Study guide
4.1 ICC A117.1 Clearances & Accessible Fixture Dimensions
ICC Plumbing Plans Examiner P3
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Administration & Plan Review Workflow
1.1 ICC P3 Exam Overview: Format, References & Content Weights 1.2 Scope, Intent, and Administrative Authority 1.3 Construction Documents & Submittal Requirements 1.4 Inspections, Testing Protocols & Department Operations
2 Chapter 2: General Regulations, Materials & Pipe Protection
2.1 Piping Protection, Trenching & Bedding 2.2 Approved Piping Materials, Joints & Connections 2.3 Piping Hangers, Supports & Thermal Expansion
3 Chapter 3: Plumbing Fixtures, Occupant Load & Minimum Fixture Counts
3.1 Occupant Load Calculation & IPC Table 403.1 3.2 Separate Facilities, Urinal Substitution & Exceptions 3.3 Public Toilet Facilities & Customer Access Requirements 3.4 Multi-User, Single-User & Family/Assisted-Use Facilities
4 Chapter 4: Accessible Plumbing Facilities & Fixture Standards
4.1 ICC A117.1 Clearances & Accessible Fixture Dimensions 4.2 Accessible Showers, Bathtubs & Drinking Fountains 4.3 Fixture Construction, Flow Rates & Water Conservation
5 Chapter 5: Water Heaters, Fuel Gas Piping & Venting
5.1 Water Heater Design, Location & Clearances 5.2 Temperature & Pressure Relief Valves & Discharge Piping 5.3 Safety Controls, Drain Pans & Thermal Expansion 5.4 Fuel Gas Pipe Sizing: Demand, Tables & Length Methods (IFGC 402) 5.5 Gas Water Heater Venting & Combustion Air Calculations (IFGC 304 & 503) 5.6 Gas Piping Materials, Installation, Testing & Appliance Connections (IFGC 403–411, 624)
6 Chapter 6: Water Supply, Backflow Protection & Nonpotable Systems
6.1 Water Supply Fixture Units (WSFU) & Demand Estimation 6.2 Water Service & Distribution Pipe Sizing Calculations 6.3 Maximum Velocities, Water Hammer & Pressure Regulators 6.4 Backflow Prevention & Cross-Connection Control 6.5 Nonpotable Water Systems: Identification, Separation & Storage Tanks 6.6 Graywater Reuse, Rainwater Collection, Reclaimed Water & Subsurface Graywater
7 Chapter 7: Sanitary Drainage System Design & Sizing
7.1 Drainage Principles, Minimum Slope & Flow Velocities 7.2 Drainage Fixture Units (DFU) & System Load Assignment 7.3 Horizontal Branch & Building Drain/Sewer Sizing 7.4 Soil & Waste Stacks, Offsets & Multi-Story Systems
8 Chapter 8: Sanitary Cleanouts, Sumps & Sewage Ejectors
8.1 Cleanout Sizing, Spacing & Installation Requirements 8.2 Backwater Valves & Flood Protection 8.3 Sewage Ejectors, Sumps & Macerating Systems
9 Chapter 9: Venting Systems & Vent Sizing
9.1 Venting Fundamentals, Terminations & Flood Rim Rules 9.2 Fixture Vents, Individual & Common Vents, Trap-to-Vent Distances 9.3 Wet Venting, Circuit Venting & Combination Waste-Vent Systems 9.4 Vent Stacks, Stack Vents & Air Admittance Valves
10 Chapter 10: Traps, Interceptors & Special Waste Systems
10.1 Fixture Traps, Trap Seals & Design Requirements 10.2 Grease Interceptors: Sizing, Types & Plan Review 10.3 Oil Separators, Sand Interceptors & Indirect / Chemical Waste
11 Chapter 11: Storm Drainage Systems & Roof Drainage Design
11.1 Storm Drainage Hydraulics & 100-Year Rainfall Rates 11.2 Sizing Vertical Conductors, Leaders & Horizontal Storm Drains 11.3 Secondary (Emergency) Roof Drainage & Subsoil Systems
12 Chapter 12: Health Care Plumbing Systems
12.1 Health Care Plumbing Scope, Fixtures & Special Equipment 12.2 Health Care Water Supply Protection, Water Services & Medical Gas
4.1 ICC A117.1 Clearances & Accessible Fixture Dimensions
Key Takeaways Explain This Topic AI
ICC A117.1-2017 requires a 60-by-56-inch clearance around a water closet; a wheelchair compartment is 60 by 56 inches (wall-hung) or 60 by 59 inches (floor-mounted).
Water closet centerlines are 16 to 18 inches from the side wall, and 17 to 19 inches in 35- to 37-inch-wide ambulatory compartments (A117.1 604.2).
A117.1-2017 side-wall grab bars include a 42-inch horizontal bar and an 18-inch vertical bar with its bottom 39 to 41 inches above the floor.
The A117.1-2017 rear grab bar is at least 36 inches long, within 6 inches of the side wall, and extends at least 42 inches from it.
Accessible lavatories are 34 inches maximum high with 27-inch knee clearance, and IPC 404.3 requires pipe covers per ASME A112.18.9 or ASTM C1822.
Last updated: October 2026
ICC A117.1 Clearances & Accessible Fixture Dimensions
Plumbing plans examiners must verify that commercial, institutional, and multi-family facilities provide barrier-free access in compliance with the International Plumbing Code (IPC Section 404) and the referenced accessibility standard, ICC A117.1-2017 ( Accessible and Usable Buildings and Facilities , Chapter 6). IPC 404.1 sends the scoping (how many and which fixtures must be accessible) to IBC Chapter 11, and IPC 404.2 requires accessible fixtures to be installed per ICC A117.1. The 2024 P3 reference list includes the plumbing provisions of A117.1-2017 (Resource A of the IPC) and the full standard. While architectural examiners evaluate door clearances and turning radiuses, the plumbing plans examiner is specifically responsible for verifying fixture mounting heights, clear floor spaces, centerline offsets, piping thermal protection, and grab bar structural provisions shown on plumbing floor plans, fixture schedules, and riser diagrams.
Wheelchair-Accessible Water Closet Compartments (ICC A117.1 Section 604)
The geometry of an accessible toilet compartment is engineered to accommodate independent side, diagonal, and front transfers from a wheelchair to the water closet bowl. A common plans examiner error is conflating standard IPC fixture clearances with accessible fixture mandates. ┌────────────────────────────────────────────────────────┐
- │ Wheelchair-Accessible Stall Floor Space (Plan) │
- ├────────────────────────────────────────────────────────┤
- │ │
- │ ◄─────────────────── 60" Min Width ────────────────► │
- │ ┌──────────────────────────────────────────────────┐ │
- │ │ Rear Wall │ │
- │ │ ┌──────────┐◄─ 16"-18" ─►│ │ │
- │ │ │ Toilet │ Centerline │ │ │
- │ │ │ Bowl │ │ │ │
- │ │ └──────────┘ │ │ │
- │ │ │ │ │
- │ │ │ │▲ │
- │ │ │ ││ │
- │ │ │ 56" Min ││ │
- │ │ │ (Wall-Hung) ││ │
- │ │ │ OR ││ │
- │ │ │ 59" Min ││ │
- │ │ │ (Floor-Mounted) ││ │
- │ │ │ ││ │
- │ │ │ ││ │
- │ │ │ │▼ │
- │ └───────────────────────────┴──────────────────────┘ │
- │ │
- └────────────────────────────────────────────────────────┘
- Water Closet Clearance vs. Compartment Size
ICC A117.1-2017 uses two different rectangles, and exam questions often turn on which one applies:
Requirement A117.1-2017 Section Width Depth
Clearance around a water closet (toilet rooms) 604.3.1 and 604.3.2 60 inches minimum, measured from the side wall 56 inches minimum, measured from the rear wall
- Wheelchair accessible toilet compartment , wall-hung water closet 604.9.2.1 60 inches 56 inches
- Wheelchair accessible toilet compartment , floor-mounted water closet 604.9.2.1 60 inches 59 inches
- Alternate wheelchair accessible compartment 604.9.2.3 60 inches 84 inches
- Ambulatory accessible compartment 604.10.2 35 to 37 inches 60 inches
The extra 3 inches of compartment depth for floor-mounted water closets reflects the bowl and base projecting farther into the compartment than a wall-hung bowl.
Fixture Overlap and Encroachment Restrictions
Under ICC A117.1-2017 Section 604.3.3:
The water closet clearance may overlap the water closet itself, its grab bars, paper dispensers, sanitary napkin receptacles, coat hooks, shelves, accessible routes, the clear floor space at other fixtures, and the turning space.
No other fixtures or obstructions may be within the required water closet clearance. A lavatory whose counter or bowl projects into the 60-by-56-inch clearance is therefore not allowed. The 2017 edition removed the older allowance that let a lavatory sit in the clearance.
Turning space : A117.1-2017 Section 603.2.1 requires a turning space in the toilet room, outside any toilet compartment. In new construction, it is a 67-inch circle (or the permitted T-shaped space); the 60-inch circle applies only to existing buildings.
Centerline Distances (Section 604.2)
Standard Wheelchair-Accessible Compartment : The centerline of the water closet must be between 16 inches minimum and 18 inches maximum ( 406 mm 406\text{ mm} 406 mm to 457 mm 457\text{ mm} 457 mm ) from the adjacent side wall or partition. This strict tolerance ensures that the user can reach the side wall grab bar for leverage without excessive lateral reach.
Ambulatory Accessible Compartment : IBC 1110.2 scoping requires at least 5 percent of compartments to be wheelchair accessible where compartments are provided. Where a toilet room has a combined total of six or more water closet compartments and urinals , at least 5 percent of compartments must also be ambulatory accessible , in addition to the wheelchair compartment. The ambulatory compartment is 35 to 37 inches wide and at least 60 inches deep (604.10.2). The water closet centerline is 17 inches minimum to 19 inches maximum ( 432 mm 432\text{ mm} 432 mm to 483 mm 483\text{ mm} 483 mm ) from the side partition, and side-wall grab bars are provided on both sides (604.10.4).
Toilet Seat Height and Flush Controls (Sections 604.4 & 604.6)
Seat Height : The top of the toilet seat must be installed 17 inches minimum to 19 inches maximum ( 432 mm 432\text{ mm} 432 mm to 483 mm 483\text{ mm} 483 mm ) above the finished floor (AFF). Seats for public or employee toilet facilities are the hinged open-front type under IPC 425.3. Seats may not be sprung to return to a lifted position (A117.1 604.4).
Flush Controls (604.6) : Flush controls are hand operated or automatic and are located on the open side of the water closet. In ambulatory compartments they may be on either side. Hand-operated controls must meet Section 309 for operable parts: within the reach ranges of Section 308 (48 inches maximum for an unobstructed reach) and operable with one hand without tight grasping, pinching or twisting of the wrist, using 5 pounds-force ( 22.2 N 22.2\text{ N} 22.2 N ) maximum.
Grab Bar Dimensions, Geometry & Structural Ratings (ICC A117.1 Sections 604.5 & 609)
Grab bars provide stability during transfers and prevent catastrophic falls. Plan submittals must document bar length, mounting height, and wall clearance.
Grab Bar Location (A117.1-2017) Minimum Length Position Mounting Height
Side wall, horizontal (604.5.1.1) 42 inches ( 1065 mm 1065\text{ mm} 1065 mm ) Located ≤ \le ≤ 12 inches from the rear wall and extending ≥ \ge ≥ 54 inches from the rear wall 33 to 36 inches AFF to top of gripping surface (609.4)
Side wall, vertical (604.5.1.2, new in 2017) 18 inches ( 455 mm 455\text{ mm} 455 mm ) Centerline 39 to 41 inches from the rear wall Bottom of bar 39 to 41 inches AFF
Rear wall (604.5.2) 36 inches ( 915 mm 915\text{ mm} 915 mm ) Located ≤ \le ≤ 6 inches from the side wall and extending ≥ \ge ≥ 42 inches from the side wall 33 to 36 inches AFF
- Ambulatory compartment (604.10.4) Side-wall bars per 604.5.1 On both side walls 33 to 36 inches AFF
- Rear Grab Bar Placement Details
The 2017 edition measures the rear bar from the side wall , not from the water closet centerline: it starts within 6 inches of the side wall and extends at least 42 inches from that wall. With a water closet centered 16 to 18 inches from the side wall, that places most of the bar toward the open transfer side.
Exceptions (604.5.2) : The rear bar may be 24 inches long, centered on the water closet, where wall space does not permit 36 inches because of a recessed fixture next to the water closet. Where the administrative authority requires flush valve controls in a position that conflicts with the rear bar, the bar may be split or shifted to the open side of the toilet area.
Grab Bar Cross-Section and Structural Load
Cross-Sectional Dimensions : Circular grab bars must have an outside diameter of 1-1/4 inches to 2 inches ( 32 mm 32\text{ mm} 32 mm to 51 mm 51\text{ mm} 51 mm ) . Non-circular grab bars must have a perimeter between 4.0 inches and 4.8 inches ( 102 mm 102\text{ mm} 102 mm to 122 mm 122\text{ mm} 122 mm ) with a maximum cross-section dimension of 2 inches.
Wall Clearance (609.3) : The space between the grab bar and the wall must be 1-1/2 inches ( 38 mm 38\text{ mm} 38 mm ) . This spacing prevents a user's arm from slipping through and becoming trapped during a fall.
Structural Capacity : Grab bars, mounting brackets, and structural backing must withstand a concentrated shear and tensile load of at least 250 lbf 250\text{ lbf} 250 lbf ( 1112 N 1112\text{ N} 1112 N ) applied at any point in any direction.
Accessible Lavatories and Sinks (ICC A117.1 Section 606 & IPC Section 404)
Accessible lavatories must provide unobstructed forward approach clearance for a seated wheelchair user, along with critical thermal and mechanical protection. ┌────────────────────────────────────────────────────────┐
- │ Accessible Lavatory Clearances (Section) │
- ├────────────────────────────────────────────────────────┤
- │ │
- │ ┌───────────┐ ◄─── Rim Height: 34" Max │
- │ │ Lavatory │ │
- │ ┌─────┴───────────┴─────┐ │
- │ │ Insulated Piping │ │
- │ │ (ASME A112.18.9) │ │
- │ └───────────┬───────────┘ │
- │ │ │
- │ Knee Clearance: │ 8" Min Depth │
- │ 27" Min AFF ──► │◄─────────►│ │
- │ │ │ │
- │ │ │ │
- │ Toe Clearance: │ │ 17" Min, 25" Max Deep │
- │ Floor to 9" ──► │ │◄─────────────────────►││
- │ └───────────┴───────────────────────┘│
- │ ════════════════════════════════════════════════════ Finished Floor
- │ │
- └────────────────────────────────────────────────────────┘
- Height and Clearance Dimensions (A117.1-2017 Sections 305, 306 and 606)
Rim Height (606.3) : The front of the lavatory or sink must be at most 34 inches ( 865 mm 865\text{ mm} 865 mm ) AFF , measured to the higher of the rim or counter surface.
Knee Clearance (306.3) : Space between 9 and 27 inches AFF is knee clearance. It must be at least 27 inches high at the front and at least 8 inches deep at 27 inches AFF and 11 inches deep at 9 inches AFF , and may extend at most 25 inches under the element.
Toe Clearance (306.2) : Space from the floor to 9 inches AFF is toe clearance. Where required, it extends at least 17 inches under the element and at most 25 inches . Space more than 6 inches beyond the available knee clearance at 9 inches AFF does not count as toe clearance.
Clear Floor Space (305.3) : A forward-approach clear floor space of 30 by 52 inches in new construction (30 by 48 inches in existing buildings), which may include the knee and toe clearance.
Exceptions (606.2) : Children's lavatories may use 24-inch knee clearance where the rim is 31 inches or less (ages 6 through 12) or a parallel approach (ages 5 and younger). A single-occupant room reached only through a private office does not need knee and toe clearance.
Pipe Insulation and Protection (IPC 404.3 & A117.1 606.6)
Under IPC 404.3 and ICC A117.1-2017 Section 606.6, water supply and drain pipes under accessible lavatories and sinks must be insulated or otherwise configured to protect against contact , with no sharp or abrasive surfaces underneath. IPC 404.3 requires pipe coverings to comply with ASME A112.18.9 or ASTM C1822 .
Burn Hazard Prevention : Uninsulated hot water lines can burn wheelchair users who have little or no sensation in their legs.
Abrasion Prevention : Covers eliminate sharp edges, rough threads and exposed slip-joint nuts.
Faucets and Operating Controls (ICC A117.1 Section 606.4)
Faucets must comply with Section 309: operable with one hand without tight grasping, pinching, or twisting of the wrist, at 5 lbf ( 22.2 N 22.2\text{ N} 22.2 N ) maximum, and within the reach ranges of Section 308.
Hand-operated metering faucets must remain open for at least 10 seconds .
Automatic faucets are exempt from Section 309 if the reach depth to activate them and to the water flow is 11 inches maximum (606.4 exception).
Mirrors (603.3) : A mirror over a lavatory or counter has the bottom of the reflecting surface at most 40 inches ( 1015 mm 1015\text{ mm} 1015 mm ) AFF . Mirrors over lavatories are not required (except in Accessible units) if another mirror in the room has its bottom edge at most 35 inches ( 890 mm 890\text{ mm} 890 mm ) AFF .
Plan Examiner Review Checklist: Accessible Fixtures
When conducting a plan review of toilet facilities on architectural and plumbing sheets, verify each item in the following checklist:
Verification Item Code Reference Required Value / Threshold Common Plan Violation
Wheelchair Compartment Width ICC A117.1 604.9.2.1 ≥ 60 inches \ge 60\text{ inches} ≥ 60 inches clear Interior dimension reduced by finish tile thickness
Floor-Mounted Compartment Depth ICC A117.1 604.9.2.1 ≥ 59 inches \ge 59\text{ inches} ≥ 59 inches clear Drawn at 56 inches (only permitted for wall-hung)
Turning Space (new construction) ICC A117.1 603.2.1 / 304.3 67-inch circle or T-shape, outside compartments Drawn as a 60-inch circle (existing-building value)
Water Closet Centerline ICC A117.1 604.2 16 to 18 inches to side wall Shown at 15 inches (standard IPC) or > 18 > 18 > 18 inches
Flush Control Location ICC A117.1 604.6 On open transfer side, ≤ 48 " \le 48" ≤ 48" AFF Valve actuator installed on the side wall side
Side Wall Grab Bars ICC A117.1 604.5.1 Horizontal ≥ 42 " \ge 42" ≥ 42" long, ≤ 12 " \le 12" ≤ 12" from rear wall, to ≥ 54 " \ge 54" ≥ 54" ; plus 18" vertical bar Vertical bar omitted (2009-era detail)
Rear Wall Grab Bar ICC A117.1 604.5.2 ≥ 36 " \ge 36" ≥ 36" long, ≤ 6 " \le 6" ≤ 6" from side wall, to ≥ 42 " \ge 42" ≥ 42" from side wall Bar centered on the toilet (2009-era layout)
Lavatory Rim Height ICC A117.1 606.3 ≤ 34 inches \le 34\text{ inches} ≤ 34 inches AFF Counter shown at standard 36-inch kitchen height
Knee Under-Clearance ICC A117.1 306.3 ≥ 27 " \ge 27" ≥ 27" high; 8" deep at 27", 11" deep at 9" Deep apron panels encroaching below 27 inches
Under-Sink Pipe Protection IPC 404.3 / A117.1 606.6 Covers per ASME A112.18.9 or ASTM C1822 Exposed P-trap and stops with no protection note