2. Fire Barriers (IBC Section 707)
A fire barrier is a fire-resistance-rated wall assembly designed to restrict the spread of fire. Unlike fire walls, fire barriers do not require structural independence. They are used for:
Enclosing shafts (such as elevator shafts and stairwells).
Separating exit enclosures (exit stairs, exit passageways).
Separating different occupancies in a separated mixed occupancy design.
Fire barriers must be continuous from the top of the floor assembly below to the underside of the floor or roof slab or deck above. They cannot terminate at a suspended ceiling.
3. Fire Partitions (IBC Section 708)
A fire partition is a lower-rated wall assembly designed to restrict the lateral spread of fire. Fire partitions are typically used for:
Separating dwelling units in Group R-2 (apartments, condos).
Separating sleeping units in Group R-1 (hotel rooms).
Corridor walls serving as part of the means of egress.
Fire partitions usually require a 1-hour fire-resistance rating. However, if the building is equipped with an automatic sprinkler system, the rating of corridor walls can often be reduced to 0.5 hours or even 0 hours. Fire partitions must extend from the floor assembly below to the underside of a rated ceiling or the deck above.
4. Smoke Barriers (IBC Section 709) and Smoke Partitions (IBC Section 710)
Smoke Barriers : Continuous membrane assemblies designed to restrict the movement of smoke. They must have a minimum fire-resistance rating of 1 hour (with some exceptions) and are used to divide large floors into smoke compartments. This is highly critical in Group I-2 (hospitals and nursing homes) to support a "defend-in-place" strategy.
Smoke Partitions : Designed to limit the transfer of smoke but do not require a fire-resistance rating. They are used to separate common areas from sleeping rooms in care facilities.
Opening Protectives: Doors, Windows, and Dampers
When a fire-rated wall is breached by doors, windows, or utilities, the opening must be protected to maintain the integrity of the barrier.
Fire Door and Window Assemblies (IBC Section 716)
The fire protection rating of doors and windows is determined by testing under NFPA 252 (for doors) and NFPA 257 (for windows). The required rating of the protective assembly is always tied to the rating of the wall in which it is installed, as shown in Table 716.1(2):
3-Hour Fire Wall : Requires a 3-hour or 1.5-hour fire door assembly depending on whether it is a high-hazard area.
2-Hour Fire Barrier : Requires a 1.5-hour (90-minute) fire door assembly.
1-Hour Fire Barrier (Shaft/Exit) : Requires a 1-hour (60-minute) fire door assembly.
1-Hour Fire Partition (Corridor) : Requires a 20-minute (0.33-hour) smoke-and-draft control door.
1-Hour Fire Partition (Tenant Separation) : Requires a 45-minute (0.75-hour) fire door.
Fire and Smoke Dampers (IBC Section 717)
Ducts that penetrate fire-resistance-rated walls or smoke barriers must be protected with automatic dampers:
Fire Dampers : Close upon high temperature detection (usually a fusible link) to prevent flame passage (tested to UL 555).
Smoke Dampers : Close upon smoke detection to prevent the spread of toxic gases (tested to UL 555S).
Combination Dampers : Perform both functions.
- Penetrations and Joint Systems
- Penetrations (IBC Section 714)
When pipes, conduits, or cables pass through a fire-rated assembly, they must be protected with an approved firestop system.
Through-Penetrations : Penetrate both sides of a wall or floor. They must be sealed with a system that has an F-rating (hours the system prevents flame passage) and a T-rating (hours the system limits temperature rise on the non-fire side, critical for floor/ceiling assemblies).
Membrane Penetrations : Penetrate only one side of an assembly (e.g., an electrical outlet box). These must be protected with firestop sealants, putty pads, or meet specific size and spacing exemptions (such as steel boxes not exceeding 16 square inches).
Joint Systems (IBC Section 715)
Joints (gaps between rated assemblies, such as expansion joints, or the head-of-wall joint where a wall meets a floor/roof deck) must be sealed using a joint system tested to UL 2079. The joint system must accommodate the thermal and structural movement of the building while maintaining the fire rating.
Interior Finishes (IBC Chapter 8)
The materials applied to the interior walls, ceilings, and floors can accelerate fire growth. The code regulates these materials based on their flame spread and smoke development.
ASTM E84 / UL 723 Steiner Tunnel Test
Interior wall and ceiling finishes are tested using the Steiner Tunnel Test, which compares the material’s burning characteristics against red oak (index of 100) and fiber-cement board (index of 0). The test yields two scores: the Flame Spread Index (FSI) and the Smoke-Developed Index (SDI).
Flame Spread Classifications (IBC Section 803.1.2)
Class A : Flame Spread Index 0–25; Smoke-Developed Index 0–450.
Class B : Flame Spread Index 26–75; Smoke-Developed Index 0–450.
Class C : Flame Spread Index 76–200; Smoke-Developed Index 0–450.
Note
The Smoke-Developed Index limit is always 450 for all classes.
Application of Finishes
The code restricts the use of these classes depending on the location within the building:
Exit Enclosures (Stairways) : Require the most restrictive finish (Class A in most occupancies).
Corridors : Usually require Class A or Class B.
General Rooms : Typically permit Class C.
If a building is equipped with an automatic sprinkler system, the code often permits a one-class reduction (e.g., allowing Class B instead of Class A, or Class C instead of Class B) due to the active suppression capability.