Study guide

2.3 Conductors (0103)

ICC Commercial Electrical Inspector E2

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Exam Format, Scheduling & Logistics 1.3 Study Strategy & Timeline 1.4 NEC Navigation & Open-Book Tactics

2 General Requirements (Domain 01 — 10%)

2.1 Project Administration & Legal (0101) 2.2 Public Information: Terminology, Listing & Labeling (0102) 2.3 Conductors (0103) 2.4 Conductor Ampacity & Termination Workshop (0103)

3 Services (NEC Article 230 & 250)

3.1 Service Size, Rating & Installations (0201) 3.2 Service & Feeder Grounding & Bonding (0202) 3.3 Service Calculations, Clearances & Working Space (depth) 3.4 Service Conductor Installation, Raceways & Emergency Disconnects (0201) 3.5 Grounding Electrode Conductor Installation & Connections (0202) 3.6 Bonding of Metal Piping, Building Steel & Separately Derived Systems (0202)

4 Branch Circuits & Feeders (NEC Articles 210, 215, 220, 240)

4.1 Branch Circuit & Feeder Installation (0301) 4.2 Branch Circuit & Feeder Calculations (0302) 4.3 Branch Circuit Ratings & Overcurrent Protection (0303) 4.4 Equipment Grounding & Bonding (0304) 4.5 Feeder Installation & Buildings Supplied by a Feeder (0301) 4.6 Non-Dwelling Load Calculation Workshop (0302) 4.7 Transformer Secondary Conductors & Selective Coordination (0303) 4.8 Equipment Grounding Conductor Installation & Fault-Path Verification (0304)

5 Wiring Methods & Distribution Systems (NEC Chapters 3 & 4)

5.1 Branch Circuit Required Outlets (0401) 5.2 Boxes, Enclosures & Conduit Bodies (0402) 5.3 Panelboards & Switchboards (0403) 5.4 Raceways, Cables & Bus Ducts (0404) 5.5 Flexible Cords & Fixture Wires (0405) 5.6 Pull Boxes, Cabinets, Cutout Boxes & Accessibility (0402) 5.7 Panelboard Arrangement, Back-Fed Devices & Switchgear Inspection (0403) 5.8 Underground Raceways, Cover Depths & Cable Trays (0404)

6 General Use Equipment (NEC Chapter 4)

6.1 Switches, Receptacles & Light Fixtures (0501) 6.2 General Use Equipment & Appliances (0502) 6.3 Motors & Controllers (0503) 6.4 Transformers, Generators & Misc Equipment (0504)

7 Special Occupancies (NEC Chapter 5)

7.1 Hazardous Locations (0601) 7.2 Health Care Facilities (0602) 7.3 Miscellaneous Other Special Occupancies (0603) 7.4 Commercial Garages, Gas Stations & Bulk Stations (0604)

8 Special Equipment (NEC Chapter 6)

8.1 Swimming Pools, Fountains & Similar Installations (0701) 8.2 Miscellaneous Special Equipment (0702) 8.3 Pool Bonding, Underwater Luminaires & Spa Inspection Workshop (0701)

9 Special Systems (NEC Chapters 7 & 8)

9.1 Emergency Systems (0801) 9.2 Signaling Systems (0802) 9.3 Fire Alarm Systems (0803) 9.4 Communications Systems (0804)

2.3 Conductors (0103)

Key Takeaways Explain This Topic AI

Conductor ampacity is read from Table 310.16, but the ampacity usable at a termination is limited by 110.14(C) to the 60°C or 75°C column based on the equipment rating and marking — a 90°C THHN conductor is still sized on the 75°C column at most equipment rated over 100 A.

When more than three current-carrying conductors share a raceway, apply the adjustment factors of 310.15(C)(1); when the ambient is not 30°C, apply the correction factors of 310.15(B)(1). Both are applied to the ampacity column matching the conductor insulation, then compared to the 110.14(C) termination limit.

Paralleling is permitted for conductors 1/0 AWG and larger under 310.10(G); every conductor of a parallel set must be the same length, material, size, and insulation type, and be terminated in the same manner.

Conductor splices and terminations must be made in a box or conduit body (300.15), connections must comply with 110.14(B), and marked torque values must be applied with a calibrated torque tool (110.14(D)).

The small-conductor rule in 240.4(D) caps overcurrent protection at 15 A for 14 AWG Cu, 20 A for 12 AWG Cu, and 30 A for 10 AWG Cu, regardless of the higher figures in the 75°C and 90°C columns.

Last updated: August 2026

Conductor Types and Insulation Letter Designations

Conductors are identified by a letter designation that encodes insulation material, temperature rating, and location suitability. Table 310.4(A) is the master list of conductor insulations rated 600 volts, giving each type's trade name, maximum operating temperature, and permitted application. Common types:

  • Letter Trade Name Max Temp Typical Application
  • THHN High heat-resistant thermoplastic nylon 90°C dry/damp Branch circuits, general wiring
  • THWN Heat- and moisture-resistant thermoplastic nylon 75°C wet / 90°C dry Wet locations, conduit
  • THWN-2 Same as THWN, 90°C wet and dry 90°C all locations General purpose, wet/damp
  • XHHW Cross-linked synthetic polymer (XLPE) 75°C wet / 90°C dry Dry/wet, industrial
  • XHHW-2 XLPE, 90°C all 90°C all locations General, wet/damp, direct burial
  • THW / THW-2 Thermoplastic, moisture- and heat-resistant 75°C / 90°C Dry and wet
  • TW Moisture-resistant thermoplastic 60°C Dry and wet, general
  • USE-2 Underground service entrance (XLPE) 90°C Direct burial, no indoor use

The suffix "-2" means the conductor is rated 90°C in wet locations (not just dry). When the inspector sees THWN-2 or XHHW-2, the 90°C column may be used for derating calculations.

Copper vs. Aluminum

Copper (Cu) — lower resistance; smaller size for a given ampacity. Read the copper columns of Table 310.16.

Aluminum (Al) and copper-clad aluminum (CCA) — lighter and cheaper for large feeders; read the aluminum/copper-clad aluminum columns of Table 310.16, which run roughly two AWG sizes larger than copper for the same ampacity. Aluminum and copper-clad aluminum 1/0 AWG and larger may be paralleled under 310.10(G), the same threshold as copper.

Ampacity — Table 310.16

Table 310.16 gives allowable ampacities for insulated conductors rated 0–2000 V, not more than 3 current-carrying conductors in a raceway/cable/earth, and an ambient temperature of 30°C. Excerpt (copper):

  • Size (Cu) 60°C 75°C 90°C
  • 14 AWG 15 A 20 A 25 A
  • 12 AWG 20 A 25 A 30 A
  • 10 AWG 30 A 35 A 40 A
  • 8 AWG 40 A 50 A 55 A
  • 6 AWG 55 A 65 A 75 A
  • 4 AWG 70 A 85 A 95 A
  • 3 AWG 85 A 100 A 115 A
  • 2 AWG 95 A 115 A 130 A
  • 1 AWG 110 A 130 A 150 A
  • 1/0 AWG 125 A 150 A 170 A
  • 2/0 AWG 145 A 175 A 195 A
  • 3/0 AWG 165 A 200 A 225 A
  • 4/0 AWG 195 A 230 A 260 A

The 240.4(D) small-conductor rule caps the overcurrent protection for 14 AWG Cu at 15 A, 12 AWG Cu at 20 A, and 10 AWG Cu at 30 A, regardless of the higher numbers in the 75°C/90°C columns (with exceptions listed in 240.4(G)).

Termination Temperature Limits — 110.14(C)

The conductor's insulation may be rated 90°C, but terminations are limited by 110.14(C) :

Equipment rated 100 A or less , or marked for conductors 14 AWG through 1 AWG: use the 60°C column unless the equipment is marked 60/75°C , in which case the 75°C column is permitted.

Equipment rated over 100 A , or marked for conductors larger than 1 AWG: use the 75°C column unless marked for 90°C.

A conductor with higher-rated insulation (e.g., 90°C THHN) may be used, but the ampacity at the termination is taken from the termination-rated column. The 90°C column is the starting point only for derating (correction/adjustment).

The Practical Rule

Size the conductor at the termination using 110.14(C) (usually the 75°C column).

Size the conductor in the raceway for derating using the 90°C column (if the insulation is 90°C).

The smaller of the two is the final ampacity.

Derating (Correction and Adjustment Factors) — 310.15

Table 310.16 is built on two stated conditions: an ambient of 30°C (86°F) and not more than three current-carrying conductors in the raceway, cable, or earth. When the installation departs from either condition, apply the factors printed with Article 310:

Ambient temperature correction — Table 310.15(B)(1): multiply the ampacity from the column matching the conductor insulation by the correction factor for the actual ambient. Representative factors (90°C column):

  • 31–35°C: 0.96
  • 36–40°C: 0.91
  • 41–45°C: 0.87
  • 46–50°C: 0.82

Adjustment for more than three current-carrying conductors — 310.15(C)(1):

  • 4–6 CCC: 80%
  • 7–9 CCC: 70%
  • 10–20 CCC: 50%
  • 21–30 CCC: 45%
  • Worked Example

A feeder is run with 6 current-carrying conductors of #2 AWG THHN copper in a single conduit, in a mechanical room where the ambient is 40°C .

Base ampacity from Table 310.16, 90°C column (THHN is 90°C): 130 A .

Ambient correction at 40°C, 90°C column (Table 310.15(B)(1)): 0.91 .

130 × 0.91 = 118.3 A .

Adjustment for 6 CCC (310.15(C)(1)): 0.80 .

118.3 × 0.80 = 94.6 A .

Termination limit — #2 AWG Cu at 75°C (equipment >100 A, 110.14(C)) = 115 A .

The derated value (94.6 A) is less than the termination limit (115 A), so the derated ampacity governs: ~94 A .

If this conductor served a continuous load, the OCPD would be sized at 125% of the continuous load per 215.3 and must not exceed 94 A.

Conductor Connections, Splices, and Terminal Identification

110.14(B) — Splices: conductor splices and joints must be made with listed splicing devices or by brazing, welding, or soldering with a fusible metal or alloy — and a soldered splice must first be mechanically and electrically secure without the solder , then soldered. Splices must be made in a box or conduit body.

300.15 — Boxes and conduit bodies required: A box or conduit body must be installed at each conductor splice, tap, termination, or junction point, and must remain accessible (314.29).

110.14(D) — Terminal connection torque: where a tightening torque is indicated as a numeric value on equipment or in the installation instructions, it must be applied with a calibrated torque tool (torque wrench, screwdriver, or driver).

Terminal identification: Terminals must be marked to indicate the conductor material (Cu/Al/Cu-Al) they are listed for. Aluminum-rated terminals used with aluminum conductors must be listed and installed with antioxidant compound if required.

Paralleling — 310.10(G)

Paralleling means using two or more conductors per phase instead of one large conductor. Under 310.10(G) :

Allowed for 1/0 AWG and larger copper, aluminum, and copper-clad aluminum.

Every conductor of a given parallel set (all the phase A conductors, all the phase B conductors, and so on) must be the same length, same conductor material, same circular-mil area, and same insulation type , and must be terminated in the same manner .

Where the parallel sets are run in separate raceways or cables , each raceway or cable must have the same number of conductors and the same electrical characteristics , so that current divides evenly. All conductors of the same circuit — every phase, the neutral, and the equipment grounding conductor — must be in each raceway (300.3(B)); putting all the phase A conductors in one steel conduit is an inductive-heating violation, and it is a classic exam trap.

The equipment grounding conductor in each parallel raceway is full-size per Table 250.122 for the circuit overcurrent device, not divided among the raceways.

Paralleling is common on large commercial feeders and services; the inspector verifies that each conductor in a set is identical and that sets are distributed across phases to avoid inductive heating.