Study guide
6.3 Lamellar Tearing
IIW International Welding Inspector — Standard IWI-S
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the IWI-S Qualification 1.2 Exam Structure, Routes & Scoring 1.3 How to Use This Guide
2 Inspector Role & Responsibilities
2.1 Inspector Duties Across the Weld Lifecycle 2.2 Reports, Traceability & Authority 2.3 IWI-S vs Basic and Comprehensive
3 Chapter 3: Arc Welding Processes I
3.1 Welding Technology Overview & Arc Fundamentals 3.2 MMA/SMAW Process & Flux-Coated Electrodes 3.3 MIG/MAG (GMAW) & Flux-Cored Arc Welding 3.4 TIG/GTAW Process
4 Chapter 4: Processes, Parameters & Consumables
4.1 SAW and Other Welding Processes 4.2 Cutting, Edge Preparation & Mechanisation 4.3 Heat Input, Arc Energy, Polarity & Parameters 4.4 ISO 4063 Process Numbers & Consumable Standards
5 Chapter 5: Metallurgy Foundations
5.1 Metals, Fe-C Alloys & Steel Classification 5.2 Structure of the Welded Joint & HAZ Zones 5.3 Carbon Equivalent, Hardenability & ISO/TR 15608 Groups
6 Chapter 6: Cracking Phenomena
6.1 Hydrogen Cold Cracking 6.2 Hot & Solidification Cracking 6.3 Lamellar Tearing 6.4 Fracture Types Related to Weld Defects
7 Chapter 7: Heat Treatment & Steel Families
7.1 Preheat, Interpass & PWHT 7.2 Carbon, Low-Alloy & Fine-Grain Steels 7.3 Creep-Resistant & Cryogenic Steels
8 Chapter 8: Stainless, Aluminium & Other Materials
8.1 Stainless & Heat-Resistant Steels 8.2 Aluminium & Aluminium Alloys 8.3 Nickel, Dissimilar Joints & Other Materials 8.4 Corrosion, Wear & Protective Layers
9 Chapter 9: Design & Welding Symbols
9.1 Strength of Materials Basics for Inspectors 9.2 Welded Joint Design & Preparation 9.3 ISO 2553 Welding Symbols 9.4 Fillet Throat Sizing & Structural Loading
10 Chapter 10: Fatigue, Distortion & Fabrication
10.1 Fatigue, Weld-Toe Effects & Fracture Mechanics Intro 10.2 Residual Stress & Distortion Control 10.3 Repair Welding, Plant Facilities & Health/Safety
11 Chapter 11: Weld Imperfections I
11.1 ISO 6520 Imperfection Classification 11.2 Cracks — Causes & Prevention 11.3 Porosity & Gas-Related Imperfections 11.4 Lack of Fusion & Lack of Penetration
12 Chapter 12: Weld Imperfections II
12.1 Undercut, Overlap & Shape Imperfections 12.2 Inclusions, Misalignment & Miscellaneous Defects 12.3 Evaluating Imperfections for Acceptance
13 Chapter 13: Surface NDT Methods
13.1 Visual Testing (ISO 17637) 13.2 Liquid Penetrant Testing (PT) 13.3 Magnetic Particle Testing (MT)
14 Chapter 14: Volumetric NDT & Destructive Tests
14.1 Radiographic Testing (RT) & Film Quality 14.2 Ultrasonic Testing (UT) 14.3 NDT Method Selection, IQI & ISO 9712 14.4 Destructive Testing of Welded Joints
15 Chapter 15: Codes, Acceptance & Qualification
15.1 ISO 5817 Quality Levels B/C/D 15.2 ISO 3834 Quality Requirements 15.3 WPS, WPQR & ISO 15614 15.4 Welder Qualification ISO 9606
16 Chapter 16: QA Documentation & Exam Strategy
16.1 Inspection Stages, ITPs & Hold Points 16.2 Materials Certificates, Traceability & In-Process Control 16.3 NCR, Reporting & QC Documents 16.4 Application of Standards & Practical Exam Strategy
6.3 Lamellar Tearing
Key Takeaways Explain This Topic AI
Lamellar tearing is a stepwise, terrace-like crack in the base metal driven by through-thickness tensile strain acting on planes of non-metallic inclusions or segregation
T-joints, corner joints, and other details that impose high through-thickness (short-transverse) strain are classic risk geometries
Prevention focuses on material selection (e.g. Z-quality / improved through-thickness ductility steels), joint design that reduces through-thickness strain, and buttering layers where specified
It is not the same mechanism as hydrogen HAZ cold cracking or weld-metal solidification cracking, though residual welding stress is still the driver
Inspectors should flag high-risk joint details, verify specified plate quality and orientation, and ensure NDT plans consider base-metal tearing near the joint
Last updated: July 2026
6.3 Lamellar Tearing
Quick Answer: Lamellar tearing is cracking in the base metal on planes parallel to the plate surface, caused by through-thickness tensile strain acting on bands of non-metallic inclusions or segregation. Classic risks are T-joints and corner joints welded to the plate face. Prevent with Z-quality steel , better design, and buttering when specified.
WT2.5 includes lamellar tearing because inspectors who only look for “weld cracks” will miss a base-metal failure mode that is driven by joint design and plate quality as much as by welding parameters.
What Lamellar Tearing Is
Rolled steel plate is not isotropic. Non-metallic inclusions (notably elongated sulphides and other stringers) and segregation bands tend to lie in planes parallel to the rolling direction and plate surface. When a large tensile strain acts through the thickness of the plate (the short-transverse direction), those weak planes can separate. The crack grows in a characteristic stepped or terrace-like path—hence “lamellar.”
Key distinctions:
Location is primarily parent plate , often just beneath the weld fusion zone where through-thickness stress is high
Path follows inclusion planes , not necessarily the weld centreline solidification structure
Initiation is tied to welding residual stress / shrinkage strain from attached welds, not to a liquid weld pool film (so it is not solidification cracking)
Hydrogen may aggravate cracking in steels generally, but the defining feature of lamellar tearing is through-thickness ductility deficiency of the plate product
Why T-Joints and Corner Joints Are Critical
Imagine a thick plate used as a flange or node. A stem plate is fillet- or butt-welded onto the face of the flange plate. As the weld cools, shrinkage pulls on the flange plate through its thickness . If the flange plate has poor short-transverse ductility, lamellar tears open under that pull.
High-risk geometries include:
- T-joints with full or heavy welds attaching a member normal to the plate surface
- Corner joints that load the plate through thickness
- Nodes and stiffener ends on thick plate with large weld volumes
- Repair welds that add large deposits onto already restrained details
Configurations where the loaded plate is thick , highly restrained , and of ordinary structural quality without improved through-thickness properties
Low-risk situations include thin plate, low restraint, small welds, and joints loaded mainly in the rolling plane rather than through thickness.
Material Factors
Through-thickness ductility depends on:
- Inclusion content and morphology (sulphur level, inclusion shape control)
- Segregation from casting and rolling practice
- Plate thickness and reduction ratio
- Steelmaking route (modern clean steels perform better than older high-inclusion plates)
Z-quality steels (improved through-thickness properties; often specified with a Z reduction-of-area requirement in the short-transverse direction under product standards such as those in the EN 10164 family of concepts) are the usual material solution when design demands high through-thickness strain capacity. The inspector’s job is not to recalculate Z-values on site, but to verify that the plate grade and certificates match the specification when Z-quality is required, and that plate is not substituted with ordinary stock.
Plate orientation also matters: the face that receives the weld must be the face intended by design. Mis-oriented plate or using plate edges incorrectly can change which direction sees through-thickness strain.
- Prevention Strategies
- 1. Material selection
Specify improved through-thickness ductility (Z-quality or equivalent project specification) for plates that will be loaded through thickness by welding
- Prefer clean, modern steels with controlled sulphur and inclusion shape where the design standard allows
- 2. Joint design
- Reduce weld size and volume to the structural minimum required
Redesign details so shrinkage does not pull heavily through the thickness of a susceptible plate (e.g. change attachment geometry, use soft toe details as designed by engineering)
Avoid stacking large welds on both sides of a thin ligament of susceptible plate without review
Sequence fabrication to avoid locking in maximum restraint before large welds are made, where the procedure allows
3. Buttering
Buttering deposits weld metal on the plate surface (often with a ductile consumable compatible with the procedure) before the final joint is completed. The buttering layer can:
- Place a more ductile, cleaner metal in the highest strain region
- Allow intermediate NDT of the buttered surface before the closing welds
- Sometimes be combined with stress-relief steps if the WPS/engineering specification requires them
Inspectors verify buttering is done with the qualified consumable and sequence , and that any hold points for NDT between buttering and final welding are observed.
4. Process and restraint control
Lower heat input is not a universal cure—and excessive restraint is always unhelpful. Follow the engineered WPS: some details use balanced welding, peening only if explicitly allowed, or PWHT for residual stress where the code and thickness require it. Improvised “more preheat” without design change does not convert a high-inclusion plate into Z-quality steel.
- Inspection Awareness
- Before welding
- Identify T, corner, and node details on drawings that impose through-thickness strain
- Confirm plate specification (including any Z-requirement) and material certificates
- Confirm buttering or special sequence notes on the WPS/ITP
- During / after welding
- Watch for surface-breaking steps or cracks in the base metal near the toe, not only cracks in weld metal
Ensure NDT methods and coverage include the base metal adjacent to the joint when the risk is lamellar tearing—not only the weld bead centreline
Ultrasonic testing is often important for subsurface terrace cracks; surface methods alone may miss internal steps
Treat any through-thickness crack indication in plate under a T-joint as a serious structural non-conformance requiring engineering disposition
Common confusion to avoid
- Observation More likely mechanism
- Centreline crack in bead just after welding Solidification (hot) cracking
- HAZ crack hours later on hardenable steel Hydrogen cold cracking
- Stepped crack in plate under a T-joint weld Lamellar tearing
- Toe crack after cyclic service Fatigue (Chapter 10 / fracture section)
- Fitness and Reporting
Lamellar tears reduce section integrity and can grow under residual or service stress. The IWI-S reports location, orientation, and joint detail; recommends the NDT extent defined by the quality plan; and stops progressive welding on sister joints if a systematic plate-quality or design problem is suspected. Repair may require gouging to sound metal, redesigned joint detail, or plate replacement—decisions for welding engineering, not ad-hoc fill.
Summary
Lamellar tearing is a base-metal, through-thickness cracking mode controlled by inclusions/segregation + through-thickness strain + residual welding stress . Master the T-joint story , Z-quality steel , design relief , and buttering , and you will answer WT2.5 lamellar items and spot high-risk details during document review and VT planning.