Study guide
2.3 DC & AC Voltage Drop Calculations and Conductor Sizing
Idaho Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Orientation, NEC Navigation & Idaho Regulations
1.1 Idaho Journeyman Exam Format, PSI Logistics & Rapid NEC Navigation 1.2 Idaho Electrical Licensing Laws (Title 54, Ch. 10) & IDAPA 24.39.10 Requirements 1.3 Idaho Permits, Inspection Procedures & State-Specific NEC Amendments 1.4 NEC Article 90 Scope, Code Arrangement & Article 110 General Requirements
2 Chapter 2: Electrical Theory & Essential Math Calculations
2.1 Ohm's Law, Joule's Law & DC Circuit Calculations 2.2 Single-Phase & Three-Phase AC Fundamentals and Power Factor 2.3 DC & AC Voltage Drop Calculations and Conductor Sizing 2.4 NEC Article 100 Essential Definitions for Journeymen
3 Chapter 3: Conductors, Raceways & Box Sizing Calculations
3.1 Conductor Ampacity, Insulation Types & Terminal Temperature Ratings 3.2 Ambient Temperature Correction & Raceway Conductor Bundling Derating 3.3 Outlet & Junction Box Volume Fill Calculations (NEC 314.16) 3.4 Conduit Fill Calculations & Large Pull Box Sizing (NEC 314.28)
4 Chapter 4: Branch Circuits & Overcurrent Protection
4.1 Branch Circuit Ratings, Multiwire Circuits & Receptacle Placement 4.2 GFCI & AFCI Protection Mandates and Idaho Code Clarifications 4.3 Overcurrent Protective Devices, Standard Ratings & Small Conductor Rules 4.4 Feeder & Transformer Tap Rules (NEC 240.21)
5 Chapter 5: Feeders, Services & Outside Branch Circuits
5.1 Feeder Conductor Sizing, Neutral Calculations & Voltage Drop 5.2 Outside Branch Circuits, Feeders & Overhead/Underground Clearances 5.3 Service Drop, Service Lateral & Service-Entrance Sizing 5.4 Service Disconnecting Means, Emergency Disconnects & Surge Protection
6 Chapter 6: Load Calculations: Dwellings & Commercial
6.1 General Lighting, Small Appliance & Laundry Load Calculations 6.2 Standard Method Single-Family Dwelling Service Calculations (NEC 220 Part III) 6.3 Optional Method Single-Family & Multifamily Calculations (NEC 220 Part IV) 6.4 Commercial & Industrial Feeder/Service Calculations
7 Chapter 7: Grounding and Bonding: Systems & Electrodes
7.1 Grounding vs. Bonding Fundamentals & System Grounding 7.2 Grounding Electrodes & Grounding Electrode Conductor (GEC) Sizing 7.3 Main Bonding Jumpers, System Bonding Jumpers & Supply-Side Bonding
8 Chapter 8: Grounding and Bonding: Equipment & Enclosures
8.1 Equipment Grounding Conductors (EGC) Types, Installation & Sizing (Table 250.122) 8.2 Separately Derived Systems (SDS) Transformers & Generator Grounding 8.3 Service Enclosure Bonding, Concentric Knockouts & Effective Ground-Fault Path
9 Chapter 9: Wiring Methods, Cables & Conduits
9.1 General Requirements for Wiring Methods & Underground Installations (Article 300) 9.2 Nonmetallic-Sheathed (NM), Metal-Clad (MC) & Armored (AC) Cables 9.3 Metallic & Nonmetallic Raceway Systems (EMT, PVC, RMC, FMC) 9.4 Cabinets, Cutout Boxes & Outlet Box Installation Rules (Articles 312 & 314)
10 Chapter 10: Equipment for General Use: Devices, Luminaires & Appliances
10.1 Switches, Receptacles & Device Installation Standards (Articles 404 & 406) 10.2 Luminaire Clearances, Closet Rules & Lighting Track (Article 410) 10.3 Household Appliances & Fixed Electric Space Heating (Articles 422 & 424) 10.4 Generators, Transformer Overcurrent Protection & Panelboards
11 Chapter 11: Motors, Motor Circuits & Controllers
11.1 Motor Nameplate vs. Table FLC & Branch Circuit Conductor Sizing 11.2 Branch Circuit Short-Circuit & Ground-Fault Protection (Table 430.52) 11.3 Motor Overload Protection Sizing & Selection (NEC 430 Part III) 11.4 Motor Disconnects, Controllers & Multimotor Feeder Calculations
12 Chapter 12: Special Occupancies & Hazardous Locations
12.1 Hazardous (Classified) Locations: Classes, Divisions, Zones & Seals 12.2 Commercial Garages, Repair Hangars & Fuel Dispensing Facilities 12.3 Health Care Facilities: Patient Care Spaces & Redundant Grounding (Article 517) 12.4 Agricultural Buildings, Marinas, Boatyards & RV Parks
13 Chapter 13: Special Equipment, Emergency Systems & Renewable Energy
13.1 Swimming Pools, Spas, Hot Tubs & Equipotential Bonding (Article 680) 13.2 Electric Vehicle Supply Equipment (EVSE) Installation & Sizing (Article 625) 13.3 Solar Photovoltaic (PV) Systems & Energy Storage Systems (Articles 690 & 706) 13.4 Emergency, Standby Power Systems & Fire Pumps (Articles 700, 701, 702 & 695) 13.5 Fire Alarm, Optical Fiber & Power-Limited Circuits (Articles 760, 770 & 800)
2.3 DC & AC Voltage Drop Calculations and Conductor Sizing
Key Takeaways Explain This Topic AI
National Electrical Code Informational Notes 210.19(A) and 215.2(A) recommend a maximum voltage drop of 3% on branch circuits or feeders, and a maximum total combined drop of 5% from the service point to the furthest outlet for reasonable operating efficiency.
The standard single-phase/DC voltage drop formula is VD = (2 * K * I * D) / CM, where K is conductor resistivity (12.9 for copper, 21.2 for aluminum at 75°C), I is current in amperes, D is one-way distance in feet, and CM is circular mil area from NEC Chapter 9 Table 8.
The three-phase voltage drop formula replaces the factor of 2 with √3 (1.732): VD_3φ = (1.732 * K * I * D) / CM.
To size conductors for a target allowable voltage drop, rearrange the formula to solve for Circular Mils: CM = (2 * K * I * D) / VD_allowable for single-phase, and CM = (1.732 * K * I * D) / VD_allowable for three-phase.
When phase conductors are upsized from minimum ampacity sizes to compensate for voltage drop, NEC 250.122(B) mandates that equipment grounding conductors (EGC) must be proportionally increased in circular mil area.
Last updated: August 2026
2.3 DC & AC Voltage Drop Calculations and Conductor Sizing
All electrical conductors possess inherent resistance. When current flows through a wire, this resistance produces an inevitable drop in voltage across the length of the circuit according to Ohm's Law (V_drop = I x R_wire). As circuit runs extend over long distances—such as parking lot lighting, detached agricultural outbuildings, deep well irrigation pumps, or remote subpanels—excessive voltage drop impairs equipment performance, wastes energy, and damages sensitive loads.
1. Why Voltage Drop Matters & NEC Recommendations +-----------------------------------------------------------------------------+
- | CONSEQUENCES OF EXCESSIVE VOLTAGE DROP |
- | |
- | EQUIPMENT TYPE SYMPTOMS / IMPACT OF LOW VOLTAGE |
- | ----------------------------------------------------------------------- |
- | Electric Motors Higher operating current (I = P/E), severe winding |
- | overheating, reduced starting torque (Torque ∝ V²), |
- | nuisance thermal overload tripping. |
- | |
- | Lighting Systems Dramatic reduction in lumen output (Incandescent lumen |
- | output drops by ~3.4% per 1% voltage drop; LED drivers |
- | flicker or drop out). |
- | |
- | Electronics & PLCs Undervoltage lockouts, erratic relay chattering, |
- | microprocessor resets, communications bus failure. |
- | |
- | Heaters / Elements Heat output drops with the square of voltage (P = E²/R)|
- +-----------------------------------------------------------------------------+
- The NEC 3% / 5% Guidance Rule
While the National Electrical Code does not generally enforce voltage drop as a mandatory rule for standard branch circuits (with specific safety exceptions such as Article 695 for Fire Pumps), the Code provides strict design recommendations in Informational Notes :
NEC 210.19(A) Informational Note No. 4 (Branch Circuits): Conductors sized to prevent a voltage drop exceeding 3% at the farthest outlet of power, heating, or lighting.
NEC 215.2(A)(1) Informational Note No. 2 (Feeders): Conductors sized to prevent a voltage drop exceeding 3% on feeder runs.
Overall System Limit: The maximum total combined voltage drop on both the feeder and branch circuit combined should not exceed 5% from the service point to the final utilization equipment. +-----------------------------------------------------------------------------+
- | NEC VOLTAGE DROP ARCHITECTURE |
- | |
- | [SERVICE POINT] |
- | | |
- | +==== Feeder Run (Max 3% Drop) ====> [SUBPANEL] |
- | | |
- | +==== Branch Circuit ==|
- | (Max 3% Drop) |
- | | |
- | v |
- | [TOTAL COMBINED DROP FROM SERVICE TO FARTHEST OUTLET: MAX 5%] [LOAD] |
- +-----------------------------------------------------------------------------+
Note
Mandatory NEC Voltage Drop Exceptions: Voltage drop calculations are mandatory for Fire Pumps (NEC 695.7) —requiring no more than a 15% drop during motor starting and no more than 5% under full-load running conditions—and Sensitive Electronic Equipment (NEC 647.4(D)) (1.5% branch, 2.5% total).
2. The Standard Voltage Drop Formulas
Voltage drop calculations require five primary variables: +-----------------------------------------------------------------------------+
- | VOLTAGE DROP FORMULA VARIABLES |
- | |
- | VARIABLE DEFINITION |
- | ----------------------------------------------------------------------- |
- | VD Voltage Drop (in Volts) |
- | K Conductor Resistivity Constant (Ohms-cmil / foot at 75°C): |
- | • Copper (Cu) = 12.9 Ω·cmil/ft |
- | • Aluminum (Al) = 21.2 Ω·cmil/ft |
- | I Circuit Design Load Current (in Amperes) |
- | D One-Way Distance from power source to load (in Feet) |
- | CM Conductor Cross-Sectional Area (in Circular Mils) |
- +-----------------------------------------------------------------------------+
- Single-Phase & DC Circuits (Round-Trip Factor = 2)
Because single-phase and DC circuits use one conductor to deliver current and a second conductor to return current, the formula multiplies one-way length by 2:
- VD_1-Phase / DC = (2 x K x I x D) / (CM)
- Three-Phase Balanced Circuits (Line Factor = 1.732 ≈ 1.732)
In a balanced three-phase circuit, the vector sum of line currents replaces the return conductor with the geometric factor 1.732:
- VD_3-Phase = (1.732 x K x I x D) / (CM)
- Formula Rearranged to Size Conductors (Solving for Circular Mils CM)
To determine the minimum conductor size required to stay within an allowable voltage drop limit (VD_allowable):
- CM_1-Phase = (2 x K x I x D) / (VD_allowable) | CM_3-Phase = (1.732 x K x I x D) / (VD_allowable)
- % Voltage Drop = (VD / V_system) x 100
- 3. Conductor Properties Reference (NEC Chapter 9, Table 8)
To convert calculated Circular Mil values to standard American Wire Gauge (AWG) or kcmil sizes, electricians reference NEC Chapter 9, Table 8 :
Conductor Size (AWG/kcmil) Area in Circular Mils (CM) Copper Resistance (Ω / 1,000 ft) Aluminum Resistance (Ω / 1,000 ft)
- 14 AWG 4,110 3.07 5.06
- 12 AWG 6,530 1.93 3.18
- 10 AWG 10,380 1.21 2.00
- 8 AWG 16,510 0.764 1.26
- 6 AWG 26,240 0.491 0.808
- 4 AWG 41,740 0.308 0.508
- 3 AWG 52,620 0.245 0.403
- 2 AWG 66,360 0.194 0.319
- 1 AWG 83,690 0.154 0.253
- 1/0 AWG 105,600 0.122 0.201
- 2/0 AWG 133,100 0.0967 0.159
- 3/0 AWG 167,800 0.0766 0.126
- 4/0 AWG 211,600 0.0608 0.100
- 250 kcmil 250,000 0.0515 0.0847
- 350 kcmil 350,000 0.0367 0.0605
- 500 kcmil 500,000 0.0258 0.0424
- 4. Step-by-Step Worked Calculation Examples
- Example 3.1: Sizing Parking Lot Lighting (Single-Phase 120V)
A 120 V single-phase branch circuit powers commercial LED pole lights drawing a continuous load of 16 A. The one-way run from the panel to the furthest luminaire is 175 feet. Using copper conductors (K = 12.9), size the conductors to limit voltage drop to a maximum of 3%.
Step 1: Calculate Allowable Voltage Drop (VD_allowable): VD_allowable = 120 V x 0.03 = 3.60 Volts
Step 2: Apply the Circular Mil Sizing Formula: CM = (2 x K x I x D) / (VD_allowable) = (2 x 12.9 x 16 A x 175 ft) / (3.60 V) = 72,240 / 3.60 = 20,066.67 CM
Step 3: Select Conductor Size from NEC Table 8:
- 10 AWG = 10,380 CM (Too small)
- 8 AWG = 16,510 CM (Too small: 16,510 < 20,067)
- 6 AWG = 26,240 CM (Compliant!)
Step 4: Verify Actual Voltage Drop with 6 AWG: VD_actual = (2 x 12.9 x 16 x 175) / (26,240) = 72,240 / 26,240 = 2.75 V (2.29% <= 3.0%)
Example 3.2: Deep Well Submersible Pump (Single-Phase 240V)
A 240 V single-phase residential irrigation well pump draws 28 A full load. The one-way distance from the service disconnect to the well head is 320 feet. Using copper conductors (K = 12.9), determine the minimum AWG size for a maximum 3% drop.
Step 1: Calculate Allowable Voltage Drop: VD_allowable = 240 V x 0.03 = 7.20 Volts
Step 2: Solve for Minimum Circular Mils: CM = (2 x 12.9 x 28 A x 320 ft) / (7.20 V) = 231,168 / 7.20 = 32,106.67 CM
Step 3: Lookup in Table 8:
- 6 AWG = 26,240 CM (Too small)
- 4 AWG = 41,740 CM (Compliant!)
- Example 3.3: 3-Phase Commercial Feeder to Detached Building
A 480V 3-phase feeder supplies an outbuilding drawing 70 A balanced continuous load over a one-way distance of 450 feet. Using aluminum conductors (K = 21.2), size the feeder conductors for a maximum 3% voltage drop.
Step 1: Calculate Allowable Voltage Drop: VD_allowable = 480 V x 0.03 = 14.40 Volts
Step 2: Solve for Circular Mils using the 3-Phase Formula: CM = (1.732 x K x I x D) / (VD_allowable) = (1.732 x 21.2 x 70 A x 450 ft) / (14.40 V) = 1,156,669.2 / 14.40 = 80,324.25 CM
Step 3: Select Conductor Size from NEC Table 8:
- 2 AWG Aluminum = 66,360 CM (Too small)
- 1 AWG Aluminum = 83,690 CM (Compliant!)
- 5. Upsizing Equipment Grounding Conductors (NEC 250.122(B))
A critical exam rule often tested in conjunction with voltage drop is NEC 250.122(B) :
Warning
NEC 250.122(B) Proportional Grounding Rule: Where ungrounded (phase) conductors are increased in size from the minimum required ampacity (e.g., upsized for voltage drop), the equipment grounding conductors (EGC) must be proportionally increased in size according to the circular mil area of the ungrounded conductors.
Multiplier = (CM_actual upsized phase conductor) / (CM_minimum code phase conductor) CM_new EGC = CM_standard Table 250.122 EGC x Multiplier
Worked Example: Sizing the Proportional EGC
A 50A circuit protected by a 50A breaker normally requires 8 AWG copper phase conductors (16,510 CM) and a 10 AWG copper EGC (10,380 CM, per NEC Table 250.122). Due to a 400 ft distance, the phase conductors are upsized to 4 AWG copper (41,740 CM). What size EGC is required?
- Calculate Area Increase Ratio: Ratio = (41,740 CM (4 AWG)) / (16,510 CM (8 AWG)) = 2.528
- Calculate Required EGC Area: CM_EGC = 10,380 CM (10 AWG) x 2.528 = 26,242 CM
Select from Table 8:
8 AWG = 16,510 CM (Too small)
6 AWG = 26,240 CM ≈ 26,242 CM (Required EGC size is 6 AWG Copper) .