Study guide
Section 3.2: Maximum Allowable Quantities and Control Areas
ICC Fire Plans Examiner F3
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: General Administration
Section 1.1: Code Authority and Administrative Procedures Section 1.2: Recordkeeping and Interagency Coordination
2 Chapter 2: Building Construction and Occupancy
Section 2.1: Occupancy Classification and Use Section 2.2: Construction Types and Height/Area Limits Section 2.3: Occupant Load Calculations Section 2.4: Special Fire Protection Features
3 Chapter 3: Hazardous Materials
Section 3.1: Material Classification and Inventory Section 3.2: Maximum Allowable Quantities and Control Areas Section 3.3: Storage, Use, and Handling General Requirements Section 3.4: Flammable and Combustible Liquids Section 3.5: Compressed Gases and Cryogenic Fluids Section 3.6: Special Hazards and Explosion Control
4 Chapter 4: Fire Protection Systems
Section 4.1: Fire Department Access and Hydrants Section 4.2: Water Supply and Fire Flow Calculations Section 4.3: Automatic Sprinkler Systems Section 4.4: Standpipe and Hose Systems Section 4.5: Fire Alarm and Detection Systems Section 4.6: Smoke Control and Venting Systems Section 4.7: Portable Fire Extinguishers and Special Suppression Systems
5 Chapter 5: Egress Safety
Section 5.1: Means of Egress Components and Design Section 5.2: Exit Access and Travel Distance Section 5.3: Number of Exits and Exit Configuration Section 5.4: Stairs, Handrails, and Ramps Section 5.5: Doors, Hardware, and Exit Signage Section 5.6: Emergency Lighting and Standby/Emergency Power
Section 3.2: Maximum Allowable Quantities and Control Areas
Key Takeaways Explain This Topic AI
The Maximum Allowable Quantity (MAQ) is the threshold of hazardous materials permitted in a control area before classification as Group H is required.
Table 5003.1.1(1) and Table 5003.1.1(2) outline MAQs based on hazard type and operational state (storage, closed use, open use).
MAQ limits can be increased by 100% for automatic sprinkler systems and another 100% for approved storage cabinets (cumulative up to 4x).
Control areas divide a building using rated fire barriers, with allowable MAQ percentages and number of areas decreasing on higher and lower floors.
Last updated: July 2026
Maximum Allowable Quantities and Control Areas (IFC 5003)
The central regulatory mechanism of hazardous materials control in the 2024 International Fire Code (IFC) is the Maximum Allowable Quantity (MAQ). The MAQ is the threshold of hazardous materials that can be present within a single control area before the space must be classified as a Group H (High-Hazard) occupancy. The MAQ concept balances the operational needs of businesses—such as laboratories, dry cleaners, manufacturing plants, and retail stores—with public safety. If a facility keeps its chemical quantities below the adjusted MAQ, it can operate under standard business (Group B), mercantile (Group M), or storage (Group S) regulations. Once those quantities are exceeded, the facility must comply with the stringent structural, separation, and active protection requirements of Group H.
Tables 5003.1.1(1) and 5003.1.1(2)
The baseline limits for hazardous materials are set forth in two primary tables:
IFC Table 5003.1.1(1) : Establishes MAQs for physical hazards, such as flammable liquids, combustible liquids, flammable gases, oxidizers, and pyrophorics.
IFC Table 5003.1.1(2) : Establishes MAQs for health hazards, specifically corrosives, toxics, and highly toxics.
These tables are structured around three operational states:
Storage : Materials in sealed containers, cylinders, or tanks. This represents static hazard conditions and has the highest allowable limits.
Closed Use : Materials used in a system that remains completely closed to the atmosphere during normal operations, such as chemicals pumped through a sealed piping system. Allowable quantities are generally equal to or slightly lower than storage limits.
Open Use : Materials exposed to the air during processing, mixing, or dispensing, such as blending solvents in an open vat. This represents the highest risk due to the release of flammable or toxic vapors, and has the lowest allowable quantities.
For example, under Table 5003.1.1(1), the baseline storage limit for Class IA flammable liquids is 30 gallons. The closed use limit is also 30 gallons, but the open use limit is restricted to 10 gallons.
Tabular Increases (Multipliers)
The quantities listed in Tables 5003.1.1(1) and 5003.1.1(2) are baseline limits. The code permits these limits to be increased if specific fire safety systems are installed. The two primary increases are:
Automatic Sprinkler System (NFPA 13) : If the building is equipped throughout with an automatic sprinkler system in accordance with Section 903.3.1.1, the allowable quantities of many materials are increased by 100 percent (multiplied by 2). Sprinklers cool the area, control fire spread, and prevent chemical containers from catastrophically failing.
Approved Cabinets or Gas Cabinets : If materials are stored inside approved safety cabinets (such as NFPA 30 cabinets for flammable liquids) or gas cabinets/exhausted enclosures, the allowable quantities are increased by 100 percent (multiplied by 2). Cabinets insulate the chemicals from thermal exposure, delaying involvement in a fire.
Cumulative Increases
These increases are cumulative and multiplicative. If a facility is sprinklered and uses safety cabinets, the adjusted MAQ is calculated as: Adjusted MAQ = Tabular MAQ × 2 (sprinkler increase) × 2 (cabinet increase) = Tabular MAQ × 4 \text{Adjusted MAQ} = \text{Tabular MAQ} \times 2 \text{ (sprinkler increase)} \times 2 \text{ (cabinet increase)} = \text{Tabular MAQ} \times 4 Adjusted MAQ = Tabular MAQ × 2 (sprinkler increase) × 2 (cabinet increase) = Tabular MAQ × 4
For instance, a Class IB flammable liquid has a baseline storage MAQ of 120 gallons. If it is stored in safety cabinets inside a sprinklered building, the adjusted limit is: 120 gallons × 2 × 2 = 480 gallons 120 \text{ gallons} \times 2 \times 2 = 480 \text{ gallons} 120 gallons × 2 × 2 = 480 gallons
Restrictions on Increases
The plans examiner must recognize that increases are not universally permitted. For example, open use of flammable liquids does not receive a cabinet increase. Some high-hazard materials, like explosives or Class 4 oxidizers, do not receive sprinkler or cabinet increases. Furthermore, highly toxic and toxic gases are required to be kept in gas cabinets as a baseline safety measure; therefore, the cabinet does not grant a 100% quantity increase, and the limit remains the baseline value.
Control Areas (IFC Section 5003.8.3)
A control area is a designated compartment within a building where hazardous materials are stored, used, or handled in quantities not exceeding the MAQ. Rather than classifying an entire building as a Group H occupancy, the designer can divide the building into multiple control areas separated by fire barriers or horizontal assemblies.
Table 5003.8.3.2 dictates the design and number of control areas permitted per floor, as well as the percentage of the baseline MAQ allowed in each control area. The allowed quantities decrease significantly on higher and lower floors:
First Floor (Grade Plane) : 100% of MAQ, maximum of 4 control areas, separated by 1-hour fire barriers.
Second Floor : 75% of MAQ, maximum of 3 control areas, separated by 1-hour fire barriers.
Third Floor : 50% of MAQ, maximum of 2 control areas, separated by 1-hour fire barriers.
Floors 4 through 6 : 12.5% of MAQ, maximum of 2 control areas, separated by 2-hour fire barriers.
Floors 7 through 9 : 5% of MAQ, maximum of 2 control areas, separated by 2-hour fire barriers.
Floors Higher Than 9 : 5% of MAQ, maximum of 1 control area, separated by 2-hour fire barriers.
Basement Level 1 : 75% of MAQ, maximum of 3 control areas, separated by 1-hour fire barriers.
Basement Level 2 : 50% of MAQ, maximum of 2 control areas, separated by 1-hour fire barriers.
Basement Level 3 and Lower : Hazardous materials storage and use are prohibited.
Rationale for Control Area Restrictions
The reduction in allowable quantities on upper floors and basements is a critical safety principle. As fire moves upward, smoke and heat accumulate on upper levels, complicating occupant evacuation and delaying fire department search and rescue. Firefighters must carry equipment up stairs, which slows response times. In basements, ventilation is restricted, and fire department access is poor, creating a severe trap hazard.
Mixed Occupancy and Group H Classifications
When the adjusted MAQ is exceeded within a control area, the space must be classified as a Group H (High-Hazard) occupancy. The plans examiner must verify the specific classification:
Group H-1 : Facilities containing materials that present a detonation hazard (e.g., explosives).
Group H-2 : Facilities containing materials that present a deflagration hazard or accelerated burning (e.g., flammable gases).
Group H-3 : Facilities containing materials that support combustion or present physical hazards that are not detonation or deflagration hazards (e.g., Class II combustible liquids, oxidizers).
Group H-4 : Facilities containing health hazards (e.g., toxic or corrosive gases).
Group H-5 : Semiconductor fabrication facilities.