Study guide
11.4 Motor Disconnects, Controllers & Multimotor Feeder Calculations
Idaho Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Orientation, NEC Navigation & Idaho Regulations
1.1 Idaho Journeyman Exam Format, PSI Logistics & Rapid NEC Navigation 1.2 Idaho Electrical Licensing Laws (Title 54, Ch. 10) & IDAPA 24.39.10 Requirements 1.3 Idaho Permits, Inspection Procedures & State-Specific NEC Amendments 1.4 NEC Article 90 Scope, Code Arrangement & Article 110 General Requirements
2 Chapter 2: Electrical Theory & Essential Math Calculations
2.1 Ohm's Law, Joule's Law & DC Circuit Calculations 2.2 Single-Phase & Three-Phase AC Fundamentals and Power Factor 2.3 DC & AC Voltage Drop Calculations and Conductor Sizing 2.4 NEC Article 100 Essential Definitions for Journeymen
3 Chapter 3: Conductors, Raceways & Box Sizing Calculations
3.1 Conductor Ampacity, Insulation Types & Terminal Temperature Ratings 3.2 Ambient Temperature Correction & Raceway Conductor Bundling Derating 3.3 Outlet & Junction Box Volume Fill Calculations (NEC 314.16) 3.4 Conduit Fill Calculations & Large Pull Box Sizing (NEC 314.28)
4 Chapter 4: Branch Circuits & Overcurrent Protection
4.1 Branch Circuit Ratings, Multiwire Circuits & Receptacle Placement 4.2 GFCI & AFCI Protection Mandates and Idaho Code Clarifications 4.3 Overcurrent Protective Devices, Standard Ratings & Small Conductor Rules 4.4 Feeder & Transformer Tap Rules (NEC 240.21)
5 Chapter 5: Feeders, Services & Outside Branch Circuits
5.1 Feeder Conductor Sizing, Neutral Calculations & Voltage Drop 5.2 Outside Branch Circuits, Feeders & Overhead/Underground Clearances 5.3 Service Drop, Service Lateral & Service-Entrance Sizing 5.4 Service Disconnecting Means, Emergency Disconnects & Surge Protection
6 Chapter 6: Load Calculations: Dwellings & Commercial
6.1 General Lighting, Small Appliance & Laundry Load Calculations 6.2 Standard Method Single-Family Dwelling Service Calculations (NEC 220 Part III) 6.3 Optional Method Single-Family & Multifamily Calculations (NEC 220 Part IV) 6.4 Commercial & Industrial Feeder/Service Calculations
7 Chapter 7: Grounding and Bonding: Systems & Electrodes
7.1 Grounding vs. Bonding Fundamentals & System Grounding 7.2 Grounding Electrodes & Grounding Electrode Conductor (GEC) Sizing 7.3 Main Bonding Jumpers, System Bonding Jumpers & Supply-Side Bonding
8 Chapter 8: Grounding and Bonding: Equipment & Enclosures
8.1 Equipment Grounding Conductors (EGC) Types, Installation & Sizing (Table 250.122) 8.2 Separately Derived Systems (SDS) Transformers & Generator Grounding 8.3 Service Enclosure Bonding, Concentric Knockouts & Effective Ground-Fault Path
9 Chapter 9: Wiring Methods, Cables & Conduits
9.1 General Requirements for Wiring Methods & Underground Installations (Article 300) 9.2 Nonmetallic-Sheathed (NM), Metal-Clad (MC) & Armored (AC) Cables 9.3 Metallic & Nonmetallic Raceway Systems (EMT, PVC, RMC, FMC) 9.4 Cabinets, Cutout Boxes & Outlet Box Installation Rules (Articles 312 & 314)
10 Chapter 10: Equipment for General Use: Devices, Luminaires & Appliances
10.1 Switches, Receptacles & Device Installation Standards (Articles 404 & 406) 10.2 Luminaire Clearances, Closet Rules & Lighting Track (Article 410) 10.3 Household Appliances & Fixed Electric Space Heating (Articles 422 & 424) 10.4 Generators, Transformer Overcurrent Protection & Panelboards
11 Chapter 11: Motors, Motor Circuits & Controllers
11.1 Motor Nameplate vs. Table FLC & Branch Circuit Conductor Sizing 11.2 Branch Circuit Short-Circuit & Ground-Fault Protection (Table 430.52) 11.3 Motor Overload Protection Sizing & Selection (NEC 430 Part III) 11.4 Motor Disconnects, Controllers & Multimotor Feeder Calculations
12 Chapter 12: Special Occupancies & Hazardous Locations
12.1 Hazardous (Classified) Locations: Classes, Divisions, Zones & Seals 12.2 Commercial Garages, Repair Hangars & Fuel Dispensing Facilities 12.3 Health Care Facilities: Patient Care Spaces & Redundant Grounding (Article 517) 12.4 Agricultural Buildings, Marinas, Boatyards & RV Parks
13 Chapter 13: Special Equipment, Emergency Systems & Renewable Energy
13.1 Swimming Pools, Spas, Hot Tubs & Equipotential Bonding (Article 680) 13.2 Electric Vehicle Supply Equipment (EVSE) Installation & Sizing (Article 625) 13.3 Solar Photovoltaic (PV) Systems & Energy Storage Systems (Articles 690 & 706) 13.4 Emergency, Standby Power Systems & Fire Pumps (Articles 700, 701, 702 & 695) 13.5 Fire Alarm, Optical Fiber & Power-Limited Circuits (Articles 760, 770 & 800)
11.4 Motor Disconnects, Controllers & Multimotor Feeder Calculations
Key Takeaways Explain This Topic AI
Under NEC 430.110, motor disconnecting means must have an ampere rating of not less than 115% of the motor Table FLC and must possess a horsepower (HP) rating not less than the motor rating.
Under NEC 430.102, a disconnecting means must be located in sight from the motor controller AND in sight from the motor location and driven machinery (visible and not more than 50 feet away).
Multimotor feeder conductors under NEC 430.24 must have an allowable ampacity of at least 125% of the largest motor Table FLC plus 100% of the sum of all other motor Table FLCs (+ 125% of continuous non-motor loads).
Multimotor feeder short-circuit protection under NEC 430.62 is sized by taking the largest branch protective device rating of any motor in the group and adding the sum of the Table FLCs of all other motors.
CRITICAL CODE RULE: Unlike branch circuits, NEC 430.62 strictly PROHIBITS rounding up when sizing feeder short-circuit protective devices; you must round DOWN to the next lower standard rating in NEC 240.6(A).
Last updated: August 2026
11.4 Motor Disconnects, Controllers & Multimotor Feeder Calculations
In industrial and commercial facilities, multiple motors are frequently powered from a central distribution switchboard or Motor Control Center (MCC). Designing these multi-load installations requires synthesizing multiple sections of NEC Article 430 , including disconnecting means rules (Part IX), motor controller requirements (Part VII), multimotor feeder conductor sizing (Part II), and feeder short-circuit protection (Part X).
This section walks through the complete end-to-end engineering methodology required to size every element of a multimotor installation, emphasizing high-yield licensing exam topics such as the "in sight from" rule , horsepower-rated disconnect criteria, and the critical feeder overcurrent protection round-down rule .
1. Motor Disconnecting Means (NEC Article 430 Part IX)
A motor disconnecting means provides a physical point of electrical isolation to ensure that electricians and maintenance personnel can safely service the motor, controller, and driven machinery without risk of unexpected re-energization. +-----------------------------------------------------------------------------+
- | MOTOR DISCONNECT SIZING & LOCATION RULES |
- | |
- | [RATING REQUIREMENTS (NEC 430.110)] |
- | * Ampere Rating: Minimum 115% of Table FLC (NEC 430.110(A)). |
- | * Horsepower Rating: Must have a marked HP rating not less than the motor |
- | horsepower rating (NEC 430.109). |
- | * Single Disconnect for Motor + Other Loads: Sized for 115% motor FLC + |
- | 100% of non-continuous loads + 125% of continuous non-motor loads. |
- | |
- | [LOCATION REQUIREMENTS (NEC 430.102)] |
- | * Must be IN SIGHT FROM the motor controller (430.102(A)). |
- | * Must be IN SIGHT FROM the motor location & machinery (430.102(B)). |
- | |
- | [DEFINITION OF "IN SIGHT FROM" (ARTICLE 100)] |
- | * The equipment must be VISIBLE AND NOT MORE THAN 50 FEET (15 m) AWAY. |
- +-----------------------------------------------------------------------------+
Exceptions to the Motor Disconnect Rule (NEC 430.102(B) Exception):
A separate disconnect is not required at the motor location if:
Locating the disconnect adjacent to the motor is impracticable or introduces additional hazards (e.g., inside explosive atmospheres, submerged pumps, clean rooms).
In industrial facilities with written safety procedures and qualified personnel, the controller disconnect is individually lockable in the open position in accordance with NEC 110.25 (the locking mechanism must remain in place on the switch whether the padlock is installed or removed; portable lock-out hasps do not satisfy 110.25).
2. Motor Controllers (NEC Article 430 Part VII)
A motor controller is any switch or device normally used to start and stop a motor by making and breaking the motor circuit current. +-----------------------------------------------------------------------------+
- | MOTOR CONTROLLER CATEGORIES |
- | |
- | [1. MANUAL MOTOR STARTERS] |
- | * Manually operated toggle or pushbutton switch with built-in thermal |
- | overload elements (common for small fractional & 1-5 HP equipment). |
- | |
- | [2. MAGNETIC MOTOR STARTERS (ACROSS-THE-LINE / FULL-VOLTAGE)] |
- | * Electromagnetic contactor paired with an overload relay assembly. |
- | * Controlled remotely via start/stop pushbuttons, PLCs, or sensors. |
- | |
- | [3. VARIABLE FREQUENCY DRIVES (VFDs) / INVERTERS (PART X)] |
- | * Converts AC to DC, then synthesizes variable frequency/voltage AC. |
- | * Sizing: VFD input conductors sized at 125% of VFD rated input current |
- | (NEC 430.122). Overload protection is often integrated into VFD logic. |
- +-----------------------------------------------------------------------------+
Controller Horsepower Ratings (NEC 430.83):
Each controller must have a horsepower rating not lower than the horsepower rating of the motor it controls, except:
Stationary Motors <= 1/8 HP: General-use snap switches or branch-circuit breakers permitted.
Stationary Motors <= 2 HP (300V or less): General-use AC snap switch rated for at least twice the motor Table FLC.
3. Multimotor Feeder Conductor Sizing (NEC 430.24)
When a single feeder supplies two or more motors, the feeder conductors must be sized to supply the starting surge of the largest motor while simultaneously carrying the full-load operating current of all remaining motors. +-----------------------------------------------------------------------------+
- | MULTIMOTOR FEEDER CONDUCTOR FORMULA (430.24) |
- | |
- | I_feeder = (1.25 x I_largest) + Sum(I_other motors) + (1.25 x I_cont) + I_noncont |
- | |
- | - I_largest: Table FLC of the single largest motor in the group |
- | - Sum(I_other motors): 100% of Table FLC of all other motors |
- | - I_cont: 125% of any continuous non-motor loads |
- | - I_noncont: 100% of any non-continuous non-motor loads |
- +-----------------------------------------------------------------------------+
Note
Determining the "Largest Motor": The "largest motor" is defined strictly by the highest Table FLC , NOT necessarily the highest marked horsepower. If two or more motors have identical highest FLC ratings, only one of those motors is multiplied by 125%; the other identical motor(s) are added at 100%.
4. Multimotor Feeder Short-Circuit Protection (NEC 430.62)
NEC 430.62(A) dictates that a feeder supplying a specific group of motors must be protected by an overcurrent device with a rating or setting not greater than the largest branch-circuit short-circuit and ground-fault protective device rating of any motor in the group plus the sum of the full-load currents ( Table FLC ) of all other motors supplied by the feeder.
Feeder OCPD Rating <= Largest Branch Protective Device + Sum(FLC of Remaining Motors) +-----------------------------------------------------------------------------+
- | CRITICAL EXAM TRAP: NO ROUNDING UP ON FEEDERS! |
- | |
- | * For Branch Circuits (430.52): If the math gives 148.5 A, you ROUND UP |
- | to 150 A under Exception 1. |
- | |
- | * For Feeders (430.62): If the calculated maximum is 223 A, you |
- | STRICTLY CANNOT ROUND UP TO 225 A! |
- | You MUST round DOWN to the next lower standard rating (200 A). |
- | |
- | NEC 430.62 explicitly establishes a MAXIMUM CEILING. Sizing above this |
- | calculated value is a direct Code violation! |
- +-----------------------------------------------------------------------------+
- 5. Complete End-to-End Industrial Multimotor Feeder Problem
Let us execute a complete, real-world engineering calculation for an industrial motor control center (MCC) subfeeder.
The Problem Specification:
A 460-volt, 3-phase, 60 Hz feeder supplies three continuous-duty squirrel-cage induction motors (Design B, 75°C terminals):
- Motor 1: 50 HP (Table 430.250 FLC = 65.0 A )
- Motor 2: 25 HP (Table 430.250 FLC = 34.0 A )
Motor 3: 10 HP (Table 430.250 FLC = 14.0 A ) +-----------------------------------------------------------------------------+
- | MULTIMOTOR CALCULATION STEP-BY-STEP SOLUTION |
- | |
- | ======================================================================= |
- | STEP 1: SIZE INDIVIDUAL BRANCH CIRCUITS |
- | ======================================================================= |
- | Motor 1 (50 HP, 65.0 A): |
- | - Conductor (430.22): 65.0 A x 1.25 = 81.25 A -> 4 AWG Cu (75°C = 85 A) |
- | - Inverse-Time CB (430.52): 65.0 A x 2.50 = 162.5 A -> Round UP = 175 A |
- | - Time-Delay Fuse (430.52): 65.0 A x 1.75 = 113.75 A -> Round UP = 125 A |
- | - Disconnect (430.110): 65.0 A x 1.15 = 74.75 A -> 50 HP rated switch |
- | |
- | Motor 2 (25 HP, 34.0 A): |
- | - Conductor (430.22): 34.0 A x 1.25 = 42.5 A -> 8 AWG Cu (75°C = 50 A) |
- | - Inverse-Time CB (430.52): 34.0 A x 2.50 = 85.0 A -> Round UP = 90 A |
- | - Time-Delay Fuse (430.52): 34.0 A x 1.75 = 59.5 A -> Round UP = 60 A |
- | - Disconnect (430.110): 34.0 A x 1.15 = 39.1 A -> 25 HP rated switch |
- | |
- | Motor 3 (10 HP, 14.0 A): |
- | - Conductor (430.22): 14.0 A x 1.25 = 17.5 A -> 12 AWG Cu (75°C = 25 A) |
- | - Inverse-Time CB (430.52): 14.0 A x 2.50 = 35.0 A -> Standard = 35 A |
- | - Time-Delay Fuse (430.52): 14.0 A x 1.75 = 24.5 A -> Round UP = 25 A |
- | - Disconnect (430.110): 14.0 A x 1.15 = 16.1 A -> 10 HP rated switch |
- | |
- | ======================================================================= |
- | STEP 2: SIZE MULTIMOTOR FEEDER CONDUCTORS (NEC 430.24) |
- | ======================================================================= |
- | - Identify Largest Motor: Motor 1 (50 HP, Table FLC = 65.0 A). |
- | - Feeder Ampacity = (65.0 A x 1.25) + 34.0 A + 14.0 A |
- | = 81.25 A + 34.0 A + 14.0 A = 129.25 Amperes. |
- | - Table 310.16 (75°C Copper): |
- | * 1 AWG Copper = 130 Amperes (130 A >= 129.25 A). |
- | -> Feeder Conductor Size: 1 AWG Copper (or 1/0 AWG for margin). |
- | |
- | ======================================================================= |
- | STEP 3: SIZE FEEDER SHORT-CIRCUIT PROTECTION (NEC 430.62) |
- | ======================================================================= |
- | [OPTION A: FEEDER INVERSE-TIME CIRCUIT BREAKER] |
- | - Largest Motor Branch Breaker = 175 A (from Motor 1). |
- | - Add FLC of Other Motors = 175 A + 34.0 A + 14.0 A = 223.0 A Max. |
- | - Apply Round-Down Rule: Next lower standard breaker in 240.6(A) <= 223 A |
- | -> Maximum Feeder Breaker = 200 Amperes! (225 A is a Code Violation) |
- | |
- | [OPTION B: FEEDER DUAL-ELEMENT TIME-DELAY FUSES] |
- | - Largest Motor Branch Fuse = 125 A (from Motor 1). |
- | - Add FLC of Other Motors = 125 A + 34.0 A + 14.0 A = 173.0 A Max. |
- | - Apply Round-Down Rule: Standard fuse size in 240.6(A) <= 173 A |
- | -> Maximum Feeder Fuse = 150 Amperes! (175 A is a Code Violation) |
- | |
- | ======================================================================= |
- | STEP 4: SIZE MAIN FEEDER DISCONNECTING MEANS (NEC 430.110(C)) |
- | ======================================================================= |
- | - Minimum Ampere Rating = (65.0 A x 1.15) + 34.0 A + 14.0 A |
- | = 74.75 A + 34.0 A + 14.0 A = 122.75 Amperes. |
- | - Horsepower Rating: Equivalent locked-rotor current sum -> 100 HP switch.|
- +-----------------------------------------------------------------------------+
6. Summary Comparison: Sizing Feeder vs. Branch Circuit Elements +-----------------------------------------------------------------------------+
- | FEEDER VS. BRANCH CIRCUIT MASTER COMPARISON |
- | |
- | Circuit Dimension | Branch Circuit (430.22/52) | Feeder (430.24/62) |
- | :--------------------- | :------------------------- | :------------------ |
- | **Conductor Sizing** | 125% of single motor FLC | 125% largest FLC + |
- | | | 100% sum of others |
- | **Short-Circuit OCPD** | Table 430.52 % of FLC | Largest branch OCPD |
- | | | + sum of other FLCs |
- | **Rounding Rule** | **ROUND UP** to next | **STRICTLY ROUND |
- | | standard rating (240.6(A)) | **DOWN** to lower |
- | **Disconnect Rating** | Min 115% FLC + HP rated | Min 115% sum FLCs |
- +-----------------------------------------------------------------------------+