Study guide

6.1 Drainage Fixture Units (DFUs) and Sizing

ICC Commercial Plumbing Inspector P2

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: General Requirements

1.1 Scope, Administration, and Enforcement 1.2 General Plumbing Regulations

2 Chapter 2: Piping Protection & Installation

2.1 Piping Protection 2.2 Piping Installation and Joint Connections 2.3 Hangers, Support, and Sizing Fundamentals

3 Chapter 3: Fixtures, Faucets, and Fixture Fittings

3.1 Minimum Fixture Counts and Clearance Requirements 3.2 Accessible Fixtures and Controls 3.3 Water Conservation, Faucets, and Fittings

4 Chapter 4: Water Heaters

4.1 Sizing and Installation Requirements 4.2 Safety Devices and T&P Relief Valves 4.3 Water Heater Venting and Combustion Air

5 Chapter 5: Water Supply and Distribution

5.1 Potable Water Sizing and Demands 5.2 Cross-Connection Control and Backflow Prevention 5.3 Water Service and Distribution Materials & Joints 5.4 Hot Water Systems and Recirculation

6 Chapter 6: Sanitary Drainage Systems

6.1 Drainage Fixture Units (DFUs) and Sizing 6.2 Drainage Piping Installation and Slopes 6.3 Cleanouts and Building Sewers 6.4 Sumps, Ejectors, and Backwater Valves

7 Chapter 7: Venting Systems

7.1 Venting Methods and Materials 7.2 Vent Sizing and Developed Length 7.3 Circuit Venting 7.4 Combination Waste & Vent Systems and Air Admittance Valves

8 Chapter 8: Traps, Interceptors, and Separators

8.1 Trap Design and Installation 8.2 Interceptors and Separators 8.3 Special Waste and Chemical Neutralization Systems

9 Chapter 9: Storm Drainage Systems

9.1 Storm Drainage Sizing 9.2 Roof Drains and Conductors 9.3 Subsoil Drainage and Sump Pumps

10 Chapter 10: Special Piping & Gas Piping

10.1 Fuel Gas Piping Installation 10.2 Medical Gas and Nonflammable Gas Systems 10.3 Nonpotable Water Systems and Graywater Storage

6.1 Drainage Fixture Units (DFUs) and Sizing

Key Takeaways Explain This Topic AI

Drainage Fixture Units (DFUs) are relative factors from IPC Table 709.1 representing the load-producing effect of fixtures on the drainage system.

A public water closet flushing at 1.6 gpf is assigned 4 DFUs, while one flushing at more than 1.6 gpf is assigned 6 DFUs.

A 3-inch horizontal branch can carry a maximum of 20 DFUs and is strictly limited to serving a maximum of 2 water closets.

A 4-inch building drain or sewer at a 1/4 inch per foot slope has a maximum capacity of 216 DFUs per IPC Table 710.1(1).

A 3-inch stack with 3 branch intervals or fewer can carry up to 48 DFUs and a maximum of 6 water closets total.

Last updated: July 2026

Sizing Sanitary Drainage Systems with DFUs

To ensure that sanitary drainage systems operate efficiently under gravity flow, the International Plumbing Code (IPC) uses the Drainage Fixture Unit (DFU) method. A DFU is a relative load factor that represents the waste-producing effect of a plumbing fixture. It accounts for flow rate, discharge duration, and the average time between operations. Sizing based on DFUs prevents hydraulic overload, which can fill drainage pipes completely, disrupt pneumatic pressure, and siphon fixture trap seals.

Fixture DFU Values (IPC Table 709.1)

Fixture values are divided based on their application: private (residential dwellings, private hotel bathrooms) and public (offices, schools, commercial spaces, public restrooms). For the ICC P2 exam, memorizing key commercial DFU values is essential.

  • Plumbing Fixture Flush/Flow Rate Private Use (DFU) Public Use (DFU)
  • Water Closet (Toilet) ≤ 1.6 \le 1.6 ≤ 1.6 gallons per flush (gpf) 3 4
  • Water Closet (Toilet) > 1.6 gallons per flush (gpf) 4 6
  • Urinal Pedestal or Wall-hung — 2
  • Lavatory (Sink) Standard 1 1
  • Kitchen Sink Commercial or Domestic 2 2
  • Service Sink (Slop) Standard — 3
  • Floor Drain 2-inch — 2
  • Floor Drain 3-inch — 3
  • Floor Drain 4-inch — 4
  • Shower Single shower head 2 3
  • Drinking Fountain Standard — 0.5 (1/2)

Important

Exam Tip: Pay close attention to water closet flush rates. A standard commercial water closet flushing at 1.6 gpf carries 4 DFUs . A high-volume or older water closet flushing at greater than 1.6 gpf carries 6 DFUs . This difference changes sizing calculations dramatically.

Sizing Building Drains and Sewers (IPC Table 710.1(1))

The building drain is the lowest horizontal piping of a drainage system inside the building that conveys waste to the building sewer , which begins 5 feet (1524 mm) outside the foundation wall. Building drains and sewers are sized based on the total DFU load and the slope (pitch) of the pipe.

To prevent solids from settling, the flow must maintain a self-cleansing velocity of at least 2 feet per second (fps) . Smaller pipes require steeper slopes to overcome friction. Below is a summary of the maximum DFU capacities for building drains and sewers:

  • Pipe Size (inches) 1/16 in/ft Slope 1/8 in/ft Slope 1/4 in/ft Slope 1/2 in/ft Slope
  • 1-1/2 — — 3 3
  • 2 — — 21 26
  • 2-1/2 — — 24 31
  • 3 — 36 42 50
  • 4 — 180 216 250
  • 5 — 390 480 575
  • 6 — 700 840 1,000
  • 8 1,400 1,600 1,920 2,300
  • Sizing Horizontal Branches and Stacks (IPC Table 710.1(2))

Horizontal branches connect fixtures on a single floor to a vertical stack. Stacks carry waste vertically to the building drain. Sizing these elements involves matching the cumulative DFU load against Table 710.1(2) while adhering to strict physical fixture limits.

The 3-Inch Water Closet Limit:

A 3-inch horizontal branch is permitted to carry a maximum of 20 DFUs . However, it is restricted to a maximum of 2 water closets . If a branch serves 3 or more water closets, the pipe size must be increased to 4 inches, regardless of whether the total DFU load is under 20.

Stack Sizing Limits:

A 3-inch stack with 3 branch intervals or fewer is permitted to carry up to 48 DFUs .

A 3-inch stack with more than 3 branch intervals is permitted to carry up to 72 DFUs .

No more than 2 water closets can connect to any single branch interval of a 3-inch stack, and the entire 3-inch stack is limited to a maximum of 6 water closets .

The diameter of the drainage piping must never decrease in the direction of flow. If a 4-inch branch connects to a stack, the stack must be at least 4 inches.

  • Worked Sizing Examples
  • Example 1: Sizing a Horizontal Branch for a Commercial Restroom Battery

A commercial restroom battery consists of:

  • 4 Public Water Closets (1.6 gpf)
  • 2 Public Urinals
  • 3 Public Lavatories
  • Step 1: Calculate Total DFU Load
  • 4 public water closets: 4 WCs × \times × 4 DFUs = 16 DFUs
  • 2 public urinals: 2 urinals × \times × 2 DFUs = 4 DFUs
  • 3 public lavatories: 3 lavatories × \times × 1 DFU = 3 DFUs
  • Total DFU Load = 16 + 4 + 3 = 23 DFUs
  • Step 2: Size the Branch

Looking at Table 710.1(2), a 3-inch horizontal branch can carry up to 20 DFUs. Since our load is 23 DFUs, a 3-inch pipe is hydraulically undersized.

Furthermore, we have 4 water closets . A 3-inch branch has a strict limit of 2 water closets .

Therefore, we must use a 4-inch horizontal branch (which carries up to 160 DFUs and has no water closet limit).

Step 3: Size the Building Drain at 1/4 in/ft slope

The total load is 23 DFUs. According to Table 710.1(1), a 3-inch building drain at 1/4 in/ft slope is rated for up to 42 DFUs , so on capacity alone a 3-inch drain would carry the 23-DFU load.

However, because the horizontal branch entering the building drain is 4 inches , the no-decrease-in-direction-of-flow rule governs: the building drain cannot be smaller than the pipe feeding it.

Therefore, the building drain must also be 4 inches .

Loading diagram... Sanitary Drainage Sizing Decision Flowchart