Study guide
1.4 NEC Article 90 Scope, Code Arrangement & Article 110 General Requirements
Idaho Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Orientation, NEC Navigation & Idaho Regulations
1.1 Idaho Journeyman Exam Format, PSI Logistics & Rapid NEC Navigation 1.2 Idaho Electrical Licensing Laws (Title 54, Ch. 10) & IDAPA 24.39.10 Requirements 1.3 Idaho Permits, Inspection Procedures & State-Specific NEC Amendments 1.4 NEC Article 90 Scope, Code Arrangement & Article 110 General Requirements
2 Chapter 2: Electrical Theory & Essential Math Calculations
2.1 Ohm's Law, Joule's Law & DC Circuit Calculations 2.2 Single-Phase & Three-Phase AC Fundamentals and Power Factor 2.3 DC & AC Voltage Drop Calculations and Conductor Sizing 2.4 NEC Article 100 Essential Definitions for Journeymen
3 Chapter 3: Conductors, Raceways & Box Sizing Calculations
3.1 Conductor Ampacity, Insulation Types & Terminal Temperature Ratings 3.2 Ambient Temperature Correction & Raceway Conductor Bundling Derating 3.3 Outlet & Junction Box Volume Fill Calculations (NEC 314.16) 3.4 Conduit Fill Calculations & Large Pull Box Sizing (NEC 314.28)
4 Chapter 4: Branch Circuits & Overcurrent Protection
4.1 Branch Circuit Ratings, Multiwire Circuits & Receptacle Placement 4.2 GFCI & AFCI Protection Mandates and Idaho Code Clarifications 4.3 Overcurrent Protective Devices, Standard Ratings & Small Conductor Rules 4.4 Feeder & Transformer Tap Rules (NEC 240.21)
5 Chapter 5: Feeders, Services & Outside Branch Circuits
5.1 Feeder Conductor Sizing, Neutral Calculations & Voltage Drop 5.2 Outside Branch Circuits, Feeders & Overhead/Underground Clearances 5.3 Service Drop, Service Lateral & Service-Entrance Sizing 5.4 Service Disconnecting Means, Emergency Disconnects & Surge Protection
6 Chapter 6: Load Calculations: Dwellings & Commercial
6.1 General Lighting, Small Appliance & Laundry Load Calculations 6.2 Standard Method Single-Family Dwelling Service Calculations (NEC 220 Part III) 6.3 Optional Method Single-Family & Multifamily Calculations (NEC 220 Part IV) 6.4 Commercial & Industrial Feeder/Service Calculations
7 Chapter 7: Grounding and Bonding: Systems & Electrodes
7.1 Grounding vs. Bonding Fundamentals & System Grounding 7.2 Grounding Electrodes & Grounding Electrode Conductor (GEC) Sizing 7.3 Main Bonding Jumpers, System Bonding Jumpers & Supply-Side Bonding
8 Chapter 8: Grounding and Bonding: Equipment & Enclosures
8.1 Equipment Grounding Conductors (EGC) Types, Installation & Sizing (Table 250.122) 8.2 Separately Derived Systems (SDS) Transformers & Generator Grounding 8.3 Service Enclosure Bonding, Concentric Knockouts & Effective Ground-Fault Path
9 Chapter 9: Wiring Methods, Cables & Conduits
9.1 General Requirements for Wiring Methods & Underground Installations (Article 300) 9.2 Nonmetallic-Sheathed (NM), Metal-Clad (MC) & Armored (AC) Cables 9.3 Metallic & Nonmetallic Raceway Systems (EMT, PVC, RMC, FMC) 9.4 Cabinets, Cutout Boxes & Outlet Box Installation Rules (Articles 312 & 314)
10 Chapter 10: Equipment for General Use: Devices, Luminaires & Appliances
10.1 Switches, Receptacles & Device Installation Standards (Articles 404 & 406) 10.2 Luminaire Clearances, Closet Rules & Lighting Track (Article 410) 10.3 Household Appliances & Fixed Electric Space Heating (Articles 422 & 424) 10.4 Generators, Transformer Overcurrent Protection & Panelboards
11 Chapter 11: Motors, Motor Circuits & Controllers
11.1 Motor Nameplate vs. Table FLC & Branch Circuit Conductor Sizing 11.2 Branch Circuit Short-Circuit & Ground-Fault Protection (Table 430.52) 11.3 Motor Overload Protection Sizing & Selection (NEC 430 Part III) 11.4 Motor Disconnects, Controllers & Multimotor Feeder Calculations
12 Chapter 12: Special Occupancies & Hazardous Locations
12.1 Hazardous (Classified) Locations: Classes, Divisions, Zones & Seals 12.2 Commercial Garages, Repair Hangars & Fuel Dispensing Facilities 12.3 Health Care Facilities: Patient Care Spaces & Redundant Grounding (Article 517) 12.4 Agricultural Buildings, Marinas, Boatyards & RV Parks
13 Chapter 13: Special Equipment, Emergency Systems & Renewable Energy
13.1 Swimming Pools, Spas, Hot Tubs & Equipotential Bonding (Article 680) 13.2 Electric Vehicle Supply Equipment (EVSE) Installation & Sizing (Article 625) 13.3 Solar Photovoltaic (PV) Systems & Energy Storage Systems (Articles 690 & 706) 13.4 Emergency, Standby Power Systems & Fire Pumps (Articles 700, 701, 702 & 695) 13.5 Fire Alarm, Optical Fiber & Power-Limited Circuits (Articles 760, 770 & 800)
1.4 NEC Article 90 Scope, Code Arrangement & Article 110 General Requirements
Key Takeaways Explain This Topic AI
NEC Article 90 establishes that the code's sole purpose is the practical safeguarding of persons and property from hazards arising from the use of electricity, serving as an enforceable safety standard rather than a design specification or instruction manual.
The NEC is arranged such that Chapters 1–4 apply generally to all installations; Chapters 5, 6, and 7 modify or supplement Chapters 1–4 for special occupancies, equipment, and conditions; and Chapter 8 (Communications) remains independent unless specifically referenced.
NEC 110.3(B) mandates that listed or labeled equipment must be installed and used in strict accordance with any instructions included in the listing or labeling, making manufacturer installation manuals legally binding code requirements.
NEC Table 110.26(A)(1) governs working space depth in front of electrical equipment operating at 600V or less under Conditions 1 (3 ft), 2 (3 ft to 3.5 ft), and 3 (3 ft to 4 ft), while 110.26(A)(2) and (A)(3) mandate a minimum 30-inch width and 6.5-foot headroom.
Large equipment rated 1200 amperes or more and over 6 feet wide containing overcurrent, switching, or control devices requires two egress doors (or a continuous unobstructed path) equipped with panic hardware that open in the direction of egress (NEC 110.26(C)).
Last updated: August 2026
1.4 NEC Article 90 Scope, Code Arrangement & Article 110 General Requirements
The National Electrical Code (NEC / NFPA 70) establishes the engineering, installation, and safety benchmarks for electrical systems across the United States. To navigate the Code accurately and resolve legal installation questions, a journeyman must understand the philosophical foundation and structural framework outlined in Article 90 , as well as the universal baseline installation mandates codified in Article 110 .
1. NEC Article 90: Purpose, Scope & Legal Philosophy
Article 90 serves as the administrative preamble to the National Electrical Code. It articulates what the Code is, what it is not, and precisely which installations fall within its legal boundary. +-----------------------------------------------------------------------------+
- | NEC ARTICLE 90 FOUNDATIONS |
- | |
- | [90.1 PURPOSE] |
- | * Practical safeguarding of persons and property from electrical hazards. |
- | * NOT an instruction manual or design specification for untrained persons.|
- | * Compliance results in an installation essentially free from hazard, |
- | but not necessarily efficient, convenient, or adequate for good service.||
- | |
- | [90.2 COVERED INSTALLATIONS] [90.2 EXCLUDED INSTALLATIONS] |
- | * Public and private premises, yards * Ships, watercraft, boats |
- | * Parking lots, carnivals, events * Railway rolling stock, trains |
- | * Commercial & industrial substations * Aircraft, space vehicles |
- | * Installations connected to utility * Automotive vehicles |
- | * Mobile homes, RV parks, floating bldgs * Underground mining equipment |
- | * Utility-owned generation / |
- | transmission / distribution |
- +-----------------------------------------------------------------------------+
- Mandatory vs. Permissive Code Rules (NEC 90.5)
The NEC utilizes strict linguistic conventions to distinguish legally enforceable mandates from optional allowances:
Mandatory Rules (90.5(A)): Characterized by the terms "shall" or "shall not" . These rules are compulsory requirements where no deviations are permitted without formal AHJ variance.
Permissive Rules (90.5(B)): Characterized by the terms "shall be permitted" or "shall not be required" . These grant permission to use specified materials or wiring methods, or identify express exceptions to mandatory requirements.
Explanatory Material (90.5(C)): Informational Notes (designated as Informational Note: ... ) contain non-mandatory explanatory text, engineering references, or cross-citations to other standards. Informational notes are not legally enforceable rules .
2. Code Structural Matrix & Chapter Hierarchy (NEC 90.3)
Understanding how code chapters interact is essential for solving complex exam questions where rules appear to conflict. +-----------------------------------------------------------------------------+
- | THE NEC 90.3 CODE ARRANGEMENT MATRIX |
- | |
- | +-----------------------------------------------------------------+ |
- | | CHAPTERS 1, 2, 3, 4: GENERAL APPLICATION | |
- | | - Chapter 1: General (Definitions, Requirements 110) | |
- | | - Chapter 2: Wiring and Protection (210, 215, 220, 240, 250) | |
- | | - Chapter 3: Wiring Methods and Materials (300, 310, 314, 334)| |
- | | - Chapter 4: Equipment for General Use (400, 404, 406, 430) | |
- | +-----------------------------------------------------------------+ |
- | | |
- | +--------------------+--------------------+ |
- | | | |
- | v v |
- | +---------------------------+ +---------------------------+ |
- | | CHAPTERS 5, 6, 7: | | CHAPTER 8: | |
- | | SPECIAL APPLICATIONS | | COMMUNICATIONS SYSTEMS | |
- | | - Ch. 5: Special Places | | - Standalone chapter | |
- | | - Ch. 6: Special Equip | | - Independent of Ch. 1-7 | |
- | | - Ch. 7: Special Cond | | - Ch. 1-7 DO NOT apply | |
- | | (Modify or supplement | | unless Chapter 8 | |
- | | Chapters 1 through 4) | | specifically references| |
- | +---------------------------+ +---------------------------+ |
- | | |
- | v |
- | +-----------------------------------------------------------------+ |
- | | CHAPTER 9: TABLES (Conduit Fill, Conductor Properties) | |
- | | - Legally enforceable engineering tables (Tables 1, 4, 5, 8) | |
- | +-----------------------------------------------------------------+ |
- | | |
- | v |
- | +-----------------------------------------------------------------+ |
- | | INFORMATIVE ANNEXES A THROUGH K: NON-MANDATORY GUIDANCE | |
- | +-----------------------------------------------------------------+ |
- +-----------------------------------------------------------------------------+
- 3. Article 110: General Installation Mandates
Article 110 contains foundational rules governing electrical installations regardless of occupancy type.
1. Equipment Listing, Labeling & Instructions (NEC 110.3(B))
NEC 110.3(B) is one of the most frequently cited rules in electrical enforcement: "Listed or labeled equipment shall be installed and used in accordance with any instructions included in the listing or labeling."
If a manufacturer's UL/CSA installation manual specifies a maximum 20A circuit breaker for an air handler, installing a 30A breaker violates 110.3(B) even if standard branch-circuit conductor rules might permit larger overcurrent protection.
Terminal torque specifications, conductor temperature ratings, and mounting clearances printed in product instructions carry full legal code authority.
2. Mechanical Execution of Work (NEC 110.12)
Electrical equipment must be installed in a neat and workmanlike manner :
Closing Unused Openings (110.12(A)): Unused knockout openings in boxes, cabinets, and panelboards must be effectively closed with listed knockout seals/plugs to afford protection substantially equivalent to the wall of the enclosure.
Subsurface Damage Protection: Cables and raceways behind panels must be routed cleanly to prevent mechanical pinch points, sharp bends, or physical abrasion.
Integrity of Electrical Equipment (110.12(B)): Internal parts of electrical equipment (such as busbars, terminals, and breakers) must not be contaminated by foreign materials like paint, plaster, drywall dust, cleaners, or abrasives.
3. Electrical Connections & Mandatory Torque Tools (NEC 110.14(D))
Loose electrical terminations are a primary cause of electrical fires and arc-fault hazards.
Mandatory Calibrated Torque Tools: NEC 110.14(D) requires that where a tightening torque is indicated as a numeric value on equipment or in installation instructions, a calibrated torque tool (torque wrench or torque screwdriver) shall be used to achieve the indicated torque value.
Temperature Limitations (110.14(C)): Termination temperature ratings dictate conductor ampacity selection:
Equipment rated 100 amperes or less (or terminals for #14 AWG through #1 AWG conductors) is rated for 60°C conductors , unless listed and marked for 75°C.
Equipment rated over 100 amperes (or terminals for conductors larger than #1 AWG) is rated for 75°C conductors .
Higher temperature rated conductors (e.g., 90°C THHN) may be used for ampacity adjustment and correction derating, but the final derated ampacity cannot exceed the temperature rating of the termination.
4. Spaces About Electrical Equipment (NEC 110.26)
NEC 110.26 establishes mandatory working clearances around electrical equipment operating at 600 volts nominal or less (including panelboards, switchboards, disconnect switches, and motor control centers) to permit ready access and safe operation/maintenance. +-----------------------------------------------------------------------------+
- | NEC 110.26 WORKING SPACE 3D ENVELOPE |
- | |
- | +-----------------------+ |
- | | CEILING / 6.5 FT | |
- | +-----------------------+ |
- | | |
- | v |
- | +-------------------------------------+ |
- | | DEDICATED ELECTRICAL SPACE | |
- | | (Floor to 6 ft above equipment or | |
- | | structural ceiling; NO foreign | |
- | | piping, ducts, or leak systems) | |
- | +-------------------------------------+ |
- | | |
- | v |
- | +-------------------------------------+ |
- | | PANELBOARD / SWITCHBOARD | |
- | +-------------------------------------+ |
- | | |
- | v |
- | <----------------------- WIDTH: MINIMUM 30" --------------------------> |
- | (Or the width of the equipment, whichever is greater; doors open 90°) |
- | |
- | <====================== DEPTH: 3.0' TO 4.0' =========================> |
- | (Determined by Table 110.26(A)(1) Conditions 1, 2, or 3) |
- | |
- | [FLOOR LEVEL] ----------------------------------------------------------- |
- | (Working space must be clear, level, and unobstructed from floor to 6.5') |
- +-----------------------------------------------------------------------------+
- Working Space Dimensions Breakdown
- Clearance Dimension NEC Section Statutory Clearance Requirement
- Working Depth 110.26(A)(1) 3.0 ft to 4.0 ft depending on voltage to ground and Condition (see Table below)
Working Width 110.26(A)(2) Minimum 30 inches or the exact width of the equipment (whichever is greater). Equipment does not need to be centered in space. In all cases, equipment doors or hinged panels must open at least 90 degrees .
Working Height (Headroom) 110.26(A)(3) Minimum 6.5 feet (6 ft 6 in.) from the floor, or the height of the equipment (whichever is greater). (Exception: Service equipment or panelboards in existing dwelling units rated 200A or less are permitted lower headroom where approved) .
Dedicated Electrical Space 110.26(E) Extends from the floor to 6.0 feet above the equipment (or to the structural ceiling). No foreign piping, HVAC ducts, sewer lines, or leak protection apparatus may occupy this zone.
NEC Table 110.26(A)(1) Working Depth Matrix Condition 1: Exposed live parts on one side and no live or grounded parts on the other side
(or live parts on both sides effectively guarded by wood/insulating materials).
Condition 2: Exposed live parts on one side and grounded parts on the other side
(Concrete, brick, tile, and grounded metal walls count as grounded surfaces).
Condition 3: Exposed live parts on both sides of the workspace (unshielded/unguarded).
Nominal Voltage to Ground Condition 1 (Insulated Opposite) Condition 2 (Grounded Wall Opposite) Condition 3 (Live Parts Opposite)
- 0 – 150 Volts (e.g., 120/240V single-phase, 208Y/120V) 3.0 feet (914 mm) 3.0 feet (914 mm) 3.0 feet (914 mm)
- 151 – 600 Volts (e.g., 480Y/277V, 480V 3-phase) 3.0 feet (914 mm) 3.5 feet (1.07 m) 4.0 feet (1.22 m)
Warning
Concrete and Masonry Walls are Grounded: For exam calculations involving a 480Y/277V panel facing a concrete basement wall or masonry block, the installation is classified as Condition 2 . Because 277V to ground exceeds 150V, Table 110.26(A)(1) mandates a depth of 3.5 feet (42 inches) , not 3.0 feet.
5. Large Equipment Working Spaces & Room Egress (NEC 110.26(C))
Special life-safety hazards occur in large electrical rooms where high-energy arc flash events can trap personnel. +-----------------------------------------------------------------------------+
- | LARGE EQUIPMENT ENTRANCE & EGRESS RULES (110.26(C)) |
- | |
- | [THRESHOLD FOR "LARGE EQUIPMENT"] |
- | * Equipment rated 1,200 Amperes or More |
- | * AND Over 6.0 Feet (1.8 m) in Width |
- | * Containing overcurrent devices, switching devices, or control devices |
- | |
- | [MANDATORY EGRESS CRITERIA] |
- | 1. TWO Entrance/Egress Doors located at opposite ends of the room. |
- | (Exception: A single door is permitted if the working space depth is |
- | doubled, OR a continuous unobstructed egress path exists). |
- | 2. Personnel Doors within 25 Feet of working space must: |
- | - Open in the direction of egress (SWING OUTWARD away from room). |
- | - Be equipped with listed PANIC HARDWARE or fire exit hardware that |
- | opens under simple pressure (no turn knobs or twisting latches). |
- +-----------------------------------------------------------------------------+