Study guide
2.3 Hangers, Support, and Sizing Fundamentals
ICC Commercial Plumbing Inspector P2
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: General Requirements
1.1 Scope, Administration, and Enforcement 1.2 General Plumbing Regulations
2 Chapter 2: Piping Protection & Installation
2.1 Piping Protection 2.2 Piping Installation and Joint Connections 2.3 Hangers, Support, and Sizing Fundamentals
3 Chapter 3: Fixtures, Faucets, and Fixture Fittings
3.1 Minimum Fixture Counts and Clearance Requirements 3.2 Accessible Fixtures and Controls 3.3 Water Conservation, Faucets, and Fittings
4 Chapter 4: Water Heaters
4.1 Sizing and Installation Requirements 4.2 Safety Devices and T&P Relief Valves 4.3 Water Heater Venting and Combustion Air
5 Chapter 5: Water Supply and Distribution
5.1 Potable Water Sizing and Demands 5.2 Cross-Connection Control and Backflow Prevention 5.3 Water Service and Distribution Materials & Joints 5.4 Hot Water Systems and Recirculation
6 Chapter 6: Sanitary Drainage Systems
6.1 Drainage Fixture Units (DFUs) and Sizing 6.2 Drainage Piping Installation and Slopes 6.3 Cleanouts and Building Sewers 6.4 Sumps, Ejectors, and Backwater Valves
7 Chapter 7: Venting Systems
7.1 Venting Methods and Materials 7.2 Vent Sizing and Developed Length 7.3 Circuit Venting 7.4 Combination Waste & Vent Systems and Air Admittance Valves
8 Chapter 8: Traps, Interceptors, and Separators
8.1 Trap Design and Installation 8.2 Interceptors and Separators 8.3 Special Waste and Chemical Neutralization Systems
9 Chapter 9: Storm Drainage Systems
9.1 Storm Drainage Sizing 9.2 Roof Drains and Conductors 9.3 Subsoil Drainage and Sump Pumps
10 Chapter 10: Special Piping & Gas Piping
10.1 Fuel Gas Piping Installation 10.2 Medical Gas and Nonflammable Gas Systems 10.3 Nonpotable Water Systems and Graywater Storage
2.3 Hangers, Support, and Sizing Fundamentals
Key Takeaways Explain This Topic AI
Copper tubing 1-1/4 inches and smaller must be supported horizontally every 6 feet, while larger sizes allow 10-foot spacing (IPC Table 308.5).
PVC and ABS DWV piping must be supported horizontally every 4 feet and vertically every 10 feet with mid-story guides (IPC Table 308.5).
PEX tubing horizontal supports must be spaced no more than 32 inches apart, while vertical stacks require supports every 10 feet (IPC Table 308.5).
Cast-iron piping horizontal supports must be spaced every 5 feet (or 10 feet for 10-foot pipe lengths) and at every joint (IPC Table 308.5).
Horizontal drainage piping must slope at least 1/4 inch per foot for diameters 2-1/2 inches and smaller, and 1/8 inch per foot for 3 to 6 inches (IPC Table 704.1).
Last updated: July 2026
General Support Principles (IPC Section 308)
Plumbing systems are subject to significant dead loads (the weight of the pipe and the water it carries) and dynamic forces (water hammer, thermal expansion, structural deflection). Proper hanger design and support spacing prevent sagging, maintain correct slope, and prevent joint stress that leads to premature failure.
Hanger Material Compatibility (IPC Section 308.3)
Hangers and strapping must be made of materials that are compatible with the piping they support.
Galvanic Protection: Supporting copper pipe with bare steel hangers creates a galvanic cell, resulting in rapid corrosion of the steel and pipe leakage. Copper pipe must be supported by copper-plated hangers, copper straps, or hangers with non-conductive plastic inserts.
Plastic Piping Protection: Hangers for plastic pipes (PVC, ABS, PEX) must have broad, smooth bearing surfaces. Thin wire hangers or sharp metal straps can cut into the plastic over time due to thermal movement.
Spacing of Hangers (IPC Table 308.5)
Hanger spacing is determined by the piping material's rigidity, diameter, and whether the run is horizontal or vertical. Rigid metal pipes require fewer supports than flexible plastic tubing.
Horizontal and Vertical Spacing Requirements
Plumbing inspectors must memorize or reference the maximum allowable spacing for common materials:
Copper or Copper-Alloy Tubing:
1-1/4 inches and smaller: Horizontal spacing must not exceed 6 feet (1829 mm) .
1-1/2 inches and larger: Horizontal spacing must not exceed 10 feet (3048 mm) .
Vertical stacks: Must be supported at least every 10 feet (3048 mm) (typically at each floor level).
Copper or Copper-Alloy Pipe (Hard-Drawn):
Horizontal spacing is allowed up to 12 feet (3658 mm) .
Vertical support must be provided at least every 10 feet (3048 mm) .
Steel Pipe (Threaded or Welded):
Horizontal spacing must not exceed 12 feet (3658 mm) .
Vertical stacks must be supported at least every 15 feet (4572 mm) .
Cast-Iron Pipe:
Horizontal spacing is limited to 5 feet (1524 mm) .
Exception: If 10-foot lengths of pipe are used, hangers can be spaced at 10-foot (3048 mm) intervals, provided support is located at each joint and fitting.
Vertical stacks must be supported at least every 15 feet (4572 mm) .
PVC and ABS DWV Piping:
Horizontal spacing must not exceed 4 feet (1219 mm) .
Vertical stacks must be supported at least every 10 feet (3048 mm) , and mid-story guides must be installed to prevent bowing and lateral deflection.
PEX Tubing:
Horizontal spacing is limited to 32 inches (813 mm) (approx. 2.67 feet) to prevent sagging between hangers.
Vertical support must be provided at least every 10 feet (3048 mm) , with mid-story guides.
CPVC Piping:
1 inch and smaller: Horizontal spacing is limited to 3 feet (914 mm) .
1-1/4 inches and larger: Horizontal spacing is limited to 4 feet (1219 mm) .
Vertical support must be provided at least every 10 feet (3048 mm) .
Thermal Expansion and Movement (IPC Section 308.2)
All piping materials expand and contract with temperature changes. This is particularly critical in hot water supply lines and plastic systems.
Expansion Rates: Plastic piping expands at a much higher rate than metal.
PEX expands approximately 1.1 inches per 10 feet of pipe for every 100°F temperature rise.
PVC expands approximately 3.6 inches per 100 feet of pipe per 100°F temperature rise.
Copper expands about 1.1 inches per 100 feet per 100°F temperature rise.
Provisions for Movement: Pipes must not be anchored rigidly. The system must utilize expansion loops, offsets, or mechanical expansion joints.
Sleeves: Sleeves at structural penetrations must be large enough to allow the pipe to slide during expansion cycles.
Sizing and Slope of Horizontal Drainage Piping (IPC Section 704 & Table 704.1)
Proper drainage requires gravimetric flow. The slope of horizontal drainage piping must be uniform and based on the pipe diameter.
Sizing and Slope Requirements:
2-1/2 inches and smaller: Minimum slope is 1/4 inch per foot (2% slope) .
3 inches to 6 inches: Minimum slope is 1/8 inch per foot (1% slope) .
8 inches and larger: Minimum slope is 1/16 inch per foot (0.5% slope) .
The Velocity Principle:
The goal is to maintain a flow velocity of at least 2 feet per second (fps) . This velocity is self-cleansing, carrying solid wastes along with the liquid.
If the slope is too flat, solids settle and block the pipe.
If the slope is too steep, liquid may run faster than solids, leaving the solids behind to accumulate and cause blockages.
Inspector Field Checklist & Sizing Tips
PEX Sagging: PEX is highly flexible. While the code permits 32-inch spacing, contractors often exceed this, causing the pipe to sag and trap air or sediment. Ensure hangers do not pinch the PEX, allowing it to slide freely during thermal expansion.
Slope and Flow: If a 4-inch sewer is installed at a 1/2 inch per foot slope (excessive slope), the water can run ahead of solid waste, leaving feces and paper to dry and cause blockages. Conversely, a slope less than 1/8 inch per foot for a 3-inch pipe will result in sluggish flow. Always check the slope with a digital level.
Mid-Story Guides: For vertical PVC/ABS stacks, mid-story guides are critical. Without them, thermal expansion will cause the vertical pipe to bow, putting stress on branch connections.
Synthesis of Support and Sizing Requirements
- Piping Material Max Horizontal Spacing Max Vertical Spacing Minimum Slope (By Diameter)
- Copper Tubing (≤ 1-1/4") 6 feet 10 feet N/A (Water Distribution)
- Copper Tubing (≥ 1-1/2") 10 feet 10 feet N/A (Water Distribution)
- Copper Pipe (Hard) 12 feet 10 feet N/A (Water Distribution)
- Steel Pipe 12 feet 15 feet N/A
- Cast-Iron 5 feet (or 10 feet*) 15 feet 1/4" per ft (≤2.5"), 1/8" (3-6")
- PVC / ABS DWV 4 feet 10 feet (with guides) 1/4" per ft (≤2.5"), 1/8" (3-6")
- PEX Tubing 32 inches 10 feet (with guides) N/A (Water Distribution)
- CPVC (≤ 1") 3 feet 10 feet (with guides) N/A (Water Distribution)
- CPVC (≥ 1-1/4") 4 feet 10 feet (with guides) N/A (Water Distribution)