Study guide
4.1 NEMA Phase Numbering, Dual-Ring Barriers, and Overlaps
IMSA Traffic Signal Field Technician Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Worksite Safety and Maintenance of Traffic
1.1 Electrical Safety, PPE, and Lockout/Tagout at Signal Cabinets 1.2 Maintenance of Traffic and Work-Site Protection
2 Chapter 2: Traffic Signal Standards and Equipment Operation
2.1 MUTCD Part 4 Standards for Signal Displays and Operation 2.2 NEMA TS 1 vs NEMA TS 2 Standards 2.3 Load Switches, Flashers, and Bus Interface Units 2.4 Model 170 / 2070 and Advanced Transportation Controller (ATC) Cabinets
3 Chapter 3: Malfunction Management and Cabinet Safety Monitoring
3.1 Malfunction Management Units (MMU) and Conflict Monitors 3.2 MMU Programming, Bench Testing, and Annual Certification
4 Chapter 4: Signal Phasing and Timing
4.1 NEMA Phase Numbering, Dual-Ring Barriers, and Overlaps 4.2 Actuated Interval Timing and Volume-Density Features 4.3 Yellow Change and Red Clearance Intervals 4.4 Pedestrian Timing, ADA Requirements, and Accessible Pedestrian Signals
5 Chapter 5: Coordination and System Timing
5.1 Coordinated Signal Concepts and Terminology 5.2 Time-Space Diagrams and Bandwidth Optimization 5.3 Offset Calculation Methods and Coordination Systems 5.4 Actuated Coordinated Systems and Force-Off Modes 5.5 Time-of-Day (TOD) vs Traffic-Responsive Coordination
6 Chapter 6: Vehicle and Pedestrian Detection
6.1 Inductive Loop Detection Fundamentals and Configurations 6.2 Loop Installation, Lead-In, Splices, and Electrical Testing 6.3 Non-Intrusive Detection: Video, Radar, and Magnetometer Systems 6.4 Detector Amplifier Setup and Detection Troubleshooting
7 Chapter 7: Equipment Repair, Replacement, and Programming
7.1 Controller Programming and Database Management 7.2 Signal Heads, LED Modules, and Field Wiring Replacement 7.3 Uninterruptible Power Supply and Battery Backup Systems 7.4 Grounding, Bonding, and Surge Protection
8 Chapter 8: Pre-emption and Priority Systems
8.1 Emergency Vehicle Pre-emption (EVP) 8.2 Railroad Pre-emption and Advance Warning 8.3 Transit Signal Priority (TSP) and Priority vs Pre-emption
9 Chapter 9: Test Equipment and Troubleshooting
9.1 Test Equipment for the Signal Field Technician 9.2 Systematic Troubleshooting Methodology 9.3 Diagnosing Dark Signals, Flashing Operation, and Cabinet Faults 9.4 Communications and Interconnect Fault Diagnosis
10 Chapter 10: System Communications and Networking
10.1 Closed Loop Architecture and Interconnect Media 10.2 Basic Networking, IP Addressing, and NTCIP 10.3 Central Software, Telemetry, and System Monitoring
11 Chapter 11: Field Infrastructure and Plan Interpretation
11.1 Reading Signal Plans, Wiring Diagrams, and Cable Schedules 11.2 Conduit, Pull Boxes, and Underground Infrastructure 11.3 Signal Poles, Mast Arms, Foundations, and Head Wiring
12 Chapter 12: Preventive Maintenance, Documentation, and Liability
12.1 Preventive Maintenance Programs and Inspection Routines 12.2 Maintenance Documentation, Logs, and Asset Management 12.3 Tort Liability, Notice, and Defensible Maintenance Records
4.1 NEMA Phase Numbering, Dual-Ring Barriers, and Overlaps
Key Takeaways Explain This Topic AI
In the standard NEMA eight-phase dual-ring arrangement, Ring 1 contains phases 1, 2, 3, and 4 and Ring 2 contains phases 5, 6, 7, and 8, with a barrier between phases 2/6 and 3/7.
Odd-numbered phases are left turns and each odd phase is the left turn opposing the through movement numbered one higher — phase 1 opposes phase 2, phase 5 opposes phase 6.
A barrier is a compatibility line that both rings must cross at the same instant, which is why one slow phase on one ring delays the other ring's progression to the next street.
Compatible concurrency before the barrier is any of phases 1 or 2 with any of phases 5 or 6; after the barrier it is any of 3 or 4 with any of 7 or 8.
An overlap displays green whenever any of its assigned parent phases is green, plus an optional trailing green, and it consumes its own monitored channel and load switch position.
Last updated: August 2026
4.1 NEMA Phase Numbering, Dual-Ring Barriers, and Overlaps
Everything a Level II field technician does in a cabinet is expressed in phase numbers. The controller's timing screens, the monitor's permissive program card, the load bay position labels, the field terminal strip, and the signal plan's phasing diagram all use the same numbering, and a technician who cannot translate a phase number into a physical movement cannot safely program, wire, or troubleshoot the intersection.
The Dual-Ring Structure
A ring is a sequence of phases that must be served one at a time. A NEMA eight-phase controller uses two rings that run in parallel: BARRIER BARRIER
- | |
- Ring 1: 1 | 2 || 3 | 4 || (back to 1)
- Ring 2: 5 | 6 || 7 | 8 || (back to 5)
- | |
- Main Street Side Street
A barrier (also called a compatibility line) is the point where both rings must cross at the same instant . Its purpose is to guarantee that no movement from the main street is ever green at the same time as a movement from the side street. This is why a single long side-street left turn on Ring 2 holds Ring 1 at the barrier: Ring 1 cannot advance to phase 3 until Ring 2 has finished phase 7 and 8 and reached the same barrier.
Numbering Conventions
Two rules generate the entire standard layout:
Even-numbered phases are through movements; odd-numbered phases are left turns.
Each odd phase is the left turn that opposes the through movement numbered one higher. Phase 1 opposes phase 2. Phase 3 opposes phase 4. Phase 5 opposes phase 6. Phase 7 opposes phase 8.
By convention, phase 2 is assigned to a major-street through movement , and it is normally the coordinated phase along with phase 6. Because phase 1 opposes phase 2, phase 1 and phase 6 belong to the same approach (a left turn and the through beside it) and may therefore be green together. The same reasoning makes phase 5 and phase 2 a same-approach pair.
Which Phases May Run Together
- Pair Compatible? Why
- 1 + 5 Yes Opposing protected left turns; no crossing conflict
- 2 + 6 Yes Opposing through movements
- 1 + 6 Yes Left turn and through on the same approach (lag left)
- 2 + 5 Yes Left turn and through on the same approach (lead left)
- 2 + 4 No Crosses the barrier — main street through vs. side street through
- 1 + 4 No Crosses the barrier
- 3 + 7 Yes Opposing side-street left turns
- 4 + 8 Yes Opposing side-street through movements
This table is exactly what a technician transfers onto the monitor's permissive program card. Every "Yes" gets a jumper; every "No" is left open.
Lead, Lag, and Phase Sequence
Within the pre-barrier group, the controller can serve the left turns in four sequences:
Lead-lead (1 and 5 first, then 2 and 6) — the classic dual protected-left arrangement.
Lag-lag (2 and 6 first, then 1 and 5).
Lead-lag (1 leads, 5 lags, producing a 1+6 then 2+6 then 2+5 progression) — used to widen a progression band in one direction.
Lag-lead — the mirror image.
Lead-lag sequences are a coordination tool, but they carry the yellow trap hazard when a permissive left turn faces a circular green that terminates while the opposing through stays green. A driver waiting in the intersection sees yellow, assumes opposing traffic also has yellow, and turns into a still-green through movement. The standard remedy is a flashing yellow arrow head, which controls the permissive left independently of the adjacent through indication.
Pedestrian Phases
Pedestrian movements are numbered to match the vehicle phase they run with: 2P, 4P, 6P, 8P on a standard eight-phase layout. In a 16-channel monitor, pedestrian channels typically occupy channels 9 through 12 , paired to their parent vehicle channels.
The operational rule a technician must internalize: a pedestrian phase can force its parent vehicle phase to run longer than the vehicle timing alone would require. If phase 4's split is shorter than the pedestrian walk plus clearance time for the 4P crossing, serving a pedestrian call breaks the split, which in a coordinated pattern drops the controller into transition.
Overlaps
An overlap is a signal display that is green whenever any of its assigned parent phases is green. Overlaps are lettered A, B, C, D (and beyond on modern controllers) and each one consumes a load switch position and a monitored channel — commonly channels 13 through 16 on a 16-channel unit.
The Classic Right-Turn Overlap
A northbound right-turn arrow can safely be green whenever the northbound through (its own street) is green and whenever the opposing left turn that clears the conflicting path is green. Assigning that right-turn overlap to parent phases 2 and 3 (or the equivalent pair at the specific intersection) gives the right turn a protected green through two separate phases instead of one.
Programming Elements
- Parameter Function
- Included (parent) phases The phases whose green drives the overlap green
Modifier / omit phases Phases that suppress the overlap even when a parent is green — used when a pedestrian phase conflicts with the turn
- Trailing green Extra green after the last parent phase terminates, allowing the turn to clear
- Overlap yellow and red clearance The overlap's own change intervals, programmed separately from its parents
- Type Standard, minus green, pedestrian protected, or flashing yellow arrow overlap
- Why Overlaps Break Things
Overlaps cause a disproportionate share of monitor trips because they introduce a green indication that is not directly tied to a single phase. Two common failures:
The overlap is programmed with a parent phase that conflicts with a pedestrian movement, so the right-turn arrow stays green across a crossing pedestrian. The monitor sees overlap green concurrent with Walk on a non-permissive pair and trips.
The overlap's own yellow and red clearance are left at zero because the programmer assumed the parent phase's clearance would carry, producing a clearance failure the first time the overlap terminates independently.
Both are programming errors that appear at the intersection as intermittent, hard-to-reproduce flash events — which is exactly why a technician confirms overlap programming against the plan's phasing diagram rather than against the previous cabinet's database.