Study guide

3.4 Conduit Fill Calculations & Large Pull Box Sizing (NEC 314.28)

Idaho Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation, NEC Navigation & Idaho Regulations

1.1 Idaho Journeyman Exam Format, PSI Logistics & Rapid NEC Navigation 1.2 Idaho Electrical Licensing Laws (Title 54, Ch. 10) & IDAPA 24.39.10 Requirements 1.3 Idaho Permits, Inspection Procedures & State-Specific NEC Amendments 1.4 NEC Article 90 Scope, Code Arrangement & Article 110 General Requirements

2 Chapter 2: Electrical Theory & Essential Math Calculations

2.1 Ohm's Law, Joule's Law & DC Circuit Calculations 2.2 Single-Phase & Three-Phase AC Fundamentals and Power Factor 2.3 DC & AC Voltage Drop Calculations and Conductor Sizing 2.4 NEC Article 100 Essential Definitions for Journeymen

3 Chapter 3: Conductors, Raceways & Box Sizing Calculations

3.1 Conductor Ampacity, Insulation Types & Terminal Temperature Ratings 3.2 Ambient Temperature Correction & Raceway Conductor Bundling Derating 3.3 Outlet & Junction Box Volume Fill Calculations (NEC 314.16) 3.4 Conduit Fill Calculations & Large Pull Box Sizing (NEC 314.28)

4 Chapter 4: Branch Circuits & Overcurrent Protection

4.1 Branch Circuit Ratings, Multiwire Circuits & Receptacle Placement 4.2 GFCI & AFCI Protection Mandates and Idaho Code Clarifications 4.3 Overcurrent Protective Devices, Standard Ratings & Small Conductor Rules 4.4 Feeder & Transformer Tap Rules (NEC 240.21)

5 Chapter 5: Feeders, Services & Outside Branch Circuits

5.1 Feeder Conductor Sizing, Neutral Calculations & Voltage Drop 5.2 Outside Branch Circuits, Feeders & Overhead/Underground Clearances 5.3 Service Drop, Service Lateral & Service-Entrance Sizing 5.4 Service Disconnecting Means, Emergency Disconnects & Surge Protection

6 Chapter 6: Load Calculations: Dwellings & Commercial

6.1 General Lighting, Small Appliance & Laundry Load Calculations 6.2 Standard Method Single-Family Dwelling Service Calculations (NEC 220 Part III) 6.3 Optional Method Single-Family & Multifamily Calculations (NEC 220 Part IV) 6.4 Commercial & Industrial Feeder/Service Calculations

7 Chapter 7: Grounding and Bonding: Systems & Electrodes

7.1 Grounding vs. Bonding Fundamentals & System Grounding 7.2 Grounding Electrodes & Grounding Electrode Conductor (GEC) Sizing 7.3 Main Bonding Jumpers, System Bonding Jumpers & Supply-Side Bonding

8 Chapter 8: Grounding and Bonding: Equipment & Enclosures

8.1 Equipment Grounding Conductors (EGC) Types, Installation & Sizing (Table 250.122) 8.2 Separately Derived Systems (SDS) Transformers & Generator Grounding 8.3 Service Enclosure Bonding, Concentric Knockouts & Effective Ground-Fault Path

9 Chapter 9: Wiring Methods, Cables & Conduits

9.1 General Requirements for Wiring Methods & Underground Installations (Article 300) 9.2 Nonmetallic-Sheathed (NM), Metal-Clad (MC) & Armored (AC) Cables 9.3 Metallic & Nonmetallic Raceway Systems (EMT, PVC, RMC, FMC) 9.4 Cabinets, Cutout Boxes & Outlet Box Installation Rules (Articles 312 & 314)

10 Chapter 10: Equipment for General Use: Devices, Luminaires & Appliances

10.1 Switches, Receptacles & Device Installation Standards (Articles 404 & 406) 10.2 Luminaire Clearances, Closet Rules & Lighting Track (Article 410) 10.3 Household Appliances & Fixed Electric Space Heating (Articles 422 & 424) 10.4 Generators, Transformer Overcurrent Protection & Panelboards

11 Chapter 11: Motors, Motor Circuits & Controllers

11.1 Motor Nameplate vs. Table FLC & Branch Circuit Conductor Sizing 11.2 Branch Circuit Short-Circuit & Ground-Fault Protection (Table 430.52) 11.3 Motor Overload Protection Sizing & Selection (NEC 430 Part III) 11.4 Motor Disconnects, Controllers & Multimotor Feeder Calculations

12 Chapter 12: Special Occupancies & Hazardous Locations

12.1 Hazardous (Classified) Locations: Classes, Divisions, Zones & Seals 12.2 Commercial Garages, Repair Hangars & Fuel Dispensing Facilities 12.3 Health Care Facilities: Patient Care Spaces & Redundant Grounding (Article 517) 12.4 Agricultural Buildings, Marinas, Boatyards & RV Parks

13 Chapter 13: Special Equipment, Emergency Systems & Renewable Energy

13.1 Swimming Pools, Spas, Hot Tubs & Equipotential Bonding (Article 680) 13.2 Electric Vehicle Supply Equipment (EVSE) Installation & Sizing (Article 625) 13.3 Solar Photovoltaic (PV) Systems & Energy Storage Systems (Articles 690 & 706) 13.4 Emergency, Standby Power Systems & Fire Pumps (Articles 700, 701, 702 & 695) 13.5 Fire Alarm, Optical Fiber & Power-Limited Circuits (Articles 760, 770 & 800)

3.4 Conduit Fill Calculations & Large Pull Box Sizing (NEC 314.28)

Key Takeaways Explain This Topic AI

Conduit fill limitations under NEC Chapter 9, Table 1 permit a maximum fill of 53% for 1 conductor, 31% for 2 conductors, and 40% for 3 or more conductors.

Short conduit nipples 24 inches or less in length between enclosures are permitted a maximum fill of 60% under Chapter 9, Table 1, Note 4, and do not require ampacity derating.

For mixed wire sizes in a raceway, total conductor cross-sectional areas from Chapter 9, Table 5 are summed, and a conduit size is selected where the 40% usable internal area from Chapter 9, Table 4 is equal to or greater than the total wire area.

Under NEC 314.28(A)(1), straight pull boxes for conductors 4 AWG and larger must have a minimum box length not less than 8 times the trade size of the largest entering raceway.

Under NEC 314.28(A)(2), angle and U-pull boxes must have a distance to the opposite wall not less than 6 times the trade size of the largest raceway plus the sum of all other raceways on that wall, with a minimum distance between raceway entries containing the same conductor of 6 times the trade size.

Last updated: August 2026

Conduit Fill Calculations & Large Pull Box Sizing (NEC 314.28)

Pulling conductors through raceway systems and sizing commercial enclosures requires strict compliance with physical geometry rules. Sizing raceways ensures that conductors can be installed without excessive pulling tension, jamming, or insulation shearing. Sizing large junction and pull boxes guarantees that heavy conductors (4 AWG and larger) can be trained and bent without violating minimum conductor bending radii.

In the National Electrical Code, raceway fill is governed by Chapter 9 Tables , while pull and junction boxes housing conductors 4 AWG and larger are governed by NEC 314.28 .

1. NEC Chapter 9 Raceway Fill Rules

Table 1: Percent of Cross Section of Conduit and Tubing for Conductors +-----------------------------------------------------------------------------+

  • | NEC CHAPTER 9, TABLE 1 PERCENT FILL RULES |
  • | |
  • | [1 CONDUCTOR] ---> 53% Maximum Fill |
  • | [2 CONDUCTORS] ---> 31% Maximum Fill (Accounts for jamming effect) |
  • | [3+ CONDUCTORS] ---> 40% Maximum Fill (Standard commercial rule) |
  • | |
  • | [NIPPLES <= 24 INCHES] ---> 60% Maximum Fill (Chapter 9, Note 4) |
  • +-----------------------------------------------------------------------------+

1 Conductor (53%): Permitted higher fill because a single cylindrical conductor pulls smoothly along the conduit centerline without jamming.

2 Conductors (31%): Restricted to the lowest fill percentage because two round conductors in a round pipe tend to twist into an oval profile, causing severe sidewall friction and jamming.

3 or More Conductors (40%): The standard design fill for general electrical raceways.

Conduit Nipples <= 24 inches (60%): Under Chapter 9, Table 1, Note 4 , raceways not exceeding 24 in. (600 mm) installed between boxes, cabinets, or enclosures may be filled up to 60% of their total internal area.

Multiconductor Cables (Note 9): A multiconductor cable containing two or more conductors is treated as a single conductor for conduit fill calculations based on its overall outer diameter.

  • 2. Chapter 9, Tables 4 & 5 Reference Data
  • Table 4: Usable Internal Area of Raceways (Selected Trade Sizes in sq in)

Trade Size EMT Total Area (100%) EMT 40% Area EMT 60% Area PVC Sch 40 40% Area PVC Sch 80 40% Area RMC 40% Area

  • 1/2" 0.304 0.122 0.182 0.114 0.087 0.125
  • 3/4" 0.533 0.213 0.320 0.203 0.164 0.220
  • 1" 0.864 0.346 0.519 0.333 0.275 0.355
  • 1-1/4" 1.496 0.598 0.897 0.581 0.495 0.610
  • 1-1/2" 2.036 0.814 1.221 0.794 0.684 0.829
  • 2" 3.356 1.342 2.013 1.316 1.150 1.363
  • 2-1/2" 5.858 2.343 3.515 1.878 1.647 1.946
  • 3" 8.846 3.538 5.307 2.907 2.577 3.000
  • 3-1/2" 11.545 4.618 6.927 3.895 3.475 4.004
  • 4" 14.753 5.901 8.852 5.022 4.503 5.153

Warning

PVC Schedule 40 vs. Schedule 80: PVC Schedule 80 has a much thicker pipe wall to withstand severe physical damage. Consequently, its internal diameter and 40% usable area are significantly smaller than Schedule 40. Always check the specific raceway column in Table 4!

Note also that above 2-inch trade size, RMC is no longer the roomiest raceway — at 2-1/2 in. and larger, EMT has a materially greater 40% area (2.343 in² vs. 1.946 in² at 2-1/2 in.). Do not assume the raceway type from the trade size alone; look up the specific column every time.

Table 5: Dimensions and Areas of Insulated Conductors (THHN / THWN-2)

  • Conductor Size THHN / THWN-2 Area (sq in) XHHW-2 Area (sq in) RHW-2 Area (sq in)
  • 14 AWG 0.0097 0.0139 0.0293
  • 12 AWG 0.0133 0.0181 0.0353
  • 10 AWG 0.0211 0.0243 0.0437
  • 8 AWG 0.0366 0.0437 0.0707
  • 6 AWG 0.0507 0.0590 0.0881
  • 4 AWG 0.0824 0.0814 0.1333
  • 3 AWG 0.0973 0.0962 0.1521
  • 2 AWG 0.1158 0.1146 0.1750
  • 1 AWG 0.1562 0.1534 0.2223
  • 1/0 AWG 0.1855 0.1825 0.2552
  • 2/0 AWG 0.2223 0.2190 0.2971
  • 3/0 AWG 0.2679 0.2642 0.3473
  • 4/0 AWG 0.3237 0.3197 0.4072
  • 250 kcmil 0.3970 0.3904 0.5052
  • 350 kcmil 0.5242 0.5165 0.6461
  • 500 kcmil 0.7073 0.6984 0.8495
  • 3. Mixed Conductor Conduit Fill Calculation Workflow

When a raceway contains identical conductors, the electrician may look up the raceway size directly in NEC Informative Annex C . However, when a raceway contains a combination of different wire gauges, the cross-sectional areas must be calculated manually: +-----------------------------------------------------------------------------+

  • | MIXED CONDUIT FILL STEP-BY-STEP WORKFLOW |
  • | |
  • | [STEP 1] Find individual wire areas from Table 5. |
  • | [STEP 2] Multiply each wire area by the quantity of that conductor size. |
  • | [STEP 3] Sum all conductor areas: Total Area = Sum(A_i x Qty_i). |
  • | [STEP 4] Compare Total Area to Table 4 (40% Column) for chosen raceway. |
  • | [STEP 5] Select smallest conduit size where Table 4 40% Area >= Total Area|
  • +-----------------------------------------------------------------------------+
  • Worked Example: Mixed Conductor Sizing in EMT

Problem: Determine the minimum trade size Electrical Metallic Tubing (EMT) required to enclose:

  • Three (3) 3/0 AWG THHN conductors
  • One (1) 1/0 AWG THHN conductor (neutral)
  • One (1) 4 AWG THHN conductor (equipment grounding conductor)

Solution:

Look up Table 5 areas for THHN:

  • 3/0 THHN: 0.2679 sq in
  • 1/0 THHN: 0.1855 sq in
  • 4 AWG THHN: 0.0824 sq in

Calculate subtotal areas:

  • Three 3/0 THHN: 3 x 0.2679 sq in = 0.8037 sq in
  • One 1/0 THHN: 1 x 0.1855 sq in = 0.1855 sq in
  • One 4 AWG THHN: 1 x 0.0824 sq in = 0.0824 sq in
  • Sum Total Conductor Area: Total Area = 0.8037 + 0.1855 + 0.0824 = 1.0716 sq in

Select Conduit from Table 4 (EMT 40% Column):

  • 1-1/2" EMT has a 40% area of 0.814 sq in (Too small, 0.814 < 1.0716)
  • 2" EMT has a 40% area of 1.342 in² (1.342 >= 1.0716)

Conclusion: Minimum size required is 2-inch EMT .

4. Pull & Junction Box Sizing (Conductors 4 AWG & Larger — NEC 314.28)

Boxes and conduit bodies containing conductors of size 4 AWG or larger (under 1000 volts) must comply with the physical dimensional standards of NEC 314.28 to ensure conductors can be pulled through and coiled without bending damage. +-----------------------------------------------------------------------------+

  • | NEC 314.28 PULL BOX SIZING FORMULA CHEAT SHEET |
  • | |
  • | [1. STRAIGHT PULLS (314.28(A)(1))] |
  • | - Box Length >= 8 x (Trade Size of Largest Raceway) |
  • | |
  • | [2. ANGLE PULLS & U-PULLS (314.28(A)(2))] |
  • | - Distance to Opposite Wall >= |
  • | [6 x (Largest Raceway Size)] + [Sum of All Other Raceways on Same Wall] |
  • | |
  • | [3. DISTANCE BETWEEN RACEWAY ENTRIES FOR SAME CONDUCTOR] |
  • | - Distance between Entry & Exit >= 6 x (Trade Size of Raceway) |
  • +-----------------------------------------------------------------------------+
  • 1. Straight Pulls (NEC 314.28(A)(1))

Where conductors are pulled in a straight line from one side of the box through to the opposite side:

The length of the box must not be less than 8 times the trade size of the largest raceway entering the box:

  • Length >= 8 x Trade Size_largest +-------------------------------------------+
  • | |
  • [3" Conduit] ==> STRAIGHT PULL ==> [3" Conduit]
  • (Entry Wall) | | (Exit Wall)
  • +-------------------------------------------+
  • |<----------------- L --------------------->|
  • Minimum Length = 8 x 3" = 24 Inches
  • 2. Angle Pulls and U-Pulls (NEC 314.28(A)(2))

Where conductors enter on one wall and exit at a 90° angle on an adjacent wall (Angle Pull), or enter and exit on the same wall (U-Pull):

Distance to Opposite Wall: The distance between each raceway entry and the opposite wall must not be less than 6 times the trade size of the largest raceway , PLUS the sum of the trade sizes of all other raceways on that same wall:

Distance >= (6 x Trade Size_largest) + Sum Other Raceway Trade Sizes on Same Wall

Distance Between Conduit Entries for the Same Conductor: The center-to-center distance between the raceway entry and exit for conductors in the same circuit must not be less than 6 times the trade size of the raceway:

  • Distance Between Entries >= 6 x Trade Size Angle Pull Geometry
  • +----------------------------------+
  • | |
  • [3" Entry] =======>| |
  • [2" Entry] =======>| ANGLE PULL |
  • [2" Entry] =======>| |
  • (Left Wall) | |
  • +----------------------------------+
  • || ||
  • || ||
  • [3" Exit] [2" Exits]
  • (Bottom Wall)
  • Left-to-Right Distance = (6 x 3") + 2" + 2" = 18" + 4" = 22 Inches
  • Bottom-to-Top Distance = (6 x 3") + 2" + 2" = 18" + 4" = 22 Inches
  • Minimum Box Size = 22" Wide x 22" High
  • Center-to-Center 3" Run = 6 x 3" = 18 Inches minimum between 3" entries
  • Worked Example: Comprehensive Angle Pull Box Sizing

Problem: A junction box contains conductors 4 AWG and larger. The raceways entering the enclosure are:

Left Wall: One 4-inch conduit and two 2-inch conduits.

Bottom Wall: One 4-inch conduit and two 2-inch conduits (enclosing the same circuits).

What is the minimum required width, height, and depth of this pull box?

Step-by-Step Solution:

Calculate Distance from Left Wall to Right Wall (Box Width):

Largest conduit on left wall = 4 inches.

Other conduits on left wall = 2" + 2" = 4 inches.

Width = (6 x 4 in.) + 2 in. + 2 in. = 24 in. + 4 in. = 28 Inches .

Calculate Distance from Bottom Wall to Top Wall (Box Height):

Largest conduit on bottom wall = 4 inches.

Other conduits on bottom wall = 2" + 2" = 4 inches.

Height = (6 x 4 in.) + 2 in. + 2 in. = 24 in. + 4 in. = 28 Inches .

Minimum Distance Between 4-Inch Entries (Corner Distance):

Distance = 6 x 4 in. = 24 Inches center-to-center.

Box Depth: Must be sufficient to allow locknuts, insulating bushings, and provide standard clearance (typically 6" to 8").

Conclusion: Minimum enclosure dimensions are 28" × 28" × 6" .