Study guide

1.2 Idaho Electrical Licensing Laws (Title 54, Ch. 10) & IDAPA 24.39.10 Requirements

Idaho Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation, NEC Navigation & Idaho Regulations

1.1 Idaho Journeyman Exam Format, PSI Logistics & Rapid NEC Navigation 1.2 Idaho Electrical Licensing Laws (Title 54, Ch. 10) & IDAPA 24.39.10 Requirements 1.3 Idaho Permits, Inspection Procedures & State-Specific NEC Amendments 1.4 NEC Article 90 Scope, Code Arrangement & Article 110 General Requirements

2 Chapter 2: Electrical Theory & Essential Math Calculations

2.1 Ohm's Law, Joule's Law & DC Circuit Calculations 2.2 Single-Phase & Three-Phase AC Fundamentals and Power Factor 2.3 DC & AC Voltage Drop Calculations and Conductor Sizing 2.4 NEC Article 100 Essential Definitions for Journeymen

3 Chapter 3: Conductors, Raceways & Box Sizing Calculations

3.1 Conductor Ampacity, Insulation Types & Terminal Temperature Ratings 3.2 Ambient Temperature Correction & Raceway Conductor Bundling Derating 3.3 Outlet & Junction Box Volume Fill Calculations (NEC 314.16) 3.4 Conduit Fill Calculations & Large Pull Box Sizing (NEC 314.28)

4 Chapter 4: Branch Circuits & Overcurrent Protection

4.1 Branch Circuit Ratings, Multiwire Circuits & Receptacle Placement 4.2 GFCI & AFCI Protection Mandates and Idaho Code Clarifications 4.3 Overcurrent Protective Devices, Standard Ratings & Small Conductor Rules 4.4 Feeder & Transformer Tap Rules (NEC 240.21)

5 Chapter 5: Feeders, Services & Outside Branch Circuits

5.1 Feeder Conductor Sizing, Neutral Calculations & Voltage Drop 5.2 Outside Branch Circuits, Feeders & Overhead/Underground Clearances 5.3 Service Drop, Service Lateral & Service-Entrance Sizing 5.4 Service Disconnecting Means, Emergency Disconnects & Surge Protection

6 Chapter 6: Load Calculations: Dwellings & Commercial

6.1 General Lighting, Small Appliance & Laundry Load Calculations 6.2 Standard Method Single-Family Dwelling Service Calculations (NEC 220 Part III) 6.3 Optional Method Single-Family & Multifamily Calculations (NEC 220 Part IV) 6.4 Commercial & Industrial Feeder/Service Calculations

7 Chapter 7: Grounding and Bonding: Systems & Electrodes

7.1 Grounding vs. Bonding Fundamentals & System Grounding 7.2 Grounding Electrodes & Grounding Electrode Conductor (GEC) Sizing 7.3 Main Bonding Jumpers, System Bonding Jumpers & Supply-Side Bonding

8 Chapter 8: Grounding and Bonding: Equipment & Enclosures

8.1 Equipment Grounding Conductors (EGC) Types, Installation & Sizing (Table 250.122) 8.2 Separately Derived Systems (SDS) Transformers & Generator Grounding 8.3 Service Enclosure Bonding, Concentric Knockouts & Effective Ground-Fault Path

9 Chapter 9: Wiring Methods, Cables & Conduits

9.1 General Requirements for Wiring Methods & Underground Installations (Article 300) 9.2 Nonmetallic-Sheathed (NM), Metal-Clad (MC) & Armored (AC) Cables 9.3 Metallic & Nonmetallic Raceway Systems (EMT, PVC, RMC, FMC) 9.4 Cabinets, Cutout Boxes & Outlet Box Installation Rules (Articles 312 & 314)

10 Chapter 10: Equipment for General Use: Devices, Luminaires & Appliances

10.1 Switches, Receptacles & Device Installation Standards (Articles 404 & 406) 10.2 Luminaire Clearances, Closet Rules & Lighting Track (Article 410) 10.3 Household Appliances & Fixed Electric Space Heating (Articles 422 & 424) 10.4 Generators, Transformer Overcurrent Protection & Panelboards

11 Chapter 11: Motors, Motor Circuits & Controllers

11.1 Motor Nameplate vs. Table FLC & Branch Circuit Conductor Sizing 11.2 Branch Circuit Short-Circuit & Ground-Fault Protection (Table 430.52) 11.3 Motor Overload Protection Sizing & Selection (NEC 430 Part III) 11.4 Motor Disconnects, Controllers & Multimotor Feeder Calculations

12 Chapter 12: Special Occupancies & Hazardous Locations

12.1 Hazardous (Classified) Locations: Classes, Divisions, Zones & Seals 12.2 Commercial Garages, Repair Hangars & Fuel Dispensing Facilities 12.3 Health Care Facilities: Patient Care Spaces & Redundant Grounding (Article 517) 12.4 Agricultural Buildings, Marinas, Boatyards & RV Parks

13 Chapter 13: Special Equipment, Emergency Systems & Renewable Energy

13.1 Swimming Pools, Spas, Hot Tubs & Equipotential Bonding (Article 680) 13.2 Electric Vehicle Supply Equipment (EVSE) Installation & Sizing (Article 625) 13.3 Solar Photovoltaic (PV) Systems & Energy Storage Systems (Articles 690 & 706) 13.4 Emergency, Standby Power Systems & Fire Pumps (Articles 700, 701, 702 & 695) 13.5 Fire Alarm, Optical Fiber & Power-Limited Circuits (Articles 760, 770 & 800)

1.2 Idaho Electrical Licensing Laws (Title 54, Ch. 10) & IDAPA 24.39.10 Requirements

Key Takeaways Explain This Topic AI

Under IDAPA 24.39.10.100.02, journeyman candidates qualify either with 8,000 hours of registered apprentice work plus satisfactory completion of a four-year sequence of instruction approved by the Idaho Division of Career-Technical Education, or with 16,000 hours of electrical experience.

Only three categories of work are excluded by rule from journeyman experience: appliance repair, motor winding, and communications.

No more than 2,000 hours of work performed as a limited electrical installer or limited electrical installer trainee may count toward journeyman experience.

Idaho Code 54-1010(3) sets the supervision ratio at one residential, journeyman, or master electrician to no more than six apprentices in a residential setting, and one journeyman or master electrician to no more than two apprentices in any other setting.

Effective 2025, continuing education is no longer required to renew an Idaho Electrical Journeyman or Master license; the journeyman license runs three years with a $45 renewal fee and a $55 reinstatement fee.

Last updated: August 2026

1.2 Idaho Electrical Licensing Laws (Title 54, Ch. 10) & IDAPA 24.39.10 Requirements

Electrical contracting and journeyman work in Idaho is strictly governed by state statute and administrative rule to protect the public health, safety, and property of Idaho residents. The primary legal framework resides in Idaho Code Title 54, Chapter 10 ("Electrical Contractors and Journeymen") and the administrative rules promulgated thereunder in IDAPA 24.39.10 ("Rules of the Idaho Electrical Board") .

The regulatory agency overseeing licensure, examination approvals, disciplinary enforcement, and continuing education compliance is the Idaho Division of Occupational and Professional Licenses (DOPL) acting in concert with the Idaho Electrical Board .

1. Statutory Authority & Governance: DOPL and the Electrical Board

The Idaho Electrical Board is composed of members appointed by the Governor, representing diverse industry sectors including journeyman electricians, electrical contractors, utility suppliers, and the public. Under Idaho Code § 54-1005, the Board possesses authority to:

Establish minimum standards for electrical installations based upon the National Electrical Code.

Establish licensing rules, apprentice registration requirements, and examination criteria.

Review applications, administer examinations via testing contractors, and issue licenses.

Conduct administrative hearings, assess civil penalties, and suspend or revoke licenses for code or statutory violations. +-----------------------------------------------------------------------------+

  • | IDAHO ELECTRICAL REGULATORY JURISDICTION |
  • | |
  • | [IDAHO LEGISLATURE] ---> Idaho Code Title 54, Chapter 10 (Statutes) |
  • | | |
  • | v |
  • | [DOPL / ELECTRICAL BOARD] ---> IDAPA 24.39.10 (Administrative Rules) |
  • | | |
  • | v |
  • | [ENFORCEMENT & LICENSING] ---> State Electrical Inspectors & Exam Staff |
  • +-----------------------------------------------------------------------------+
  • 2. Journeyman Qualification Pathways (IDAPA 24.39.10.200)

An applicant seeking approval to take the Idaho Journeyman Electrician examination must demonstrate documented compliance through one of two primary pathways established by administrative rule. +-----------------------------------------------------------------------------+

  • | IDAHO JOURNEYMAN LICENSING ELIGIBILITY PATHWAYS |
  • | |
  • | [PATHWAY A: FORMAL APPRENTICESHIP PROGRAM] |
  • | * On-the-Job Experience: Minimum 8,000 Hours (4 Years) of registered |
  • | apprenticeship electrical work under direct supervision. |
  • | * Related Instruction: Minimum 4 Years (576 Classroom Hours Total; |
  • | 144 hours/year minimum) of approved electrical vocational schooling. |
  • | |
  • | [PATHWAY B: VERIFIED EXPERIENCE ONLY (NON-APPRENTICE / OUT-OF-STATE)] |
  • | * Practical Experience: Minimum 16,000 Hours (8 Years) of verified |
  • | practical electrical work experience complying with Idaho standards. |
  • | * No formal classroom instruction requirement mandated if 16,000 hours |
  • | are formally documented and verified via employer affidavits. |
  • +-----------------------------------------------------------------------------+
  • Comparison of Qualification Pathways

Pathway Dimension Pathway A: Apprenticeship + Education Pathway B: Experience-Only Pathway

On-the-Job Work Hours 8,000 hours (minimum 4 years of registered on-the-job training) 16,000 hours (minimum 8 years of practical on-the-job electrical experience)

Classroom Instruction 576 hours (4 distinct years of approved curriculum; min 144 hrs/year) None required (experience substitutes for classroom schooling)

Documentation Method DOPL Apprentice Registration history, employer verification affidavits, official school transcripts Employer verification affidavits detailing scope, hours, and supervisory journeyman license numbers

Typical Candidate Graduates of Idaho 4-year apprenticeship programs (e.g., IEC, IBEW/NECA, CSI, CWI, CEI, NIC) Seasoned out-of-state electricians from non-licensing jurisdictions or non-traditional backgrounds

3. Countable vs. Excluded Experience Hours & Installer Credit Caps

Not all electrical or mechanical work can be credited toward the 8,000-hour journeyman requirement. IDAPA 24.39.10 strictly delineates allowable categories of electrical construction experience from excluded tasks. +-----------------------------------------------------------------------------+

  • | EXPERIENCE HOUR AUDIT GUIDELINES |
  • | |
  • | [COUNTABLE HOURS - 100% CREDIT] |
  • | * Installation of electrical raceways, cables, and enclosures |
  • | * Branch circuit and feeder wiring in residential, commercial, industrial |
  • | * Service equipment installation, grounding electrode systems, panels |
  • | * Switchboards, motor control centers, transformers, and industrial power |
  • | |
  • | [LIMITED INSTALLER CREDIT - CAPPED AT 2,000 HOURS MAXIMUM] |
  • | * Specialty electrical work performed under an Idaho Limited Electrical |
  • | Installer license (e.g., HVAC wiring, well pumps, sign illumination) |
  • | |
  • | [EXCLUDED BY RULE - 0% CREDIT (IDAPA 24.39.10.100.02.c)] |
  • | * Appliance repair |
  • | * Motor winding |
  • | * Communications |
  • | |
  • | [ALSO REQUIRED: ACTIVE APPRENTICE REGISTRATION] |
  • | * Hours worked while your apprentice registration was lapsed do NOT |
  • | count toward the required on-the-job time, per DOPL guidance. |
  • +-----------------------------------------------------------------------------+

Warning

Do not over-read the exclusion list. The rule names exactly three excluded categories — appliance repair, motor winding, or communications — and the DOPL Electrical Journeyman application repeats that same three-item list verbatim on the work-verification page. Other categories that candidates often assume are excluded (for example utility line work or factory machine wiring) are not named in the rule; they are governed instead by whether the work was performed as a registered apprentice making electrical installations under a licensed contractor. When in doubt, ask DOPL before you bank four years of hours on an assumption.

Warning

The 2,000-Hour Specialty Cap: An individual who holds an Idaho Limited Electrical Installer license (such as an HVAC technician or water-well pump installer) who subsequently transitions to a general electrical apprenticeship can credit a maximum of 2,000 hours of that specialty experience toward the 8,000-hour journeyman requirement. The remaining 6,000 hours must be general electrical wiring performed as a registered apprentice under journeyman supervision.

4. Apprentice Registration, Renewal & On-Site Supervision Ratios

To lawfully perform electrical work in Idaho prior to acquiring a journeyman license, an individual must be registered as an electrical apprentice with DOPL.

Apprentice Compliance Mandates

Mandatory Registration: An apprentice must apply for registration before performing any electrical work on a job site.

Annual Renewal: Apprentice registrations must be renewed annually by the registrant's renewal date, accompanied by documentation of active enrollment in an approved 4-year vocational educational program or annual schooling progression.

Job Site Supervision Ratios (Idaho Code § 54-1010(3)): Idaho sets its supervision ratios by statute, not by board rule , and the ratio depends on the setting:

Residential setting: one (1) residential electrician, journeyman electrician, or master electrician to no more than six (6) apprentice electricians.

Any setting other than residential: one (1) journeyman electrician or master electrician to no more than two (2) apprentice electricians.

Limited electrical installer trainees: no supervision ratio applies. Section 54-1010(5) also preempts cities, counties, and other local entities from adopting any code, ordinance, policy, or guidance that differs from or is more extensive than these requirements.

Provisional Journeyman License (IDAPA 24.39.10.100.02.b): A candidate who has completed the 16,000 hours but has not yet passed the examination may be issued a provisional journeyman electrician license . DOPL issues it for a six-month term at a $55 fee; there is no reinstatement path for a provisional license. +-----------------------------------------------------------------------------+

  • | IDAHO SUPERVISION RATIOS (IDAHO CODE 54-1010(3)) |
  • | |
  • | RESIDENTIAL SETTING 1 supervisor : up to 6 apprentices |
  • | (supervisor may be a residential, journeyman, or master electrician) |
  • | |
  • | ALL OTHER SETTINGS 1 supervisor : up to 2 apprentices |
  • | (supervisor must be a journeyman or master electrician) |
  • | |
  • | LIMITED INSTALLER TRAINEES No ratio applies |
  • | |
  • | TRAP: the old 1:2-everywhere answer is out of date. Read the setting |
  • | in the question stem before you pick a number. |
  • +-----------------------------------------------------------------------------+
  • 5. License Terms, Fees, and the Continuing-Education Repeal

Once earned, an Idaho Journeyman Electrician license runs for a three-year term . The renewal picture changed materially in 2025, and stale study material is the most common source of wrong answers here.

Caution

Continuing education is no longer required. Effective 2025, continuing education is not required to renew an Idaho Electrical Journeyman or Master license. The current IDAPA 24.39.10 contains no continuing-education section at all — the chapter runs 000 Legal Authority, 001 Scope, 002 Definitions, 100 Licensure and Registration, 200 Practice Standards, 300 Civil Penalties, 500 Permits and Inspections, and 600 Idaho Electrical Code. Any prep book, course description, or website still telling you "24 hours per cycle including 8 hours of code update" is describing the repealed requirement. (The repeal remains contested: at DOPL's July 17, 2026 negotiated-rulemaking meeting on IDAPA 24.39.10, multiple stakeholders — including IEC of Idaho and IBEW 291 — asked the Board to put continuing education back into the rules. Until the Board actually does so, the answer is "none required.")

Idaho Electrical Board Fee Schedule

  • Credential License Fee Renewal Fee Reinstatement Fee Term
  • Apprentice $15 $15 $15 1 year
  • Provisional Journeyman $55 $45 N/A 6 months
  • Journeyman $55 $45 $55 3 years
  • Master $65 $45 $55 3 years
  • Limited Installer $55 $45 $55 3 years
  • Limited Trainee $30 $25 $30 3 years
  • Contractor $125 $100 $125 1 year
  • Limited Contractor $125 $100 $125 1 year

A $15 application fee applies on top of the license fee, so an initial journeyman license costs $70 in total to DOPL. The exam itself is $75, paid separately to PSI when you schedule.

Renewal Mechanics

Renewal Term: Every three (3) years. Renew online through the DOPL Online Services portal at edopl.idaho.gov.

Continuing Education: None required for journeyman or master renewal as of 2025.

Lapsed Licenses: Idaho publishes a $55 reinstatement fee for a lapsed journeyman license — reinstatement is a fee-and-application process, not an automatic requirement to re-sit the 100-question examination. Reinstatement is not available for a provisional journeyman license , which simply expires at six months.

6. Multi-State Reciprocity Agreements

Idaho maintains bilateral reciprocal licensing agreements with a defined set of states. This framework enables Idaho journeymen to obtain equivalent licenses in partner states without re-taking the partner state's written examination, and vice-versa. DOPL maintains the authoritative list in its Reciprocal Information document — check it before you apply, because agreements are added and dropped. +-----------------------------------------------------------------------------+

  • | IDAHO JOURNEYMAN RECIPROCITY (12 STATES) |
  • | |
  • | Colorado (CO) * Maine (ME) * Montana (MT) |
  • | Nebraska (NE) * New Hampshire (NH) * New Mexico (NM) |
  • | North Dakota (ND) * Oklahoma (OK) * Oregon (OR) |
  • | South Dakota (SD) * Texas (TX) * Wyoming (WY) |
  • | |
  • | IDAHO MASTER ELECTRICIAN RECIPROCITY |
  • | |
  • | Wyoming (WY) only |
  • +-----------------------------------------------------------------------------+

Warning

Journeyman and master reciprocity are not the same list. Idaho's journeyman agreements cover twelve states, but its master-electrician reciprocity is limited to Wyoming . A licensed master from another reciprocity partner may still reciprocate at the journeyman level only. Utah is a frequent distractor here: Utah licenses Idaho electricians by endorsement in the other direction, but that is Utah's policy, not an Idaho journeyman reciprocity agreement.

Mandatory Reciprocity Qualifications

To obtain an Idaho Journeyman license via reciprocity, an out-of-state applicant must satisfy all of the following conditions:

Examination Prerequisite: The candidate must have earned their active journeyman license in the reciprocal state by passing a state-administered written examination . Grandfathered licenses or licenses obtained through a third-state reciprocity chain are ineligible.

Active Standing: The out-of-state license must be active, current, and in good standing with no pending disciplinary actions or unresolved suspensions.

Experience Duration: The applicant must have held the reciprocal license in good standing for at least one (1) full year prior to submitting the reciprocity application.

Equivalent Standards: The reciprocal state's qualifying prerequisites must be substantially equivalent to Idaho's 8,000-hour experience standard.