Study guide
4.7 Bicycle Signal Faces & MUTCD Flashing Operation
IMSA Traffic Signal Senior Field Technician Level III Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Adaptive Signal Control Technology (ASCT) & Modern Systems
1.1 ASCT Architecture & Operational Principles 1.2 Model-Based vs. Rule-Based ASCT Algorithms 1.3 ASCT Detection Layout & System Health Monitoring 1.4 Central Traffic Management Systems (ATMS) & Architecture
2 Chapter 2: Connected Vehicles (V2X), ITS Integration & Emerging Technologies
2.1 Connected Vehicle V2X Architecture & the 5.9 GHz Safety Spectrum 2.2 Roadside Unit Installation, GNSS Timing & SCMS Security 2.3 SPaT and MAP Message Structure under SAE J2735 2.4 Controller-to-RSU Interface, CV Applications & MAP Field Verification 2.5 Preemption vs. Priority and Transit Signal Priority Strategies 2.6 TSP Detection Architectures, Conditional Priority & Freight Priority 2.7 Automated Traffic Signal Performance Measures (ATSPMs)
3 Chapter 3: MUTCD Signal Warrants & Justification Studies
3.1 Traffic Studies & Engineering Data Collection 3.2 Vehicular Volume Warrants (Warrants 1, 2, and 3) 3.3 Pedestrian, School Crossing, and Network Warrants (Warrants 4, 5, and 8) 3.4 Coordinated, Crash Experience, Grade Crossing, and PHB Warrants (Warrants 6, 7, and 9)
4 Chapter 4: MUTCD Signal Equipment, Display & Visibility Standards
4.1 Signal Face Arrangements & MUTCD Lens Sizing 4.2 LED Optics, Backplates & Optical Shielding 4.3 Number of Signal Faces, the 20-Degree Placement Envelope & Sight Distance 4.4 Signal Face Mounting Heights, Lateral Offset & Distance from the Stop Line 4.5 Flashing Yellow Arrow Operation & Yellow Trap Elimination 4.6 Pedestrian Signal Displays, Countdown Modules, Interval Timing & APS 4.7 Bicycle Signal Faces & MUTCD Flashing Operation
5 Chapter 5: Advanced Traffic Detection Technologies & Configuration
5.1 Video Image Detection & Microwave Radar Detection 5.2 Thermal, Acoustic & Magnetometer Detection Technologies 5.3 Inductive Loop Physics, Geometry & Conductor Standards 5.4 Multi-Loop Arrays, Lead-In Cable & Pull-Box Splicing 5.5 Detector Testing, Tuning, Megohmmeter Diagnostics & Troubleshooting
6 Chapter 6: Traffic Communications & Fiber Optic Networks
6.1 Optical Waveguide Physics, Fiber Types & OSP Cable Construction 6.2 Optical Connectors, Polish Geometries & Redundant ITS Ring Topologies 6.3 Fiber Splicing, Optical Testing & Link Loss Budgets 6.4 Managed Industrial Ethernet in Traffic Cabinets 6.5 Copper, Twisted-Pair & Wireless Communications Media
7 Chapter 7: Actuated Phasing, Ring-Barrier Structure & Dual-Ring Operations
7.1 NEMA Dual-Ring Phasing, Barriers & Phase Compatibility 7.2 Lead-Lag Left Turns, the Yellow Trap & Signal Overlaps 7.3 Actuated Phase Parameters, Minimum Green, Passage Time & Termination 7.4 Recall Modes, Volume-Density Control & Parameter Diagnostics 7.5 Yellow Change & Red Clearance Interval Kinematics 7.6 Dilemma Zones, Pedestrian Interval Equations & a Full Field Calculation
8 Chapter 8: Coordinated Arterial Timing & Preemption Systems
8.1 Arterial Progression Principles & Actuated-Coordinated Operation 8.2 Time-Space Diagrams, Lead-Lag Sequencing & Transition Troubleshooting 8.3 Emergency Vehicle Preemption Technologies & Execution Sequence 8.4 Railroad Preemption Interconnects & Warning Time Calculations
9 Chapter 9: Electrical Codes, Grounding, Surge Protection & Power Distribution
9.1 NEC Articles, Underground Cover & Raceway Fill 9.2 Conductor Ampacity, Derating & NESC Overhead Clearances 9.3 Grounding, Bonding & Ground Resistance Testing 9.4 Transient Overvoltage, Surge Protective Devices & Cabinet Lightning Protection 9.5 Battery Backup Systems, Battery Chemistries & AC Branch Circuit Voltage Drop 9.6 Basic Electrical & Electronic Fundamentals for Signal Technicians
10 Chapter 10: NEMA TS1, TS2 & ATC Cabinet Architecture
10.1 NEMA TS1 vs. TS2 Architecture, SDLC Bus & BIUs 10.2 Malfunction Management Units (MMU) vs. Conflict Monitors (CMU) 10.3 Model 170/2070, ATC Architecture, Load Switches & Flashers
11 Chapter 11: Project Oversight, Quality Assurance, Maintenance & Troubleshooting
11.1 Civil, Raceway & Pole Construction Inspection Milestones 11.2 IMSA Cable Specifications, Cable Pulling, Acceptance Testing & As-Builts 11.3 Systematic Cabinet Troubleshooting & Diagnostic Instrumentation 11.4 Electrical Safety, Arc Flash Protection & Work Zone Traffic Control
4.7 Bicycle Signal Faces & MUTCD Flashing Operation
Key Takeaways Explain This Topic AI
MUTCD Chapter 4H permits a bicycle signal face only to control bicyclist movements from a designated bicycle lane or path, and forbids it where the movement shares an approach lane with motor vehicles or conflicts with another bicyclist movement.
A bicycle signal face shall consist entirely of bicycle symbol indications, requires an adjacent R10-41 series Bicycle Signal sign, and Section 4H.08 requires a supplemental near-side face whenever the primary face is more than 120 feet beyond the stop line.
Under Section 4G.01, flashing indications shall flash 50 to 60 times per minute with the illuminated period between one-half and two-thirds of the flash cycle, and the flashing mode shall not be terminated by removing or turning off the controller or the monitor.
During flashing operation all green indications shall be dark except a continuously displayed single-section GREEN ARROW, exactly one indication in every face shall flash, and flashing yellow may appear on more than one approach only if those approaches do not conflict.
Transitions into and out of flashing mode are Standards: no green or flashing yellow may be followed immediately by red without an intervening steady yellow, and the steady red clearance when leaving red-red flash should be at least 6 seconds.
Last updated: September 2026
4.7 Bicycle Signal Faces & MUTCD Flashing Operation
Note
Why this section exists : IMSA's Level III reference list requires familiarity with the current MUTCD in full, not just the warrant and display chapters. Two chapters are routinely skipped in signal training and routinely tested: Chapter 4H (Bicycle Signals) , which the 11th Edition added as a full chapter, and Chapter 4G (Flashing Operation) , which governs every flash event a technician will ever respond to.
1. Bicycle Signal Faces (MUTCD Chapter 4H)
A bicycle signal face is a signal face whose indications are bicycle symbols rather than circular or arrow indications. It exists to give a bicyclist movement its own right-of-way assignment, separate from the adjacent motor vehicle movement.
When a Bicycle Signal Face May Be Used
Section 4H.01 makes the use of a bicycle signal face an Option , not a requirement. The decision should be made during the engineering study required by Section 4C.01, Paragraph 1, for a new signal, or by engineering judgment at an existing signal. Two Standards bound the Option:
A bicycle signal face shall only be used to control bicyclist movements from a designated bicycle lane or path .
It shall only be used where the bicyclist movements it controls are separated from the movements it does not control.
Guidance in Paragraph 10 adds the operational test: where motor vehicles can make the same movement, a bicycle signal face should be used only if the bicyclist movement is sometimes allowed to proceed or is sometimes required to stop when the parallel motor vehicle movement is not . If the bicycle always does exactly what the adjacent through movement does, the bicycle face adds cost and clutter without adding control.
Prohibited Uses (Section 4H.02, all Standards)
# Prohibition
1 Shall not be used to control conflicting bicyclist movements from perpendicular or opposing approaches with the same face
- 2 Shall not be used for a bicyclist movement that shares an approach lane with motor vehicles
- 3 Shall not be used in any manner in the design or operation of a pedestrian hybrid beacon
Prohibition 2 is the one field crews violate most often, usually by retrofitting a bicycle face onto a shared through/bike lane where a bicycle box was striped.
Signing, Layout, Size & Placement
Bicycle Signal sign (Section 4H.03) : an R10-41 series Bicycle Signal sign shall be installed immediately adjacent to — including above or below — every bicycle signal face. Minimum size is 24 in × 36 in next to an overhead face and 12 in × 21 in next to a post-mounted face. It may be omitted next to a supplemental near-side face.
Layout (Section 4H.06) : a bicycle signal face shall consist of all bicycle symbol signal indications . Circular or arrow indications shall not be mixed into a bicycle signal face.
Size (Section 4H.07) : three nominal sizes are recognized — 4, 8, and 12 inches — all indications in a face shall be the same size, and 4-inch indications shall not be used for any bicycle signal face other than a supplemental, post-mounted, near-side face . This is the only place in Part 4 where a 4-inch indication is legitimate.
Placement (Section 4H.08) : Sections 4D.05 through 4D.08 apply, with three exceptions:
A minimum of one primary bicycle signal face is required, not two — an explicit exception to the two-face Standard of Section 4D.05.
The primary bicycle face shall have 8-inch or 12-inch indications , even at the near side.
When the primary face is more than 120 feet beyond the stop line , a supplemental near-side bicycle signal face shall be provided . Guidance adds that between 80 and 120 feet , a supplemental near-side face should be provided.
Separation (Guidance) : a bicycle face should be separated from the nearest vehicular face on the same approach by at least 3 feet , measured horizontally between face centers or vertically between the nearest indications.
Steady and Flashing Operation of Bicycle Faces
Section 4H.04 mirrors vehicular logic: a steady RED BICYCLE prohibits entry, a steady YELLOW BICYCLE shall follow a GREEN BICYCLE in the same face and shall be followed by a RED BICYCLE, and a steady GREEN BICYCLE is displayed only when the movement is permitted.
Section 4H.05 is the rule technicians most often get wrong: the mode of operation of the bicycle faces shall be the same as the mode of the other faces at that location. Bicycle faces operate steady when the intersection is steady and flash when the intersection flashes . A bicycle signal face shall not be placed in a dark mode while other vehicular faces are operating. Wiring a bicycle face so it goes dark on flash is a Standard violation, not an agency preference.
2. Flashing Operation (MUTCD Chapter 4G)
Flashing mode is not a failure state — it is a defined operating mode with its own Standards, and it is the state a cabinet enters on every monitor trip, every manual flash switch throw, and every scheduled late-night flash program.
Flash Rate and Mechanism (Section 4G.01, Standards)
- Requirement Value
- Flash rate Not less than 50 and not more than 60 times per minute
- Illuminated ("on") period Minimum 1/2 and maximum 2/3 of the total flash cycle
- Flasher Each signal shall have an independent flasher mechanism
Initiation A manual switch shall be provided , plus a conflict monitor / MMU circuit and, if appropriate, an automatic means
Persistence Flashing operation shall not be terminated by removing or turning off the controller unit, the monitor, or both
That last Standard is the design intent behind the flash transfer relay: flash must be a de-energized, fail-safe state that survives pulling the controller out of the cabinet. If a cabinet returns to steady operation when the controller is removed, it is non-compliant and unsafe.
Paragraph 7 is an Option: based on engineering study or judgment, a signal may be operated in flashing mode on a scheduled basis during one or more periods of the day.
Indications During Flash (Section 4G.03)
Guidance : use flashing yellow on the major street and flashing red on the other approaches , unless flashing red is used on all approaches.
Standard : all green indications shall be dark — not steady, not flashing — except a single-section continuously displayed GREEN ARROW used alone for a continuous movement, which shall remain continuously displayed during flash.
Standard : flashing yellow may be used on more than one approach only if those approaches do not conflict with each other .
Standard : one and only one indication in every signal face shall flash , except that a face with two identical CIRCULAR RED or RED ARROW indications may flash both.
Standard : if a face contains both circular and arrow indications of the colour to be flashed, only the circular indication shall be flashed .
Standard : all faces flashed on an approach shall flash the same colour , except that a separate turn face may flash RED ARROW while the adjacent through faces flash yellow. A shared turn face shall not flash CIRCULAR RED while the adjacent through movement flashes yellow.
Transitions Into and Out of Flash (Sections 4G.02 and 4G.04)
Entering flash from a monitor trip or a manual switch may happen at any time (Option). A programmed change into flash is constrained by Standard: it shall occur either at the end of the common major-street red interval, or directly from CIRCULAR GREEN to flashing CIRCULAR YELLOW, or from GREEN ARROW to flashing YELLOW ARROW, or from one flashing YELLOW ARROW section to another. And in every programmed change, no green or flashing yellow indication shall be terminated and immediately followed by a steady or flashing red without first displaying the steady yellow .
Leaving flash is equally constrained. From red-red flash , the flashing reds change to steady red, then to the green that begins the major-street green interval; Guidance sets the steady red clearance during that change at a minimum of 6 seconds . From yellow-red flash , the minor-street flashing reds go steady red immediately, and the major-street flashing yellows either go green in both directions or go steady yellow followed by a steady red clearance before green.
Caution
A cabinet that jumps from flashing yellow straight to red, or from flash straight to a green on the side street, is a Standard violation and a right-angle crash generator. When commissioning a scheduled flash program, always watch a full entry and exit sequence on site rather than trusting the controller's flash configuration screen.