Study guide
1.1 S1 Exam Modules, Approved References & Code Editions
ICC Structural Steel and Bolting Special Inspector S1
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Special Inspection Roles, Responsibilities & Reporting
1.1 S1 Exam Modules, Approved References & Code Editions 1.2 Special Inspector Duties, Authority & Code Framework 1.3 Statement of Special Inspections, Approved Agencies & IBC Requirements 1.4 Discrepancy Notification & Non-Conformance Resolution 1.5 Daily, Progress & Final Special Inspection Reports
2 Chapter 2: Structural Steel Materials & Mill Verification
2.1 Structural Steel Shapes, Grades & ASTM Specifications 2.2 Mill Test Reports (MTRs) & Heat Traceability 2.3 Material Condition, Sampling & Visual Examination
3 Chapter 3: High-Strength Fasteners, Specifications & Joint Mechanics
3.1 ASTM F3125 Fastener Grades & Head Markings 3.2 Compatible Nuts, Washers & Coating Requirements 3.3 Bolted Joint Classifications: Snug-Tight, Pretensioned & Slip-Critical
4 Chapter 4: Pre-Installation Verification & Faying Surfaces
4.1 Pre-Installation Verification Testing 4.2 Faying Surface Preparation & Inspection 4.3 Bolt Holes, Clearances & Washer Requirements
5 Chapter 5: High-Strength Bolting Installation Methods
5.1 Turn-of-Nut Installation Method 5.2 Calibrated Wrench Installation Method 5.3 Twist-Off Tension-Control (TC) Bolt Installation 5.4 Direct Tension Indicator (DTI) Installation
6 Chapter 6: Bolting Inspection, Rejection & Torque Arbitration
6.1 Visual Inspection & Verification of Bolted Assemblies 6.2 Torque Arbitration Procedure 6.3 Fastener Rejection, Reuse Rules & Field Modifications
7 Chapter 7: Steel Framing Observation, Erection & Base Plates
7.1 AISC 303 Erection Tolerances & Plumbness 7.2 Column Base Plates & Anchor Rod Inspection 7.3 Base Plate Grouting & Bearing Support
8 Chapter 8: Structural Drawings, Notes & Schedules
8.1 Structural General Notes & Specification Interpretation 8.2 Framing Plans, Grid Systems & Member Marks 8.3 Column & Beam Schedules
9 Chapter 9: Connection Details, Bolt Schedules & Plan Callouts
9.1 Shear & Moment Connection Plan Interpretation 9.2 Bolted Joint Callouts, Bolt Sizes & Quantities on Drawings 9.3 Hole Types, Dimensions, Spacing & Edge Distance Verification
10 Chapter 10: Framing Geometry, Bracing & Base Plate Plan Details
10.1 Column Orientation, Splices & Stiffeners on Plans 10.2 Vertical & Horizontal Bracing Details on Plans 10.3 Base Plate Details, Anchor Rod Patterns & Grout Callouts on Plans 10.4 Comprehensive Plan Reading Scenarios & Defect Recognition
1.1 S1 Exam Modules, Approved References & Code Editions
Key Takeaways Explain This Topic AI
The S1 credential requires S1C (60 questions, 2 hours, open book) and S1P (30 questions, 1.5 hours, closed book), plus GR or an active ICC Special Inspector certification.
GR has 25 open-book questions in 1 hour and uses the 2021 or 2024 IBC with the 2021 Special Inspection Manual.
The only approved S1C reference is the AISC Steel Construction Manual, 14th or 15th Edition; its Part 16 contains AISC 360, the RCSC Specification and AISC 303.
The 14th Edition contains AISC 360-10, RCSC 2009 and AISC 303-10; the 15th Edition contains AISC 360-16, RCSC 2014 and AISC 303-16.
S1P supplies an electronic plan with each item, and ICC permits no additional references during PRONTO administration.
Last updated: October 2026
Why the Module Structure Matters
The ICC Structural Steel and Bolting Special Inspector (S1) certification is not one exam. ICC delivers it as separate modules, and each module has its own question count, time limit, book policy and content outline. A candidate who studies S1 as a single subject usually over-prepares for code lookups and under-prepares for the closed-book plan module, or the reverse. This section sets out the structure so the rest of the guide can be read against it.
The Three Modules
ICC's exam catalog lists these requirements for the Structural Steel and Bolting Special Inspector certification:
Pass GR – Special Inspector General Requirements , or hold an active ICC Special Inspector certification.
Pass S1C – Structural Steel and Bolting Codes .
Pass S1P – Structural Steel and Bolting Plans .
Module Questions Time Book policy Approved reference(s) Catalog fee (checked 2026-10-03)
GR 25 1 hour Open book 2021 or 2024 International Building Code, plus the Special Inspection Manual (2021 Edition) $85
S1C 60 2 hours Open book AISC Steel Construction Manual , 14th or 15th Edition $210
S1P 30 1.5 hours Closed book Electronic plans supplied with each item; no other references during PRONTO administration $210
All three modules are offered through PRONTO (remote online proctoring or in-person testing). ICC National Certification exams use a scaled passing score of 75. For S1C, the catalog adds that candidates may bring copyrighted, bound books, but not training materials such as presentations, study guides or practice questions, and that exam questions are based solely on the approved reference list.
Note
GR is a shared module. If you already hold an active ICC Special Inspector certification (for example, Reinforced Concrete), you take only S1C and S1P. S1 is also the prerequisite certification for the S2 Structural Welding special inspector path.
Official Content Outlines
Module Domain Weight What the outline asks you to verify
GR Duties and Responsibilities 60% Review approved plans and specifications for special inspection requirements; comply with the enforcing jurisdiction's special inspection requirements
GR Notification of Discrepancies 20% Notify the contractor of deviations; if uncorrected, notify the architect or engineer of record and the building official
GR Inspection Reports 20% Progress reports describing tests and compliance; a final summary report stating whether the work conformed
S1C Material Identification 17% Steel shapes and bolts are the type, size, grade and condition specified
S1C Material Sampling 13% Type, quantity, location and frequency of tests; identified samples; documentation and transport to the laboratory
S1C Bolts, Nuts and Washers 23% Correct type, size and location of bolts, holes, nuts and washers for the connection type; protected storage
S1C Pre-installation Verification 17% Faying surfaces; bolt tension verification tests
S1C Installation, Testing and Inspection 25% Joint type, installation, and the approved method and sequence of tightening
S1C Orientation and Frame Member Sizes 3% Frame orientation, details and member sizes match the approved documents
S1C Base Plates 2% Configuration, hole size, grout clearance, grout placement and sampling, seating and fastening
- S1P Material Identification 17% The same task, answered from the supplied plans
- S1P Bolts, Nuts and Washers 17% The same task, answered from the supplied plans
- S1P Orientation and Frame Member Sizes 46% The same task, answered from the supplied plans
- S1P Base Plates 20% The same task, answered from the supplied plans
The S1C weights show where the code questions are: almost two-thirds of S1C is high-strength bolting. The S1P weights show the opposite emphasis: two-thirds of the plan module is framing orientation, member sizes and base plates.
What Is Inside the Approved Manual
The S1C reference is the AISC Steel Construction Manual , and the standards you need are bound into its Part 16:
- Manual part Content 14th Edition 15th Edition
- 16.1 AISC 360, Specification for Structural Steel Buildings AISC 360-10 AISC 360-16
16.2 RCSC Specification for Structural Joints Using High-Strength Bolts December 31, 2009 edition August 1, 2014 edition (with April 2015 errata)
16.3 AISC 303, Code of Standard Practice for Steel Buildings and Bridges AISC 303-10 AISC 303-16
Other Manual parts you will use often are Part 1 (shape dimensions and properties), Part 2 (material specifications), Part 7 (bolt design aids and dimensions) and Part 14 (base plates, including Table 14-2 for anchor rod holes and plate washers).
Edition Differences That Change Answers
Because ICC accepts either edition, learn the values that differ. Later sections give the detail.
Topic 14th Edition (AISC 360-10 / RCSC 2009 / AISC 303-10) 15th Edition (AISC 360-16 / RCSC 2014 / AISC 303-16)
Turn-of-nut rotation tolerance ±30° for rotations of 1/2 turn and less; ±45° for 2/3 turn and more +60°, −30° for all required rotations (RCSC 2014 Table 8.2)
Standard hole for a 1 in. bolt 1-1/16 in. (d + 1/16) 1-1/8 in. in AISC 360-16 Table J3.3 (d + 1/8 for 1 in. and larger); RCSC 2014 Table 3.1 still lists 1-1/16 in.
Group A minimum pretension, 1-1/8 in. bolt 56 kips 64 kips in AISC 360-16 Table J3.1; RCSC 2014 Table 8.1 still lists 56 kips
Roughened hot-dip galvanized faying surface RCSC 2009: Class C, μ = 0.35 (AISC 360-10 treats it as Class A) Class A, μ = 0.30
Bolt material names ASTM A325, A490, F1852, F2280 ASTM F3125 Grades A325, A490, F1852 and F2280 in AISC 360-16
Anchor rod setting tolerances Spacing tolerances within and between rod groups (AISC 303-10 Section 7.5.1) Horizontal tolerance by rod diameter plus ±1/2 in. top elevation (AISC 303-16 Section 7.5.1)
Newer documents exist—RCSC published 2020 and 2025 editions, and AISC has issued AISC 360-22—but the S1C approved reference is the 14th or 15th Edition Manual. Where this guide mentions a newer rule, it labels it as a later edition.
Study Strategy by Module
GR: Tab IBC Chapter 17 (Sections 1703 through 1705) and Chapter 1 (Sections 102 through 104), and learn where the report and discrepancy language sits.
S1C: Tab Manual Part 16.2 (RCSC Sections 2 through 10) and Part 16.1 (AISC 360 Chapters J, M and N). Know the RCSC table numbers: Table 2.1 (nut and washer compatibility), Table 3.1 (holes), Table 6.1 (washers), Table 7.1 (pre-installation pretension), Table 8.1 (minimum pretension) and Table 8.2 (turn-of-nut rotation).
S1P: Practice extracting member sizes, grid locations, bolt callouts, hole types and base plate data from drawings without any reference, because none is allowed.