Study guide
11.1 Motor Nameplate vs. Table FLC & Branch Circuit Conductor Sizing
Idaho Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Orientation, NEC Navigation & Idaho Regulations
1.1 Idaho Journeyman Exam Format, PSI Logistics & Rapid NEC Navigation 1.2 Idaho Electrical Licensing Laws (Title 54, Ch. 10) & IDAPA 24.39.10 Requirements 1.3 Idaho Permits, Inspection Procedures & State-Specific NEC Amendments 1.4 NEC Article 90 Scope, Code Arrangement & Article 110 General Requirements
2 Chapter 2: Electrical Theory & Essential Math Calculations
2.1 Ohm's Law, Joule's Law & DC Circuit Calculations 2.2 Single-Phase & Three-Phase AC Fundamentals and Power Factor 2.3 DC & AC Voltage Drop Calculations and Conductor Sizing 2.4 NEC Article 100 Essential Definitions for Journeymen
3 Chapter 3: Conductors, Raceways & Box Sizing Calculations
3.1 Conductor Ampacity, Insulation Types & Terminal Temperature Ratings 3.2 Ambient Temperature Correction & Raceway Conductor Bundling Derating 3.3 Outlet & Junction Box Volume Fill Calculations (NEC 314.16) 3.4 Conduit Fill Calculations & Large Pull Box Sizing (NEC 314.28)
4 Chapter 4: Branch Circuits & Overcurrent Protection
4.1 Branch Circuit Ratings, Multiwire Circuits & Receptacle Placement 4.2 GFCI & AFCI Protection Mandates and Idaho Code Clarifications 4.3 Overcurrent Protective Devices, Standard Ratings & Small Conductor Rules 4.4 Feeder & Transformer Tap Rules (NEC 240.21)
5 Chapter 5: Feeders, Services & Outside Branch Circuits
5.1 Feeder Conductor Sizing, Neutral Calculations & Voltage Drop 5.2 Outside Branch Circuits, Feeders & Overhead/Underground Clearances 5.3 Service Drop, Service Lateral & Service-Entrance Sizing 5.4 Service Disconnecting Means, Emergency Disconnects & Surge Protection
6 Chapter 6: Load Calculations: Dwellings & Commercial
6.1 General Lighting, Small Appliance & Laundry Load Calculations 6.2 Standard Method Single-Family Dwelling Service Calculations (NEC 220 Part III) 6.3 Optional Method Single-Family & Multifamily Calculations (NEC 220 Part IV) 6.4 Commercial & Industrial Feeder/Service Calculations
7 Chapter 7: Grounding and Bonding: Systems & Electrodes
7.1 Grounding vs. Bonding Fundamentals & System Grounding 7.2 Grounding Electrodes & Grounding Electrode Conductor (GEC) Sizing 7.3 Main Bonding Jumpers, System Bonding Jumpers & Supply-Side Bonding
8 Chapter 8: Grounding and Bonding: Equipment & Enclosures
8.1 Equipment Grounding Conductors (EGC) Types, Installation & Sizing (Table 250.122) 8.2 Separately Derived Systems (SDS) Transformers & Generator Grounding 8.3 Service Enclosure Bonding, Concentric Knockouts & Effective Ground-Fault Path
9 Chapter 9: Wiring Methods, Cables & Conduits
9.1 General Requirements for Wiring Methods & Underground Installations (Article 300) 9.2 Nonmetallic-Sheathed (NM), Metal-Clad (MC) & Armored (AC) Cables 9.3 Metallic & Nonmetallic Raceway Systems (EMT, PVC, RMC, FMC) 9.4 Cabinets, Cutout Boxes & Outlet Box Installation Rules (Articles 312 & 314)
10 Chapter 10: Equipment for General Use: Devices, Luminaires & Appliances
10.1 Switches, Receptacles & Device Installation Standards (Articles 404 & 406) 10.2 Luminaire Clearances, Closet Rules & Lighting Track (Article 410) 10.3 Household Appliances & Fixed Electric Space Heating (Articles 422 & 424) 10.4 Generators, Transformer Overcurrent Protection & Panelboards
11 Chapter 11: Motors, Motor Circuits & Controllers
11.1 Motor Nameplate vs. Table FLC & Branch Circuit Conductor Sizing 11.2 Branch Circuit Short-Circuit & Ground-Fault Protection (Table 430.52) 11.3 Motor Overload Protection Sizing & Selection (NEC 430 Part III) 11.4 Motor Disconnects, Controllers & Multimotor Feeder Calculations
12 Chapter 12: Special Occupancies & Hazardous Locations
12.1 Hazardous (Classified) Locations: Classes, Divisions, Zones & Seals 12.2 Commercial Garages, Repair Hangars & Fuel Dispensing Facilities 12.3 Health Care Facilities: Patient Care Spaces & Redundant Grounding (Article 517) 12.4 Agricultural Buildings, Marinas, Boatyards & RV Parks
13 Chapter 13: Special Equipment, Emergency Systems & Renewable Energy
13.1 Swimming Pools, Spas, Hot Tubs & Equipotential Bonding (Article 680) 13.2 Electric Vehicle Supply Equipment (EVSE) Installation & Sizing (Article 625) 13.3 Solar Photovoltaic (PV) Systems & Energy Storage Systems (Articles 690 & 706) 13.4 Emergency, Standby Power Systems & Fire Pumps (Articles 700, 701, 702 & 695) 13.5 Fire Alarm, Optical Fiber & Power-Limited Circuits (Articles 760, 770 & 800)
11.1 Motor Nameplate vs. Table FLC & Branch Circuit Conductor Sizing
Key Takeaways Explain This Topic AI
Under NEC 430.6(A)(1), conductors, switches, branch-circuit short-circuit and ground-fault protection, and feeder overcurrent protection MUST be sized using the Full-Load Current (FLC) values published in NEC Tables (430.247, 430.248, 430.249, 430.250), NEVER the motor nameplate rating.
Motor nameplate Full-Load Amperes (FLA) is strictly reserved for sizing separate motor overload protection devices under NEC 430.32.
NEC 430.22 requires single-motor branch-circuit conductors supplying a continuous-duty motor to have an allowable ampacity of not less than 125% (1.25) of the motor table FLC.
Conductor sizing for non-continuous duty motors (short-time, intermittent, periodic, varying) must be calculated using the duty-cycle percentages from NEC Table 430.22(E).
Conductor selection must comply with NEC 110.14(C) terminal temperature ratings (60°C for equipment rated 100A or less unless marked 75°C; 75°C for equipment rated over 100A).
Last updated: August 2026
11.1 Motor Nameplate vs. Table FLC & Branch Circuit Conductor Sizing
Electric motors represent one of the most dynamic and heavily tested subjects on the Idaho Journeyman Electrician Examination . Unlike standard resistive or lighting loads, motors exhibit substantial inductive characteristics, severe inrush currents during startup (often 600% or more of normal operating current), and varying operational duty cycles. Consequently, NEC Article 430 establishes a specialized set of engineering and installation rules that diverge significantly from standard branch-circuit calculations.
To successfully design, install, and troubleshoot motor circuits—and to score 100% on motor exam questions—electricians must master the fundamental distinction between Table Full-Load Current (FLC) and Nameplate Full-Load Amperes (FLA) , the mandatory conductor sizing multipliers, duty-cycle adjustments, and terminal temperature ratings.
1. The Fundamental Mandate: NEC 430.6(A)(1) Golden Rule
The most pervasive trap on electrical licensing exams involves selecting the incorrect current value when performing circuit calculations. NEC 430.6(A)(1) establishes an uncompromising divide between when to use the NEC Tables versus when to read the physical motor nameplate. +-----------------------------------------------------------------------------+
- | NEC 430.6(A)(1) CURRENT SELECTION MATRIX |
- | |
- | [USE NEC TABLES: 430.247, 430.248, 430.249, 430.250] |
- | ---------------------------------------------------- |
- | * Branch-Circuit Conductor Sizing (NEC 430.22) |
- | * Multimotor Feeder Conductor Sizing (NEC 430.24) |
- | * Branch Short-Circuit & Ground-Fault Protection (NEC 430.52) |
- | * Feeder Short-Circuit Protection (NEC 430.62) |
- | * Motor Disconnecting Means Sizing (NEC 430.110) |
- | * Motor Controller Ratings (NEC 430.83) |
- | |
- | [USE MOTOR NAMEPLATE (FLA)]: |
- | ---------------------------- |
- | * Motor Overload Protection Sizing ONLY (NEC 430.32 & 430.34) |
- | * Thermal Overload Relays / Heater Elements |
- | * Solid-State Electronic Overload Trip Settings |
- +-----------------------------------------------------------------------------+
Why Does the NEC Mandate Table FLC for Conductors and Switches?
Motor manufacturers build motors with varying efficiencies and power factors. A high-efficiency 10 HP motor might draw only 12 amperes at 460V, whereas a standard or older motor of the same horsepower might draw 14 amperes.
If the branch circuit conductors and disconnect switch were sized strictly for the 12-ampere nameplate motor, replacing that motor in the future with a standard 14-ampere motor would create an undersized, hazardous installation. Therefore, the NEC mandates using conservative, standardized Table FLC values for all upstream conductors, switches, and short-circuit protective devices. Conversely, overload protection is designed to protect the specific motor winding from overheating and burning out; hence, it must be matched to the exact nameplate FLA of that specific motor.
- Primary NEC Motor Tables
- Table 430.247: Full-Load Current in Amperes, Direct-Current Motors (DC)
- Table 430.248: Full-Load Current in Amperes, Single-Phase Alternating-Current Motors
- Table 430.249: Full-Load Current in Amperes, Two-Phase Alternating-Current Motors (4-Wire)
Table 430.250: Full-Load Current in Amperes, Three-Phase Alternating-Current Motors +-----------------------------------------------------------------------------+
- | EXCERPT: NEC TABLE 430.248 (SINGLE-PHASE AC MOTORS) |
- | |
- | Horsepower (HP) | 115 Volts | 200 Volts | 208 Volts | 230 Volts |
- | :---------------- | :------------ | :------------ | :---------- | :-------- |
- | 1/2 HP | 9.8 A | 5.6 A | 5.4 A | 4.9 A |
- | 3/4 HP | 13.8 A | 7.9 A | 7.6 A | 6.9 A |
- | 1 HP | 16.0 A | 9.2 A | 8.8 A | 8.0 A |
- | 1.5 HP | 20.0 A | 11.5 A | 11.0 A | 10.0 A |
- | 2 HP | 24.0 A | 13.8 A | 13.2 A | 12.0 A |
- | 3 HP | 34.0 A | 19.6 A | 18.7 A | 17.0 A |
- | 5 HP | 56.0 A | 32.2 A | 30.8 A | 28.0 A |
- | 7.5 HP | 80.0 A | 46.0 A | 44.0 A | 40.0 A |
- | 10 HP | 100.0 A | 57.5 A | 55.0 A | 50.0 A |
+-----------------------------------------------------------------------------+ +-----------------------------------------------------------------------------+
- | EXCERPT: NEC TABLE 430.250 (THREE-PHASE INDUCTION AC MOTORS) |
- | |
- | Horsepower (HP) | 208 Volts | 230 Volts | 460 Volts | 575 Volts |
- | :---------------- | :------------ | :------------ | :---------- | :-------- |
- | 3 HP | 10.6 A | 9.6 A | 4.8 A | 3.9 A |
- | 5 HP | 16.7 A | 15.2 A | 7.6 A | 6.1 A |
- | 7.5 HP | 24.2 A | 22.0 A | 11.0 A | 9.0 A |
- | 10 HP | 30.8 A | 28.0 A | 14.0 A | 11.0 A |
- | 15 HP | 46.2 A | 42.0 A | 21.0 A | 17.0 A |
- | 20 HP | 59.4 A | 54.0 A | 27.0 A | 22.0 A |
- | 25 HP | 74.8 A | 68.0 A | 34.0 A | 27.0 A |
- | 30 HP | 88.0 A | 80.0 A | 40.0 A | 32.0 A |
- | 40 HP | 114.0 A | 104.0 A | 52.0 A | 41.0 A |
- | 50 HP | 143.0 A | 130.0 A | 65.0 A | 52.0 A |
- | 75 HP | 211.0 A | 192.0 A | 96.0 A | 77.0 A |
- | 100 HP | 273.0 A | 248.0 A | 124.0 A | 99.0 A |
- +-----------------------------------------------------------------------------+
Note
Voltage Interpolation Rule for Table 430.250: When a motor operates at 200 volts nominal (rather than 208V or 230V), or at 115 volts 3-phase, the NEC instructs users to increase the 230V rating by 15% for 200V systems, or multiply the 230V rating by 2 for 115V systems.
2. Single-Motor Branch Circuit Conductor Sizing (NEC 430.22)
Under NEC 430.22 , branch-circuit conductors that supply a single motor used in a continuous-duty application must have an allowable ampacity of not less than 125% (1.25) of the motor full-load current rating as determined by NEC 430.6(A)(1).
Minimum Conductor Ampacity = I_Table_FLC * 1.25 +-----------------------------------------------------------------------------+
- | SINGLE-MOTOR BRANCH CIRCUIT SIZING FLOW |
- | |
- | [STEP 1] Identify Motor Phase, HP, and System Operating Voltage. |
- | [STEP 2] Look up Table FLC in Table 430.248 (1-Ph) or Table 430.250 (3-Ph).|
- | [STEP 3] Multiply Table FLC by 125% (1.25) for Continuous Duty. |
- | [STEP 4] Apply 110.14(C) Terminal Temperature Ratings to Table 310.16. |
- | [STEP 5] Apply Ambient Temperature & Bundling Deratings (if applicable). |
- | [STEP 6] Select Final AWG / kcmil Conductor Size. |
- +-----------------------------------------------------------------------------+
Why 125%?
The 125% factor accounts for the continuous heating effect of motor operating currents, transient overloads, and minor voltage fluctuations, preventing thermal fatigue on conductor insulation and terminal terminations over decades of service.
3. Continuous Duty vs. Intermittent Duty Ratings (NEC Table 430.22(E))
Not all motors operate continuously. Applications such as passenger elevators, overhead bridge cranes, drawbridges, freight hoists, and valve actuators operate for brief intervals or with long cooling cycles between operations. For these specialized non-continuous applications, NEC 430.22(E) mandates the use of duty-cycle multiplying percentages from NEC Table 430.22(E) rather than the standard 125% continuous multiplier.
Master Summary of NEC Table 430.22(E) Percentages
Classification of Service 5-Minute Rated Motor 15-Minute Rated Motor 30- & 60-Minute Rated Motor Continuous Rated Motor
- Short-Time Duty (Valves, raising/lowering rolls) 110% 120% 150% —
- Intermittent Duty (Pumps, elevators, toolheads) 85% 85% 90% 140%
- Periodic Duty (Rolls, ore-handling machines) 85% 90% 95% 140%
- Varying Duty (Shop tools, general hoists) 110% 120% 150% 200%
Warning
Default to Continuous Duty: Any motor application must be treated as continuous duty unless the nature of the apparatus it drives is inherently such that the motor cannot operate continuously under load. If an exam question does not explicitly state a short-time, intermittent, or periodic duty cycle, always apply the mandatory 125% continuous duty rule under NEC 430.22.
4. Terminal Temperature Ratings (NEC 110.14(C)) Applied to Motors
Selecting a conductor size requires coordinating the conductor ampacity from NEC Table 310.16 with the temperature ratings of the termination lugs under NEC 110.14(C) . +-----------------------------------------------------------------------------+
- | TERMINAL TEMPERATURE RULES (NEC 110.14(C)) |
- | |
- | [CIRCUITS RATED 100A OR LESS] (or conductors 14 AWG through 1 AWG): |
- | * Default rating is 60°C (Table 310.16 60°C column). |
- | * 75°C column permitted ONLY if all equipment terminals (breaker, starter,|
- | disconnect, motor junction box) are listed and marked for 75°C. |
- | |
- | [CIRCUITS RATED OVER 100A] (or conductors larger than 1 AWG): |
- | * Default rating is 75°C (Table 310.16 75°C column). |
- | |
- | [USING 90°C CONDUCTORS (e.g., THHN, XHHW-2)] |
- | * 90°C ampacity is used for derating (ambient temp & raceway fill). |
- | * Final adjusted ampacity CANNOT exceed the terminal rating (usually 75°C)|
- +-----------------------------------------------------------------------------+
Most modern magnetic starters, disconnect switches, and circuit breakers are listed with dual 60°C/75°C or straight 75°C terminals. Therefore, in commercial and industrial exam problems, the 75°C column of Table 310.16 is standard unless 60°C terminals are specifically identified.
5. Step-by-Step Worked Conductor Sizing Calculations
Let us work through three real-world calculation scenarios directly reflecting the Idaho Journeyman licensing exam format.
Calculation Problem 1: Single-Phase 230V Motor
Scenario: Calculate the minimum size 75°C copper THHN branch-circuit conductors required for a 5 HP, 230V, single-phase, continuous-duty squirrel-cage induction motor. The motor nameplate reads: FLA = 24.8 A, SF = 1.15, Temp Rise = 40°C . +-----------------------------------------------------------------------------+
- | PROBLEM 1 STEP-BY-STEP SOLUTION |
- | |
- | STEP 1: Select Current Value per NEC 430.6(A)(1). |
- | - Ignore nameplate FLA (24.8 A). |
- | - Go to Table 430.248: 5 HP at 230V = 28.0 A. |
- | |
- | STEP 2: Apply NEC 430.22 Continuous Duty Multiplier (125%). |
- | - Required Ampacity = 28.0 A x 1.25 = 35.0 A. |
- | |
- | STEP 3: Select Conductor from Table 310.16 (75°C Copper). |
- | - 12 AWG Cu (75°C) = 25 A (Too small) |
- | - 10 AWG Cu (75°C) = 35 A (Exactly matches 35.0 A) |
- | |
- | FINAL RESULT: Minimum conductor size is 10 AWG Copper. |
- +-----------------------------------------------------------------------------+
- Calculation Problem 2: Three-Phase 460V Motor
Scenario: Determine the minimum size 75°C copper THWN-2 branch-circuit conductors supplying a 15 HP, 460V, three-phase, continuous-duty motor with 75°C-rated terminal terminations. +-----------------------------------------------------------------------------+
- | PROBLEM 2 STEP-BY-STEP SOLUTION |
- | |
- | STEP 1: Table Lookup per NEC 430.6(A)(1). |
- | - Go to NEC Table 430.250: 15 HP at 460V = 21.0 A. |
- | |
- | STEP 2: Calculate Minimum Conductor Ampacity per NEC 430.22. |
- | - Ampacity = 21.0 A x 1.25 = 26.25 A. |
- | |
- | STEP 3: Select Conductor from Table 310.16 (75°C Copper). |
- | - 14 AWG Cu (75°C) = 20 A (Too small) |
- | - 12 AWG Cu (75°C) = 25 A (Too small, 25 A < 26.25 A) |
- | - 10 AWG Cu (75°C) = 35 A (Adequate, 35 A >= 26.25 A) |
- | |
- | FINAL RESULT: Minimum conductor size is 10 AWG Copper. |
- +-----------------------------------------------------------------------------+
- Calculation Problem 3: Three-Phase 208V Motor with Ambient Temperature Derating
Scenario: A 25 HP, 208V, 3-phase continuous-duty motor is installed in an industrial boiler room where the ambient temperature is 40°C (104°F). The circuit consists of three copper THHN (90°C) conductors in EMT connected to 75°C rated terminals. Determine the minimum wire size. +-----------------------------------------------------------------------------+
- | PROBLEM 3 STEP-BY-STEP SOLUTION |
- | |
- | STEP 1: Determine Table FLC (NEC Table 430.250). |
- | - 25 HP at 208V 3-Phase = 74.8 A. |
- | |
- | STEP 2: Calculate Minimum Base Conductor Ampacity (NEC 430.22). |
- | - Minimum Required Ampacity = 74.8 A x 1.25 = 93.5 A. |
- | |
- | STEP 3: Check Ambient Temperature Correction Factor (Table 310.15(B)(1)). |
- | - For 90°C insulation at 40°C ambient, Correction Factor = 0.91. |
- | |
- | STEP 4: Evaluate Conductor Candidates: |
- | - Try 3 AWG THHN (90°C Table 310.16 rating = 115 A): |
- | Derated Ampacity = 115 A x 0.91 = 104.65 A. |
- | Check 75°C Terminal Limit: 3 AWG (75°C) = 100 A. |
- | Since 100 A >= 93.5 A and derated 104.65 A >= 93.5 A, |
- | 3 AWG Cu satisfies all conditions! |
- | |
- | FINAL RESULT: Minimum conductor size is 3 AWG Copper. |
- +-----------------------------------------------------------------------------+
Tip
Quick Math Verification: On the exam, always verify that your selected conductor's 75°C ampacity is greater than or equal to 1.25 * Table FLC, AND that the conductor's derated 90°C ampacity is also greater than or equal to 1.25 * Table FLC.