Study guide
9.3 Operator Applied Mathematics: Water & Wastewater Calculations
Illinois Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Illinois Environmental Laws, Administrative Rules & Operator Certification
1.1 Illinois EPA Regulatory Framework & Permitting 1.2 Wastewater Operator Certification: Classes 1-4, K, R & Collection System 1.3 Drinking Water Operator Certification: Classes A-D
2 Chapter 2: Water Sources, Coagulation, Flocculation & Clarification
2.1 Water Sources, Characteristics & Intake Management 2.2 Coagulation Chemistry & Rapid Mixing 2.3 Flocculation, Sedimentation & Clarifier Operation
3 Chapter 3: Filtration Technologies & Advanced Drinking Water Treatment
3.1 Granular Media Filtration Operations 3.2 Membrane Filtration & Ion Exchange Softening 3.3 Lime-Soda Ash Softening, Iron & Manganese Removal 3.4 Fluoridation, Corrosion Control & Disinfection Byproducts
4 Chapter 4: Disinfection Science & Chemical Feed Systems
4.1 Chlorine Chemistry, Forms & Breakpoint Chlorination 4.2 Contact Time (CT) Calculations & Alternative Disinfectants 4.3 Chemical Feed Equipment, Calibration & Feed Rate Math
5 Chapter 5: Wastewater Preliminary, Primary, Lagoon & Fixed-Film Treatment
5.1 Preliminary Treatment: Screening, Comminution & Grit Removal 5.2 Primary Clarification & Sedimentation 5.3 Waste Stabilization Ponds & Facultative Lagoons 5.4 Trickling Filters & Rotating Biological Contactors 5.5 Imhoff Tanks, Septic Tank Systems & Intermittent Sand Filters
6 Chapter 6: Activated Sludge Treatment & Process Control
6.1 Activated Sludge Variations & Flow Schemes 6.2 Key Operational Parameters: MLSS, F/M, MCRT & SVI 6.3 Return Activated Sludge (RAS) & Waste Activated Sludge (WAS) Control 6.4 Operational Troubleshooting, Bulking & Foaming
7 Chapter 7: Nutrient Removal, Effluent Polishing & Solids Handling
7.1 Biological & Chemical Nutrient Removal 7.2 Effluent Disinfection, Dechlorination & Polishing 7.3 Aerobic & Anaerobic Sludge Digestion 7.4 Sludge Thickening, Dewatering & Biosolids Regulations 7.5 Sludge Drying Beds & Air-Drying Systems
8 Chapter 8: Water Distribution, Wastewater Collection & Pumping Systems
8.1 Water Distribution Piping, Storage & Backflow Prevention 8.2 Wastewater Collection Systems, Inflow & Infiltration 8.3 Lift Stations, Wet Wells & Hydraulics 8.4 Centrifugal & Positive Displacement Pumps 8.5 Flow Measurement, Weirs, Flumes & Meters 8.6 Motors, Electrical Systems, Instrumentation & SCADA
9 Chapter 9: Laboratory Analysis, Applied Calculations, Safety & Plant Administration
9.1 Drinking Water Laboratory Testing & Compliance Sampling 9.2 Wastewater Laboratory Testing & Quality Assurance 9.3 Operator Applied Mathematics: Water & Wastewater Calculations 9.4 Plant Safety, Confined Space Entry & Chlorine Handling 9.5 Plant Management, Preventive Maintenance & Recordkeeping
9.3 Operator Applied Mathematics: Water & Wastewater Calculations
Key Takeaways Explain This Topic AI
The Universal Pounds Formula (lbs/day = Flow in MGD × Concentration in mg/L × 8.34 lbs/gal) governs chemical dosing, biological mass loadings, and solids wasting throughout water and wastewater operations.
Hydraulic Detention Time relates tank volume to volumetric flow rate; clarifier performance is controlled by Surface Overflow Rate (SOR, gpd/sq ft), Weir Overflow Rate (WOR, gpd/linear ft), and Solids Loading Rate (SLR, lbs/sq ft·day).
Filtration loading rate (gpm/sq ft) and backwash rise rate (in/min = gpm/sq ft × 1.604) ensure media cleaning without loss of filter sand or anthracite.
Activated sludge operational control relies on the Food-to-Microorganism ratio (F/M), Mean Cell Residence Time (MCRT / sludge age), Sludge Volume Index (SVI), and daily WAS pumping rate equations.
Pumping power requirements progress from theoretical hydraulic power (Water Horsepower, WHP = gpm × TDH / 3,960) to shaft power (Brake Horsepower, BHP) and electrical input power (Motor Horsepower, MHP / wire-to-water efficiency).
Last updated: September 2026
9.3 Operator Applied Mathematics: Water & Wastewater Calculations
Mathematical proficiency is indispensable for certified water and wastewater operators. Calculations govern everyday operational decisions, including chemical dosing adjustments, clarifier loading rates, activated sludge wasting schedules, and pump sizing. Mastering unit conversions, formulas, and dimensional analysis ensures plant compliance and prevents costly operational errors.
The Universal "Pounds Formula"
The Pounds Formula is the single most widely used equation in environmental engineering. It establishes the quantitative relationship between volumetric liquid flow, concentration in parts per million (milligrams per liter), and total mass loading.
The Core Equation Pounds per day (lbs/day) = Flow (MGD) × Concentration (mg/L) × 8.34 lbs/gal \text{Pounds per day (lbs/day)} = \text{Flow (MGD)} \times \text{Concentration (mg/L)} \times 8.34\text{ lbs/gal} Pounds per day (lbs/day) = Flow (MGD) × Concentration (mg/L) × 8.34 lbs/gal
Derivation & Unit Conversion :
1 gallon of water = 8.34 lbs 1\text{ gallon of water} = 8.34\text{ lbs} 1 gallon of water = 8.34 lbs
1 mg/L = 1 part per million (ppm) = 1 lb analyte 1 , 000 , 000 lbs water 1\text{ mg/L} = 1\text{ part per million (ppm)} = \frac{1\text{ lb analyte}}{1,000,000\text{ lbs water}} 1 mg/L = 1 part per million (ppm) = 1 , 000 , 000 lbs water 1 lb analyte
Flow in MGD = Gallons 1 , 000 , 000 days \text{Flow in MGD} = \frac{\text{Gallons}}{1,000,000\text{ days}} Flow in MGD = 1 , 000 , 000 days Gallons
Multiplying: Million Gallons day × 8.34 lbs gallon × lbs analyte 1 , 000 , 000 lbs water × 1 , 000 , 000 = lbs/day \frac{\text{Million Gallons}}{\text{day}} \times \frac{8.34\text{ lbs}}{\text{gallon}} \times \frac{\text{lbs analyte}}{1,000,000\text{ lbs water}} \times 1,000,000 = \text{lbs/day} day Million Gallons × gallon 8.34 lbs × 1 , 000 , 000 lbs water lbs analyte × 1 , 000 , 000 = lbs/day .
Core Formula Variations
Mass in a Tank or Basin : Pounds in Tank (lbs) = Tank Volume (MG) × Concentration (mg/L) × 8.34 lbs/gal \text{Pounds in Tank (lbs)} = \text{Tank Volume (MG)} \times \text{Concentration (mg/L)} \times 8.34\text{ lbs/gal} Pounds in Tank (lbs) = Tank Volume (MG) × Concentration (mg/L) × 8.34 lbs/gal
Solving for Required Chemical Dosage : Dosage (mg/L) = Chemical Feed Rate (lbs/day) Flow (MGD) × 8.34 lbs/gal \text{Dosage (mg/L)} = \frac{\text{Chemical Feed Rate (lbs/day)}}{\text{Flow (MGD)} \times 8.34\text{ lbs/gal}} Dosage (mg/L) = Flow (MGD) × 8.34 lbs/gal Chemical Feed Rate (lbs/day)
Accounting for Chemical Purity & Solution Strength : Commercial Chemical Required (lbs/day) = Pure Active Ingredient Required (lbs/day) Decimal Purity \text{Commercial Chemical Required (lbs/day)} = \frac{\text{Pure Active Ingredient Required (lbs/day)}}{\text{Decimal Purity}} Commercial Chemical Required (lbs/day) = Decimal Purity Pure Active Ingredient Required (lbs/day) For liquid solutions with a specific gravity ( S G SG SG ) and percentage strength by weight ( % solution \%\text{ solution} % solution ): Chemical Feed (gpd) = Active Chemical Required (lbs/day) 8.34 × S G × ( % solution 100 ) \text{Chemical Feed (gpd)} = \frac{\text{Active Chemical Required (lbs/day)}}{8.34 \times SG \times \left(\frac{\% \text{ solution}}{100}\right)} Chemical Feed (gpd) = 8.34 × SG × ( 100 % solution ) Active Chemical Required (lbs/day)
Worked Example 1: Disinfection Chemical Dosing
Problem : A water plant treats 4.50 MGD 4.50\text{ MGD} 4.50 MGD with an intended chlorine dosage of 2.80 mg/L 2.80\text{ mg/L} 2.80 mg/L . The plant uses commercial liquid sodium hypochlorite ( N a O C l NaOCl N a OCl ) with an active available chlorine strength of 12.5 % 12.5\% 12.5% and a specific gravity of 1.20 1.20 1.20 . Calculate the required commercial bleach feed rate in gallons per day (gpd).
Step 1: Calculate active pure chlorine demand in lbs/day: lbs/day = 4.50 MGD × 2.80 mg/L × 8.34 lbs/gal = 105.084 lbs/day \text{lbs/day} = 4.50\text{ MGD} \times 2.80\text{ mg/L} \times 8.34\text{ lbs/gal} = 105.084\text{ lbs/day} lbs/day = 4.50 MGD × 2.80 mg/L × 8.34 lbs/gal = 105.084 lbs/day
Step 2: Calculate weight of 1 gallon of commercial hypochlorite solution: Weight per gallon = 8.34 lbs/gal × 1.20 (SG) = 10.008 lbs/gal \text{Weight per gallon} = 8.34\text{ lbs/gal} \times 1.20\text{ (SG)} = 10.008\text{ lbs/gal} Weight per gallon = 8.34 lbs/gal × 1.20 (SG) = 10.008 lbs/gal
Step 3: Calculate active chlorine pounds per gallon of solution: Active chlorine/gal = 10.008 lbs/gal × 0.125 (purity) = 1.251 lbs active Cl 2 /gal \text{Active chlorine/gal} = 10.008\text{ lbs/gal} \times 0.125\text{ (purity)} = 1.251\text{ lbs active Cl}_2\text{/gal} Active chlorine/gal = 10.008 lbs/gal × 0.125 (purity) = 1.251 lbs active Cl 2 /gal
Step 4: Calculate daily chemical feed in gallons: Feed Rate = 105.084 lbs Cl 2 /day 1.251 lbs Cl 2 /gal = 84.00 gpd \text{Feed Rate} = \frac{105.084\text{ lbs Cl}_2\text{/day}}{1.251\text{ lbs Cl}_2\text{/gal}} = 84.00\text{ gpd} Feed Rate = 1.251 lbs Cl 2 /gal 105.084 lbs Cl 2 /day = 84.00 gpd
Tank Geometry & Volumetric Capacity
Accurate volume calculations are the prerequisite for detention time, tank inventory, and chemical batching.
- Fundamental Geometric Formulas Tank Volumetric Calculations
- Rectangular Basins Circular Basins / Clarifiers
- ┌─────────────────────────┐ ┌─────────────────────────────────┐
- │ Vol (cu ft) = L × W × D │ │ Vol (cu ft) = 0.785 × D² × Depth│
- └─────────────────────────┘ └─────────────────────────────────┘
- │ │
- ▼ ▼
- ┌─────────────────────────┐ ┌─────────────────────────────────┐
- │ Gallons = cu ft × 7.48 │ │ Gallons = cu ft × 7.48 │
- └─────────────────────────┘ └─────────────────────────────────┘
- │ │
- ▼ ▼
- ┌─────────────────────────┐ ┌─────────────────────────────────┐
- │ MG = Gallons / 1,000,000│ │ MG = Gallons / 1,000,000 │
- └─────────────────────────┘ └─────────────────────────────────┘
Rectangular Basins : Volume (cu ft) = Length (ft) × Width (ft) × Depth (ft) \text{Volume (cu ft)} = \text{Length (ft)} \times \text{Width (ft)} \times \text{Depth (ft)} Volume (cu ft) = Length (ft) × Width (ft) × Depth (ft) Volume (gallons) = Volume (cu ft) × 7.48 gal/cu ft \text{Volume (gallons)} = \text{Volume (cu ft)} \times 7.48\text{ gal/cu ft} Volume (gallons) = Volume (cu ft) × 7.48 gal/cu ft
Circular Clarifiers & Cylindrical Wet Wells : Surface Area (sq ft) = π 4 × D 2 = 0.7854 × D 2 \text{Surface Area (sq ft)} = \frac{\pi}{4} \times D^2 = 0.7854 \times D^2 Surface Area (sq ft) = 4 π × D 2 = 0.7854 × D 2 Volume (cu ft) = 0.7854 × [ Diameter (ft) ] 2 × Side Water Depth (ft) \text{Volume (cu ft)} = 0.7854 \times [\text{Diameter (ft)}]^2 \times \text{Side Water Depth (ft)} Volume (cu ft) = 0.7854 × [ Diameter (ft) ] 2 × Side Water Depth (ft) Volume (gallons) = 0.7854 × D 2 × Depth × 7.48 gal/cu ft \text{Volume (gallons)} = 0.7854 \times D^2 \times \text{Depth} \times 7.48\text{ gal/cu ft} Volume (gallons) = 0.7854 × D 2 × Depth × 7.48 gal/cu ft
Hydraulic Detention Time (DT & HRT)
Detention time represents the theoretical average duration a parcel of liquid resides inside a treatment basin.
Detention Time Formulas Detention Time (hours) = Basin Volume (gallons) × 24 hours/day Flow Rate (gallons per day, gpd) \text{Detention Time (hours)} = \frac{\text{Basin Volume (gallons)} \times 24\text{ hours/day}}{\text{Flow Rate (gallons per day, gpd)}} Detention Time (hours) = Flow Rate (gallons per day, gpd) Basin Volume (gallons) × 24 hours/day Detention Time (minutes) = Basin Volume (gallons) × 1 , 440 minutes/day Flow Rate (gpd) \text{Detention Time (minutes)} = \frac{\text{Basin Volume (gallons)} \times 1,440\text{ minutes/day}}{\text{Flow Rate (gpd)}} Detention Time (minutes) = Flow Rate (gpd) Basin Volume (gallons) × 1 , 440 minutes/day
Worked Example 2: Flocculation Basin Detention Time
Problem : A surface water plant treats 3.60 MGD 3.60\text{ MGD} 3.60 MGD ( 3 , 600 , 000 gpd 3,600,000\text{ gpd} 3 , 600 , 000 gpd ). The flocculation basin measures 70.0 ft long 70.0\text{ ft long} 70.0 ft long , 25.0 ft wide 25.0\text{ ft wide} 25.0 ft wide , and has a water depth of 12.0 ft 12.0\text{ ft} 12.0 ft . Calculate the hydraulic detention time in minutes.
Step 1: Calculate basin volume in cubic feet: Volume = 70.0 ft × 25.0 ft × 12.0 ft = 21 , 000 cu ft \text{Volume} = 70.0\text{ ft} \times 25.0\text{ ft} \times 12.0\text{ ft} = 21,000\text{ cu ft} Volume = 70.0 ft × 25.0 ft × 12.0 ft = 21 , 000 cu ft
Step 2: Convert cubic feet to gallons: Gallons = 21 , 000 cu ft × 7.48 gal/cu ft = 157 , 080 gallons \text{Gallons} = 21,000\text{ cu ft} \times 7.48\text{ gal/cu ft} = 157,080\text{ gallons} Gallons = 21 , 000 cu ft × 7.48 gal/cu ft = 157 , 080 gallons
Step 3: Calculate detention time in minutes: DT (min) = 157 , 080 gal × 1 , 440 min/day 3 , 600 , 000 gpd = 226 , 195 , 200 3 , 600 , 000 = 62.83 minutes \text{DT (min)} = \frac{157,080\text{ gal} \times 1,440\text{ min/day}}{3,600,000\text{ gpd}} = \frac{226,195,200}{3,600,000} = 62.83\text{ minutes} DT (min) = 3 , 600 , 000 gpd 157 , 080 gal × 1 , 440 min/day = 3 , 600 , 000 226 , 195 , 200 = 62.83 minutes
Clarifier Hydraulic & Solids Loading Rates
Clarifiers separate settleable flocs and biological solids from treated water. Exceeding hydraulic or solids loading rates induces floc carryover and solids loss.
Loading Rate Formulas
Surface Overflow Rate (SOR) : Flow applied per unit of clarifier horizontal surface area: SOR (gpd/sq ft) = Influent Flow (gpd) Surface Area (sq ft) = Flow (gpd) 0.7854 × D 2 \text{SOR (gpd/sq ft)} = \frac{\text{Influent Flow (gpd)}}{\text{Surface Area (sq ft)}} = \frac{\text{Flow (gpd)}}{0.7854 \times D^2} SOR (gpd/sq ft) = Surface Area (sq ft) Influent Flow (gpd) = 0.7854 × D 2 Flow (gpd) Standard Range : Primary clarifiers: 800 – 1 , 200 gpd/sq ft 800\text{--}1,200\text{ gpd/sq ft} 800 – 1 , 200 gpd/sq ft ; Secondary clarifiers: 400 – 800 gpd/sq ft 400\text{--}800\text{ gpd/sq ft} 400 – 800 gpd/sq ft .
Weir Overflow Rate (WOR) : Flow escaping over each linear foot of effluent weir: WOR (gpd/linear ft) = Influent Flow (gpd) Total Active Weir Length (ft) \text{WOR (gpd/linear ft)} = \frac{\text{Influent Flow (gpd)}}{\text{Total Active Weir Length (ft)}} WOR (gpd/linear ft) = Total Active Weir Length (ft) Influent Flow (gpd) For a circular clarifier with a continuous peripheral weir: Weir Length = π × D = 3.1416 × Diameter (ft) \text{Weir Length} = \pi \times D = 3.1416 \times \text{Diameter (ft)} Weir Length = π × D = 3.1416 × Diameter (ft) . Standard Range : 10 , 000 – 20 , 000 gpd/linear ft 10,000\text{--}20,000\text{ gpd/linear ft} 10 , 000 – 20 , 000 gpd/linear ft .
Solids Loading Rate (SLR) : Total daily solids mass applied per square foot of secondary clarifier area (incorporating return activated sludge flow): SLR (lbs/sq ft ⋅ day) = [ Influent Flow (MGD) + RAS Flow (MGD) ] × MLSS (mg/L) × 8.34 lbs/gal Clarifier Surface Area (sq ft) \text{SLR (lbs/sq ft}\cdot\text{day)} = \frac{[\text{Influent Flow (MGD)} + \text{RAS Flow (MGD)}] \times \text{MLSS (mg/L)} \times 8.34\text{ lbs/gal}}{\text{Clarifier Surface Area (sq ft)}} SLR (lbs/sq ft ⋅ day) = Clarifier Surface Area (sq ft) [ Influent Flow (MGD) + RAS Flow (MGD) ] × MLSS (mg/L) × 8.34 lbs/gal Standard Range : Peak design: 24 – 35 lbs/sq ft ⋅ day 24\text{--}35\text{ lbs/sq ft}\cdot\text{day} 24 – 35 lbs/sq ft ⋅ day ; Average: 15 – 20 lbs/sq ft ⋅ day 15\text{--}20\text{ lbs/sq ft}\cdot\text{day} 15 – 20 lbs/sq ft ⋅ day .
Filtration & Backwash Mathematics
Granular media filters require exact flow control during production and clean fluidization during backwash.
Loading, Rise Rate & Bed Expansion
Filtration Loading Rate : Hydraulic flux per unit area: Filtration Rate (gpm/sq ft) = Filter Inflow (gpm) Filter Surface Area (sq ft) \text{Filtration Rate (gpm/sq ft)} = \frac{\text{Filter Inflow (gpm)}}{\text{Filter Surface Area (sq ft)}} Filtration Rate (gpm/sq ft) = Filter Surface Area (sq ft) Filter Inflow (gpm) Standard Range : Rapid sand: 2 gpm/sq ft 2\text{ gpm/sq ft} 2 gpm/sq ft ; Dual media (anthracite/sand): 3 – 5 gpm/sq ft 3\text{--}5\text{ gpm/sq ft} 3 – 5 gpm/sq ft ; High-rate: 6 – 8 gpm/sq ft 6\text{--}8\text{ gpm/sq ft} 6 – 8 gpm/sq ft .
Backwash Rise Rate : The upward vertical velocity of backwash water through the bed: Rise Rate (inches/minute) = Backwash Rate (gpm/sq ft) × 1.604 \text{Rise Rate (inches/minute)} = \text{Backwash Rate (gpm/sq ft)} \times 1.604 Rise Rate (inches/minute) = Backwash Rate (gpm/sq ft) × 1.604
Constant Derivation : 1 gpm sq ft = 1 gal/min 1 sq ft × 1 cu ft 7.48 gal = 0.1336898 ft min × 12 inches 1 ft = 1.60427 in/min \frac{1\text{ gpm}}{\text{sq ft}} = \frac{1\text{ gal/min}}{1\text{ sq ft}} \times \frac{1\text{ cu ft}}{7.48\text{ gal}} = \frac{0.1336898\text{ ft}}{\text{min}} \times \frac{12\text{ inches}}{1\text{ ft}} = 1.60427\text{ in/min} sq ft 1 gpm = 1 sq ft 1 gal/min × 7.48 gal 1 cu ft = min 0.1336898 ft × 1 ft 12 inches = 1.60427 in/min .
Percent Bed Expansion : Quantifies media bed fluidization during backwash: % Bed Expansion = Expanded Bed Depth (inches) − Settled Bed Depth (inches) Settled Bed Depth (inches) × 100 % \%\text{ Bed Expansion} = \frac{\text{Expanded Bed Depth (inches)} - \text{Settled Bed Depth (inches)}}{\text{Settled Bed Depth (inches)}} \times 100\% % Bed Expansion = Settled Bed Depth (inches) Expanded Bed Depth (inches) − Settled Bed Depth (inches) × 100% Standard Operational Target : 20 % to 30 % 20\%\text{ to } 30\% 20% to 30% expansion ensures inter-particle scouring without washing media into troughs.
Worked Example 3: Backwash Hydraulics
Problem : A dual-media filter measuring 15.0 ft × 20.0 ft 15.0\text{ ft} \times 20.0\text{ ft} 15.0 ft × 20.0 ft is backwashed at a rate of 4 , 800 gpm 4,800\text{ gpm} 4 , 800 gpm . Calculate: (a) backwash loading rate in gpm/sq ft \text{gpm/sq ft} gpm/sq ft , and (b) backwash rise rate in inches per minute.
Step 1: Calculate filter surface area: Area = 15.0 ft × 20.0 ft = 300 sq ft \text{Area} = 15.0\text{ ft} \times 20.0\text{ ft} = 300\text{ sq ft} Area = 15.0 ft × 20.0 ft = 300 sq ft
Step 2: Calculate backwash loading rate: Rate = 4 , 800 gpm 300 sq ft = 16.0 gpm/sq ft \text{Rate} = \frac{4,800\text{ gpm}}{300\text{ sq ft}} = 16.0\text{ gpm/sq ft} Rate = 300 sq ft 4 , 800 gpm = 16.0 gpm/sq ft
Step 3: Calculate backwash rise rate: Rise Rate = 16.0 gpm/sq ft × 1.604 = 25.66 inches/minute \text{Rise Rate} = 16.0\text{ gpm/sq ft} \times 1.604 = 25.66\text{ inches/minute} Rise Rate = 16.0 gpm/sq ft × 1.604 = 25.66 inches/minute
Activated Sludge Process Mathematics
Process control of suspended growth activated sludge systems relies on biological balance equations.
Food-to-Microorganism Ratio ( F / M F/M F / M )
F / M F/M F / M characterizes the daily organic food supply relative to the active microbial population in the aeration basin: F / M = lbs BOD applied/day lbs MLVSS in aeration = Flow (MGD) × Influent BOD (mg/L) × 8.34 Aeration Basin Volume (MG) × MLVSS (mg/L) × 8.34 F/M = \frac{\text{lbs BOD applied/day}}{\text{lbs MLVSS in aeration}} = \frac{\text{Flow (MGD)} \times \text{Influent BOD (mg/L)} \times 8.34}{\text{Aeration Basin Volume (MG)} \times \text{MLVSS (mg/L)} \times 8.34} F / M = lbs MLVSS in aeration lbs BOD applied/day = Aeration Basin Volume (MG) × MLVSS (mg/L) × 8.34 Flow (MGD) × Influent BOD (mg/L) × 8.34
Standard Range for Conventional Activated Sludge : 0.20 to 0.50 lbs BOD/lb MLVSS ⋅ day 0.20\text{ to } 0.50\text{ lbs BOD/lb MLVSS}\cdot\text{day} 0.20 to 0.50 lbs BOD/lb MLVSS ⋅ day . Extended aeration: 0.05 to 0.15 0.05\text{ to } 0.15 0.05 to 0.15 .
Mean Cell Residence Time ( M C R T MCRT MCRT / Sludge Age)
M C R T MCRT MCRT represents the average duration (in days) active biological solids remain in the treatment system: M C R T (days) = Total System MLSS (lbs) WAS TSS (lbs/day) + Effluent TSS (lbs/day) MCRT\text{ (days)} = \frac{\text{Total System MLSS (lbs)}}{\text{WAS TSS (lbs/day)} + \text{Effluent TSS (lbs/day)}} MCRT (days) = WAS TSS (lbs/day) + Effluent TSS (lbs/day) Total System MLSS (lbs) M C R T = [ V aeration ( MG ) + V clarifier ( MG ) ] × MLSS (mg/L) × 8.34 [ Q WAS ( MGD ) × WAS TSS ( mg/L ) × 8.34 ] + [ Q eff ( MGD ) × Eff TSS ( mg/L ) × 8.34 ] MCRT = \frac{[V_{\text{aeration}} (\text{MG}) + V_{\text{clarifier}} (\text{MG})] \times \text{MLSS (mg/L)} \times 8.34}{[Q_{\text{WAS}} (\text{MGD}) \times \text{WAS}_{\text{TSS}} (\text{mg/L}) \times 8.34] + [Q_{\text{eff}} (\text{MGD}) \times \text{Eff}_{\text{TSS}} (\text{mg/L}) \times 8.34]} MCRT = [ Q WAS ( MGD ) × WAS TSS ( mg/L ) × 8.34 ] + [ Q eff ( MGD ) × Eff TSS ( mg/L ) × 8.34 ] [ V aeration ( MG ) + V clarifier ( MG )] × MLSS (mg/L) × 8.34
Standard Range : Conventional activated sludge: 5 – 15 days 5\text{--}15\text{ days} 5 – 15 days ; Nitrification systems: 10 – 25 days 10\text{--}25\text{ days} 10 – 25 days .
Sludge Volume Index ( S V I SVI S V I )
S V I SVI S V I defines the settling volume (in milliliters) occupied by 1.0 gram 1.0\text{ gram} 1.0 gram of mixed liquor suspended solids after 30 minutes of quiescent settling in a 1-liter settleometer or graduated cylinder: S V I (mL/g) = Settled Sludge Volume after 30 min (mL/L) × 1 , 000 mg/g MLSS Concentration (mg/L) SVI\text{ (mL/g)} = \frac{\text{Settled Sludge Volume after 30 min (mL/L)} \times 1,000\text{ mg/g}}{\text{MLSS Concentration (mg/L)}} S V I (mL/g) = MLSS Concentration (mg/L) Settled Sludge Volume after 30 min (mL/L) × 1 , 000 mg/g
SVI Range (mL/g) Sludge Characteristics & Settling Behavior Potential Operational Issue
< 80 < 80 < 80 Dense, rapid settling, compact pin-point floc Fast settling; cloudy/turbid effluent with fine sheared pin floc
80 – 150 80\text{--}150 80 – 150 Ideal settling, clear supernatant, uniform floc blanket Optimal operation (normal target)
> 150 – 200 > 150\text{--}200 > 150 – 200 Slow settling, bulky sludge, high blanket level Filamentous bulking, organic overloading, nutrient deficiency
Waste Activated Sludge ( W A S WAS W A S ) Pumping Rate
To maintain target M C R T MCRT MCRT or MLSS inventory, operators must calculate daily volume of WAS to pump: Target WAS Pumping Rate (gpd) = Target WAS Wasting (lbs/day) WAS Concentration (mg/L) × 8.34 × 10 − 6 \text{Target WAS Pumping Rate (gpd)} = \frac{\text{Target WAS Wasting (lbs/day)}}{\text{WAS Concentration (mg/L)} \times 8.34 \times 10^{-6}} Target WAS Pumping Rate (gpd) = WAS Concentration (mg/L) × 8.34 × 1 0 − 6 Target WAS Wasting (lbs/day)
Pump Power, Hydraulics & Electrical Efficiency
Moving water through mains and treatment units requires calculating head loss and mechanical power.
- Horsepower Hierarchy & Wire-to-Water Efficiency Horsepower Progression
- Electrical Power Input Shaft Mechanical Power Useful Hydraulic Work
- ┌──────────────────────┐ ┌──────────────────────┐ ┌──────────────────────┐
- │ Motor Horsepower │ ─ Motor Eff ─► │ Brake Horsepower │ ─ Pump Eff ──► │ Water Horsepower │
- │ (MHP) │ (ηm) │ (BHP) │ (ηp) │ (WHP) │
- └──────────────────────┘ └──────────────────────┘ └──────────────────────┘
- ▲ │
- └──────────────────────── Wire-to-Water Efficiency (ηw-w) ──────────────────────┘
Water Horsepower ( W H P WHP W H P ) : The theoretical power imparted directly to the water: W H P = Flow Rate (gpm) × Total Dynamic Head (TDH, ft) 3 , 960 WHP = \frac{\text{Flow Rate (gpm)} \times \text{Total Dynamic Head (TDH, ft)}}{3,960} W H P = 3 , 960 Flow Rate (gpm) × Total Dynamic Head (TDH, ft)
Constant Derivation : 1 HP = 33 , 000 ft-lbs/min 1\text{ HP} = 33,000\text{ ft-lbs/min} 1 HP = 33 , 000 ft-lbs/min . Since water weighs 8.34 lbs/gal 8.34\text{ lbs/gal} 8.34 lbs/gal : 33 , 000 ft-lbs/min 8.34 lbs/gal = 3 , 956.83 ≈ 3 , 960 \frac{33,000\text{ ft-lbs/min}}{8.34\text{ lbs/gal}} = 3,956.83 \approx 3,960 8.34 lbs/gal 33 , 000 ft-lbs/min = 3 , 956.83 ≈ 3 , 960 .
Brake Horsepower ( B H P BHP B H P ) : The mechanical horsepower required at the pump shaft, accounting for internal impeller and bearing friction losses: B H P = W H P Pump Efficiency ( η p ) BHP = \frac{WHP}{\text{Pump Efficiency } (\eta_p)} B H P = Pump Efficiency ( η p ) W H P
Motor Horsepower ( M H P MHP M H P ) : The total electrical horsepower demanded by the electric drive motor, accounting for electrical resistance and magnetic eddy-current losses: M H P = B H P Motor Efficiency ( η m ) = W H P η p × η m MHP = \frac{BHP}{\text{Motor Efficiency } (\eta_m)} = \frac{WHP}{\eta_p \times \eta_m} M H P = Motor Efficiency ( η m ) B H P = η p × η m W H P
Wire-to-Water Efficiency ( η w − w \eta_{w-w} η w − w ) : The overall efficiency of the combined pumping unit: η w − w = η p × η m = W H P M H P × 100 % \eta_{w-w} = \eta_p \times \eta_m = \frac{WHP}{MHP} \times 100\% η w − w = η p × η m = M H P W H P × 100%
Worked Example 4: Pumping Efficiency & Power Costs
Problem : A high-service pump delivers 2 , 200 gpm 2,200\text{ gpm} 2 , 200 gpm against a Total Dynamic Head of 180 ft 180\text{ ft} 180 ft . The pump efficiency is 80 % 80\% 80% (0.80) and the electric motor efficiency is 90 % 90\% 90% (0.90). Calculate: (a) Water Horsepower, (b) Brake Horsepower, (c) Motor Horsepower, and (d) Wire-to-Water Efficiency.
Step 1: Calculate Water Horsepower: W H P = 2 , 200 gpm × 180 ft 3 , 960 = 396 , 000 3 , 960 = 100.0 WHP WHP = \frac{2,200\text{ gpm} \times 180\text{ ft}}{3,960} = \frac{396,000}{3,960} = 100.0\text{ WHP} W H P = 3 , 960 2 , 200 gpm × 180 ft = 3 , 960 396 , 000 = 100.0 WHP
Step 2: Calculate Brake Horsepower: B H P = 100.0 WHP 0.80 = 125.0 BHP BHP = \frac{100.0\text{ WHP}}{0.80} = 125.0\text{ BHP} B H P = 0.80 100.0 WHP = 125.0 BHP
Step 3: Calculate Motor Horsepower: M H P = 125.0 BHP 0.90 = 138.89 MHP MHP = \frac{125.0\text{ BHP}}{0.90} = 138.89\text{ MHP} M H P = 0.90 125.0 BHP = 138.89 MHP
Step 4: Calculate Wire-to-Water Efficiency: η w − w = 0.80 × 0.90 × 100 % = 72.0 % \eta_{w-w} = 0.80 \times 0.90 \times 100\% = 72.0\% η w − w = 0.80 × 0.90 × 100% = 72.0%