Study guide

9.3 Wet Venting, Circuit Venting & Combination Waste-Vent Systems

ICC Plumbing Plans Examiner P3

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Administration & Plan Review Workflow

1.1 ICC P3 Exam Overview: Format, References & Content Weights 1.2 Scope, Intent, and Administrative Authority 1.3 Construction Documents & Submittal Requirements 1.4 Inspections, Testing Protocols & Department Operations

2 Chapter 2: General Regulations, Materials & Pipe Protection

2.1 Piping Protection, Trenching & Bedding 2.2 Approved Piping Materials, Joints & Connections 2.3 Piping Hangers, Supports & Thermal Expansion

3 Chapter 3: Plumbing Fixtures, Occupant Load & Minimum Fixture Counts

3.1 Occupant Load Calculation & IPC Table 403.1 3.2 Separate Facilities, Urinal Substitution & Exceptions 3.3 Public Toilet Facilities & Customer Access Requirements 3.4 Multi-User, Single-User & Family/Assisted-Use Facilities

4 Chapter 4: Accessible Plumbing Facilities & Fixture Standards

4.1 ICC A117.1 Clearances & Accessible Fixture Dimensions 4.2 Accessible Showers, Bathtubs & Drinking Fountains 4.3 Fixture Construction, Flow Rates & Water Conservation

5 Chapter 5: Water Heaters, Fuel Gas Piping & Venting

5.1 Water Heater Design, Location & Clearances 5.2 Temperature & Pressure Relief Valves & Discharge Piping 5.3 Safety Controls, Drain Pans & Thermal Expansion 5.4 Fuel Gas Pipe Sizing: Demand, Tables & Length Methods (IFGC 402) 5.5 Gas Water Heater Venting & Combustion Air Calculations (IFGC 304 & 503) 5.6 Gas Piping Materials, Installation, Testing & Appliance Connections (IFGC 403–411, 624)

6 Chapter 6: Water Supply, Backflow Protection & Nonpotable Systems

6.1 Water Supply Fixture Units (WSFU) & Demand Estimation 6.2 Water Service & Distribution Pipe Sizing Calculations 6.3 Maximum Velocities, Water Hammer & Pressure Regulators 6.4 Backflow Prevention & Cross-Connection Control 6.5 Nonpotable Water Systems: Identification, Separation & Storage Tanks 6.6 Graywater Reuse, Rainwater Collection, Reclaimed Water & Subsurface Graywater

7 Chapter 7: Sanitary Drainage System Design & Sizing

7.1 Drainage Principles, Minimum Slope & Flow Velocities 7.2 Drainage Fixture Units (DFU) & System Load Assignment 7.3 Horizontal Branch & Building Drain/Sewer Sizing 7.4 Soil & Waste Stacks, Offsets & Multi-Story Systems

8 Chapter 8: Sanitary Cleanouts, Sumps & Sewage Ejectors

8.1 Cleanout Sizing, Spacing & Installation Requirements 8.2 Backwater Valves & Flood Protection 8.3 Sewage Ejectors, Sumps & Macerating Systems

9 Chapter 9: Venting Systems & Vent Sizing

9.1 Venting Fundamentals, Terminations & Flood Rim Rules 9.2 Fixture Vents, Individual & Common Vents, Trap-to-Vent Distances 9.3 Wet Venting, Circuit Venting & Combination Waste-Vent Systems 9.4 Vent Stacks, Stack Vents & Air Admittance Valves

10 Chapter 10: Traps, Interceptors & Special Waste Systems

10.1 Fixture Traps, Trap Seals & Design Requirements 10.2 Grease Interceptors: Sizing, Types & Plan Review 10.3 Oil Separators, Sand Interceptors & Indirect / Chemical Waste

11 Chapter 11: Storm Drainage Systems & Roof Drainage Design

11.1 Storm Drainage Hydraulics & 100-Year Rainfall Rates 11.2 Sizing Vertical Conductors, Leaders & Horizontal Storm Drains 11.3 Secondary (Emergency) Roof Drainage & Subsoil Systems

12 Chapter 12: Health Care Plumbing Systems

12.1 Health Care Plumbing Scope, Fixtures & Special Equipment 12.2 Health Care Water Supply Protection, Water Services & Medical Gas

9.3 Wet Venting, Circuit Venting & Combination Waste-Vent Systems

Key Takeaways Explain This Topic AI

IPC 912.1 permits wet venting of any combination of fixtures within two bathroom groups on the same floor, and other fixtures must connect downstream.

IPC Table 912.3 sizes wet vents at 1 dfu for 1-1/2 inch, 4 dfu for 2 inch, 6 dfu for 2-1/2 inch and 12 dfu for 3 inch.

IPC 914.1 permits circuit venting of not more than eight fixtures, with the vent connected between the two most upstream fixture drains (914.2).

A circuit-vented branch needs a relief vent when it serves four or more water closets and connects to a stack receiving upper-floor branches (IPC 914.4).

IPC 915.1 limits combination waste and vent systems to floor drains, sinks, lavatories and drinking fountains, sloped no more than 1/2 inch per foot.

Last updated: October 2026

Wet Venting, Circuit Venting & Combination Waste-Vent Systems

While individual re-venting provides robust protection, installing a dedicated dry vent for every individual fixture in complex commercial buildings or dense residential facilities is often structurally impractical, excessively costly, and aerially congested. The 2024 IPC provides several alternatives; this section covers the three most tested: Wet Venting (Section 912), Circuit Venting (Section 914) and Combination Waste and Vent Systems (Section 915). The related waste stack vent (913) and island fixture vent (916) are summarized at the end. Each system balances liquid conveyance and atmospheric air flow within shared pipe conduits. Plans examiners must master the strict fixture limitations, geometry, and sizing criteria that distinguish these three methods.

Wet Venting of Bathroom Groups (IPC Section 912)

A wet vent is a vent that also carries drainage. In the IPC it is limited to bathroom groups .

What May Be Wet Vented (IPC 912.1 and 912.1.1)

Horizontal wet vent (912.1): Any combination of fixtures within two bathroom groups located on the same floor level may be vented by a horizontal wet vent. The wet vent runs from the dry vent connection, in the direction of flow, to the most downstream fixture drain connection. Each wet-vented fixture drain connects independently to the wet vent.

Only bathroom group fixtures: Only fixtures within the bathroom groups may connect to the wet-vented horizontal branch. Any additional fixtures discharge downstream of the horizontal wet vent.

Vertical wet vent (912.1.1): The same two-bathroom-group limit applies. The wet vent runs from the dry vent connection down to the lowest fixture drain connection. Water closet drains connect at the same elevation, and other fixture drains connect above or at that elevation. The dry vent connection is an individual or common vent serving one or two fixtures.

Bathroom group (Chapter 2): A water closet, a lavatory, and a bathtub or shower, with or without a bidet and an emergency floor drain, located together on the same floor level.

Caution

Kitchen sinks, bar sinks, clothes washers, service sinks and other non-bathroom fixtures may not connect to the wet-vented section. If they share the branch, they must connect downstream of the wet vent, so grease and suds do not foul the shared air path. TYPICAL HORIZONTAL WET VENT LAYOUT

  • DRY VENT (individual or common vent)
  • ▲
  • │
  • LAVATORY │ (at most ONE wet-vented fixture drain may
  • (1 DFU) │ discharge upstream of the dry-vented connection)
  • │ │
  • ┌┴┐ │
  • └┬┘ │
  • └────────┴───────────── WET VENT (Table 912.3) ──────┐
  • │ │ │
  • BATHTUB WATER CLOSET ▼
  • (2 DFU) (3 DFU, private) TO BRANCH/STACK
  • Each fixture drain connects independently
  • Dry Vent Connection (IPC 912.2.1 and 912.2.2)

Horizontal wet vent: The dry vent is an individual or common vent for any bathroom group fixture except an emergency floor drain . Where the dry vent connects to a water closet fixture drain, that drain connects horizontally to the wet-vent system. Not more than one wet-vented fixture drain may discharge upstream of the dry-vented fixture drain connection.

Vertical wet vent: The dry vent is an individual or common vent for the most upstream fixture drain.

Sizing (IPC 912.3 and Table 912.3)

The dry vent serving the wet vent is sized on the largest required diameter of pipe within the wet-vent system it serves (and per 906.2). The wet vent is sized by the DFU discharged to it:

  • Wet Vent Pipe Size (inches) Drainage Fixture Unit Load (dfu)
  • 1-1/2 1
  • 2 4
  • 2-1/2 6
  • 3 12

Example: Two private bathroom groups, each with a 1.6-gpf water closet (3 dfu), a lavatory (1) and a bathtub (2), total 12 dfu on the wet vent. If the dry vent is on one lavatory, its 1 dfu does not discharge to the wet vent, so the wet vent carries 11 dfu and must be 3 inches.

Circuit Venting for Battery Installations (IPC Section 914)

Circuit venting serves a row (battery) of fixtures on one horizontal branch, such as water closets in a school or stadium restroom. CIRCUIT-VENTED BATTERY (6 WATER CLOSETS)

  • CIRCUIT VENT (906.2 size)
  • ▲ between the two most
  • │ upstream fixture drains
  • WC #6 WC #5 WC #4 WC #3 WC #2 WC #1
  • ┌─┐ ┌─┐ ┌─┐ ┌─┐ ┌─┐ ┌─┐
  • └┬┘ └┬┘ └┬┘ └┬┘ └┬┘ └┬┘
  • ─────────────────┴───────┴───────┴───────┴───────┴───────┴───
  • ▲ ▲ ▲
  • │ │ │ Vent section: slope not over
  • SOIL/WASTE RELIEF VENT 1 in 12; sized for total discharge
  • STACK (4+ WCs AND stack receives upper-floor branches)
  • Code Rules for Circuit Venting (IPC 914.1 through 914.5)

Maximum Eight Fixtures (914.1): Not more than eight fixtures connected to a horizontal branch drain may be circuit vented. Several circuit-vented branches may be connected together, with each group of eight or fewer treated as a separate circuit vent (914.1.1).

Horizontal Connections (914.1): Each fixture drain connects horizontally to the branch being circuit vented. The branch is classified as a vent from the most downstream fixture connection to the most upstream one.

Vent Connection (914.2): The circuit vent connects between the two most upstream fixture drains , to the horizontal branch, installed per Section 905. The circuit vent pipe may not receive soil or waste.

Slope and Size of the Branch (914.3): The slope of the vent section of the branch may be not greater than 1 unit vertical in 12 horizontal (8.3 percent) . The entire vent section is sized for the total drainage discharge to the branch.

Circuit Vent Size (906.2): At least one-half the required diameter of the drain served , and not less than 1-1/4 inches , increased one size where its developed length exceeds 40 feet.

Relief Vent (IPC 914.4)

A relief vent is required for circuit-vented branches receiving the discharge of four or more water closets and connecting to a drainage stack that receives soil or waste from upper horizontal branches . Both conditions must be present.

Connection (914.4.1): Between the stack and the most downstream fixture drain of the circuit vent, installed per Section 905.

Relief vent as a drain (914.4.2): The relief vent may serve as a fixture drain or fixture branch for fixtures in the same branch interval, with a maximum discharge of 4 fixture units .

Additional fixtures (914.5): Other fixtures may discharge to the branch if they are on the same floor and are individually or common vented.

Combination Waste and Vent Systems (IPC Section 915)

In open areas such as showrooms, laboratories and kitchens, there may be nowhere to run vertical vents. A combination waste and vent system uses an oversized horizontal drain whose upper part stays open for air. CONVENTIONAL DRAIN COMBINATION WASTE & VENT

(Sized for flow) (Larger pipe, flatter slope)

  • ┌──────────────┐ ┌──────────────┐
  • │ AIR SPACE │ │ CONTINUOUS │
  • ├──────────────┤ │ AIR SPACE │
  • │ WASTEWATER │ ├──────────────┤
  • └──────────────┘ │ WASTEWATER │
  • └──────────────┘
  • Fixtures Allowed (IPC 915.1)

A combination waste and vent system shall not serve fixtures other than floor drains, sinks, lavatories and drinking fountains , and it may not receive the discharge of a clinical sink. Water closets, urinals, bathtubs, showers and clothes washers are excluded.

Installation and Sizing (IPC 915.2)

Vertical pipe (915.2): The only vertical pipe is the connection between the fixture drain and the horizontal combination pipe, and it may not exceed 8 feet .

Slope (915.2.1): Not more than 1/2 inch per foot (4 percent) and not less than Table 704.1. A steeper pipe runs fast and turbulent, and waves can fill the pipe and close off the air space.

Size (915.2.2): Not less than Table 915.2.2 . The horizontal length is unlimited.

Pipe Diameter (inches) Max dfu, Connecting to a Horizontal Branch or Stack Max dfu, Connecting to a Building Drain or Subdrain

  • 2 3 4
  • 2-1/2 6 26
  • 3 12 31
  • 4 20 50
  • 5 160 250
  • 6 360 575

Dry vent (915.2.3): The system has a dry vent connected at any point, or connects to a horizontal drain that serves vented fixtures on the same floor. A system connecting to a building drain that receives only the discharge of stacks must have a dry vent. The vent rises vertically to at least 6 inches above the flood level rim of the highest fixture vented before offsetting.

Vent size (915.2.4): Sized for the total dfu load per Section 906.2.

Fixture connection (915.2.5): Each fixture drain or branch connects to the combination pipe within the Table 909.1 distance, and the combination pipe is the fixture's vent.

Related Methods: Waste Stack Vents and Island Fixtures

Waste stack vent (913): A vertical waste stack with no offsets between the lowest and highest fixture connections may vent the fixtures discharging to it. It may not receive water closets or urinals, and it needs a stack vent at least the size of the waste stack. The stack is sized by Table 913.4 (for example, 3 inches carries 24 dfu total and 4 inches carries 50 dfu) and stays one size throughout.

Island fixture venting (916): Permitted only for sinks and lavatories, including residential kitchen sinks with a dishwasher or disposer. The vent rises above the fixture's drainage outlet before turning down. Below the flood level rim, it is installed like drainage pipe, connects full size to a vertical drain or the top half of a horizontal drain, and has cleanouts for rodding.

Comparison Matrix: Alternative Venting Systems

  • Design Parameter Wet Venting Circuit Venting Combination Waste & Vent
  • Governing Section IPC 912 IPC 914 IPC 915

Eligible Fixtures Fixtures within two bathroom groups on one floor Up to 8 fixtures per branch Floor drains, sinks, lavatories, drinking fountains

  • Water Closets Allowed? Yes (within the bathroom groups) Yes No
  • Sizing Rule Table 912.3 (3 inch = 12 dfu) Vent section sized for total discharge; vent per 906.2 Table 915.2.2
  • Slope Limit Normal Table 704.1 slopes Vent section not over 1 in 12 Not over 1/2 inch per foot
  • Relief Vent Trigger Not applicable 4+ water closets and stack with upper branches Not applicable