Study guide
4.4 Pedestrian Timing, ADA Requirements, and Accessible Pedestrian Signals
IMSA Traffic Signal Field Technician Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Worksite Safety and Maintenance of Traffic
1.1 Electrical Safety, PPE, and Lockout/Tagout at Signal Cabinets 1.2 Maintenance of Traffic and Work-Site Protection
2 Chapter 2: Traffic Signal Standards and Equipment Operation
2.1 MUTCD Part 4 Standards for Signal Displays and Operation 2.2 NEMA TS 1 vs NEMA TS 2 Standards 2.3 Load Switches, Flashers, and Bus Interface Units 2.4 Model 170 / 2070 and Advanced Transportation Controller (ATC) Cabinets
3 Chapter 3: Malfunction Management and Cabinet Safety Monitoring
3.1 Malfunction Management Units (MMU) and Conflict Monitors 3.2 MMU Programming, Bench Testing, and Annual Certification
4 Chapter 4: Signal Phasing and Timing
4.1 NEMA Phase Numbering, Dual-Ring Barriers, and Overlaps 4.2 Actuated Interval Timing and Volume-Density Features 4.3 Yellow Change and Red Clearance Intervals 4.4 Pedestrian Timing, ADA Requirements, and Accessible Pedestrian Signals
5 Chapter 5: Coordination and System Timing
5.1 Coordinated Signal Concepts and Terminology 5.2 Time-Space Diagrams and Bandwidth Optimization 5.3 Offset Calculation Methods and Coordination Systems 5.4 Actuated Coordinated Systems and Force-Off Modes 5.5 Time-of-Day (TOD) vs Traffic-Responsive Coordination
6 Chapter 6: Vehicle and Pedestrian Detection
6.1 Inductive Loop Detection Fundamentals and Configurations 6.2 Loop Installation, Lead-In, Splices, and Electrical Testing 6.3 Non-Intrusive Detection: Video, Radar, and Magnetometer Systems 6.4 Detector Amplifier Setup and Detection Troubleshooting
7 Chapter 7: Equipment Repair, Replacement, and Programming
7.1 Controller Programming and Database Management 7.2 Signal Heads, LED Modules, and Field Wiring Replacement 7.3 Uninterruptible Power Supply and Battery Backup Systems 7.4 Grounding, Bonding, and Surge Protection
8 Chapter 8: Pre-emption and Priority Systems
8.1 Emergency Vehicle Pre-emption (EVP) 8.2 Railroad Pre-emption and Advance Warning 8.3 Transit Signal Priority (TSP) and Priority vs Pre-emption
9 Chapter 9: Test Equipment and Troubleshooting
9.1 Test Equipment for the Signal Field Technician 9.2 Systematic Troubleshooting Methodology 9.3 Diagnosing Dark Signals, Flashing Operation, and Cabinet Faults 9.4 Communications and Interconnect Fault Diagnosis
10 Chapter 10: System Communications and Networking
10.1 Closed Loop Architecture and Interconnect Media 10.2 Basic Networking, IP Addressing, and NTCIP 10.3 Central Software, Telemetry, and System Monitoring
11 Chapter 11: Field Infrastructure and Plan Interpretation
11.1 Reading Signal Plans, Wiring Diagrams, and Cable Schedules 11.2 Conduit, Pull Boxes, and Underground Infrastructure 11.3 Signal Poles, Mast Arms, Foundations, and Head Wiring
12 Chapter 12: Preventive Maintenance, Documentation, and Liability
12.1 Preventive Maintenance Programs and Inspection Routines 12.2 Maintenance Documentation, Logs, and Asset Management 12.3 Tort Liability, Notice, and Defensible Maintenance Records
4.4 Pedestrian Timing, ADA Requirements, and Accessible Pedestrian Signals
Key Takeaways Explain This Topic AI
MUTCD guidance sets the walk interval at least 7 seconds, with an option for intervals as short as 4 seconds where pedestrian volumes and characteristics do not require 7.
Pedestrian clearance time is calculated using a walking speed of 3.5 feet per second from the curb or edge of pavement to the far side of the traveled way or to a median of adequate width.
A buffer interval of at least 2 seconds shall always be provided and displayed after the pedestrian change interval, and the countdown display is optional only for pedestrian change intervals of 7 seconds or less.
Accessible pedestrian signal push button locator tones shall have a duration of 0.15 seconds or less and repeat at 1-second intervals whenever the audible walk indication is not active.
Vibrotactile arrows shall be located on the push button, have high visual contrast, and be aligned parallel to the direction of travel on the associated crosswalk.
Last updated: August 2026
4.4 Pedestrian Timing, ADA Requirements, and Accessible Pedestrian Signals
A vehicle timing complaint produces a phone call. A pedestrian timing deficiency produces a Department of Justice inquiry. Pedestrian signal requirements sit at the intersection of the MUTCD, the Americans with Disabilities Act, and the U.S. Access Board's public right-of-way accessibility guidelines, and a Level II field technician is the person who physically verifies that the intersection meets them.
The Three Pedestrian Intervals
A pedestrian phase is built from three parts, displayed in a fixed order.
Interval Display Rule
Walk interval Steady WALKING PERSON Should be at least 7 seconds ; may be as short as 4 seconds where pedestrian volumes and characteristics do not require 7. It is the time to enter the crosswalk, not to cross it.
Pedestrian change interval Flashing UPRAISED HAND, with countdown Time for a pedestrian who left the curb at the end of Walk to complete the crossing.
Buffer interval Steady UPRAISED HAND Shall always be provided and displayed , minimum 2 seconds , before conflicting movements are released.
The calculated pedestrian clearance time must be satisfied by the pedestrian change interval, optionally with help from the buffer interval. The buffer may be used to help satisfy the calculated clearance time, or it may begin after that time has ended — but it is never omitted.
Walking Speed
Pedestrian clearance time is calculated at 3.5 feet per second from the curb or edge of pavement to the far side of the traveled way, or to a median of sufficient width for pedestrians to wait. Where pedestrians who walk slower than 3.5 ft/s, or who use wheelchairs, routinely use the crosswalk, a slower walking speed should be considered .
The Pedestrian Timing Check
The MUTCD adds a separate check that catches crossings where a short walk interval and a fast clearance calculation combine badly: the total of the walk interval and the pedestrian clearance time should be sufficient to allow a pedestrian who left the pedestrian detector (or, where none is provided, a point 6 feet from the curb) to travel at 3.0 feet per second to the far side of the traveled way. The check uses a slower speed and a longer distance than the clearance calculation, and it frequently forces a longer walk interval than 7 seconds at wide crossings.
Countdown Displays
The countdown display shows the number of seconds remaining in the pedestrian change interval and reaches zero at the end of that interval — not at the end of the buffer. The countdown display is optional for pedestrian change intervals of 7 seconds or less and required otherwise. A countdown that runs into the buffer interval, restarts, or displays during Walk is mis-set and must be corrected.
Leading Pedestrian Intervals
A leading pedestrian interval (LPI) starts the Walk indication several seconds before the parallel vehicle green so pedestrians establish presence in the crosswalk before turning vehicles move. Where an LPI is used, the walk interval should still be at least 7 seconds. An LPI has a field consequence a technician must anticipate: the right-turn overlap or permissive right turn must be held red during the LPI, which usually means adding a modifier or omit condition to an overlap.
Accessible Pedestrian Signals
MUTCD Chapter 4K governs accessible pedestrian signals (APS) and detectors in the 11th Edition. An APS conveys the walk interval non-visually — by audible indication and by vibration — so that a pedestrian who is blind or has low vision receives the same information a sighted pedestrian receives from the WALKING PERSON symbol.
Required Elements
Element Requirement
Push button locator tone Duration 0.15 seconds or less , repeating at 1-second intervals whenever the audible walk indication is not active — including during the pedestrian change interval and while the signal rests in walk
Locator tone audibility Should be audible 6 to 12 feet from the push button, or to the building line, whichever is less
Locator tone response Shall be intensity responsive to ambient sound
Locator tone in flash Shall be deactivated when the signal is operating in flashing mode, except where a pedestrian actuation brings the signal from flash or dark into steady operation
Vibrotactile arrow Located on the button , high visual contrast (light on dark or dark on light), aligned parallel to the direction of travel on the associated crosswalk
- Audible walk indication A percussive tone (rapid tick) or a speech walk message
- Time-of-day operation Under steady operation, APS shall not be limited by time of day or day of week
- Extended Push Button Press
Holding the button for an extended period (commonly more than one second) may activate additional features: increased crossing time , audible beaconing that alternates sound across the crosswalk to guide a pedestrian along the crossing line, or a speech push button information message naming the street being crossed and the direction of travel.
Where the Push Button Goes
Push button placement is as much a compliance item as timing. The button must be reachable from an accessible route and positioned so that a pedestrian facing the button is facing the crossing it serves. Where two push buttons are mounted on the same pole, they must be separated enough that a pedestrian cannot confuse which crossing each serves — the standard practice is separate poles or a minimum separation with distinct arrow orientations. Where the pedestrian clearance time is sufficient only to reach a median, an additional accessible detector must be provided on the median .
Field Checks a Technician Performs
Confirm the arrow points at the crossing it serves. A vibrotactile arrow rotated 90 degrees on its mount sends a pedestrian who is blind into the wrong crosswalk. This is the most common APS defect found in the field and it is created by careless reinstallation after a knockdown.
Verify the locator tone repeats at roughly one second and is short. A continuous tone, a tone that stops entirely, or a tone that keeps sounding while the intersection is in flash are all defects.
Confirm the tone responds to ambient sound. Run the intersection during a traffic surge and confirm the volume rises, then confirm it falls in quiet conditions. A locator tone pinned at maximum volume generates noise complaints that lead agencies to disable APS entirely.
Press the button and confirm both feedback channels. The button must give a visual, audible, and tactile confirmation that the call was registered.
Time the intervals. Stopwatch the Walk, the flashing hand with countdown, and the buffer for every crossing, and compare against the approved timing sheet.
Check the countdown zero point. The display must reach zero at the end of the pedestrian change interval.
Never disable an APS to silence a complaint. Adjusting volume within the ambient-response range is maintenance; turning the unit off is removing an accessibility feature.