Study guide

6.1 Water Supply Fixture Units (WSFU) & Demand Estimation

ICC Plumbing Plans Examiner P3

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Administration & Plan Review Workflow

1.1 ICC P3 Exam Overview: Format, References & Content Weights 1.2 Scope, Intent, and Administrative Authority 1.3 Construction Documents & Submittal Requirements 1.4 Inspections, Testing Protocols & Department Operations

2 Chapter 2: General Regulations, Materials & Pipe Protection

2.1 Piping Protection, Trenching & Bedding 2.2 Approved Piping Materials, Joints & Connections 2.3 Piping Hangers, Supports & Thermal Expansion

3 Chapter 3: Plumbing Fixtures, Occupant Load & Minimum Fixture Counts

3.1 Occupant Load Calculation & IPC Table 403.1 3.2 Separate Facilities, Urinal Substitution & Exceptions 3.3 Public Toilet Facilities & Customer Access Requirements 3.4 Multi-User, Single-User & Family/Assisted-Use Facilities

4 Chapter 4: Accessible Plumbing Facilities & Fixture Standards

4.1 ICC A117.1 Clearances & Accessible Fixture Dimensions 4.2 Accessible Showers, Bathtubs & Drinking Fountains 4.3 Fixture Construction, Flow Rates & Water Conservation

5 Chapter 5: Water Heaters, Fuel Gas Piping & Venting

5.1 Water Heater Design, Location & Clearances 5.2 Temperature & Pressure Relief Valves & Discharge Piping 5.3 Safety Controls, Drain Pans & Thermal Expansion 5.4 Fuel Gas Pipe Sizing: Demand, Tables & Length Methods (IFGC 402) 5.5 Gas Water Heater Venting & Combustion Air Calculations (IFGC 304 & 503) 5.6 Gas Piping Materials, Installation, Testing & Appliance Connections (IFGC 403–411, 624)

6 Chapter 6: Water Supply, Backflow Protection & Nonpotable Systems

6.1 Water Supply Fixture Units (WSFU) & Demand Estimation 6.2 Water Service & Distribution Pipe Sizing Calculations 6.3 Maximum Velocities, Water Hammer & Pressure Regulators 6.4 Backflow Prevention & Cross-Connection Control 6.5 Nonpotable Water Systems: Identification, Separation & Storage Tanks 6.6 Graywater Reuse, Rainwater Collection, Reclaimed Water & Subsurface Graywater

7 Chapter 7: Sanitary Drainage System Design & Sizing

7.1 Drainage Principles, Minimum Slope & Flow Velocities 7.2 Drainage Fixture Units (DFU) & System Load Assignment 7.3 Horizontal Branch & Building Drain/Sewer Sizing 7.4 Soil & Waste Stacks, Offsets & Multi-Story Systems

8 Chapter 8: Sanitary Cleanouts, Sumps & Sewage Ejectors

8.1 Cleanout Sizing, Spacing & Installation Requirements 8.2 Backwater Valves & Flood Protection 8.3 Sewage Ejectors, Sumps & Macerating Systems

9 Chapter 9: Venting Systems & Vent Sizing

9.1 Venting Fundamentals, Terminations & Flood Rim Rules 9.2 Fixture Vents, Individual & Common Vents, Trap-to-Vent Distances 9.3 Wet Venting, Circuit Venting & Combination Waste-Vent Systems 9.4 Vent Stacks, Stack Vents & Air Admittance Valves

10 Chapter 10: Traps, Interceptors & Special Waste Systems

10.1 Fixture Traps, Trap Seals & Design Requirements 10.2 Grease Interceptors: Sizing, Types & Plan Review 10.3 Oil Separators, Sand Interceptors & Indirect / Chemical Waste

11 Chapter 11: Storm Drainage Systems & Roof Drainage Design

11.1 Storm Drainage Hydraulics & 100-Year Rainfall Rates 11.2 Sizing Vertical Conductors, Leaders & Horizontal Storm Drains 11.3 Secondary (Emergency) Roof Drainage & Subsoil Systems

12 Chapter 12: Health Care Plumbing Systems

12.1 Health Care Plumbing Scope, Fixtures & Special Equipment 12.2 Health Care Water Supply Protection, Water Services & Medical Gas

6.1 Water Supply Fixture Units (WSFU) & Demand Estimation

Key Takeaways Explain This Topic AI

IPC Appendix E Table E103.3(2) assigns WSFU load values; Table 604.3 gives fixture outlet flow and pressure, not fixture units.

A public flushometer-valve water closet carries 10 WSFU and a public lavatory 2.0 total WSFU under IPC Table E103.3(2).

Separate hot and cold WSFU values are three-fourths of each fixture's total, so mains serving both use the Total column.

IPC Table E103.3(3) converts 50 WSFU to 50 gpm for flushometer-valve systems and 29.1 gpm for flush tank systems.

IPC Appendix E Section E102.2.2 adds continuous demands, such as irrigation and cooling equipment, in gpm to the fixture demand.

Last updated: October 2026

Water Supply Fixture Units (WSFU) & Demand Estimation

Accurate determination of water demand is the prerequisite for designing and reviewing any building water distribution network. In commercial plumbing plan examination, undersized piping produces severe pressure drops, fixture starvation, cavitation, and thermal shock in mixing valves, while oversized piping incurs unnecessary capital cost, promotes stagnation, and accelerates internal microbial growth such as Legionella pneumophila . IPC 604.1 requires the water distribution system to be designed by accepted engineering practice using approved methods. IPC 604.3 and Table 604.3 set the minimum flow and pressure at each fixture outlet. IPC Appendix E provides the classic water supply fixture unit (WSFU) method for converting intermittent fixture loads into a design flow in gallons per minute (gpm). Appendix E applies only where the jurisdiction adopts it (IPC 101.2.1), but it is the method plans examiners most often see.

The Fallacy of Sizing by Cross-Sectional Pipe Area

A frequent error encountered in unengineered submissions is the attempt to size water mains by arithmetically summing the nominal diameters or cross-sectional areas of downstream branch pipes. For example, assuming that two 1/2-inch fixture branches require a 1-inch supply line ( 1 / 2 " + 1 / 2 " = 1 " 1/2" + 1/2" = 1" 1/2" + 1/2" = 1" ) violates fundamental fluid dynamics. The internal cross-sectional area of a nominal 1-inch pipe is roughly four times that of a 1/2-inch pipe ( A = π r 2 A = \pi r^2 A = π r 2 ). More importantly, plumbing fixtures in any multi-fixture building operate intermittently and independently. Sizing for 100 percent simultaneous operation would result in grossly oversized infrastructure that stagnates water and inflates construction costs.

To resolve this challenge, modern plumbing codes rely on the Water Supply Fixture Unit (WSFU) methodology, originally formulated by Dr. Roy B. Hunter of the National Bureau of Standards (NBS Report BMS65). A fixture unit is a dimensionless relative weighting factor that reflects:

  • The volume flow rate discharged by the fixture during operation ( q q q in gpm)
  • The average duration of a single operational cycle ( t t t in seconds)
  • The average frequency of use or time interval between successive operations ( T T T in seconds)

The probability p p p that a single fixture is operating at any random instant is expressed as:

p = t T p = \frac{t}{T} p = T t ​

Using binomial probability distributions, Hunter established the design curve that predicts the peak simultaneous flow rate that will not be exceeded more than 1 percent of the time during peak demand hours.

Assigning WSFU Values (IPC Appendix E, Table E103.3(2))

WSFU load values are listed in IPC Appendix E Table E103.3(2), "Load Values Assigned to Fixtures." Do not confuse it with IPC Table 604.3, which gives each fixture's required flow rate and flow pressure. The table separates fixtures by occupancy:

Private: Fixtures in dwelling units, hotel guest rooms and similar private use, which see lower frequency of use.

Public: Fixtures in offices, schools, restaurants, terminals and other public or employee facilities, which see heavy, frequent use.

Selected Values from IPC Table E103.3(2)

  • Fixture Occupancy Supply Control Cold WSFU Hot WSFU Total WSFU
  • Water closet Public Flushometer valve 10.0 — 10.0
  • Water closet Private Flushometer valve 6.0 — 6.0
  • Water closet Public Flush tank 5.0 — 5.0
  • Water closet Private Flush tank 2.2 — 2.2
  • Water closet Public or private Flushometer tank 2.0 — 2.0
  • Urinal Public 1-inch flushometer valve 10.0 — 10.0
  • Urinal Public 3/4-inch flushometer valve 5.0 — 5.0
  • Urinal Public Flush tank 3.0 — 3.0
  • Lavatory Public Faucet 1.5 1.5 2.0
  • Lavatory Private Faucet 0.5 0.5 0.7
  • Bathtub Public Faucet 3.0 3.0 4.0
  • Bathtub Private Faucet 1.0 1.0 1.4
  • Shower head Public Mixing valve 3.0 3.0 4.0
  • Shower head Private Mixing valve 1.0 1.0 1.4
  • Kitchen sink Hotel, restaurant Faucet 3.0 3.0 4.0
  • Kitchen sink Private Faucet 1.0 1.0 1.4
  • Service sink Offices, etc. Faucet 2.25 2.25 3.0
  • Drinking fountain Offices, etc. 3/8-inch valve 0.25 — 0.25
  • Bathroom group Private Flush tank 2.7 1.5 3.6
  • Bathroom group Private Flushometer valve 6.0 3.0 8.0

Fixtures not listed (a hose bibb, for example) are assigned a load by comparing them with a listed fixture that uses water in similar quantities and at similar rates.

The Rule of Cold, Hot, and Total WSFU Separation

When reviewing plumbing drawings, examiners verify three separate sizing paths:

Cold Water Branches: Sized using the accumulated Cold WSFU of the fixtures served.

Hot Water Branches: Sized using the accumulated Hot WSFU of the fixtures served.

Building Supply and Mains Serving Both: Sized using the accumulated Total WSFU , including the cold water that feeds the water heater.

Why Cold WSFU + Hot WSFU Does Not Equal Total WSFU

For a public lavatory, Cold = 1.5 and Hot = 1.5, yet Total = 2.0. The table footnote explains why: the separate hot and cold loads are three-fourths of the total load for each fixture. A user mixes hot and cold, so neither side draws the whole fixture flow, but each branch must still carry most of it when the user picks a very hot or very cold setting. The main that serves both sides is sized with the Total column. Adding the hot and cold values (1.5 + 1.5 = 3.0) would overstate the main's load.

Converting WSFU to Peak Demand (IPC Table E103.3(3))

Once fixture units are summed, the designer converts them to peak gpm with Appendix E Table E103.3(3), "Table for Estimating Demand" . Its two columns follow Hunter's curves:

  • Supply systems predominantly for flushometer valves
  • Supply systems predominantly for flush tanks
  • WSFU to GPM Demand Comparison (values from Table E103.3(3))
  • Load (WSFU) Predominantly Flushometer Valves (gpm) Predominantly Flush Tanks (gpm)
  • 10 27.0 14.6
  • 20 35.0 19.6
  • 30 42.0 23.3
  • 40 46.0 26.3
  • 50 50.0 29.1
  • 70 58.0 35.0
  • 100 67.5 43.5
  • 140 77.0 52.5
  • 200 90.0 65.0
  • 300 108.0 85.0
  • 500 143.0 124.0
  • 750 177.0 170.0
  • 1,000 208.0 208.0 (the columns converge) Peak Flow (gpm)
  • │
  • 150 ─┼ . . . Flushometer valves (143 at 500)
  • │ . . . '
  • 100 ─┼ . . . ' _ _ _ _ Flush tanks (124 at 500)
  • │ . . ' _ _ _ - -
  • 50 ─┼ . ' _ _ - - -
  • │ . _ -
  • 0 ─┼─┴─────┼─────┼─────┼─────┼─────┼
  • 0 100 200 300 400 500 WSFU Load
  • Why the Flushometer Column Is Higher

At low loads, the flushometer column predicts far more flow than the flush tank column. A flushometer valve draws a large instantaneous flow; Table 604.3 lists 25 gpm at the outlet for flushometer-valve water closets, over a few seconds. A flush tank refills at a few gpm over about a minute. In a small system, a single flushometer valve dominates the peak, so the difference narrows only as the number of fixtures grows. By 1,000 WSFU the two columns are identical.

Note that the hot water side of a building with flushometer valves usually serves no flush valves, so its demand is often read from the flush tank column.

Continuous Demands (IPC Appendix E, Section E102.2.2)

Hunter's method assumes brief, random draws. Section E102.2.2 directs that continuous supply demands, in gallons per minute, for items such as lawn sprinklers and air conditioners be estimated and added to the total demand for fixtures . A cooling tower makeup line drawing 15 gpm for hours at a time is not a random draw, and converting it to fixture units would let the diversity curve shrink it.

Q design = Q fixtures (Table E103.3(3)) + ∑ Q continuous Q_{\text{design}} = Q_{\text{fixtures}}\text{ (Table E103.3(3))} + \sum Q_{\text{continuous}} Q design ​ = Q fixtures ​ (Table E103.3(3)) + ∑ Q continuous ​

Minimum Residual Pressure (Section E103.1)

Appendix E also sets the target residual pressure at the highest fixture group: at least 15 psi flowing where that group has flushometer valves, 8 psi flowing for flush tank supplies, and 25 psi flowing for blowout fixtures. Elevation changes cost 0.433 psi per foot .

Worked Example: Commercial Office Restroom Battery

Project Scope: A two-story office building has two public restroom groups with flushometer valves, one service sink, two drinking fountains, and an evaporative cooling tower makeup line.

  • Step 1: Tabulate Fixture Loads (Table E103.3(2))
  • Water closets (public, flushometer valve): 6 × 10.0 = 60.0 total | 60.0 cold
  • Urinals (public, 3/4-inch flushometer valve): 4 × 5.0 = 20.0 total | 20.0 cold
  • Lavatories (public): 6 × 2.0 = 12.0 total | 9.0 cold (6 × 1.5) | 9.0 hot (6 × 1.5)
  • Service sink: 1 × 3.0 = 3.0 total | 2.25 cold | 2.25 hot
  • Drinking fountains: 2 × 0.25 = 0.5 total | 0.5 cold
  • Step 2: Sum the Loads

Total WSFU: 60.0 + 20.0 + 12.0 + 3.0 + 0.5 = 95.5 60.0 + 20.0 + 12.0 + 3.0 + 0.5 = 95.5 60.0 + 20.0 + 12.0 + 3.0 + 0.5 = 95.5

Cold WSFU: 60.0 + 20.0 + 9.0 + 2.25 + 0.5 = 91.75 60.0 + 20.0 + 9.0 + 2.25 + 0.5 = 91.75 60.0 + 20.0 + 9.0 + 2.25 + 0.5 = 91.75

  • Hot WSFU: 9.0 + 2.25 = 11.25 9.0 + 2.25 = 11.25 9.0 + 2.25 = 11.25
  • Step 3: Read the Demand (Table E103.3(3), flushometer column)

At 90 WSFU = 64.3 gpm; at 100 WSFU = 67.5 gpm.

Interpolating for 95.5 WSFU: 64.3 + ( 5.5 10 × 3.2 ) = 66.1 gpm 64.3 + \left(\frac{5.5}{10} \times 3.2\right) = 66.1\text{ gpm} 64.3 + ( 10 5.5 ​ × 3.2 ) = 66.1 gpm

Step 4: Add Continuous Demand (E102.2.2)

The mechanical schedule shows 15.0 gpm of continuous cooling tower makeup during peak hours:

Q design = 66.1 gpm + 15.0 gpm = 81.1 gpm Q_{\text{design}} = 66.1\text{ gpm} + 15.0\text{ gpm} = 81.1\text{ gpm} Q design ​ = 66.1 gpm + 15.0 gpm = 81.1 gpm

The building supply, meter and service are sized for about 81 gpm , and the pressure budget must still deliver 15 psi flowing at the highest flushometer valve.

Step 5: Size the Hot Water Branch

The hot side serves 11.25 WSFU with no flush valves, so the flush tank column applies. At 11 WSFU the demand is 15.4 gpm and at 12 WSFU it is 16.0 gpm, so about 15.6 gpm .