Study guide
12.1 Health Care Plumbing Scope, Fixtures & Special Equipment
ICC Plumbing Plans Examiner P3
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Administration & Plan Review Workflow
1.1 ICC P3 Exam Overview: Format, References & Content Weights 1.2 Scope, Intent, and Administrative Authority 1.3 Construction Documents & Submittal Requirements 1.4 Inspections, Testing Protocols & Department Operations
2 Chapter 2: General Regulations, Materials & Pipe Protection
2.1 Piping Protection, Trenching & Bedding 2.2 Approved Piping Materials, Joints & Connections 2.3 Piping Hangers, Supports & Thermal Expansion
3 Chapter 3: Plumbing Fixtures, Occupant Load & Minimum Fixture Counts
3.1 Occupant Load Calculation & IPC Table 403.1 3.2 Separate Facilities, Urinal Substitution & Exceptions 3.3 Public Toilet Facilities & Customer Access Requirements 3.4 Multi-User, Single-User & Family/Assisted-Use Facilities
4 Chapter 4: Accessible Plumbing Facilities & Fixture Standards
4.1 ICC A117.1 Clearances & Accessible Fixture Dimensions 4.2 Accessible Showers, Bathtubs & Drinking Fountains 4.3 Fixture Construction, Flow Rates & Water Conservation
5 Chapter 5: Water Heaters, Fuel Gas Piping & Venting
5.1 Water Heater Design, Location & Clearances 5.2 Temperature & Pressure Relief Valves & Discharge Piping 5.3 Safety Controls, Drain Pans & Thermal Expansion 5.4 Fuel Gas Pipe Sizing: Demand, Tables & Length Methods (IFGC 402) 5.5 Gas Water Heater Venting & Combustion Air Calculations (IFGC 304 & 503) 5.6 Gas Piping Materials, Installation, Testing & Appliance Connections (IFGC 403–411, 624)
6 Chapter 6: Water Supply, Backflow Protection & Nonpotable Systems
6.1 Water Supply Fixture Units (WSFU) & Demand Estimation 6.2 Water Service & Distribution Pipe Sizing Calculations 6.3 Maximum Velocities, Water Hammer & Pressure Regulators 6.4 Backflow Prevention & Cross-Connection Control 6.5 Nonpotable Water Systems: Identification, Separation & Storage Tanks 6.6 Graywater Reuse, Rainwater Collection, Reclaimed Water & Subsurface Graywater
7 Chapter 7: Sanitary Drainage System Design & Sizing
7.1 Drainage Principles, Minimum Slope & Flow Velocities 7.2 Drainage Fixture Units (DFU) & System Load Assignment 7.3 Horizontal Branch & Building Drain/Sewer Sizing 7.4 Soil & Waste Stacks, Offsets & Multi-Story Systems
8 Chapter 8: Sanitary Cleanouts, Sumps & Sewage Ejectors
8.1 Cleanout Sizing, Spacing & Installation Requirements 8.2 Backwater Valves & Flood Protection 8.3 Sewage Ejectors, Sumps & Macerating Systems
9 Chapter 9: Venting Systems & Vent Sizing
9.1 Venting Fundamentals, Terminations & Flood Rim Rules 9.2 Fixture Vents, Individual & Common Vents, Trap-to-Vent Distances 9.3 Wet Venting, Circuit Venting & Combination Waste-Vent Systems 9.4 Vent Stacks, Stack Vents & Air Admittance Valves
10 Chapter 10: Traps, Interceptors & Special Waste Systems
10.1 Fixture Traps, Trap Seals & Design Requirements 10.2 Grease Interceptors: Sizing, Types & Plan Review 10.3 Oil Separators, Sand Interceptors & Indirect / Chemical Waste
11 Chapter 11: Storm Drainage Systems & Roof Drainage Design
11.1 Storm Drainage Hydraulics & 100-Year Rainfall Rates 11.2 Sizing Vertical Conductors, Leaders & Horizontal Storm Drains 11.3 Secondary (Emergency) Roof Drainage & Subsoil Systems
12 Chapter 12: Health Care Plumbing Systems
12.1 Health Care Plumbing Scope, Fixtures & Special Equipment 12.2 Health Care Water Supply Protection, Water Services & Medical Gas
12.1 Health Care Plumbing Scope, Fixtures & Special Equipment
Key Takeaways Explain This Topic AI
IPC 609.1 applies health care plumbing rules to Group I-1, Group I-2, ambulatory care, medical offices, research laboratories and pharmaceutical manufacturing (Group F).
IPC 609.5 prohibits jet or water-supplied orifices in water closet bowls or clinical sinks, other than the flush connection.
IPC 415.1 requires each clinical sink to have a flushometer valve, flushometer tank or flush tank.
IPC 915.1 prohibits a combination waste and vent system from receiving the discharge of a clinical sink.
IPC 609.8 requires a leakage diverter or bleed line on the water supply control valve of each directly filled water sterilizer.
Last updated: October 2026
Health Care Plumbing Scope, Fixtures & Special Equipment
Health care plumbing makes up 5 percent of the ICC P3 exam. The outline splits it into installation of fixtures and protection of the water supply . This section covers fixtures and equipment, and Section 12.2 covers water supply protection. The governing text is IPC Section 609 , which adds to the rest of the code rather than replacing it, plus related rules in Chapters 4, 6, 8 and 9.
Scope: Where Section 609 Applies (IPC 609.1)
IPC 609.1 covers the parts of health care plumbing that differ from other buildings. It applies to the special devices and equipment installed and maintained in:
- Occupancy or Use Typical Examples
- Group I-1 Assisted living and residential care
- Group I-2 Hospitals, nursing homes and detoxification facilities with 24-hour medical care
- Ambulatory care facilities Outpatient surgery centers
- Medical offices Clinics and physician or dental offices
- Research and testing laboratories Hospital, university and commercial labs
- Group F pharmaceutical manufacturing Plants that make drugs and medicines
All other IPC chapters still apply. For example, a hospital's restroom water closets follow Chapter 4, and its drains follow Chapters 7 and 9.
Minimum Fixtures in Health Care Occupancies (IPC Table 403.1)
The 2024 Table 403.1 splits hospital and nursing-home rows into care recipient sleeping units, treatment areas, employee facilities and visitor facilities. Hospital care recipient sleeping units need 1 water closet and 1 lavatory per care recipient sleeping unit . Two footnotes matter in plan review:
Footnote b: Toilet facilities for employees must be separate from facilities for care recipients or inmates.
Footnote c: A single-user toilet room with one water closet and one lavatory may serve not more than two adjacent care recipient sleeping units , if each unit has direct access to the toilet room and the room provides privacy.
Plan review tip: A toilet room shared by three patient rooms, or one reached from a corridor, does not meet footnote c.
Clinical Sinks and Bedpan Washers
A clinical sink is a flushing-rim fixture in a soiled utility room, used to empty bedpans and dispose of bodily wastes. Like a water closet, it depends on trap siphonage to empty.
Flushing device (IPC 415.1): Each water closet, urinal, clinical sink and any fixture that depends on trap siphonage must have a flushometer valve, flushometer tank or flush tank . The device must supply enough water at the right rate to flush, cleanse the fixture and refill the trap.
No auxiliary jets (IPC 609.5): Jet or water-supplied orifices, except those supplied by the flush connection , may not be located in or connected to a water closet bowl or clinical sink. An approved bidet installation is not prohibited. Bedpan rinse sprays built into a clinical sink bowl would violate this rule.
Flush volume (Table 604.4, exception 3): Clinical sinks using not more than 4-1/2 gallons per flushing cycle are exempt from the general water closet flush limits.
No combination waste and vent (IPC 915.1): A combination waste and vent system may serve only floor drains, sinks, lavatories and drinking fountains, and may not receive a clinical sink's discharge . A clinical sink therefore needs a conventional vent.
Bedpan washer hoses (IPC 608.3.1): Vacuum breakers for bedpan washer hoses must be at least 5 feet above the floor . Section 12.2 covers the related supply protection rules. CLINICAL SINK PLAN REVIEW (IPC 415.1, 609.5, 915.1)
- Flushometer valve (415.1)
- │
- ┌─────┴──────────────┐
- │ ╲ flushing rim ╱│ ◄─ No other jets in the bowl (609.5)
- │ ╲_____________╱ │
- └────────┬───────────┘
- │ Trap (integral)
- ▼
- Conventional DWV with a vent
- (NOT a combination waste and vent system, 915.1)
- Sterilizers and Clinical Equipment
Leakage diverter (IPC 609.8): Each water sterilizer filled through directly connected piping needs an approved leakage diverter or bleed line on its water supply control valve. The diverter shows any leakage of unsterile water and carries it away from the sterile zone.
Indirect waste (IPC 802.1.3): Where sterilizers and similar devices discharge potable clear water to the drainage system, the discharge goes through an indirect waste pipe with an air gap . A direct connection could let sewage back up into the sterilizer.
Clinical, hydrotherapeutic and radiological equipment (IPC 609.6): Any equipment supplied with water or discharging to the waste system must meet Section 609 and the Section 608 backflow rules. Examples include imaging film processors, hydrotherapy tanks and dialysis equipment.
Special equipment (IPC 801.2): Devices used for sterilization, distillation, processing or cooling that discharge to the drainage system must be protected against backflow, flooding, fouling, contamination and stoppage.
Condensate Traps and Hot Water
Condensate drain trap seal (IPC 609.7): In health care facilities, condensate traps must have a water supply for cleaning, flushing and resealing the trap. The trap must discharge through an air gap per Section 608. Without reseal water, a dry condensate trap in a hospital air handler could pull contaminated air into the system.
Hot water (IPC 609.3): Hot water must be supplied for all hospital fixture, kitchen and laundry needs. Special fixtures and equipment get hot water at the temperature specified by the manufacturer . The system is installed per Section 607 , including tempered water and recirculation rules.
Plan Reviewer Verification Checklist: Health Care Fixtures
Occupancy Check: Section 609 applies if the project is I-1, I-2, ambulatory care, a medical office, a lab or pharmaceutical manufacturing.
Patient Toilets: Shared single-user toilet rooms serve no more than two adjacent care recipient units, with direct access and privacy (Table 403.1 note c).
Separate Staff Rooms: Employee toilet facilities are separate from care recipient facilities (Table 403.1 note b).
Clinical Sinks: Each has a flushometer or flush tank, no auxiliary bowl jets, and a conventional vent (415.1, 609.5, 915.1).
Sterilizers: Directly filled units have leakage diverters (609.8) and discharge through an air gap (802.1.3).
Condensate Traps: Each has reseal water and an air-gapped discharge (609.7).