Study guide
2.4 Model 170 / 2070 and Advanced Transportation Controller (ATC) Cabinets
IMSA Traffic Signal Field Technician Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Worksite Safety and Maintenance of Traffic
1.1 Electrical Safety, PPE, and Lockout/Tagout at Signal Cabinets 1.2 Maintenance of Traffic and Work-Site Protection
2 Chapter 2: Traffic Signal Standards and Equipment Operation
2.1 MUTCD Part 4 Standards for Signal Displays and Operation 2.2 NEMA TS 1 vs NEMA TS 2 Standards 2.3 Load Switches, Flashers, and Bus Interface Units 2.4 Model 170 / 2070 and Advanced Transportation Controller (ATC) Cabinets
3 Chapter 3: Malfunction Management and Cabinet Safety Monitoring
3.1 Malfunction Management Units (MMU) and Conflict Monitors 3.2 MMU Programming, Bench Testing, and Annual Certification
4 Chapter 4: Signal Phasing and Timing
4.1 NEMA Phase Numbering, Dual-Ring Barriers, and Overlaps 4.2 Actuated Interval Timing and Volume-Density Features 4.3 Yellow Change and Red Clearance Intervals 4.4 Pedestrian Timing, ADA Requirements, and Accessible Pedestrian Signals
5 Chapter 5: Coordination and System Timing
5.1 Coordinated Signal Concepts and Terminology 5.2 Time-Space Diagrams and Bandwidth Optimization 5.3 Offset Calculation Methods and Coordination Systems 5.4 Actuated Coordinated Systems and Force-Off Modes 5.5 Time-of-Day (TOD) vs Traffic-Responsive Coordination
6 Chapter 6: Vehicle and Pedestrian Detection
6.1 Inductive Loop Detection Fundamentals and Configurations 6.2 Loop Installation, Lead-In, Splices, and Electrical Testing 6.3 Non-Intrusive Detection: Video, Radar, and Magnetometer Systems 6.4 Detector Amplifier Setup and Detection Troubleshooting
7 Chapter 7: Equipment Repair, Replacement, and Programming
7.1 Controller Programming and Database Management 7.2 Signal Heads, LED Modules, and Field Wiring Replacement 7.3 Uninterruptible Power Supply and Battery Backup Systems 7.4 Grounding, Bonding, and Surge Protection
8 Chapter 8: Pre-emption and Priority Systems
8.1 Emergency Vehicle Pre-emption (EVP) 8.2 Railroad Pre-emption and Advance Warning 8.3 Transit Signal Priority (TSP) and Priority vs Pre-emption
9 Chapter 9: Test Equipment and Troubleshooting
9.1 Test Equipment for the Signal Field Technician 9.2 Systematic Troubleshooting Methodology 9.3 Diagnosing Dark Signals, Flashing Operation, and Cabinet Faults 9.4 Communications and Interconnect Fault Diagnosis
10 Chapter 10: System Communications and Networking
10.1 Closed Loop Architecture and Interconnect Media 10.2 Basic Networking, IP Addressing, and NTCIP 10.3 Central Software, Telemetry, and System Monitoring
11 Chapter 11: Field Infrastructure and Plan Interpretation
11.1 Reading Signal Plans, Wiring Diagrams, and Cable Schedules 11.2 Conduit, Pull Boxes, and Underground Infrastructure 11.3 Signal Poles, Mast Arms, Foundations, and Head Wiring
12 Chapter 12: Preventive Maintenance, Documentation, and Liability
12.1 Preventive Maintenance Programs and Inspection Routines 12.2 Maintenance Documentation, Logs, and Asset Management 12.3 Tort Liability, Notice, and Defensible Maintenance Records
2.4 Model 170 / 2070 and Advanced Transportation Controller (ATC) Cabinets
Key Takeaways Explain This Topic AI
The Caltrans Model 332 cabinet utilizes a standardized 19-inch EIA rack-mount architecture incorporating Model 200 load switches, Model 204 flashers, Model 242 DC isolators, and Model 430 Flash Transfer Relays.
Model 170 logic controllers rely on 8-bit Motorola 6800/68HC11 microprocessors and removable EPROM/PROM modules (Model 412/420), whereas Model 2070 controllers utilize 32-bit processors with VME/VME64 backplanes running OS-9 or Linux operating systems.
Standardized cabinet connectors in 332 architecture include the C1 connector (main controller I/O to input/output files), C2 connector (serial communications), and C11 connector (conflict monitor interface).
Advanced Transportation Controller (ATC) Cabinets (ATC 5201 / ATC Cabinet v2.0) transition field load switching from 120 VAC to low-voltage 48 VDC architecture, dramatically improving technician safety and reducing cabinet thermal dissipation.
ATC cabinets implement High-Density Switch Packs (HDSP), Serial Bus (SB1/SB2) RS-485 communications between cabinet monitoring units (CMU) and input/output modules, and hot-swappable modular cards.
Last updated: August 2026
4.2 Model 170 / 2070 & Advanced Transportation Controller (ATC) Cabinets
The architecture of traffic signal control cabinets has undergone massive technological transformations over the past five decades. Moving from traditional NEMA cabinet styles to standardized Caltrans Model 332 rack-mount systems , Model 2070 open-architecture controllers , and modern Advanced Transportation Controller (ATC) cabinet standards , hardware design has focused on modularity, field maintenance efficiency, low-voltage safety, and high-density input/output capabilities.
Caltrans 332 Cabinet Architecture & Rack Components
Originally standardized by the California Department of Transportation (Caltrans) and the Federal Highway Administration (FHWA), the Model 332 cabinet established an industry standard for 19-inch EIA rack-mounted traffic signal control equipment.
Component / Subassembly Model Designation Primary Operational Function in Cabinet
Power Distribution Assembly PDA #1 / PDA #2 Houses main circuit breakers, AC line filter, flash relay sockets, and DC power supply.
Dual Loop Detector Card Model 222 / 224 Slides into Input File; processes inductive loop sensor signals from field cables.
DC Isolation Card Model 242 Provides opto-isolated DC inputs for pedestrian pushbuttons and preemption detectors.
Solid-State Load Switch Model 200 Triac-based switch pack controlling 120 VAC Green, Yellow, and Red signal head circuits.
Solid-State Flasher Model 204 Dual-circuit flasher providing 50 to 60 flashes per minute for intersection flash mode.
Flash Transfer Relay (FTR) Model 430 Heavy-duty electromechanical relay transferring signal heads between load switch and flasher.
Monitor Unit Model 210 12-channel conflict monitor checking green/yellow conflicts and voltage levels.
Cabinet Sub-Structural Components
The 332 cabinet utilizes standardized multi-pin connectors to link the controller to internal rack components:
C1 Connector: The primary 104-pin multi-conductor connector routing discrete digital inputs (detectors, preemption) and outputs (load switch drive lines) between the controller unit and the Input/Output files.
C2 / C20 Connectors: Dedicated serial communication connectors providing RS-232 / RS-485 channels for modem connections, system master interconnects, and printer diagnostics.
C11 Connector: Dedicated connector routing load switch outputs directly to the Model 210 Conflict Monitor Unit.
Variations of the 332 cabinet include the Model 336 (a smaller, compact cabinet designed for pedestal mounting or limited right-of-way locations) and the Model 334 (configured specifically for ramp metering and ITS freeway monitoring applications).
Model 170 Logic Modules & Legacy Hardware
Introduced in the late 1970s, the Model 170 controller was designed as a non-proprietary, open-hardware specification. Built around an 8-bit Motorola 6800 or 68HC11 microprocessor , the Model 170 logic board contained minimal onboard memory (typically 32 KB to 64 KB).
Hardware Characteristics & Firmware Memory
Model 170 operating software (such as Caltrans TEES firmware, BiTran, or McCain software) was burned onto physical EPROM / PROM memory chips housed on removable memory modules:
Model 412 PROM Module: Prom card housing EPROM chips containing the intersection control software logic. Updating software required technicians to physically remove the EPROM chips using IC extraction tools, erase them under ultraviolet light, and re-program them with an EPROM burner.
Model 420 Memory Module: Expanded memory module providing non-volatile RAM backed by internal lithium batteries to preserve intersection timing parameters during power outages.
While highly reliable, Model 170 units lacked processing power for complex communications, high-resolution data logging, and advanced adaptive signal control algorithms.
Model 2070 Controller Architecture & VME Standards
To replace aging 170 controllers, Caltrans, TEES, and AASHTO developed the Model 2070 controller standard . Built on a modular 19-inch rack chassis, the 2070 architecture introduced powerful 32-bit microprocessors and high-speed internal bus systems.
Modular Sub-Chassis & VMEbus Architecture
Early 2070 units incorporated a VMEbus (Versa Module Eurocard) backplane (VME64), allowing modules from different manufacturers to interoperate within the same chassis:
2070-1B / 2070-1C CPU Module: High-performance 32-bit processor board (Motorola 68360 or PowerPC) running the OS-9 real-time operating system or embedded Linux . Features ethernet ports, datacomm serial ports, and flash memory.
2070-2A / 2070-2B Field I/O Module: Provides physical parallel interfaces matching Caltrans 332 C1/C11 connectors (2070-2A) or NEMA TS 2 AB connectors (2070-2B).
2070-7A Serial Comm Module: Dual RS-232 serial interface card for FSK modems, central system comms, and field master networking.
The 2070 architecture separated software from hardware, allowing traffic agencies to run third-party software applications on standard off-the-shelf controller hardware.
Advanced Transportation Controller (ATC) Cabinet Architecture
The ATC Cabinet Standard (ATC 5201 / ATC Cabinet v2.0) represents the modern pinnacle of traffic signal cabinet engineering, developed jointly by ITE, NEMA, and AASHTO.
Low-Voltage 48 VDC Architecture
The most radical safety innovation of the ATC Cabinet is the transition of cabinet internal control power and switch pack operation from dangerous 120 VAC line voltage down to safe 48 VDC low-voltage DC :
Technician Safety: Low-voltage 48 VDC eliminates arc flash hazards and fatal electric shock risks during field maintenance on active switch packs.
Thermal Efficiency: 48 VDC switching dramatically reduces heat dissipation inside the cabinet enclosure, extending electronic component lifespan.
High-Density Switch Packs & Serial Bus Architecture
ATC Cabinets eliminate bulky 120 VAC load switches and wiring harnesses in favor of compact, modular assemblies:
High-Density Switch Packs (HDSP): Compact solid-state modules providing quad-channel switching outputs in a fraction of the space required by legacy Model 200 load switches.
Serial Bus Architecture (SB1 / SB2): Internal high-speed RS-485 serial buses replace hundreds of discrete wires. A centralized Cabinet Monitoring Unit (CMU) communicates serially with Output Assembly modules and Input Assemblies.
Hot-Swappable Cards & Touchscreen Interfaces: All ATC subassemblies, including CMUs, switch packs, and input modules, are hot-swappable under power. Smart auxiliary display units (ADU) provide intuitive touch-screen diagnostic screens for rapid troubleshooting.