Study guide

1.3 Idaho Permits, Inspection Procedures & State-Specific NEC Amendments

Idaho Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Orientation, NEC Navigation & Idaho Regulations

1.1 Idaho Journeyman Exam Format, PSI Logistics & Rapid NEC Navigation 1.2 Idaho Electrical Licensing Laws (Title 54, Ch. 10) & IDAPA 24.39.10 Requirements 1.3 Idaho Permits, Inspection Procedures & State-Specific NEC Amendments 1.4 NEC Article 90 Scope, Code Arrangement & Article 110 General Requirements

2 Chapter 2: Electrical Theory & Essential Math Calculations

2.1 Ohm's Law, Joule's Law & DC Circuit Calculations 2.2 Single-Phase & Three-Phase AC Fundamentals and Power Factor 2.3 DC & AC Voltage Drop Calculations and Conductor Sizing 2.4 NEC Article 100 Essential Definitions for Journeymen

3 Chapter 3: Conductors, Raceways & Box Sizing Calculations

3.1 Conductor Ampacity, Insulation Types & Terminal Temperature Ratings 3.2 Ambient Temperature Correction & Raceway Conductor Bundling Derating 3.3 Outlet & Junction Box Volume Fill Calculations (NEC 314.16) 3.4 Conduit Fill Calculations & Large Pull Box Sizing (NEC 314.28)

4 Chapter 4: Branch Circuits & Overcurrent Protection

4.1 Branch Circuit Ratings, Multiwire Circuits & Receptacle Placement 4.2 GFCI & AFCI Protection Mandates and Idaho Code Clarifications 4.3 Overcurrent Protective Devices, Standard Ratings & Small Conductor Rules 4.4 Feeder & Transformer Tap Rules (NEC 240.21)

5 Chapter 5: Feeders, Services & Outside Branch Circuits

5.1 Feeder Conductor Sizing, Neutral Calculations & Voltage Drop 5.2 Outside Branch Circuits, Feeders & Overhead/Underground Clearances 5.3 Service Drop, Service Lateral & Service-Entrance Sizing 5.4 Service Disconnecting Means, Emergency Disconnects & Surge Protection

6 Chapter 6: Load Calculations: Dwellings & Commercial

6.1 General Lighting, Small Appliance & Laundry Load Calculations 6.2 Standard Method Single-Family Dwelling Service Calculations (NEC 220 Part III) 6.3 Optional Method Single-Family & Multifamily Calculations (NEC 220 Part IV) 6.4 Commercial & Industrial Feeder/Service Calculations

7 Chapter 7: Grounding and Bonding: Systems & Electrodes

7.1 Grounding vs. Bonding Fundamentals & System Grounding 7.2 Grounding Electrodes & Grounding Electrode Conductor (GEC) Sizing 7.3 Main Bonding Jumpers, System Bonding Jumpers & Supply-Side Bonding

8 Chapter 8: Grounding and Bonding: Equipment & Enclosures

8.1 Equipment Grounding Conductors (EGC) Types, Installation & Sizing (Table 250.122) 8.2 Separately Derived Systems (SDS) Transformers & Generator Grounding 8.3 Service Enclosure Bonding, Concentric Knockouts & Effective Ground-Fault Path

9 Chapter 9: Wiring Methods, Cables & Conduits

9.1 General Requirements for Wiring Methods & Underground Installations (Article 300) 9.2 Nonmetallic-Sheathed (NM), Metal-Clad (MC) & Armored (AC) Cables 9.3 Metallic & Nonmetallic Raceway Systems (EMT, PVC, RMC, FMC) 9.4 Cabinets, Cutout Boxes & Outlet Box Installation Rules (Articles 312 & 314)

10 Chapter 10: Equipment for General Use: Devices, Luminaires & Appliances

10.1 Switches, Receptacles & Device Installation Standards (Articles 404 & 406) 10.2 Luminaire Clearances, Closet Rules & Lighting Track (Article 410) 10.3 Household Appliances & Fixed Electric Space Heating (Articles 422 & 424) 10.4 Generators, Transformer Overcurrent Protection & Panelboards

11 Chapter 11: Motors, Motor Circuits & Controllers

11.1 Motor Nameplate vs. Table FLC & Branch Circuit Conductor Sizing 11.2 Branch Circuit Short-Circuit & Ground-Fault Protection (Table 430.52) 11.3 Motor Overload Protection Sizing & Selection (NEC 430 Part III) 11.4 Motor Disconnects, Controllers & Multimotor Feeder Calculations

12 Chapter 12: Special Occupancies & Hazardous Locations

12.1 Hazardous (Classified) Locations: Classes, Divisions, Zones & Seals 12.2 Commercial Garages, Repair Hangars & Fuel Dispensing Facilities 12.3 Health Care Facilities: Patient Care Spaces & Redundant Grounding (Article 517) 12.4 Agricultural Buildings, Marinas, Boatyards & RV Parks

13 Chapter 13: Special Equipment, Emergency Systems & Renewable Energy

13.1 Swimming Pools, Spas, Hot Tubs & Equipotential Bonding (Article 680) 13.2 Electric Vehicle Supply Equipment (EVSE) Installation & Sizing (Article 625) 13.3 Solar Photovoltaic (PV) Systems & Energy Storage Systems (Articles 690 & 706) 13.4 Emergency, Standby Power Systems & Fire Pumps (Articles 700, 701, 702 & 695) 13.5 Fire Alarm, Optical Fiber & Power-Limited Circuits (Articles 760, 770 & 800)

1.3 Idaho Permits, Inspection Procedures & State-Specific NEC Amendments

Key Takeaways Explain This Topic AI

All Idaho electrical permits must be purchased before work commences, the full permit fee must be paid before final inspection, and no wiring may be concealed until the work has been inspected and approved for cover.

Idaho permits expire 365 days after purchase and may be renewed for one additional year for a $65 fee; transfers cost $45 and reinspections cost $65.

IDAPA 24.39.10.300 subjects listed violations to a civil penalty not to exceed $1,000 for each separate count or offense; Idaho Code 54-1017 separately makes violations of the act a misdemeanor.

Idaho deletes many 2023 NEC GFCI locations outright, including 210.8(A)(7) food-preparation areas, 210.8(A)(11) laundry areas, 210.8(F)(1) at-or-below-grade garages, and the dwelling-unit appliance items in 210.8(D).

In one- and two-family dwellings Idaho limits AFCI protection under 210.12(B) to branch circuits and outlets supplying bedrooms, and makes dwelling-unit surge protection and emergency disconnects permissive rather than mandatory.

Last updated: August 2026

1.3 Idaho Permits, Inspection Procedures & State-Specific NEC Amendments

Safe electrical installations depend upon structured regulatory oversight before, during, and after construction. In Idaho, the installation of electrical conductors and equipment is governed by the state permitting and inspection apparatus managed by the Division of Occupational and Professional Licenses (DOPL) .

Additionally, while Idaho adopts the National Electrical Code (NFPA 70) as its baseline engineering benchmark, the Idaho Electrical Board promulgates specific statutory amendments codified under IDAPA 24.39.10.600 . Journeyman candidates must understand these state-specific variations to pass the examination and ensure on-the-job compliance.

1. Electrical Permitting Protocols & Eligibility (Idaho Code § 54-1005)

Under Idaho law, an electrical permit must be purchased and issued prior to commencing any electrical work . Beginning work without a valid permit constitutes a direct statutory violation subject to stop-work orders and financial penalties. +-----------------------------------------------------------------------------+

  • | IDAHO ELECTRICAL PERMIT FRAMEWORK |
  • | |
  • | [LICENSED ELECTRICAL CONTRACTOR PERMITS] |
  • | * Required for all commercial, industrial, and multi-family construction. |
  • | * Required for any residential work performed for compensation. |
  • | * Pulling contractor must employ a licensed supervising Master/Journeyman.|
  • | |
  • | [HOMEOWNER / OWNER-OCCUPANT PERMITS] |
  • | * Strictly limited to single-family dwellings owned AND occupied by |
  • | the individual performing the installation. |
  • | * Prohibited on rental properties, commercial buildings, flips, or ADUs. |
  • | * Homeowner must physically perform the work personally without hiring |
  • | unlicensed third parties. |
  • +-----------------------------------------------------------------------------+
  • Contractor vs. Homeowner Permits Comparison

Permitting Element Electrical Contractor Permit Homeowner (Owner-Occupant) Permit

Eligible Scope All residential, commercial, industrial, agricultural, and institutional installations Single-family owner-occupied residence and associated non-commercial outbuildings only

License Required Valid Idaho Electrical Contractor License & registered Supervising Electrician None required (owner must sign an affidavit certifying personal residency and labor)

Rental / Commercial Work Fully authorized within license classification Strictly Prohibited (cannot pull permit for rental homes, apartments, or businesses)

Worker Qualifications Licensed Journeymen and registered Apprentices adhering to 1:2 ratios Homeowner personally; family members or unlicensed helpers cannot receive compensation

2. Mandatory Inspection Workflow & Phasing Protocols

Electrical projects require step-by-step inspections conducted by state or municipal electrical inspectors. Work must remain exposed and accessible until signed off. +-----------------------------------------------------------------------------+

  • | CHRONOLOGICAL INSPECTION WORKFLOW PHASES |
  • | |
  • | [PHASE 1: SERVICE & UNDERGROUND INSPECTION] |
  • | * Trench depth verified per Table 300.5 (e.g., 24" direct burial, 18" PVC)|
  • | * Conduit sizing, grounding electrodes (ground rods, Ufer/CEE) exposed |
  • | * Meter base, disconnect enclosures, and service mast structural support |
  • | | |
  • | v |
  • | [PHASE 2: ROUGH-IN INSPECTION] |
  • | * Performed BEFORE insulation, drywall, or vapor barriers are installed |
  • | * All conduits, cables (NM-B, MC), and outlet boxes secured in framing |
  • | * Conductors stripped, box makeup complete with ground wires spliced |
  • | * Nail plates installed on studs where cables pass within 1-1/4" of edge |
  • | | |
  • | v |
  • | [PHASE 3: FINAL ELECTRICAL INSPECTION] |
  • | * All switches, receptacles, luminaires, and appliances fully installed |
  • | * Faceplates and covers secured; deadfronts in panelboards closed |
  • | * Circuit directory typed or legibly marked per NEC 408.4 |
  • | * GFCI/AFCI devices tested; system fully energized and ready for occupancy|
  • +-----------------------------------------------------------------------------+

Caution

Concealment Before Inspection is a Violation: IDAPA 24.39.10.500.01.a.i states that no wiring or equipment may be concealed in any manner from access or sight until the work has been inspected and approved for cover by the electrical inspector, except for installations under Idaho Code § 54-1005(3). Drywall, insulation, or backfill installed before that approval is subject to removal at the contractor's expense.

Permit Lifecycle & Published Fees (IDAPA 24.39.10.500)

  • Permit Event Rule Amount / Deadline
  • Purchase timing 500.01.a All permits must be purchased before work is commenced
  • Fee payment 500.01.a Total permit fee must be paid prior to final inspection
  • Expiration 500.01.c Permits expire 365 days from the purchase date
  • Renewal 500.01.c $65 for one additional year, with Division approval
  • Transfer 500.01.d $45 administrative fee; requires notarized written authorization from the original holder
  • Requested inspection 500.03 $65 per inspection

Reinspection 500.04 $65 per reinspection (work not ready, bad directions, or no response to a correction notice)

  • Virtual inspection 500.05 $45 for contractors and specialty contractors on qualifying installations
  • Plan check 500.06 $65 minimum for one hour or less; $65 per additional hour or portion

New one-family dwelling permits are priced by living area: $130 up to 1,500 sq ft, $195 for 1,501-2,500, $260 for 2,501-3,500, $325 for 3,501-4,500, and $325 plus $65 per additional 1,000 sq ft above 4,500. Two-family dwellings are $260 ; multifamily is $130 per building plus $65 per unit . An existing dwelling unit permit is $65 per inspection .

Commercial and industrial permits are priced off total wiring cost: $60 plus 2% up to $10,000; $260 plus 1% of the amount over $10,000 up to $100,000; and $1,160 plus 0.5% of the amount over $100,000. Small work not exceeding $500 in cost and not involving a change in service connections is $10 .

Tip

Energizing before inspection. IDAPA 24.39.10.200.04 allows a power supply company to connect and energize a service to the line side of the service disconnect before a passed inspection, at the request of a licensed electrical contractor and on receipt of a copy of the permit, in two situations only: to preserve life or property , or to provide temporary service for construction . Any contractor who energizes an installation before inspection assumes full responsibility for it.

3. Idaho Inspection Tagging & Enforcement System

Idaho state electrical inspectors utilize a standardized color-coded tagging protocol to communicate inspection outcomes on job sites. +-----------------------------------------------------------------------------+

  • | IDAHO INSPECTION TAGGING MATRIX |
  • | |
  • | [GREEN TAG: APPROVED] |
  • | * Meaning: Installation meets all NEC and Idaho code requirements. |
  • | * Action: Authorizes utility power connection or drywall concealment. |
  • | |
  • | [YELLOW TAG: CONDITIONAL / CORRECTIONS NOTICE] |
  • | * Meaning: Minor code non-conformances identified that require correction.|
  • | * Action: Contractor must remedy specified defects. Work may proceed |
  • | conditionally, but a re-inspection or sign-off is required before final. |
  • | |
  • | [RED TAG: REJECTED / STOP WORK ORDER] |
  • | * Meaning: Severe safety hazard, unpermitted work, or unlicensed labor. |
  • | * Action: Immediate cessation of work; system cannot be energized. |
  • | Subject to re-inspection fees and potential administrative penalties. |
  • +-----------------------------------------------------------------------------+
  • Civil Penalties (IDAPA 24.39.10.300)

The civil-penalty ceiling lives in the rules , not the statute. IDAPA 24.39.10.300 provides that the acts listed in that section subject the violator to a civil penalty not to exceed one thousand dollars ($1,000) for each separate count or offense — note the wording: per count or offense , not per day.

The ten enumerated violation categories are worth memorizing, because exam items often ask which conduct is penalized:

  • # Violation (IDAPA 24.39.10.300)
  • 01 Failure to comply with any provision of Chapter 10, Title 54, Idaho Code or Board Rule
  • 02 Performing electrical work without an active license or registration (except as allowed by § 54-1016)
  • 03 Performance outside the scope of a limited electrical license or registration
  • 04 Knowing employment of a person without an active license or registration

05 Working as an apprentice or installer trainee without required supervision, or employing one without providing it

  • 06 Failure to obtain a required permit, pay applicable fees, properly post a permit, or request an inspection
  • 07 Failure to make corrections in the time allotted in the notice
  • 08 Misrepresentation of permit or inspection fees to the customer

09 Advertising as an electrical contractor without a current license, or advertising without the license number

10 Failure to comply with any lawful order of the Board or Division administrator

Idaho Code § 54-1017 is a separate provision: it makes violations of the act — including engaging in the trade without the required license or registration — a misdemeanor . Distinguish the two: § 54-1017 is the criminal provision; IDAPA 24.39.10.300 is the $1,000-per-offense civil provision.

4. State-Specific Idaho Amendments to the 2023 NEC (IDAPA 24.39.10.600)

The Idaho Electrical Board adopts the 2023 National Electrical Code subject to specific state amendments designed to accommodate regional construction practices, economic practicality, and installer safety.

IDAPA 24.39.10.600.01 adopts the National Electrical Code, 2023 Edition and then amends it. The great majority of Idaho's amendments delete or soften 2023 NEC requirements — they rarely add requirements. That direction matters: if a question asks what Idaho requires in a dwelling and the national answer is "GFCI," "AFCI," "SPD," or "emergency disconnect," check the Idaho list first. +-----------------------------------------------------------------------------+

  • | HOW TO THINK ABOUT THE IDAHO AMENDMENTS (IDAPA 24.39.10.600) |
  • | |
  • | [DELETED OUTRIGHT] Idaho strikes the NEC text; the requirement is |
  • | simply gone in Idaho. |
  • | e.g. 210.8(A)(7), 210.8(A)(11), 422.5(A)(7) |
  • | |
  • | [REPLACED] Idaho substitutes different text, usually the |
  • | narrower pre-2020 scope. |
  • | e.g. 210.8(A)(5), 210.8(A)(8), 210.8(B)(7) |
  • | |
  • | [MADE PERMISSIVE] "shall be installed" becomes "shall be permitted" |
  • | for one- and two-family dwellings. |
  • | e.g. 225.41, 230.85, and the SPD sections |
  • | |
  • | [ADDED ALLOWANCE] Idaho adds an option the NEC does not give. |
  • | e.g. 210.52(C) item (4) island receptacles |
  • +-----------------------------------------------------------------------------+
  • A. Ground-Fault Circuit-Interrupter Amendments (NEC 210.8)

This is the single densest cluster of Idaho amendments and the highest-yield block on the exam.

NEC 2023 Provision National Requirement Idaho Amendment (IDAPA 24.39.10.600.01)

210.8(A) opening text GFCI required for 125V through 250V receptacles in the listed dwelling locations Delete the reference to 250-volt receptacles. Idaho's dwelling GFCI scope reverts to 125-volt receptacles

210.8(A)(5) Basements All areas of basements Delete and replace with: Unfinished areas of basements

210.8(A)(7) Food prep areas Areas with sinks and permanent provisions for food preparation, beverage preparation, or cooking Deleted

210.8(A)(8) Sinks Sinks — receptacles within 6 ft of the inside edge of the bowl Delete and replace with: Sinks located in areas other than kitchens where receptacles are within 1.8 m (6 ft) of the inside edge of the sink

210.8(A)(11) Laundry areas Laundry areas Deleted

210.8(B) Non-dwelling list Includes (3) food/beverage prep areas, (4) serving areas, (14) laundry areas Delete list items (3), (4), and (14)

210.8(B)(7) Sinks Sinks in non-dwelling occupancies Delete and replace with: Sinks located in kitchens and any other area where receptacles are within 1.8 m (6 ft) of the inside edge of the sink

210.8(D) Specific appliances Dwelling-unit outlets supplying listed appliances require GFCI In dwelling units only, delete (7) dishwashers, (8) electric ranges, (9) wall-mounted ovens, (10) counter-mounted cooking units, (11) clothes dryers, and (12) microwave ovens

210.8(F) Outdoor outlets GFCI for outdoor dwelling outlets, including (1) at-or-below-grade garages and (2) accessory buildings Delete list items (1) and (2)

422.5(A)(7) Dishwashers Dishwashers require GFCI protection Delete list item (7) dishwashers

Important

The dishwasher appears twice for a reason. Idaho deletes the dishwasher from both 210.8(D) (dwelling units) and 422.5(A). A question that asks whether a household dishwasher requires GFCI protection in Idaho has the answer no under the state amendments, even though the national 2023 NEC says yes.

B. Arc-Fault Circuit-Interrupter Amendment (NEC 210.12(B))

National 2023 NEC Idaho Amendment

210.12(B) requires AFCI protection for 120V, single-phase, 15A and 20A branch circuits supplying outlets or devices in dwelling-unit kitchens, family rooms, dining rooms, living rooms, parlors, libraries, dens, bedrooms, sunrooms, recreation rooms, closets, hallways, laundry areas, and similar rooms or areas 210.12(B) shall apply in full. Exception: In one- and two-family dwelling units, AFCI protection shall only apply to all branch circuits and outlets supplying BEDROOMS. All other locations in such units are exempt.

Caution

This is the highest-yield single amendment in Idaho. In a one- or two-family dwelling, Idaho requires AFCI protection only in bedrooms — essentially the 2002-era NEC scope. Multifamily dwelling units and other occupancies still get the full 210.12(B) list, because the exception is written for one- and two-family dwelling units only.

C. Surge Protection and Emergency Disconnect Amendments

NEC 2023 Provision National Requirement Idaho Amendment

215.18 Surge protection (feeders) Applies in full Applies in full. Exception: for dwelling units, an SPD shall be permitted when installed in compliance with 215.18(B) through (E); delete 215.18(A)(1)

225.41 Emergency disconnects (outside feeders) An emergency disconnecting means shall be installed For one- and two-family dwelling units, an emergency disconnecting means shall be PERMITTED when installed per 225.41(A), (B), and (C)

225.42 Surge protection Applies in full Applies in full. Exception: for dwelling units, an SPD shall be permitted per 225.42(B) through (E); delete 225.42(A)(1)

230.67 Surge protection (services) Dwelling-unit services shall be provided with a Type 1 or Type 2 SPD Applies in full. Exception: for dwelling units, an SPD shall be permitted per 230.67(B) through (E); delete 230.67(A)(1)

230.85 Emergency disconnects For one- and two-family dwelling units, an emergency disconnecting means shall be installed For one- and two-family dwelling units, an emergency disconnecting means shall be PERMITTED when installed per 230.85(A), (B), (D), and (E). Delete 230.85(C) (the replacement provision)

Warning

"Shall be permitted" is not "shall be installed." Idaho converts the dwelling-unit surge-protection and emergency-disconnect mandates into options. If an Idaho exam question asks whether a new one-family dwelling service must have a whole-house SPD or an exterior emergency disconnect, the state answer is no — it is permitted, not required . The technical rules for how to install one (marking, rating, grouping) still apply if you choose to install it.

D. Receptacle Placement Amendments (NEC 210.52)

NEC 2023 Provision Idaho Amendment

210.52(C) Countertops and work surfaces Add list item (4) — Island and Peninsular Countertop Spaces: if installed , receptacle outlets shall also be permitted to be mounted not more than 300 mm (12 in.) below the countertop or work surface . Receptacles mounted below a countertop in accordance with this exception shall not be located where the countertop or work surface extends more than 150 mm (6 in.) beyond its support base

210.52(E)(3) Balconies, decks, porches Delete and replace: balconies, decks, and porches with an overall area of 20 square feet or more that are accessible from inside the dwelling unit shall have at least one receptacle outlet within the perimeter, located not more than 2.0 m (6½ ft) above the balcony, deck, or porch surface

Important

Read the island rule carefully. Idaho does not require an island receptacle by this amendment — it adds a permitted mounting position . The 12-inch-below-countertop option is unavailable where the countertop overhangs its support base by more than 6 inches, because a bather-height overhang would put the receptacle under a shelf where a cord could be trapped.

E. Wiring Method and Equipment Amendments

NEC 2023 Provision Idaho Amendment

110.3(A) and 110.3(B) Shall not apply to submersible well pumps installed in swimming and marine areas (all other equipment in the installation is still covered)

314.27(C) Paddle-fan boxes Delete the second paragraph — Idaho removes the requirement that a ceiling outlet box be listed for sole support of a paddle fan merely because spare, separately switched ungrounded conductors were run to it

334.10(3) Type NM in Types III/IV/V construction Replaced: cables shall be concealed within walls, floors, or ceilings providing a thermal barrier with at least a 15-minute finish rating ; cables in attics and underfloor areas not designed to be occupied are considered concealed

334.15(C) NM in crawl spaces Where crawl space height does not exceed 1.4 m (4½ ft) , NM cables running at angles with joists may be secured to the bottom edge of the joist ; cables within 2.1 m (7 ft) of the crawl space access must comply with 320.23

Pole lighting Roadway lighting poles 40 ft or less supporting no more than four luminaires at 300 V or less to ground are not considered structures. Parking areas are expressly not roadways

675.8(B) Irrigation machines A disconnecting means must always be provided at the point of service from the utility, no matter where the machine's own disconnect is located

682.10 through 682.15 A series of submersible-well-pump amendments covering HDPE chase methods, heat-shrink splice covering, anchoring, "Emergency Pump Stop" controller circuits, and 30 mA GFCI/GFEP for pumps rated 60 A or less

690.12 PV rapid shutdown Exempts detached structures whose sole purpose is housing PV equipment, and buildings with no utility source that meet distance/setback/lockable-disconnect/placard conditions. 690.12(A) further excludes certain array-originated circuits from being "controlled conductors"

706.5 Energy storage listing ESS shall be listed — this shall not apply to lead-acid batteries

706.15(B) Off-grid systems For one- and two-family dwellings, a disconnecting means or its remote control shall be located at a readily accessible location

Note

Currency check. These amendments carry an effective date of 4-4-25 in the Idaho Administrative Code, and the 2023 NEC became Idaho's tested code edition on August 1, 2025 . DOPL opened a negotiated rulemaking on IDAPA 24.39.10 (Docket 24-3910-2601) with a public meeting on July 17, 2026 , exploring additional exceptions and exemptions. Nothing in that docket had been adopted as of this writing, so the amendments above remain the operative Idaho rules — but confirm the current chapter at adminrules.idaho.gov before relying on any of them in the field.