Study guide

2.2 Single-Phase & Three-Phase AC Fundamentals and Power Factor

Idaho Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation, NEC Navigation & Idaho Regulations

1.1 Idaho Journeyman Exam Format, PSI Logistics & Rapid NEC Navigation 1.2 Idaho Electrical Licensing Laws (Title 54, Ch. 10) & IDAPA 24.39.10 Requirements 1.3 Idaho Permits, Inspection Procedures & State-Specific NEC Amendments 1.4 NEC Article 90 Scope, Code Arrangement & Article 110 General Requirements

2 Chapter 2: Electrical Theory & Essential Math Calculations

2.1 Ohm's Law, Joule's Law & DC Circuit Calculations 2.2 Single-Phase & Three-Phase AC Fundamentals and Power Factor 2.3 DC & AC Voltage Drop Calculations and Conductor Sizing 2.4 NEC Article 100 Essential Definitions for Journeymen

3 Chapter 3: Conductors, Raceways & Box Sizing Calculations

3.1 Conductor Ampacity, Insulation Types & Terminal Temperature Ratings 3.2 Ambient Temperature Correction & Raceway Conductor Bundling Derating 3.3 Outlet & Junction Box Volume Fill Calculations (NEC 314.16) 3.4 Conduit Fill Calculations & Large Pull Box Sizing (NEC 314.28)

4 Chapter 4: Branch Circuits & Overcurrent Protection

4.1 Branch Circuit Ratings, Multiwire Circuits & Receptacle Placement 4.2 GFCI & AFCI Protection Mandates and Idaho Code Clarifications 4.3 Overcurrent Protective Devices, Standard Ratings & Small Conductor Rules 4.4 Feeder & Transformer Tap Rules (NEC 240.21)

5 Chapter 5: Feeders, Services & Outside Branch Circuits

5.1 Feeder Conductor Sizing, Neutral Calculations & Voltage Drop 5.2 Outside Branch Circuits, Feeders & Overhead/Underground Clearances 5.3 Service Drop, Service Lateral & Service-Entrance Sizing 5.4 Service Disconnecting Means, Emergency Disconnects & Surge Protection

6 Chapter 6: Load Calculations: Dwellings & Commercial

6.1 General Lighting, Small Appliance & Laundry Load Calculations 6.2 Standard Method Single-Family Dwelling Service Calculations (NEC 220 Part III) 6.3 Optional Method Single-Family & Multifamily Calculations (NEC 220 Part IV) 6.4 Commercial & Industrial Feeder/Service Calculations

7 Chapter 7: Grounding and Bonding: Systems & Electrodes

7.1 Grounding vs. Bonding Fundamentals & System Grounding 7.2 Grounding Electrodes & Grounding Electrode Conductor (GEC) Sizing 7.3 Main Bonding Jumpers, System Bonding Jumpers & Supply-Side Bonding

8 Chapter 8: Grounding and Bonding: Equipment & Enclosures

8.1 Equipment Grounding Conductors (EGC) Types, Installation & Sizing (Table 250.122) 8.2 Separately Derived Systems (SDS) Transformers & Generator Grounding 8.3 Service Enclosure Bonding, Concentric Knockouts & Effective Ground-Fault Path

9 Chapter 9: Wiring Methods, Cables & Conduits

9.1 General Requirements for Wiring Methods & Underground Installations (Article 300) 9.2 Nonmetallic-Sheathed (NM), Metal-Clad (MC) & Armored (AC) Cables 9.3 Metallic & Nonmetallic Raceway Systems (EMT, PVC, RMC, FMC) 9.4 Cabinets, Cutout Boxes & Outlet Box Installation Rules (Articles 312 & 314)

10 Chapter 10: Equipment for General Use: Devices, Luminaires & Appliances

10.1 Switches, Receptacles & Device Installation Standards (Articles 404 & 406) 10.2 Luminaire Clearances, Closet Rules & Lighting Track (Article 410) 10.3 Household Appliances & Fixed Electric Space Heating (Articles 422 & 424) 10.4 Generators, Transformer Overcurrent Protection & Panelboards

11 Chapter 11: Motors, Motor Circuits & Controllers

11.1 Motor Nameplate vs. Table FLC & Branch Circuit Conductor Sizing 11.2 Branch Circuit Short-Circuit & Ground-Fault Protection (Table 430.52) 11.3 Motor Overload Protection Sizing & Selection (NEC 430 Part III) 11.4 Motor Disconnects, Controllers & Multimotor Feeder Calculations

12 Chapter 12: Special Occupancies & Hazardous Locations

12.1 Hazardous (Classified) Locations: Classes, Divisions, Zones & Seals 12.2 Commercial Garages, Repair Hangars & Fuel Dispensing Facilities 12.3 Health Care Facilities: Patient Care Spaces & Redundant Grounding (Article 517) 12.4 Agricultural Buildings, Marinas, Boatyards & RV Parks

13 Chapter 13: Special Equipment, Emergency Systems & Renewable Energy

13.1 Swimming Pools, Spas, Hot Tubs & Equipotential Bonding (Article 680) 13.2 Electric Vehicle Supply Equipment (EVSE) Installation & Sizing (Article 625) 13.3 Solar Photovoltaic (PV) Systems & Energy Storage Systems (Articles 690 & 706) 13.4 Emergency, Standby Power Systems & Fire Pumps (Articles 700, 701, 702 & 695) 13.5 Fire Alarm, Optical Fiber & Power-Limited Circuits (Articles 760, 770 & 800)

2.2 Single-Phase & Three-Phase AC Fundamentals and Power Factor

Key Takeaways Explain This Topic AI

AC sine wave characteristics: Root-Mean-Square (RMS) voltage represents the equivalent DC thermal heating value, where V_RMS = 0.707 * V_peak and V_peak = 1.414 * V_RMS. Multimeters and NEC ratings always express AC quantities in RMS.

AC impedance (Z) is the vector sum of pure resistance (R) and net reactance (X = X_L - X_C): Z = √(R² + (X_L - X_C)²). Inductive reactance (X_L = 2πfL) causes current to lag voltage, while capacitive reactance (X_C = 1 / (2πfC)) causes current to lead voltage.

Power Factor (PF) is the ratio of True Power (P in watts) to Apparent Power (S in VA): PF = W / VA = cos(θ). Inductive motor loads create lagging power factors that draw excess line current without producing mechanical work.

In balanced 3-phase Wye systems, Line-to-Line voltage is √3 (1.732) times Line-to-Neutral voltage (V_LL = 1.732 * V_LN), while Line current equals Phase current (I_Line = I_Phase). Standard configurations include 208Y/120V and 480Y/277V.

In balanced 3-phase Delta systems, Line voltage equals Phase voltage (V_LL = V_Phase), while Line current is √3 times Phase current (I_Line = 1.732 * I_Phase). Three-phase apparent power is always calculated as VA = √3 * E_LL * I_Line.

Last updated: August 2026

2.2 Single-Phase & Three-Phase AC Fundamentals and Power Factor

Alternating current (AC) is the universal medium for electrical power transmission and distribution. Unlike direct current, AC periodically reverses its direction of flow and continuously changes its magnitude. This sinusoidal behavior introduces reactive components—inductance and capacitance—that shift the timing relationship between voltage and current waveforms.

For the Idaho Journeyman exam, you must master the mathematical relationships of single-phase and three-phase circuits, understand the square root of three (1.732 ≈ 1.732) conversion factor, and solve complex power factor problems.

1. AC Sine Wave Metrics & Principles

A pure AC voltage wave is generated by a conductor rotating through a uniform magnetic field, producing a sinusoidal waveform described by the function e(t) = V_peak sin(2π f t). +-----------------------------------------------------------------------------+

  • | AC SINE WAVE CHARACTERISTICS |
  • | |
  • | +V_peak --+ * * * |
  • | | * * |
  • | +V_RMS --+ - - * - - - - - * - - - - - - - - - - - - - |
  • | | * * |
  • | 0 Volts --+---*---------------+---------------*----------> Time |
  • | | * * |
  • | -V_RMS --+ - - - - - - - - - - * - - - - - * - - - - - |
  • | | * * |
  • | -V_peak --+ * * * |
  • | |<------------- 1 Cycle (360°) ------------->| |
  • +-----------------------------------------------------------------------------+
  • Core Waveform Definitions

Frequency (f): The number of complete cycles (360^°) executed per second, measured in Hertz (Hz). North American electrical systems operate at standard 60 Hz .

Period (T): The time required to complete one full cycle: T = 1 / f. At 60 Hz, T = 1 / 60 = 0.01667 seconds = 16.67 ms.

Peak Voltage (V_peak): The maximum instantaneous voltage reached in either the positive or negative half-cycle.

Peak-to-Peak Voltage (V_pk-pk): The total amplitude between positive and negative peaks: V_pk-pk = 2 x V_peak.

RMS (Root-Mean-Square) Effective Voltage (V_RMS): The effective value of an AC voltage that delivers the exact same heating power to a resistive load as an equivalent DC voltage.

V_RMS = V_peak x 0.7071 = V_peak / sqrt(2) V_peak = V_RMS x 1.4142 = V_RMS x sqrt(2) V_average = V_peak x 0.637

Note

Unless explicitly stated otherwise, every voltage and current specified on nameplates, test instruments, blueprints, and the NEC is an RMS value . A nominal 120 V receptacle actually swings between +169.7 V and -169.7 V peak (120 x 1.4142).

2. Reactance & Impedance in AC Circuits

When AC flows through coils (motors, transformers, ballasts) or capacitors, the changing electromagnetic and electrostatic fields create an opposition to current flow known as reactance (X) . +-----------------------------------------------------------------------------+

  • | REACTANCE & PHASE ANGLE MNEMONICS |
  • | |
  • | " E L I " " I C E " |
  • | In an Inductive Circuit: In a Capacitive Circuit: |
  • | Voltage (E) Leads Current (I) Current (I) Leads Voltage (E) |
  • | Current (I) LAGS Voltage (E) Voltage (E) LAGS Current (I) |
  • +-----------------------------------------------------------------------------+
  • Inductive Reactance (X_L)

Inductors (wire coils) oppose changes in current by generating a counter-electromotive force (CEMF). Inductive reactance is directly proportional to frequency and inductance (L in Henrys):

  • X_L = 2 π f L
  • Capacitive Reactance (X_C)

Capacitors store electrostatic charge and oppose changes in voltage. Capacitive reactance is inversely proportional to frequency and capacitance (C in Farads):

  • X_C = (1) / (2 π f C)
  • Total Impedance (Z)

Impedance (Z) is the total opposition to AC current flow, combining pure DC resistance (R) and net reactance (X = X_L - X_C). Because resistance and reactance are 90^° out of phase, they must be added vectorially using the Pythagorean theorem:

Z = sqrt(R^2 + (X_L - X_C)^2) Impedance Triangle (Vector Addition)

  • /|
  • / |
  • / |
  • Impedance / | Net Reactance
  • (Z)/ | (X = X_L - X_C)
  • / |
  • / θ |
  • +-------+
  • Resistance (R)
  • Worked Example: AC Impedance and Current

An industrial motor coil has a winding resistance of 8 Ω and an inductance of 0.0159 H. It is connected to a 120 V, 60 Hz supply. Calculate the inductive reactance, circuit impedance, and current.

  • Calculate Inductive Reactance (X_L): X_L = 2 x π x 60 Hz x 0.0159 H = 377 x 0.0159 ≈ 6.0 Ω
  • Calculate Total Impedance (Z): Z = sqrt(R^2 + X_L^2) = sqrt(8^2 + 6^2) = sqrt(64 + 36) = sqrt(100) = 10.0 Ω
  • Calculate Circuit Current (I): I = E / Z = (120 V) / (10.0 Ω) = 12.0 A
  • 3. The Power Triangle & Power Factor

In AC circuits with reactive components, power is divided into three distinct vector components forming the Power Triangle : +-----------------------------------------------------------------------------+

  • | THE POWER TRIANGLE |
  • | |
  • | Apparent Power (S) in Volt-Amperes (VA) |
  • | /| |
  • | / | |
  • | / | Reactive Power (Q) |
  • | / | in VARs (kVAR) |
  • | / | (Magnetizing Current) |
  • | / θ | |
  • | +------+ |
  • | True Power (P) in Watts (kW) |
  • | (Actual Work / Thermal Heat) |
  • +-----------------------------------------------------------------------------+

Power Component Definitions:

True Power (P): Measured in Watts (W) or Kilowatts (kW) . Represents the actual energy consumed to perform mechanical work or produce heat: P = E x I x cos(θ) = I^2 x R.

Reactive Power (Q): Measured in Volt-Amperes Reactive (VAR) or kVAR . Power alternately stored and returned to the circuit by inductive magnetic fields: Q = E x I x sin(θ) = I^2 x X.

Apparent Power (S): Measured in Volt-Amperes (VA) or kVA . The total vector combination of True and Reactive power supplied by the utility: S = E x I = sqrt(P^2 + Q^2).

Power Factor (PF)

Power factor is the mathematical ratio of True Power to Apparent Power:

PF = (True Power (W)) / (Apparent Power (VA)) = cos(θ) True Power (Watts) = Apparent Power (VA) x PF = E x I x PF

Warning

Why Low Power Factor Matters: An inductive motor operating at a 0.70 power factor requires 1.43 times more line current (1 / 0.70) than a unity-PF load doing the same mechanical work. This excess current increases I^2R thermal line losses, drops branch-circuit voltage, and causes utilities to levy steep power factor surcharge penalties.

4. Three-Phase AC Principles: Wye vs. Delta Systems

Three-phase AC power is generated by three separate coils spaced 120^° apart mechanically within the alternator stator, producing three sinusoidal voltages of equal magnitude shifted by 120^° in phase. +-----------------------------------------------------------------------------+

  • | THREE-PHASE SYSTEM ARCHITECTURES |
  • | |
  • | WYE (STAR) CONNECTION DELTA CONNECTION |
  • | |
  • | Phase A Phase A |
  • | o o |
  • | \ / \ |
  • | \ Phase B / \ |
  • | Neutral o--o---o / \ |
  • | / o-------o |
  • | / Phase B Phase C |
  • | o |
  • | Phase C |
  • +-----------------------------------------------------------------------------+
  • The 1.732 (1.732) Geometric Relationship

Because phases are separated by 120^° rather than 180^°, line-to-line voltages do not equal 2 x V_phase. Instead, vector subtraction yields the fundamental multiplier:

  • 1.732 = 2 x cos(30^°) = 2 x 0.866025 = 1.73205
  • Summary of 3-Phase Rules

Property Wye (Y) 4-Wire System Delta (Δ) 3-Wire System High-Leg Delta 4-Wire

Voltage Relation V_Line-Line = 1.732 x V_Line-Neutral V_Line-Line = V_Phase Phase A & C to N = 120 V;; Phase B (High-Leg) to N = 208 V

  • Current Relation I_Line = I_Phase I_Line = 1.732 x I_Phase Standard branch rules apply
  • Standard Voltages 208Y/120V, 480Y/277V 240V, 480V 240/120V (NEC 110.15 High-Leg)

Common Use Commercial lighting, receptacles, motors Heavy industrial plants, ungrounded/corner-grounded Light commercial with heavy 240V 3-phase motor loads

Caution

NEC 110.15 High-Leg Identification: On a 4-wire, delta-connected system where the midpoint of one phase winding is grounded to supply 120V lighting loads, the phase conductor with the higher voltage-to-ground (120V x 1.732 = 208V) must be identified by an outer finish that is ORANGE in color (or by tagging) and must be connected to Phase B in panelboards and switchboards.

5. Three-Phase Power Formulas & Worked Calculations

When calculating power in balanced three-phase systems, the formulas always incorporate the 1.732 ≈ 1.732 constant:

VA_Three-Phase = 1.732 x E_Line-Line x I_Line = 1.732 x E_LL x I_L P_Watts = 1.732 x E_Line-Line x I_Line x PF = 1.732 x E_LL x I_L x PF I_Line = (VA_Three-Phase) / (1.732 x E_Line-Line) = (P_Watts) / (1.732 x E_Line-Line x PF)

  • Comprehensive Step-by-Step 3-Phase Problems
  • Problem 2.1: Sizing a 3-Phase Transformer Secondary Feeder

A 75 kVA, 3-phase transformer has a 480V primary and a 208Y/120V secondary. Calculate the rated full-load line current output on the secondary side.

Given: VA = 75,000 VA, E_Line-Line = 208 V

I_Line = (VA) / (1.732 x E_LL) = (75,000) / (1.732 x 208) = 75,000 / 360.256 = 208.19 Amperes (A standard 208Y/120V 75 kVA transformer supplies approximately 208 A per phase at full load).

Problem 2.2: Sizing Feeders for a 3-Phase Industrial Motor

A 480 V, 3-phase, 50 HP induction motor operates at an efficiency of 91% and a lagging power factor of 0.86. Calculate the actual full-load line current drawn by the motor.

Step 1: Convert Output Mechanical Horsepower to Electrical Watts Input: P_output = 50 HP x 746 W/HP = 37,300 Watts

  • P_input = P_output / Efficiency = (37,300 W) / (0.91) = 40,989.0 Watts
  • Step 2: Calculate Apparent Power (VA): VA = P_input / PF = 40,989.0 / 0.86 = 47,661.6 VA

Step 3: Calculate Line Current (I_Line): I_Line = (VA) / (1.732 x E_LL) = (47,661.6) / (1.732 x 480) = 47,661.6 / 831.36 = 57.33 Amperes (Note: For NEC branch circuit sizing, electricians refer to NEC Table 430.250, which lists a standardized FLC of 65A for a 50HP 460V motor to ensure safety margins).