Study guide

14.4 Destructive Testing of Welded Joints

IIW International Welding Inspector — Standard IWI-S

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the IWI-S Qualification 1.2 Exam Structure, Routes & Scoring 1.3 How to Use This Guide

2 Inspector Role & Responsibilities

2.1 Inspector Duties Across the Weld Lifecycle 2.2 Reports, Traceability & Authority 2.3 IWI-S vs Basic and Comprehensive

3 Chapter 3: Arc Welding Processes I

3.1 Welding Technology Overview & Arc Fundamentals 3.2 MMA/SMAW Process & Flux-Coated Electrodes 3.3 MIG/MAG (GMAW) & Flux-Cored Arc Welding 3.4 TIG/GTAW Process

4 Chapter 4: Processes, Parameters & Consumables

4.1 SAW and Other Welding Processes 4.2 Cutting, Edge Preparation & Mechanisation 4.3 Heat Input, Arc Energy, Polarity & Parameters 4.4 ISO 4063 Process Numbers & Consumable Standards

5 Chapter 5: Metallurgy Foundations

5.1 Metals, Fe-C Alloys & Steel Classification 5.2 Structure of the Welded Joint & HAZ Zones 5.3 Carbon Equivalent, Hardenability & ISO/TR 15608 Groups

6 Chapter 6: Cracking Phenomena

6.1 Hydrogen Cold Cracking 6.2 Hot & Solidification Cracking 6.3 Lamellar Tearing 6.4 Fracture Types Related to Weld Defects

7 Chapter 7: Heat Treatment & Steel Families

7.1 Preheat, Interpass & PWHT 7.2 Carbon, Low-Alloy & Fine-Grain Steels 7.3 Creep-Resistant & Cryogenic Steels

8 Chapter 8: Stainless, Aluminium & Other Materials

8.1 Stainless & Heat-Resistant Steels 8.2 Aluminium & Aluminium Alloys 8.3 Nickel, Dissimilar Joints & Other Materials 8.4 Corrosion, Wear & Protective Layers

9 Chapter 9: Design & Welding Symbols

9.1 Strength of Materials Basics for Inspectors 9.2 Welded Joint Design & Preparation 9.3 ISO 2553 Welding Symbols 9.4 Fillet Throat Sizing & Structural Loading

10 Chapter 10: Fatigue, Distortion & Fabrication

10.1 Fatigue, Weld-Toe Effects & Fracture Mechanics Intro 10.2 Residual Stress & Distortion Control 10.3 Repair Welding, Plant Facilities & Health/Safety

11 Chapter 11: Weld Imperfections I

11.1 ISO 6520 Imperfection Classification 11.2 Cracks — Causes & Prevention 11.3 Porosity & Gas-Related Imperfections 11.4 Lack of Fusion & Lack of Penetration

12 Chapter 12: Weld Imperfections II

12.1 Undercut, Overlap & Shape Imperfections 12.2 Inclusions, Misalignment & Miscellaneous Defects 12.3 Evaluating Imperfections for Acceptance

13 Chapter 13: Surface NDT Methods

13.1 Visual Testing (ISO 17637) 13.2 Liquid Penetrant Testing (PT) 13.3 Magnetic Particle Testing (MT)

14 Chapter 14: Volumetric NDT & Destructive Tests

14.1 Radiographic Testing (RT) & Film Quality 14.2 Ultrasonic Testing (UT) 14.3 NDT Method Selection, IQI & ISO 9712 14.4 Destructive Testing of Welded Joints

15 Chapter 15: Codes, Acceptance & Qualification

15.1 ISO 5817 Quality Levels B/C/D 15.2 ISO 3834 Quality Requirements 15.3 WPS, WPQR & ISO 15614 15.4 Welder Qualification ISO 9606

16 Chapter 16: QA Documentation & Exam Strategy

16.1 Inspection Stages, ITPs & Hold Points 16.2 Materials Certificates, Traceability & In-Process Control 16.3 NCR, Reporting & QC Documents 16.4 Application of Standards & Practical Exam Strategy

14.4 Destructive Testing of Welded Joints

Key Takeaways Explain This Topic AI

Destructive tests (tensile, bend, impact/Charpy, hardness, macro/micro) destroy or section the specimen to prove mechanical and metallurgical properties of a procedure or welder qualification coupon

WPQR and welder qualification (e.g. ISO 15614 / ISO 9606 families) rely on specified DT (and NDT) sequences — inspectors witness, verify identity, and review lab results against acceptance criteria

Tensile tests check strength; bend tests check ductility/soundness; Charpy impact checks toughness at temperature; hardness maps HAZ/weld peaks; macro/micro reveal fusion, HAZ structure, and defects on a cut face

IWI-S duties include witnessing tests as required by the ITP and taking decisions on quality documents such as laboratory certificates — not inventing results without lab data

Lab certificates must be traceable to the coupon ID, standard method, temperature, and acceptance values; incomplete certificates are incomplete quality documents

Last updated: July 2026

14.4 Destructive Testing of Welded Joints

Quick Answer: Destructive testing (DT) proves properties by breaking, bending, impacting, indenting, or sectioning welded specimens. It underpins WPQR (e.g. ISO 15614 route) and welder qualification (e.g. ISO 9606) together with required NDT. Common tests: tensile , bend , Charpy impact , hardness , macro (± micro). IWI-S witnesses tests when required, verifies coupon identity/traceability , and reviews lab certificates as quality documents — without fabricating mechanical values.

NDT asks “is this production weld free of rejectable discontinuities?” DT asks “does this qualified procedure/welder coupon meet mechanical and structural requirements?” Both appear in WI2.1 and in practical inspection competence.

Why Destroy Good Welds?

A qualification coupon is sacrificed so production can proceed with confidence . Properties that matter:

  • Strength — will the joint carry design load (tensile, sometimes all-weld-metal tensile)
  • Ductility / soundness — can it bend without cracking from LOF, inclusions, or brittle zones
  • Toughness — resistance to brittle fracture at design temperature (Charpy V-notch energy or lateral expansion)
  • Hardness — HAZ peaks linked to hydrogen cracking risk or wear applications; PWHT effectiveness
  • Macrostructure — fusion, penetration, HAZ extent, multipass sequence, defects on the polished section

Production welds are usually not all destructively tested; sampling and NDT protect production. Qualification is the place where DT is intensive.

  • Core Test Types for Welding Inspectors
  • Tensile tests

Transverse tensile specimens pull the weld across the joint. Acceptance typically requires failure load/strength meeting parent metal or specified minimums, with failure location notes (weld, HAZ, parent). All-weld-metal tensile (when required) characterises deposited metal. Inspector checks: specimen machining from correct location, orientation, standard method on the certificate, and numeric results vs WPQR acceptance.

Bend tests

Face, root, and side bends (as required by thickness and standard) bend the specimen over a former of specified diameter. They expose lack of fusion, inclusions, and brittle regions as cracks on the tension surface. Partial small openings may be limited by acceptance criteria; open defects usually fail. Bends are highly visual for witnessing — you can see soundness failures without a densitometer.

Impact tests (Charpy V-notch)

A notched bar is broken by a pendulum at a specified temperature . Energy absorbed (joules) and sometimes lateral expansion or fracture appearance are recorded. Toughness qualification is temperature-critical: a pass at −20 °C does not automatically prove −40 °C service without the correct test temperature. Notch location (weld metal, FL, HAZ offsets) is defined by the procedure qualification standard. Inspector traps: wrong temperature, wrong notch location, or averaging tricks not allowed by the standard.

Hardness testing

Vickers or other methods map hardness across weld, HAZ, and parent on a macro section or production survey. Limits may cap maximum HAZ hardness (hydrogen cracking control) or require minimum hardness for wear. After PWHT, hardness can show whether heat treatment met the intent. Equipment calibration and indent placement matter; random single indents without a traverse may be noncompliant with the WPQR standard’s figure.

Macro and micro examination

Macro (low magnification, etched section) shows fusion line, penetration, number of passes, undercut, pores, cracks, and HAZ width. Acceptance may allow only imperfections within procedure standard limits. Micro (higher magnification) examines microstructure (e.g. grain size, phases in stainless, potential brittle constituents) when the standard or client requires it. Macro is frequent in WPQR packages; micro is more selective.

  • Test Primary question answered
  • Transverse tensile Strength of joint path
  • Bend (face/root/side) Ductility + gross soundness
  • Charpy impact Toughness at temperature
  • Hardness traverse Peak hardness / PWHT effect
  • Macro etch Fusion, profile, visible defects on section
  • Micro Detailed microstructure when required
  • Use in WPQR and Welder Tests

Procedure qualification (WPQR / PQR) — e.g. under ISO 15614 series (know the concept even if you memorise the project’s exact part): a test piece is welded with recorded parameters; NDT and DT are performed per the standard’s table for material group, thickness, and joint type. Passing results support a WPS range of validity (thickness, diameter, positions, etc.).

Welder / welding operator qualification — e.g. ISO 9606 / ISO 14732 : the person (or operator) demonstrates skill on a coupon. Tests often include visual, bend or fracture, and sometimes radiography/UT depending on the standard and product. Range of qualification (process, material group, position, thickness) follows the standard’s rules.

Inspector responsibilities in both streams:

Before welding the coupon — verify WPS draft/parameters, material certificates, consumable batch, joint preparation, position, essential variables understanding

  • During welding — witness as ITP requires; record actual parameters for the WPQR
  • After welding — ensure coupon ID, heat number, welder ID stamping; prevent mix-ups
  • NDT of coupon — before cutting specimens if required
  • DT laboratory — correct specimen extraction plan; chain of custody
  • Review certificates — accept/reject package; raise NCR if failed; control retest rules
  • Witnessing Tests as IWI-S Duty

Witnessing is not passive tourism. Effective witness includes:

  • Confirming which standard and acceptance table apply
  • Confirming specimen identity matches the welded coupon (stamp transfer, cutting sketch)
  • Observing critical steps defined as hold points (e.g. bend execution, impact temperature verification)
  • Checking lab equipment calibration status where accessible/required
  • Recording time, place, results, deviations in the inspection report
  • Stopping the process if identity is lost or the wrong specimen is about to be tested

You may not personally operate the tensile machine if company practice assigns that to the lab technician — but you own the verification trail when the ITP names welding inspection witness.

Laboratory Certificates — Critical Review

A lab certificate is a quality document . Incomplete certificates fail review even if someone says “it passed verbally.”

Minimum review points:

  • Laboratory identity and accreditation statements as contract requires
  • Customer, project, and unique specimen/coupon ID
  • Welding process, base material, consumable references linking to WPQR
  • Test standard method (e.g. which tensile/impact standard)
  • Temperature for impact; notch location
  • Numeric results with units and acceptance criteria used
  • Date, technician/authorisation signatures
  • Any deviations, retests, or broken grips notes

Trap: accepting a tensile certificate that omits specimen ID or shows parent metal strength without confirming failure location rules required by the qualification standard. Trap: Charpy results at ambient used to claim low-temperature qualification.

DT vs NDT — Keep the Distinction Sharp

  • NDT DT
  • Production weld remains in service Usually yes No (coupon destroyed)
  • Finds discontinuities in place Yes Section may reveal defects but coupon is sacrificed
  • Measures mechanical properties No (generally) Yes
  • Typical use Production acceptance Qualification / production test coupons

Both feed quality documents on which IWI-S may decide. Neither replaces process control.

Link to Later Chapters

Chapter 15 develops ISO 15614 / ISO 9606 acceptance logic and ISO 5817 quality levels in more depth. Chapter 16 places DT/NDT witness points inside ITPs and NCR loops. For now, master the test menu , witness discipline , and certificate literacy .

  • Exam Focus
  • Name tensile, bend, Charpy, hardness, macro/micro and what each proves
  • WPQR vs welder test purpose of DT
  • Witness and traceability duties
  • Lab certificate completeness as a quality-document decision
  • DT does not replace NDT on production welds required by code