Study guide

4.3 Duct Insulation Materials and Under-Floor Plenums (IRC M1601.3 and M1601.5)

ICC Residential Mechanical Inspector M1

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: General Administration & Requirements

1.1 Administrative Provisions, Permits, and Inspections 1.2 General Mechanical Requirements, Labeling, and Access 1.3 Equipment Clearances and Safety Controls

2 Chapter 2: Heating, Cooling & Water Heaters

2.1 Forced-Air Heating Systems and Furnaces 2.2 Heat Pumps and Air Conditioning Systems 2.3 Water Heaters: Sizing, Access, and Connections 2.4 Water Heaters: Venting, Clearances, and Relief Valves 2.5 Radiant and Hydronic Space Heating Systems 2.6 Evaporative Cooling and Floor/Wall Furnaces 2.7 Vented Decorative Appliances and Room Heaters

3 Chapter 3: Exhaust & Ventilation Systems

3.1 Clothes Dryer Exhaust 3.2 Range Hoods and Kitchen Exhaust Systems 3.3 Whole-House Ventilation and Bathroom Exhaust

4 Chapter 4: Duct Systems

4.1 Duct Design, Construction, and Materials (IRC Section M1601) 4.2 Duct Installation, Supports, and Sealing (IRC Section M1601.4) 4.3 Duct Insulation Materials and Under-Floor Plenums (IRC M1601.3 and M1601.5) 4.4 Return Air Openings and Prohibited Duct Locations (IRC Section M1602)

5 Chapter 5: Combustion Air

5.1 Combustion Air: Indoor Air and Forced Air Methods 5.2 Combustion Air: Outdoor Air Methods and Sizing

6 Chapter 6: Chimneys & Vents

6.1 Venting System Classifications and General Rules 6.2 Type B Vents and Single-Wall Metal Connectors 6.3 Masonry and Factory-Built Chimneys 6.4 Direct-Vent Systems and Vent Terminations

7 Chapter 7: Special Appliances, Boilers & Hydronic Piping

7.1 Boiler Installation, Operating Controls, and Safety Devices 7.2 Hydronic Piping Materials, Joints, and Supports 7.3 Special Piping, Solar Thermal, and Ground-Source Systems

8 Chapter 8: Fuel Gas Piping & Appliances

8.1 Fuel Gas Piping Materials, Fittings, and Joining Methods 8.2 Gas Pipe Sizing and Sizing Table Methodology 8.3 Shutoff Valves, Regulators, and Drips 8.4 Gas Appliance Connections and Flexible Connectors 8.5 Gas Piping Inspection, Testing, and Purging

4.3 Duct Insulation Materials and Under-Floor Plenums (IRC M1601.3 and M1601.5)

Key Takeaways Explain This Topic AI

M1601.2 governs vibration isolators; M1601.3 governs duct insulation material properties and labeling.

2024 IRC M1601.3 generally limits duct covering/lining flame spread to 25 and smoke-developed index to 50, subject to its stated spray-foam exception.

Use the applicable energy provisions and the product's installed thickness to verify a required duct R-value; M1601.3 alone is not a universal R-6/R-8 table.

M1601.5 prohibits under-floor plenums in new structures; repairs or modifications to existing ones must meet its conditions.

For an existing under-floor plenum, M1601.5.1 requires a moisture barrier of at least 4 mils; M1601.5.5 addresses the furnace fan and outlet-air temperature controls.

Last updated: September 2026

Separate material rules from thermal R-value rules

The 2024 IRC places vibration isolators in M1601.2 and duct insulation materials in M1601.3 . M1601.3 addresses how duct coverings and linings perform in fire and how products are labeled. As a general rule, coverings and linings, including adhesives, must have a flame-spread index no higher than 25 and smoke-developed index no higher than 50 under the stated test methods. The section contains a distinct exception for spray polyurethane foam on exterior ducts in attics and crawl spaces; apply all conditions of that exception rather than the general 25/50 pair alone.

External insulation and factory-insulated flexible ducts must display manufacturer, installed-thickness R-value, and fire-index information at the intervals in M1601.3. Compression changes installed thickness; the code specifies how thickness is determined for ductwrap, duct board, flexible ducts, and spray foam. To decide how much insulation a particular duct requires, check the applicable 2024 IRC energy provisions and approved design for the duct's location and climate. Do not cite M1601.2 as an R-value rule or assume a single R-6/R-8 threshold fits every location.

Under-floor plenums: M1601.5

An under-floor plenum uses the space below a floor as an air pathway. M1601.5 prohibits it in a new structure. Modification or repair of an existing plenum may continue only under that section's conditions. M1601.5.1 calls for removal of loose combustibles and scrap, a tightly enclosed space, and a ground moisture barrier at least 4 mils thick. Plumbing waste cleanouts are restricted, subject to the code's stated exception. M1601.5.3 governs the furnace supply duct and noncombustible receptacles; M1601.5.4 requires a floor access opening; M1601.5.5 requires fan and outlet-air temperature controls. The latter limits outlet air to 200°F ; it is not a rule to shut off fuel precisely when plenum air exceeds 200°F.

Inspection sequence

Identify whether the plenum is new or an existing system being repaired. Check its enclosure, moisture barrier, fire properties, furnace connections, access, and controls against the actual M1601.5 text. For conventional insulated ducts, inspect the product listing and installed insulation separately from energy-code R-value compliance.

Loading diagram... 2024 IRC duct insulation and under-floor plenum checks