Study guide
7.2 Grounding Electrodes & Grounding Electrode Conductor (GEC) Sizing
Idaho Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Orientation, NEC Navigation & Idaho Regulations
1.1 Idaho Journeyman Exam Format, PSI Logistics & Rapid NEC Navigation 1.2 Idaho Electrical Licensing Laws (Title 54, Ch. 10) & IDAPA 24.39.10 Requirements 1.3 Idaho Permits, Inspection Procedures & State-Specific NEC Amendments 1.4 NEC Article 90 Scope, Code Arrangement & Article 110 General Requirements
2 Chapter 2: Electrical Theory & Essential Math Calculations
2.1 Ohm's Law, Joule's Law & DC Circuit Calculations 2.2 Single-Phase & Three-Phase AC Fundamentals and Power Factor 2.3 DC & AC Voltage Drop Calculations and Conductor Sizing 2.4 NEC Article 100 Essential Definitions for Journeymen
3 Chapter 3: Conductors, Raceways & Box Sizing Calculations
3.1 Conductor Ampacity, Insulation Types & Terminal Temperature Ratings 3.2 Ambient Temperature Correction & Raceway Conductor Bundling Derating 3.3 Outlet & Junction Box Volume Fill Calculations (NEC 314.16) 3.4 Conduit Fill Calculations & Large Pull Box Sizing (NEC 314.28)
4 Chapter 4: Branch Circuits & Overcurrent Protection
4.1 Branch Circuit Ratings, Multiwire Circuits & Receptacle Placement 4.2 GFCI & AFCI Protection Mandates and Idaho Code Clarifications 4.3 Overcurrent Protective Devices, Standard Ratings & Small Conductor Rules 4.4 Feeder & Transformer Tap Rules (NEC 240.21)
5 Chapter 5: Feeders, Services & Outside Branch Circuits
5.1 Feeder Conductor Sizing, Neutral Calculations & Voltage Drop 5.2 Outside Branch Circuits, Feeders & Overhead/Underground Clearances 5.3 Service Drop, Service Lateral & Service-Entrance Sizing 5.4 Service Disconnecting Means, Emergency Disconnects & Surge Protection
6 Chapter 6: Load Calculations: Dwellings & Commercial
6.1 General Lighting, Small Appliance & Laundry Load Calculations 6.2 Standard Method Single-Family Dwelling Service Calculations (NEC 220 Part III) 6.3 Optional Method Single-Family & Multifamily Calculations (NEC 220 Part IV) 6.4 Commercial & Industrial Feeder/Service Calculations
7 Chapter 7: Grounding and Bonding: Systems & Electrodes
7.1 Grounding vs. Bonding Fundamentals & System Grounding 7.2 Grounding Electrodes & Grounding Electrode Conductor (GEC) Sizing 7.3 Main Bonding Jumpers, System Bonding Jumpers & Supply-Side Bonding
8 Chapter 8: Grounding and Bonding: Equipment & Enclosures
8.1 Equipment Grounding Conductors (EGC) Types, Installation & Sizing (Table 250.122) 8.2 Separately Derived Systems (SDS) Transformers & Generator Grounding 8.3 Service Enclosure Bonding, Concentric Knockouts & Effective Ground-Fault Path
9 Chapter 9: Wiring Methods, Cables & Conduits
9.1 General Requirements for Wiring Methods & Underground Installations (Article 300) 9.2 Nonmetallic-Sheathed (NM), Metal-Clad (MC) & Armored (AC) Cables 9.3 Metallic & Nonmetallic Raceway Systems (EMT, PVC, RMC, FMC) 9.4 Cabinets, Cutout Boxes & Outlet Box Installation Rules (Articles 312 & 314)
10 Chapter 10: Equipment for General Use: Devices, Luminaires & Appliances
10.1 Switches, Receptacles & Device Installation Standards (Articles 404 & 406) 10.2 Luminaire Clearances, Closet Rules & Lighting Track (Article 410) 10.3 Household Appliances & Fixed Electric Space Heating (Articles 422 & 424) 10.4 Generators, Transformer Overcurrent Protection & Panelboards
11 Chapter 11: Motors, Motor Circuits & Controllers
11.1 Motor Nameplate vs. Table FLC & Branch Circuit Conductor Sizing 11.2 Branch Circuit Short-Circuit & Ground-Fault Protection (Table 430.52) 11.3 Motor Overload Protection Sizing & Selection (NEC 430 Part III) 11.4 Motor Disconnects, Controllers & Multimotor Feeder Calculations
12 Chapter 12: Special Occupancies & Hazardous Locations
12.1 Hazardous (Classified) Locations: Classes, Divisions, Zones & Seals 12.2 Commercial Garages, Repair Hangars & Fuel Dispensing Facilities 12.3 Health Care Facilities: Patient Care Spaces & Redundant Grounding (Article 517) 12.4 Agricultural Buildings, Marinas, Boatyards & RV Parks
13 Chapter 13: Special Equipment, Emergency Systems & Renewable Energy
13.1 Swimming Pools, Spas, Hot Tubs & Equipotential Bonding (Article 680) 13.2 Electric Vehicle Supply Equipment (EVSE) Installation & Sizing (Article 625) 13.3 Solar Photovoltaic (PV) Systems & Energy Storage Systems (Articles 690 & 706) 13.4 Emergency, Standby Power Systems & Fire Pumps (Articles 700, 701, 702 & 695) 13.5 Fire Alarm, Optical Fiber & Power-Limited Circuits (Articles 760, 770 & 800)
7.2 Grounding Electrodes & Grounding Electrode Conductor (GEC) Sizing
Key Takeaways Explain This Topic AI
Under NEC 250.50, all grounding electrodes present at each building or structure (metal underground water pipes, building steel, concrete-encased electrodes, ground rings, rod/pipe electrodes, and plate electrodes) must be bonded together to form the Grounding Electrode System (GES).
A concrete-encased electrode (Ufer ground, NEC 250.52(A)(3)) requires at least 20 feet of 1/2-inch bare/galvanized rebar or 4 AWG bare copper wire encased in >= 2 inches of concrete located near the bottom of a foundation in direct contact with earth.
Under NEC 250.53(A)(2), a single rod, pipe, or plate electrode must be supplemented by an additional electrode spaced at least 6 feet apart unless proven to have a resistance to earth of 25 ohms or less.
Grounding Electrode Conductors (GECs) are sized from NEC Table 250.66 based on the circular mil area of the largest ungrounded service-entrance conductor or equivalent area for parallel conductors.
NEC 250.66(A), (B), and (C) establish maximum conductor size caps: a GEC connecting solely to rod/pipe/plate electrodes never needs to exceed 6 AWG copper, to a concrete-encased electrode never needs to exceed 4 AWG copper, and to a ground ring never needs to exceed the size of the ring conductor.
Last updated: August 2026
7.2 Grounding Electrodes & Grounding Electrode Conductor (GEC) Sizing
The Grounding Electrode System (GES) establishes the physical, direct connection between the premises electrical installation and the earth. Sizing and installing the Grounding Electrode Conductor (GEC) and interconnecting all available grounding electrodes is a core domain on the Idaho Journeyman Electrician examination.
NEC 250.50 establishes the overarching mandate: "All grounding electrodes as described in 250.52(A)(1) through (A)(7) that are present at each building or structure served shall be bonded together to form the grounding electrode system." +-----------------------------------------------------------------------------+
- | GROUNDING ELECTRODE SYSTEM ARCHITECTURE (NEC 250.50) |
- | |
- | +---------------------------+ |
- | | SERVICE EQUIPMENT / PANEL | |
- | +-------------+-------------+ |
- | | |
- | +-----------------------------+-----------------------------+ |
- | | | | |
- | v (NEC 250.52(A)(1)) v (NEC 250.52(A)(3)) v (A)(5) |
- | +-------------------+ +-------------------+ +-----------------+ |
- | | METAL WATER PIPE | | CONCRETE-ENCASED | | DRIVEN GROUND | |
- | | (>= 10 ft in soil)| | UFER (20 ft Rebar)| | RODS (>= 8 ft) | |
- | | Bond w/in 5 ft of | | Cap: Max #4 Cu | | (2 Rods @ 6 ft) | |
- | | entrance (250.68) | | (NEC 250.66(B)) | | Cap: Max #6 Cu | |
- | +-------------------+ +-------------------+ +-----------------+ |
- +-----------------------------------------------------------------------------+
- 1. Recognized Grounding Electrodes (NEC 250.52(A))
The NEC recognizes seven distinct types of grounding electrodes under NEC 250.52(A) . If any of these electrodes are present on the premises, they must be bonded into the grounding electrode system. +-----------------------------------------------------------------------------+
- | NEC 250.52(A) RECOGNIZED GROUNDING ELECTRODES |
- | |
- | 1. METAL UNDERGROUND WATER PIPE (250.52(A)(1)): |
- | - Minimum 10 ft in direct contact with earth |
- | - Must be supplemented by a second electrode (NEC 250.53(D)(2)) |
- | - Connection must be made within 5 ft of building entrance (250.68(C)) |
- | |
- | 2. METAL IN-GROUND SUPPORT STRUCTURE / BUILDING STEEL (250.52(A)(2)): |
- | - Structural metal frame in direct contact with earth >= 10 ft, OR |
- | - Encased in concrete in direct contact with earth |
- | |
- | 3. CONCRETE-ENCASED ELECTRODE / UFER GROUND (250.52(A)(3)): |
- | - Minimum 20 ft of >= 1/2 in. bare/galvanized rebar, OR |
- | - Minimum 20 ft of bare copper conductor not smaller than 4 AWG |
- | - Encased in >= 2 in. of concrete near bottom of foundation in earth |
- | |
- | 4. GROUND RING (250.52(A)(4)): |
- | - Minimum 20 ft of bare copper conductor not smaller than 2 AWG |
- | - Buried at depth >= 30 in. below grade encircling the building |
- | |
- | 5. ROD AND PIPE ELECTRODES (250.52(A)(5)): |
- | - Minimum 8 ft (2.44 m) in contact with soil |
- | - Steel/iron rods >= 5/8 in. diameter (or listed 1/2 in. copper-clad) |
- | - 25-Ohm Rule: Must add 2nd rod spaced >= 6 ft apart if > 25 ohms |
- | |
- | 6. OTHER LISTED ELECTRODES (250.52(A)(6)): |
- | - Chemically charged ground rods or engineered grounding systems |
- | |
- | 7. PLATE ELECTRODES (250.52(A)(7)): |
- | - Minimum 2 sq ft of surface exposed to soil |
- | - Bare/galvanized iron or steel >= 1/4 in. thick (copper >= 0.06 in.) |
- | - Buried >= 30 in. below grade |
- +-----------------------------------------------------------------------------+
- Detailed Analysis of Critical Electrodes
- 1. Metal Underground Water Pipe (NEC 250.52(A)(1))
Length Requirement: Must have at least 10 feet (3.0 m) of metal pipe in direct contact with the earth.
Mandatory Supplemental Electrode (NEC 250.53(D)(2)): A metal underground water pipe electrode must always be supplemented by an additional electrode (such as a concrete-encased electrode, building steel, ground ring, or rod electrode).
Interior Piping Connection Limitation (NEC 250.68(C)(1)): The bonding connection to the interior metal water piping system must be made within 5 feet (1.52 m) of the point where the water pipe enters the building. Beyond 5 feet, interior metal water piping cannot be used as a conductor to interconnect other electrodes because plastic water meters, filtration systems, or future plumbing repairs with PEX/PVC could disrupt electrical continuity.
2. Concrete-Encased Electrode / "Ufer Ground" (NEC 250.52(A)(3))
Named after wartime engineer Herbert G. Ufer, concrete-encased electrodes are considered the most effective, durable grounding electrodes in modern construction.
Conductor Specifications: Must consist of at least 20 feet (6.0 m) of either:
One or more bare or zinc-galvanized steel reinforcing bars (rebar) not less than 1/2 inch (13 mm) in diameter (standard #4 rebar), bonded together by standard steel tie wires, OR
Bare copper conductor not smaller than 4 AWG .
Placement: Encased by at least 2 inches (50 mm) of concrete, located horizontally near the bottom or vertically within a concrete foundation or footing that is in direct contact with the earth.
Mandatory Inclusion: Under NEC 250.50, if a concrete-encased electrode is present in a newly poured footing or foundation, it must be bonded to the electrical service. Failing to extend a conductor out of the footing prior to pouring is a major code violation.
3. Rod and Pipe Electrodes & The 25-Ohm Rule (NEC 250.52(A)(5) & 250.53(A)(2))
Physical Dimensions: Rod electrodes must be at least 8 feet (2.44 m) in length. Unlisted iron or steel rods must be at least 5/8 in. (15.87 mm) in diameter. Listed stainless steel or copper-coated steel rods must have a diameter of not less than 1/2 in. (12.7 mm) .
Installation Depth: Must be driven vertically to a depth of not less than 8 feet. Where rock bottom is encountered, the rod is permitted to be driven at an angle not exceeding 45 degrees from the vertical, or buried in a trench at least 30 inches (750 mm) deep (NEC 250.53(G)).
The 25-Ohm Rule (NEC 250.53(A)(2)): If a single rod, pipe, or plate electrode does not have a resistance to earth of 25 ohms or less , it must be supplemented by an additional electrode from 250.52(A)(2) through (A)(8).
Rod Separation (NEC 250.53(A)(3)): Supplemental rod electrodes must be installed at least 6 feet (1.8 m) apart. (Engineering best practice is spacing equal to twice the rod length, or 16 feet, to eliminate overlapping resistance spheres of influence).
The "Two-Rod Rule": If two rod electrodes are installed at least 6 feet apart, no resistance testing is required under the NEC, even if the total combined resistance exceeds 25 ohms!
2. Prohibited Grounding Electrodes (NEC 250.52(B))
Under NEC 250.52(B) , the following systems are strictly prohibited from being used as grounding electrodes:
Metal Underground Gas Piping Systems: Electric arc currents during lightning or fault conditions could ignite gas or puncture underground gas piping, causing explosions.
Aluminum: Aluminum corrodes rapidly when placed in direct contact with soil or masonry, leading to complete degradation of electrical continuity.
3. Intersystem Bonding Termination (IBT) (NEC 250.94)
NEC 250.94 mandates that an Intersystem Bonding Termination (IBT) device be provided external to enclosures at the service equipment or metering equipment. +-----------------------------------------------------------------------------+
- | INTERSYSTEM BONDING TERMINATION (NEC 250.94) |
- | |
- | [SERVICE DISCONNECT / METER BASE] |
- | +-------------------------------+ |
- | | Grounding Electrode Conductor | |
- | +---------------+---------------+ |
- | | |
- | v |
- | +-------------------------------+ 1. Telephone / Broadband Ground Wire |
- | | INTERSYSTEM BONDING BLOCK |== 2. Cable TV (CATV) Coaxial Shield |
- | | (Minimum 3 Terminals for #14 |== 3. Satellite Dish Ground Wire |
- | | through #6 AWG Conductors) |== 4. Network Communications System |
- | +-------------------------------+ |
- +-----------------------------------------------------------------------------+
Key IBT Requirements:
Must be accessible on the exterior of the service enclosure.
Must have capacity for connection of not less than three (3) intersystem bonding conductors .
Accepts copper conductors ranging from 14 AWG to 6 AWG .
Ensures that television cable, telephone, satellite dish, and communications systems share the exact same earth reference potential, preventing dangerous circulating shield currents and lightning damage.
4. Sizing the Grounding Electrode Conductor (NEC Table 250.66)
The Grounding Electrode Conductor (GEC) is sized exclusively using NEC Table 250.66 based on the cross-sectional area of the largest ungrounded service-entrance conductor (or the equivalent total circular mil area for parallel conductors per phase). +-----------------------------------------------------------------------------+
- | NEC TABLE 250.66: GROUNDING ELECTRODE CONDUCTOR SIZING |
- | |
- | LARGEST UNGROUNDED SERVICE | MINIMUM SIZE OF GEC |
- | ENTRANCE CONDUCTOR (OR PARALLEL) |------------------------------------- |
- | COPPER ALUMINUM | COPPER (Cu) | ALUMINUM (Al) |
- | --------------------+-------------+-------------------+----------------- |
- | 2 AWG or smaller | 1/0 or smaller| 8 AWG | 6 AWG |
- | 1 AWG or 1/0 AWG | 2/0 or 3/0 | 6 AWG | 4 AWG |
- | 2/0 AWG or 3/0 AWG | 4/0 or 250 | 4 AWG | 2 AWG |
- | Over 3/0 - 350 kcmil| Over 250-500| 2 AWG | 1/0 AWG |
- | Over 350 - 600 kcmil| Over 500-900| 1/0 AWG | 3/0 AWG |
- | Over 600 - 1100 kcmil|Over 900-1750| 2/0 AWG | 4/0 AWG |
- | Over 1100 kcmil | Over 1750 | 3/0 AWG | 250 kcmil |
- +-----------------------------------------------------------------------------+
- Special Conductor Size Caps (NEC 250.66(A), (B), and (C))
While Table 250.66 dictates the general GEC size based on service conductors, the NEC provides maximum size limitations (caps) when the GEC connects solely to specific individual electrode types: +-----------------------------------------------------------------------------+
- | GEC MAXIMUM SIZE CAPS (NEC 250.66(A), (B), (C)) |
- | |
- | [ROD, PIPE, OR PLATE ELECTRODES - NEC 250.66(A)] |
- | * Sole connection to rod, pipe, or plate NEVER requires a GEC |
- | larger than: #6 AWG COPPER or #4 AWG ALUMINUM |
- | * Rationale: Soil contact resistance limits current; larger wire is wasted.|
- | |
- | [CONCRETE-ENCASED UFER ELECTRODE - NEC 250.66(B)] |
- | * Sole connection to concrete-encased electrode NEVER requires a GEC |
- | larger than: #4 AWG COPPER |
- | * Rationale: Internal rebar/wire capacity is matched to #4 Cu. |
- | |
- | [GROUND RING ELECTRODE - NEC 250.66(C)] |
- | * Sole connection to a ground ring NEVER requires a GEC larger than |
- | the conductor size used for the ground ring itself (minimum #2 Cu). |
- +-----------------------------------------------------------------------------+
Caution
Exam Trap Alert: Sole Connection vs. Table 250.66! If an exam question asks: "What size copper GEC is required for a 2,000A service (parallel 500 kcmil conductors) connected solely to two driven ground rods?"
Based strictly on Table 250.66, you might mistakenly select 3/0 AWG Cu.
The correct answer is #6 AWG Copper under NEC 250.66(A)! The size cap applies regardless of how massive the service conductors are.
However, if the GEC connects to a metal water pipe or building steel , Table 250.66 MUST be used in full without any size cap!
- 5. Step-by-Step Worked Sizing Calculations
- Worked Example 1: 200-Ampere Residential Service
Scenario: A single-family residence is served by 2/0 AWG Copper THHN service-entrance conductors. The grounding electrode system consists of an underground metal water pipe and two supplemental driven ground rods. Determine the required copper GEC sizes. Step 1: Size GEC to the Metal Underground Water Pipe
- Water pipe is a Table 250.66 electrode (no cap).
- Look up 2/0 AWG Copper in NEC Table 250.66:
* Service conductor = 2/0 AWG Cu -> Table 250.66 requires #4 AWG Copper GEC.
Step 2: Size GEC to the Driven Ground Rods
- Driven rod is governed by NEC 250.66(A) (sole connection cap).
- For 2/0 AWG Cu service, Table 250.66 gives #4 AWG, but 250.66(A) caps the requirement at #6 AWG Copper.
- Therefore, a #6 AWG Copper conductor is permitted from the panel (or from the water pipe bond) to the ground rods.
Worked Example 2: 800-Ampere Commercial Service with Parallel Conductors
Scenario: An 800A commercial service consists of three parallel conduits per phase, each containing 350 kcmil Copper conductors. The building includes structural building steel, a concrete-encased Ufer ground, and driven ground rods. Determine the minimum copper GEC size for each electrode. Step 1: Determine Total Circular Mil Area per Phase
- Each phase contains three 350 kcmil conductors in parallel.
- Total Phase Area = 3 x 350 kcmil = 1,050 kcmil Copper.
Step 2: Size GEC to Structural Building Steel (Table 250.66)
- Building steel has no conductor cap.
- Look up 1,050 kcmil Cu in Table 250.66 (Row: "Over 600 kcmil thru 1,100 kcmil"):
- Required GEC to Building Steel = 2/0 AWG Copper.
Step 3: Size GEC to Concrete-Encased Electrode (NEC 250.66(B))
- Under 250.66(B), connection to Ufer ground is capped at #4 AWG Copper.
- Required GEC to Ufer Ground = #4 AWG Copper.
Step 4: Size GEC to Driven Ground Rods (NEC 250.66(A))
- Under 250.66(A), connection to ground rods is capped at #6 AWG Copper.
- Required GEC to Rod Electrodes = #6 AWG Copper.